The document provides instructions for mounting, wiring, and configuring the components of a Siemens Sinamics G120 frequency converter, including the power module, control unit, and operator panels. It describes connecting the power module to the motor and power supply, attaching the control unit, and wiring control terminals and inputs/outputs. It also provides guidelines for mounting the basic operator panel 2 or intelligent operator panel to complete the assembly and setup of the converter.
Giới thiệu biến tần Siemens Sinamics G120C
Biến tần Siemens Sinamics G120C là một dạng thiết kế hoàn toàn mới dạng compat. Sản phẩm có lối thiết kế nhỏ gọn để phù hợp lắp đặt trên máy hoặc trong tủ điện, vận hành dễ dàng. Các đầu nối được thiết kế ưu việt giúp lắp đặt dễ dàng. Phần mềm cài đặt nhanh và đơn giản.
Biến tần Siemens Sinamics G120C đặc biệt phù hợp sử dụng trong ngành chế tạo máy (OEM) và hệ thống bán hàng phân phối, nhờ đáp ứng hầu hết các ứng dụng như băng truyền, máy trộn, máy đùn, quạt, bơm, máy nén khí cùng nhiều ứng dụng khác.
Dải công suất của Biến tần Siemens Sinamics G120C
Dãy công suất: 3AC 380 – 480V, 0.55 – 132 kW
Chức năng chính của Biến tần Siemens Sinamics G120C
- Chế độ điều khiển: V/f, sensorless vector control (SLVC)
- Giao tiếp truyền thông: PROFINET, PROFIBUS DP, EtherNet/IP, USS/Modbus RTU
- Có khả năng kết nối với TIA Portal
- Có khả năng vận hành, chạy thử và chuẩn đoán lỗi trên thiết bị di động thông qua mạng không dây với mô-đun SINAMICS G120 Smart Access
- Tích hợp chức năng an toàn STO
- Cấp bảo vệ: IP20
Ưu điểm của biến tần Siemens Sinamics G120C
Mạnh mẽ: Hệ thống mạnh mẽ, nhỏ gọn, thích hợp cho các điều kiện môi trường xung quanh khắt khe.
- Tiết kiệm năng lượng: Giảm chi phí thông qua các chức năng tiết kiệm năng lượng như chế độ ECO và PROFIenergy.
Xử lý thuận tiện: Lắp ráp không phức tạp, dễ dạng cài đặt và sử dụng sản phẩm
- Tích hợp an toàn: Phù hợp với các tiêu chuẩn
Tự động hóa được tích hợp: Tích hợp tính năng trong tự động hóa
Ứng dụng của biến tần Siemens Sinamics G120C
Sinamics G120C là dòng biến tần được thiết kế hoạt động với độ chính xác và hiệu suất điều khiển cao, đáp ứng nhiều ứng dụng trong các như: Bơm nước truyền động phụ trợ, chế tạo máy, máy bơm ly tâm, quạt hướng tâm / hướng trục, máy nén, băng tải, máy đóng gói đơn giản, băng tải con lăn, gầu tải, cẩu trục, dầm biên, máy khuấy, tái chế, máy xay, máy trộn, máy nhào, máy nghiền, máy khuấy.
Bộ điều khiển PLC SIMATIC S7-1200 của Siemens là một sự lựa chọn thông minh cho các giải pháp tự động hóa nhỏ gọn với các tùy chọn mở rộng truyền thông và các chức năng tương thích khác.
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download các bài tập lớn với đề tài: Đo tốc độ động cơ dùng 8051, cho các bạn có thể tham khảo
Nhận viết luận văn đại học, thạc sĩ trọn gói, chất lượng, LH ZALO=>0909232620
Tham khảo dịch vụ, bảng giá tại: https://vietbaitotnghiep.com/dich-vu-viet-thue-luan-van
Download luận văn tốt nghiệp với đề tài: Thiết kế xây dựng bộ đếm xung, ứng dụng đo tốc độ động cơ trong hệ thống truyền động điện, cho các bạn làm luận văn tham khảo
Hạo Phương xin giới thiệu đến quý khách hàng cách cài đặt cơ bản dòng biến tần MD290. Biến tần Inovance MD290 là dòng sản phẩm đa năng rất dễ sử dụng và đem lại hiệu quả cho việc điều khiển tốc độ động cơ và các ứng dụng đặc biệt khác. Biến tần Inovance MD290 dùng cho các ứng dụng: điều khiển băng tải, bơm chân không kiểu piston, vận chuyển vật liệu, máy chế biến gỗ,…
Giới thiệu biến tần Siemens Sinamics G120C
Biến tần Siemens Sinamics G120C là một dạng thiết kế hoàn toàn mới dạng compat. Sản phẩm có lối thiết kế nhỏ gọn để phù hợp lắp đặt trên máy hoặc trong tủ điện, vận hành dễ dàng. Các đầu nối được thiết kế ưu việt giúp lắp đặt dễ dàng. Phần mềm cài đặt nhanh và đơn giản.
Biến tần Siemens Sinamics G120C đặc biệt phù hợp sử dụng trong ngành chế tạo máy (OEM) và hệ thống bán hàng phân phối, nhờ đáp ứng hầu hết các ứng dụng như băng truyền, máy trộn, máy đùn, quạt, bơm, máy nén khí cùng nhiều ứng dụng khác.
Dải công suất của Biến tần Siemens Sinamics G120C
Dãy công suất: 3AC 380 – 480V, 0.55 – 132 kW
Chức năng chính của Biến tần Siemens Sinamics G120C
- Chế độ điều khiển: V/f, sensorless vector control (SLVC)
- Giao tiếp truyền thông: PROFINET, PROFIBUS DP, EtherNet/IP, USS/Modbus RTU
- Có khả năng kết nối với TIA Portal
- Có khả năng vận hành, chạy thử và chuẩn đoán lỗi trên thiết bị di động thông qua mạng không dây với mô-đun SINAMICS G120 Smart Access
- Tích hợp chức năng an toàn STO
- Cấp bảo vệ: IP20
Ưu điểm của biến tần Siemens Sinamics G120C
Mạnh mẽ: Hệ thống mạnh mẽ, nhỏ gọn, thích hợp cho các điều kiện môi trường xung quanh khắt khe.
- Tiết kiệm năng lượng: Giảm chi phí thông qua các chức năng tiết kiệm năng lượng như chế độ ECO và PROFIenergy.
Xử lý thuận tiện: Lắp ráp không phức tạp, dễ dạng cài đặt và sử dụng sản phẩm
- Tích hợp an toàn: Phù hợp với các tiêu chuẩn
Tự động hóa được tích hợp: Tích hợp tính năng trong tự động hóa
Ứng dụng của biến tần Siemens Sinamics G120C
Sinamics G120C là dòng biến tần được thiết kế hoạt động với độ chính xác và hiệu suất điều khiển cao, đáp ứng nhiều ứng dụng trong các như: Bơm nước truyền động phụ trợ, chế tạo máy, máy bơm ly tâm, quạt hướng tâm / hướng trục, máy nén, băng tải, máy đóng gói đơn giản, băng tải con lăn, gầu tải, cẩu trục, dầm biên, máy khuấy, tái chế, máy xay, máy trộn, máy nhào, máy nghiền, máy khuấy.
Bộ điều khiển PLC SIMATIC S7-1200 của Siemens là một sự lựa chọn thông minh cho các giải pháp tự động hóa nhỏ gọn với các tùy chọn mở rộng truyền thông và các chức năng tương thích khác.
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download các bài tập lớn với đề tài: Đo tốc độ động cơ dùng 8051, cho các bạn có thể tham khảo
Nhận viết luận văn đại học, thạc sĩ trọn gói, chất lượng, LH ZALO=>0909232620
Tham khảo dịch vụ, bảng giá tại: https://vietbaitotnghiep.com/dich-vu-viet-thue-luan-van
Download luận văn tốt nghiệp với đề tài: Thiết kế xây dựng bộ đếm xung, ứng dụng đo tốc độ động cơ trong hệ thống truyền động điện, cho các bạn làm luận văn tham khảo
Hạo Phương xin giới thiệu đến quý khách hàng cách cài đặt cơ bản dòng biến tần MD290. Biến tần Inovance MD290 là dòng sản phẩm đa năng rất dễ sử dụng và đem lại hiệu quả cho việc điều khiển tốc độ động cơ và các ứng dụng đặc biệt khác. Biến tần Inovance MD290 dùng cho các ứng dụng: điều khiển băng tải, bơm chân không kiểu piston, vận chuyển vật liệu, máy chế biến gỗ,…
Giới thiệu về biến tần Siemens Sinamics G120
Biến tần Siemens Sinamics G120 là có thiết kế dạng modul gồm 2 phần là modul điều khiển (Control Unit – CU) và modul công suất (Power module – PM) . Đây là dòng biến tần có kích thước nhỏ gọn giúp tiết kiệm không gian lắp đặt, dải công suất mở rộng giúp tối ưu hoá việc lựa chọn, đáp ứng từng yêu cầu riêng biệt về ứng dụng, truyền thông và công suất.
Dải công suất của Biến tần Siemens Sinamics G120
- 1AC/3AC 200 – 240V, 0.55 – 4 kW (mô-đun công suất PM240-2)
- 3AC 200 – 240V, 5.5 … 55 kW (mô-đun công suất PM240-2)
3AC 380 – 480V, 0.55 – 250 kW (mô-đun công suất PM240-2)
- 3AC 380 – 480V, 7.5 … 90 kW (mô-đun công suất PM250)
- 3AC 500 – 690V, 11 – 250 kW (mô-đun công suất PM240-2)
Chức năng chính của Biến tần Siemens Sinamics G120
- Chế độ điều khiển: V/f, Vector control (điều khiển vòng kín) & điều khiển mô-men
- Điều khiển hồi tiếp PID
- Giao tiếp truyền thông: RS485/USS, PROFIBUS DP, CANopen, Modbus, BACnet
Có thể kết nối với máy tính qua cổng USB, BOP-2, IOP, MMC Card, SD Card
- Có khả năng kết nối với TIA Portal
- Chức năng trả năng lượng thừa về lưới (PM250)
- Có khả năng vận hành, chạy thử và chuẩn đoán lỗi trên thiết bị di động thông qua mạng không dây với mô-đun SINAMICS G120 Smart Access
- Các tính năng an toàn: STO, SS1, SBC, SLS, SDI, SSM
- Cấp bảo vệ: IP20
Ưu điểm của biến tần Siemens Sinamics G120
- Không ngừng cải tiến cả về phần cứng, phần mềm và các tùy chọn, biến tần Sinamics G120 có thể đáp ứng được các yêu cầu:
- Công nghệ an toàn, chức năng positioning, PFC và nhiều hơn,…
- Giảm lượng hàn tồn kho, dịch vụ đơn giản và nhanh chóng
- Hoạt động đáng tin cậy và tuổi thọ lâu dài
- PROFIenergy, phục hồi năng lượng
Vận hành, bảo trì bảo dưỡng và chuẩn đoán dễ dàng
- Tích hợp đầy đủ giao diện TIA
Ứng dụng của biến tần Siemens Sinamics G120
Sinamics G120 là dòng biến tần được thiết kế hoạt động với độ chính xác và hiệu suất điều khiển cao, đáp ứng nhiều ứng dụng trong các như: Công nghệ xây dựng, công nghiệp thực phẩm và đồ uống, truyền động phụ trợ, chế tạo máy, công nghiệp hóa chất, công nghiệp ô tô, xử lý gia công, dệt may, điều khiển chuyển động đơn trục, ngành tái chế.
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp ngành điện tự động công nghiệp với đề tài: Tổng về truyền động điện, đi sâu thiết mạch điều chỉnh tốc độ động cơ một chiều có đảo chiều công suất nhỉ cấp điện từ bộ biến đổi
Đồ án Đo và điều khiển tốc độ động cơ dùng 8051Vida Stiedemann
Hiện nay trong rất nhiều lĩnh vực đời sống và sản xuất các loại động cơ điện
ngày càng được ứng dụng rộng rãi hơn so với những loại động cơ sử dụng năng
lượng như xăng, dầu, khí đốt…..Những loại động cơ điện này có những ưu điểm
hơn hẳn về hiệu suất sử dụng, cấu tạo nhỏ gọn, giá thành hợp lý, dễ dàng điều
chỉnh tốc độ, đảo chiều, cưỡng bức các quá trình khởi động, quá trình hãm dừng dễ
dàng.Trong thực tế có rất nhiều loại động cơ điện được sử dụng bao gồm:
+Động cơ điện cơ điện 3 pha được chia làm các loại cơ bản là: Động cơ điện 3
pha dây quấn và 3 pha roto lồng sóc, động cơ điện 1 pha.
+Động cơ điện 1 chiều bao gồm các loại như: kích từ song song và loại kích từ
nối tiếp.
Thông thường với những động cơ thường xuyên đòi hỏi đảo chiều,tăng,
giảm, hãm dừng thì thương sử dụng động cơ điện 1 chiều là chủ yếu, vì sẽ dễ dàng
điều khiển hơn so với đông cơ xoay chiều. Để tiến hành điều khiển động cơ 1
chiều, có rất nhiều biện pháp được ứng dụng như là: thay đổi điện áp phần ứng,
thay đổi từ thông, hoặc sử dụng điện trở phụ mắc thêm vào phần ứng của động cơ.
Để làm được điều đó, chúng ta cần đi xây dựng những hệ thống điều khiển, có rất
nhiều hệ thống được ứng dụng như là: các hệ thống điều khiển PID, điều khiển
động cơ bằng Vi điều khiển, hay có thể điều khiển bằng cách sử dụng các loại khí
cụ điện. Trong đề tài này chúng em sẽ tiến hành nghiên cứu các quá trình điều
khiểu động cơ bằng phương pháp sử dụng Vi điều khiển họ 8051.
https://monhoc.vn/
Download luận văn đồ án tốt nghiệp ngành điện với đề tài: Tìm hiểu động cơ điện một chiều có từ thông đảo chiều không cổ góp có 2 nam châm vĩnh cửu, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế hệ thống đo nhiệt độ, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế hệ thống điều khiển tốc độ động cơ DC sử dụng bộ điều khiển PID và PID mờ (Fuzzy-PID), cho các bạn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download bài tập ngành kĩ thuật điện với đề tài: Động cơ không đồng bộ ba pha, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế bộ điều khiển tốc độ động cơ một chiều kích từ độc lập với mạch động lực sử dụng bộ băm xung khi không cần đảo chiều quay
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Đo và điều khiển tốc độ động cơ dùng 8051, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Tìm hiểu công nghệ hệ thống truyền động cho băng tải trong nhà máy bia, cho các bạn làm luận văn tham khảo
SPP-01 Super Parameter Programmer User Manual
Available at http://shop.ultisolar.com Paypal, Amazing Shipping freight to 100 countries and more. -Ultisolar New Energy Co., Ltd SWH Controllers||SWH Pump Stations||MPPT/PWM Solar Controllers||Flow Meter||Hall Flow Sensors||Heat Exchangers
Giới thiệu về biến tần Siemens Sinamics G120
Biến tần Siemens Sinamics G120 là có thiết kế dạng modul gồm 2 phần là modul điều khiển (Control Unit – CU) và modul công suất (Power module – PM) . Đây là dòng biến tần có kích thước nhỏ gọn giúp tiết kiệm không gian lắp đặt, dải công suất mở rộng giúp tối ưu hoá việc lựa chọn, đáp ứng từng yêu cầu riêng biệt về ứng dụng, truyền thông và công suất.
Dải công suất của Biến tần Siemens Sinamics G120
- 1AC/3AC 200 – 240V, 0.55 – 4 kW (mô-đun công suất PM240-2)
- 3AC 200 – 240V, 5.5 … 55 kW (mô-đun công suất PM240-2)
3AC 380 – 480V, 0.55 – 250 kW (mô-đun công suất PM240-2)
- 3AC 380 – 480V, 7.5 … 90 kW (mô-đun công suất PM250)
- 3AC 500 – 690V, 11 – 250 kW (mô-đun công suất PM240-2)
Chức năng chính của Biến tần Siemens Sinamics G120
- Chế độ điều khiển: V/f, Vector control (điều khiển vòng kín) & điều khiển mô-men
- Điều khiển hồi tiếp PID
- Giao tiếp truyền thông: RS485/USS, PROFIBUS DP, CANopen, Modbus, BACnet
Có thể kết nối với máy tính qua cổng USB, BOP-2, IOP, MMC Card, SD Card
- Có khả năng kết nối với TIA Portal
- Chức năng trả năng lượng thừa về lưới (PM250)
- Có khả năng vận hành, chạy thử và chuẩn đoán lỗi trên thiết bị di động thông qua mạng không dây với mô-đun SINAMICS G120 Smart Access
- Các tính năng an toàn: STO, SS1, SBC, SLS, SDI, SSM
- Cấp bảo vệ: IP20
Ưu điểm của biến tần Siemens Sinamics G120
- Không ngừng cải tiến cả về phần cứng, phần mềm và các tùy chọn, biến tần Sinamics G120 có thể đáp ứng được các yêu cầu:
- Công nghệ an toàn, chức năng positioning, PFC và nhiều hơn,…
- Giảm lượng hàn tồn kho, dịch vụ đơn giản và nhanh chóng
- Hoạt động đáng tin cậy và tuổi thọ lâu dài
- PROFIenergy, phục hồi năng lượng
Vận hành, bảo trì bảo dưỡng và chuẩn đoán dễ dàng
- Tích hợp đầy đủ giao diện TIA
Ứng dụng của biến tần Siemens Sinamics G120
Sinamics G120 là dòng biến tần được thiết kế hoạt động với độ chính xác và hiệu suất điều khiển cao, đáp ứng nhiều ứng dụng trong các như: Công nghệ xây dựng, công nghiệp thực phẩm và đồ uống, truyền động phụ trợ, chế tạo máy, công nghiệp hóa chất, công nghiệp ô tô, xử lý gia công, dệt may, điều khiển chuyển động đơn trục, ngành tái chế.
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp ngành điện tự động công nghiệp với đề tài: Tổng về truyền động điện, đi sâu thiết mạch điều chỉnh tốc độ động cơ một chiều có đảo chiều công suất nhỉ cấp điện từ bộ biến đổi
Đồ án Đo và điều khiển tốc độ động cơ dùng 8051Vida Stiedemann
Hiện nay trong rất nhiều lĩnh vực đời sống và sản xuất các loại động cơ điện
ngày càng được ứng dụng rộng rãi hơn so với những loại động cơ sử dụng năng
lượng như xăng, dầu, khí đốt…..Những loại động cơ điện này có những ưu điểm
hơn hẳn về hiệu suất sử dụng, cấu tạo nhỏ gọn, giá thành hợp lý, dễ dàng điều
chỉnh tốc độ, đảo chiều, cưỡng bức các quá trình khởi động, quá trình hãm dừng dễ
dàng.Trong thực tế có rất nhiều loại động cơ điện được sử dụng bao gồm:
+Động cơ điện cơ điện 3 pha được chia làm các loại cơ bản là: Động cơ điện 3
pha dây quấn và 3 pha roto lồng sóc, động cơ điện 1 pha.
+Động cơ điện 1 chiều bao gồm các loại như: kích từ song song và loại kích từ
nối tiếp.
Thông thường với những động cơ thường xuyên đòi hỏi đảo chiều,tăng,
giảm, hãm dừng thì thương sử dụng động cơ điện 1 chiều là chủ yếu, vì sẽ dễ dàng
điều khiển hơn so với đông cơ xoay chiều. Để tiến hành điều khiển động cơ 1
chiều, có rất nhiều biện pháp được ứng dụng như là: thay đổi điện áp phần ứng,
thay đổi từ thông, hoặc sử dụng điện trở phụ mắc thêm vào phần ứng của động cơ.
Để làm được điều đó, chúng ta cần đi xây dựng những hệ thống điều khiển, có rất
nhiều hệ thống được ứng dụng như là: các hệ thống điều khiển PID, điều khiển
động cơ bằng Vi điều khiển, hay có thể điều khiển bằng cách sử dụng các loại khí
cụ điện. Trong đề tài này chúng em sẽ tiến hành nghiên cứu các quá trình điều
khiểu động cơ bằng phương pháp sử dụng Vi điều khiển họ 8051.
https://monhoc.vn/
Download luận văn đồ án tốt nghiệp ngành điện với đề tài: Tìm hiểu động cơ điện một chiều có từ thông đảo chiều không cổ góp có 2 nam châm vĩnh cửu, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế hệ thống đo nhiệt độ, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế hệ thống điều khiển tốc độ động cơ DC sử dụng bộ điều khiển PID và PID mờ (Fuzzy-PID), cho các bạn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download bài tập ngành kĩ thuật điện với đề tài: Động cơ không đồng bộ ba pha, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Thiết kế bộ điều khiển tốc độ động cơ một chiều kích từ độc lập với mạch động lực sử dụng bộ băm xung khi không cần đảo chiều quay
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Đo và điều khiển tốc độ động cơ dùng 8051, cho các bạn làm luận văn tham khảo
Nhận viết luận văn Đại học , thạc sĩ - Zalo: 0917.193.864
Tham khảo bảng giá dịch vụ viết bài tại: vietbaocaothuctap.net
Download luận văn đồ án tốt nghiệp với đề tài: Tìm hiểu công nghệ hệ thống truyền động cho băng tải trong nhà máy bia, cho các bạn làm luận văn tham khảo
SPP-01 Super Parameter Programmer User Manual
Available at http://shop.ultisolar.com Paypal, Amazing Shipping freight to 100 countries and more. -Ultisolar New Energy Co., Ltd SWH Controllers||SWH Pump Stations||MPPT/PWM Solar Controllers||Flow Meter||Hall Flow Sensors||Heat Exchangers
시크 SICK Lector63x 2D DPM스캐너 고정식바코드스캐너 산업용바코드리더 이미지스캐너 매뉴얼HION IT
Lector63x 시리즈 제품군
Lector631
Lector632
2메가픽셀 센서 장착 코드 리더
렌즈 및 필터 디자인의 유연성
교체 가능한 내장형 High-Power 조명
기능 버튼, 레이저 조준 보조장치, 음향 피드백 신호 및 피드백 LED
고분해능 센서와 지능적 처리로 어려운 판독 조건에서도 최고의 판독 성능을 보장합니다.
구성이 유연한 광학 디자인과 고성능 조명으로 고속에서나 판독 거리가 먼 애플리케이션에서도 작은 코드를 판독할 수 있습니다.
직관적 인터페이스, 장치 장착을 신속하게 해주는 기능 버튼, 내장된 조명과 조준 레이저 덕분에 신속하고 용이한 커미셔닝
음향 신호와 물체 위 컬러 피드백 스폿으로 즉각적 결과 점검 가능
microSD 메모리 카드로 간단하게 복제 기능을 활용할 수 있어 생산 라인 장애 시 기계 작동 정지 시간이 감소됨
FEATURES
Focus : Adjustable focus (manually)
Sensor : CMO S matrix sensor, gray scale values
Light source ;
To be ordered separately as accessory
Aiming laser: visible red light (λ = 630 nm ... 680 nm)
Laser class : 1, complies with 21 CFR 1040.10 except for the tolerance according to “Laser Notice No. 50”from June 24, 2007 (IEC 60825-1 (2007-3))
Scanning frequency : ≤ 50 Hz, at 1.9 megapixels resolution
Code resolution : ≥ 0.1 mm 1)
Reading distance : 50 mm ... 2,200 mm
PERFORMANCE
Bar code types : GS1-128 / EAN 128, UPC / GTIN / EAN, Interleaved 2 of 5, Pharmacode, GS1 DataBar, Code 39, Code 128, Codabar, Code 32, Code 93, USPS (Postnet, Planet, USPS4SCB), Australian Post, Dutch KIX Post, Royal Mail, Swedish Post
2D code types : Data Matrix ECC 200, GS1 Data-Matrix, MaxiCode, QR code
Stacked code types : PDF 417
Code qualification : On the basis of ISO/IEC 16022, ISO/IEC 15415, ISO/IEC 18004
INTERFACES
Serial (RS-232, RS-422) ;
Function : Host, AUX
Data transmission rate : 300 Baud ... 115.2 k Baud, AUX: 57.6 kBaud (RS-232)
USB : USB 2.0
Ethernet ;
Function : Host, AUX, image transmission
Data transmission rate : 10/100/1,000 Mbit/s
Protocol : TCP/IP, FTP (image transmission), EtherNet/IP, PROFINET (optional over external fieldbus module CDF 600-2)
CAN bus ;
Function : SICK CAN sensor network (Master/Slave, Multiplexer/Server)
Data transmission rate : 250 kbit/s ... 500 kbit/s
Protocol : CSN (SICK CAN Sensor Network)
PROFIBUS DP : Optional over external fieldbus module (CDF600-2)
Switching inputs : 4 (“Sensor 1”, “Sensor 2”, 2 inputs via optional CMC600 parameter memory in CDB650/CDM 420)
Configurable inputs : Encoder input, external trigger
Switching outputs : 6 (CDB650: “Result 1”, “Result 2”, “Result 3”, “Result 4”, 2 external outputs via CMC600 or CDM420: “Result 1”, “Result 2”, 2 external outputs via CMC600 or cable with open end:“Result 1”, “Result 2”, “Result 3”, “Result 4”)
“device ready”
Reading pulse : Switching inputs, non-powered, serial interface, Ethernet, CAN , auto pulse, presentation mode
Optical indicators : 11 LEDs (5 x status display, 5 x LED bar graph, 1 green/red feedback spot)
Acoustic indicators : Beeper (configurable)
Control elements : 2 buttons
Configuration software : SOPAS ET
Memory card : Micro SD memory card (flash card) max. 32 GB , optional
>하이온아이티
주소 : 서울 금천구 가산디지털2로 165, 1304호 (백상스타타워2차)
대표번호 : 02-2038-0018 / 이메일 : hion@hionit.com
홈페이지 : http://hionsmart.com
Siemens s7 300-400-hb-cpu31x_c_und_cpu31x_eDien Ha The
Siemens,
Catalog Thiết Bị Tự Động Siemens, Catalog Thiết Bị Tự Động
Catalog Phụ Kiện Siemens, Catalog Phụ Kiện,
Catalog Siemens, Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Siemens vui lòng gọi: 0907.764.966
Tự Động Hóa Siemens,
Catalog Thiết Bị Điện Tự Động Hóa Siemens,
Catalog Phụ Kiện Tự Động Hóa Siemens,
Catalog Tự Động Hóa Siemens,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Tự Động Hóa Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Tự Động Hóa Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Tự Động Hóa Siemens vui lòng gọi: 0907.764.966
Tự Động Hóa Siemens,
Catalog Thiết Bị Điện Tự Động Hóa Siemens,
Catalog Phụ Kiện Tự Động Hóa Siemens,
Catalog Tự Động Hóa Siemens,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Tự Động Hóa Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Tự Động Hóa Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Tự Động Hóa Siemens vui lòng gọi: 0907.764.966
Siemens,
Catalog Thiết Bị Điện Siemens, Catalog Thiết Bị Điện,
Catalog Phụ Kiện Siemens, Catalog Phụ Kiện,
Catalog Siemens, Catalog,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Siemens vui lòng gọi: 0907.764.966
STONE Tech is a manufacturer of HMI display module(Intelligent TFT LCD). We provide LCD modules/LCD Displays, Graphic LCM, smart Display LCD, TFT LCM, Custom LCD Module Display, and LCD panels. china LCD Manufacturers.
Similar to Tài liệu đào tạo simens sinamic G120 (20)
Ưu điểm của AC Servo Siemens Sinamics V90
HIỆU SUẤT TỐI ƯU
Tính năng Tuning một lần và cho phép tuning theo thời gian thực giúp tối ưu hóa hiệu suất của hệ thống.
Tần số xung ngõ vào cao lên đên 1MHz.
Encoder khác nhau giúp đáp ứng các yêu cầu ứng dụng khác nhau.
DỄ SỬ DỤNG
Kết nối đơn giản với hệ thống điều khiển
Điều chỉnh dể dàng và nhân bản thông số
Vận hành dễ dàng với SINAMICS V-ASSISTANT
Tích hợp dễ dàng qua PTI, PROFINET, USS, Modbus RTU
TIẾT KIỆM CHI PHÍ
Tích hợp: Pulse train positioning, internal positioning với traversing block hoặc Modbus
Tích hợp điện trở phanh trong tất cả các kích thước khung
Tích hợp holding brake switch (Frame size 400V)
HOẠT ĐỘNG TIN CẬY
Vòng bi motor chất lượng cao
Tiêu chuẩn cấp độ bảo vệ cho tất cả các loại motor IP65
Tích hợp tính năng bảo vệ Torque Off (STO)
Hệ thống AC Servo Siemens Sinamics V90 là Driver dòng Servo cơ bản của Siemens kết hợp với Motor S-1FL6, có thể thực hiện được những yêu cầu điều khiển phức tạp và điều khiển động cơ với độ chính xác cao.
Brochure bộ lập trình PLC Siemens S7-1200
Bộ điều khiển PLC SIMATIC S7-1200 của Siemens là một sự lựa chọn thông minh cho các giải pháp tự động hóa nhỏ gọn với các tùy chọn mở rộng truyền thông và các chức năng tương thích khác.
Hoàng Gia Automation xin gửi đến quý khách hàng hướng dẫn cài đặt bộ điều khiển siemens simatic logo!.
Trong file tài liệu có hướng dẫn chi tiết đầy đủ cách lắp đặt, cài đặt bộ điều khiển. Để biết thêm chi tiết sản phẩm, truy cập website: www.hgautomation.vn
Bộ lập trình PLC Siemens Simatic S7-1500 là bộ điều khiển lập trình PLC cao cấp thế hệ mới của Siemens. với đầy đủ các tính năng điều khiển và truyền thông giúp tối ưu hóa hoạt động của máy, dễ dàng sử dụng trong nhiều lĩnh vực công nghiệp khác nhau.
Giới thiệu biến tần Simens Sinamics S120
Biến tần Simens Sinamics S120 là bộ điều khiển có khả năng vận hành cao và ứng dụng điều khiển linh động, được thiết kế nhằm đáp ứng cho các ứng dụng phức tạp, yêu cầu độ chính xác cao.
Biến tần SINAMICS S120 lý tưởng cho các nhu cầu các ứng dụng đơn trục (single axis) và đa trục (multi axis), được sử dụng trong các giải pháp truyền động tùy chỉnh nhờ vào thiết kế dạng mô-đun khi phần chỉnh lưu (Line Module) và phần nghịch lưu (Motor Module) là hai mô-đun riêng biệt tách rời và được điều khiển qua Module điều khiển (Control Unit).
Ngoài ra biến tần Sinamics S120 còn có khả năng trả năng lượng về lưới (Regenerative) thông qua việc sử dụng khối mô-đun chỉnh lưu (Line Module) phù hợp với nhu cầu và mục đích của từng ứng dụng cụ thể
Dải công suất của Biến tần Siemens Sinamics S120
Dãy công suất biến tần theo điện áp:
1AC/3AC 200 – 240V, 0.55 – 4 kW
- 3AC 200 – 240V, 5.5 … 55 kW
- 3AC 380 – 480V, 0.55 – 250 kW
- 3AC 500 – 690V, 11 – 250 kW
Chức năng chính của Biến tần Siemens Sinamics S120
- Chế độ điều khiển: V/f, Vector control, điều khiển servo
- Điều khiển hồi tiếp PID
Loại điều khiển trục đơn: có 2 thiết kế Blocksize (AC/AC) và Chassis (AC/AC)
- Loại điều khiển nhiều trục: có 3 thiết kế Blocksize (DC/AC), Blocksize Compact (DC/AC) và Chassis (DC/AC)
Giao tiếp truyền thông: PROFINET, PROFIBUS DP, EtherNet/IP, USS (kein CU310), CANopen (CU320-2), Modbus TCP
- Có khả năng kết nối với TIA Portal
- Chức năng trả năng lượng thừa về lưới
- Biến tần SINAMICS S120 có thể hỗ trợ nhiều loại loại động cơ: động cơ đồng bộ, động cơ không đồng bộ, động cơ servo…
- Hỗ trợ nhiều chuẩn encoder khác nhau
- Phần mềm cấu hình và giám sát thời gian thực: SIZER, STARTER, DT Configurator
Các tính năng an toàn: STO, SS1, SBC, SOS, SS2, SLS, SSM, SDI, SLP, SP, SBT, SLA, SCA
Cấp bảo vệ: IP20
Tính năng nổi trội của Biến tần Siemens Sinamics S120
- Cấu trúc Module đáp ứng những yêu cầu chuyển động phức tạp, độc lập hoặc là phối hợp nhiều chuyển động.
- Tích hợp tất cả các chức năng an toàn
- Tự động cấu hình và tự động điều khiển tối ưu
- Dễ dàng kết nối với các thiết bị điều khiển cấp cao hơn
- Sinamics S120 được thiết kế dùng cho 2 loại motor servo và motor không đồng bộ với công suất thiết kế lên đến 800kW. ------ Ngoài ra còn hỗ trợ kết nối với hầu hết các loại encoder.
Ứng dụng của Biến tần Siemens Sinamics S120
- Sinamics S120 là dòng biến tần được thiết kế hoạt động với độ chính xác và hiệu suất điều khiển cao, đáp ứng nhiều ứng dụng trong các như: Máy đóng gói, nhựa, máy in, dệt, chế biến gỗ, gốm sứ, thuỷ tinh, máy công cụ, công nghiệp sản xuất thép, hệ thống nâng hạ và cẩu trục…
Giới thiệu biến tần Siemens Sinamics G120X
Biến tần Siemens Sinamics G120X là dòng sản phẩm được phát triển với các tính năng nâng cao cho ngành nước và các ứng dụng HVAC ở phân khúc tầm trung. G120X cung cấp dải công suất rộng từ 0,75 đến 630 kW với các cấp điện áp và mức độ bảo vệ đa dạng, tích hợp các giải pháp tối ưu, thời gian thiết lập nhanh chóng, hoạt động cực kỳ đơn giản.
Dải công suất của biến tần Siemens Sinamics G120X
Dãy công suất:
- 3AC 380 – 480V: 0.75 ~ 560 kW
- 3AC 500 – 690V: 3 ~ 630 kW
Chức năng chính của Biến tần Siemens Sinamics G120X
- Chế độ điều khiển: V/f, sensorless vector control (SLVC)
- Giao tiếp truyền thông: PROFINET, PROFIBUS, EtherNet/IP, Modbus RTU, USS, BACnet
- Có khả năng kết nối lên tới 8 biến tần cùng lúc. Chức năng điều khiển bơm và quạt được tối ưu
- Điều khiển theo thời gian thực
- Có khả năng vận hành, chạy thử và chuẩn đoán lỗi trên thiết bị di động thông qua mạng không dây với mô-đun SINAMICS G120 Smart Access
- Khả năng quá tải: tải nặng 150% trong 10s, tải nhẹ: 110% trong 60s
- Tích hợp chức năng an toàn: STO
- Cấp bảo vệ: IP20
Tính năng nổi trội của Biến tần Siemens Sinamics G120X
- ĐIỀU KHIỂN ĐA BƠM
Cho phép điều khiển nhiều bơm nhỏ, thay vì một máy bơm lớn
Điều khiển tối đa 2 (+4 bơm khi có module I/O rời) bằng bộ điều khiển PID tích hợp, sử dụng:
- Chế độ chuyển bơm tự động
- Chế độ dừng, gọi bơm.
- Chế độ bảo trì bơm.
BẢO VỆ NGƯNG TỤ VÀ SƯƠNG GIÁ
- Bảo vệ sự ngưng tụ:
Động cơ trong môi trường ẩm và lạnh có thể hình thành hiện tượng ngưng tụ hơi nước gây hỏng động cơ..
Có thể tránh được sự cố này bằng cách tăng nhẹ nhiệt độ bề mặt động cơ bằng cách tạo dòng điện một chiều để giữ động cơ ấm nhằm ngăn ngừa sự ngưng tụ.
Chống Đông:
Nước đóng băng bên trong máy bơm có thể gây hư hỏng. Chuyển động chậm của cánh quạt trong khi không hoạt động hoặc khi nhiệt độ xung quanh giảm xuống dưới ngưỡng có thể ngăn ngừa hư hỏng.
BẢO VỆ CHỐNG XÂM THỰC
Cánh quạt của máy bơm có thể bị hỏng do bọt khí nhỏ tạo ra do khe hở áp suất khi máy bơm chạy ở tốc độ cao và không thể cung cấp nước theo yêu cầu.
Chế độ này tạo ra một cảnh báo khi đạt tới ngưỡng áp suất xâm thực. Nếu biến tần không nhận được phản hồi từ đầu dò bơm, nó sẽ hoạt động để ngăn chặn sự xâm thực hư hại.
BẢO VỆ BƠM CHẠY KHÔ, TẮC NGHẼN BƠM
Biến tần có thể theo dõi tốc độ, dòng điện và mô-men xoắn của động cơ để xác định các tình huống tải bất thường:
Mô-men xoắn không đủ có thể cho thấy bơm rò rỉ hoặc chạy khô
Mô-men xoắn (và dòng điện) quá mức cùng với tốc độ thấp có thể cho thấy sự tắc nghẽn của bơm
CHẾ ĐỘ HỎA HOẠN
Trong chế độ hỏa hoạn, biến tần cố gắng vận hành động cơ càng lâu càng tốt (bỏ qua tín hiệu TẮT) bất chấp điều kiện môi trường xung quanh không bình thường để cải thiện lưu thông không khí và thời gian tồn tại trong các tình huống quan trọng
Ứng dụng của biến tần Siemens Sinamics G120X
Biến tần SINAMICS G120X chuyên dụng cho các ứng dụng máy bơm và quạt trong ngành xử lý nước và HVAC
Biến tần Siemens Sinamics G120 không ngừng cải tiến cả về phần cứng, phần mềm và các tùy chọn đáp ứng các yêu cầu:
Giảm chi phí thông qua module
Mạnh mẽ
Dễ sử dụng
Tích hợp tính năng an toàn
Tích hợp đây đủ TIA
Giới thiệu về biến tần Siemens Sinamics V20
Biến tần Siemens Sinamiscs V20 là dòng biến tần phổ thông của Siemens với những ưu điểm đa năng, nhỏ gọn , lắp đặt đơn giản, dễ sử dụng và tiết kiệm chi phí, độ tin cậy cao và dễ dàng sử dụng cho các ứng dụng cơ bản. Khả năng kết nối với máy tính qua nhiều cổng khác nhau thích hợp sử dụng trong nhiều lĩnh vực.
Dải công suất của Biến tần Siemens Sinamics V20
- 1 Pha 220V từ 0,12 kW tới 3 kW
- 3 Pha 380V, từ 0,37 kW tới 30 kW
Ưu điểm của Biến tần Siemens Sinamics V20
Dễ dàng lắp đặt
- Lắp đặt: Gần cạnh bên nhau, treo hoặc âm vào tường. 1AC230V FSAD Mới có thể làm tủ nhỏ hơn 32% so với 1AC230V FSC cũ, thiết kế Nhỏ gọn và lắp đặt Linh hoạt.
Chuẩn truyền thông: USS và MODBUS RTU lựa chọn với đầy đủ tính linh hoạt và frame truyền. Tích hợp dễ dàng trong hệ thống hiện có. Hỗ trợ thực hiện thao tác kết nối macro và kết nối thư viện tiêu chuẩn.
- EMC và IT grid support: 1AC230V V20 FSAA/B/C/D với Category C1 Bộ lọc đáp ứng tiêu chuẩn môi trường EMC . Phiên bản không có bộ lọc 1AC230V FSAA/B/C/D và 3AC400V cũng có thể làm việc với IT network.
Dễ dàng sử dụng
- Kết nối Macro: Thao tác cài đặt theo ứng dụng được tối ưu hóa và nhanh chóng với kết nối Macro.
- Tạo nhiều nhóm thông số: Dễ chuyển đổi thông số cài đặt với bất kỳ biến tần nào cùng khung kích thước. Thẻ nhớ lên đến 32G SD.
Chế độ Keep running: Năng suất cao hơn trong sản xuất nhờ khả năng tự động điều chỉnh trong trường hợp nguồn cung cấp dây chuyền không ổn định.
- Mạnh mẽ: Dải điện áp rộng hơn, phạm vi nhiệt độ môi trường xung quanh -10C đến 60C cho tất cả nguồn điện, thiết kế làm mát tốt hơn và được phủ PCB làm tăng độ chắc chắn về chất lượng của biến tần.
Dễ dàng tiết kiệm chi phí:
- Chế độ điều khiển ECO và chế độ NGỦ ĐÔNG: Tinh chỉnh phù hợp với ứng dụng và điều chỉnh từ thông để tiết kiệm năng lượng. Tích hợp các chức năng tiết kiệm năng lượng cho chế độ chờ
- Đo năng lượng tiêu thụ: Ước tính mức tiêu thụ và tiết kiệm năng lượng.
- Mức quá tải – Thấp: Với chu kỳ quá tải thấp, kích thước khung E V20 có thể đạt công suất và dòng điện đầu ra cao hơn. Một biến tần nhỏ hơn có thể được sử dụng.
- Free function blocks: Với tài nguyên phần mềm hạn chế, chức năng này giúp mở rộng tính linh hoạt hơn cho các ứng dụng mà không cần đầu tư..
Ứng dụng – Giải pháp của Siemens Sinamics V20
Biến tần Siemens Sinamics V20 là dòng biến tần chuyên dụng cho cac chuỗi chuyển động đơn giản như: Bơm ly tâm, quạt, máy nén, hệ thống bơm năng lượng mặt trời, băng chuyền, băng tải con lăn, băng tải xích.
Giới thiệu về bộ điều khiển Siemens Simatic LOGO!
Bộ điều khiển Simens Simatic LOGO! thường được gọi Controller hoặc NanoController, có nguyên lý hoạt động tương tự PLC. Với Simatic LOGO!, Siemens đem đến bộ điều khiển lý tưởng cho các giải pháp tự động trong công nghiệp và xây dựng. Thiết kế dạng module làm cho LOGO! trở nên cực kỳ linh hoạt, các model của LOGO! cho phép cấu hình hệ thống đáp ứng nhu cầu của khách hàng.
Đặc tính kỹ thuật của bộ điều khiển Siemens Simatic LOGO!
- Mở rộng I/O
- Cho phép kết nối các module I/O (gồm DI+DO, AI, AO)
- Mở động tối đa lên đến: Dạng số (20 ngõ vào và 16 ngõ ra), Analog (8 ngõ vào, 8 ngõ ra)
Tính năng
- Mạch điện nhỏ gọn hơn, đấu nối đơn giản hơn
- Đồng bộ hóa thời gian
- Module có sẵn ở các dải điện áp
- Có thể lập trình và giao tiếp bằng cáp Ethernet
- Nhiệt độ hoạt động từ 0° đến 55°C
Truyền thông
- Tích hợp cổng truyền thông Ethernet với chuẩn SIMATIC S7 / Modbus 10/100 Mbit/s TCP/IP
Bảo mật
- Bảo vệ download/upload chương trình PLC bằng Password
Web Server
- Cho phép lập trình giao diện web server
- Cho phép kết nối từ xa giữa PC và CPU
- Vùng nhớ CPU: Bao gồm 2 vùng nhớ:
- Program Memory: lưu chương trình máy. Tối đa 8500 byte.
- Retentive Memory: Vùng nhớ lưu dữ liệu khi mất điện. Tối đa 250 vùng nhớ lưu.
Thẻ nhớ
- Cho phép gắn memory card để upload, download chương trình từ Logo!
- Lưu dữ liệu data log
Ứng dụng – Giải pháp của bộ điều khiển Siemens Simatic LOGO!
Bộ điều khiển Siemens Simatic LOGO! được ứng dụng rộng rãi trong các lĩnh vực như:
- Máy đơn (máy bơm, máy ép nhỏ, máy nén, bệ nâng, băng tải…)
- Nông nghiệp
- Nhà thông minh
- Phòng cháy chữa cháy,…
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdfPaige Cruz
Monitoring and observability aren’t traditionally found in software curriculums and many of us cobble this knowledge together from whatever vendor or ecosystem we were first introduced to and whatever is a part of your current company’s observability stack.
While the dev and ops silo continues to crumble….many organizations still relegate monitoring & observability as the purview of ops, infra and SRE teams. This is a mistake - achieving a highly observable system requires collaboration up and down the stack.
I, a former op, would like to extend an invitation to all application developers to join the observability party will share these foundational concepts to build on:
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
Welocme to ViralQR, your best QR code generator.ViralQR
Welcome to ViralQR, your best QR code generator available on the market!
At ViralQR, we design static and dynamic QR codes. Our mission is to make business operations easier and customer engagement more powerful through the use of QR technology. Be it a small-scale business or a huge enterprise, our easy-to-use platform provides multiple choices that can be tailored according to your company's branding and marketing strategies.
Our Vision
We are here to make the process of creating QR codes easy and smooth, thus enhancing customer interaction and making business more fluid. We very strongly believe in the ability of QR codes to change the world for businesses in their interaction with customers and are set on making that technology accessible and usable far and wide.
Our Achievements
Ever since its inception, we have successfully served many clients by offering QR codes in their marketing, service delivery, and collection of feedback across various industries. Our platform has been recognized for its ease of use and amazing features, which helped a business to make QR codes.
Our Services
At ViralQR, here is a comprehensive suite of services that caters to your very needs:
Static QR Codes: Create free static QR codes. These QR codes are able to store significant information such as URLs, vCards, plain text, emails and SMS, Wi-Fi credentials, and Bitcoin addresses.
Dynamic QR codes: These also have all the advanced features but are subscription-based. They can directly link to PDF files, images, micro-landing pages, social accounts, review forms, business pages, and applications. In addition, they can be branded with CTAs, frames, patterns, colors, and logos to enhance your branding.
Pricing and Packages
Additionally, there is a 14-day free offer to ViralQR, which is an exceptional opportunity for new users to take a feel of this platform. One can easily subscribe from there and experience the full dynamic of using QR codes. The subscription plans are not only meant for business; they are priced very flexibly so that literally every business could afford to benefit from our service.
Why choose us?
ViralQR will provide services for marketing, advertising, catering, retail, and the like. The QR codes can be posted on fliers, packaging, merchandise, and banners, as well as to substitute for cash and cards in a restaurant or coffee shop. With QR codes integrated into your business, improve customer engagement and streamline operations.
Comprehensive Analytics
Subscribers of ViralQR receive detailed analytics and tracking tools in light of having a view of the core values of QR code performance. Our analytics dashboard shows aggregate views and unique views, as well as detailed information about each impression, including time, device, browser, and estimated location by city and country.
So, thank you for choosing ViralQR; we have an offer of nothing but the best in terms of QR code services to meet business diversity!
Generative AI Deep Dive: Advancing from Proof of Concept to ProductionAggregage
Join Maher Hanafi, VP of Engineering at Betterworks, in this new session where he'll share a practical framework to transform Gen AI prototypes into impactful products! He'll delve into the complexities of data collection and management, model selection and optimization, and ensuring security, scalability, and responsible use.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
A tale of scale & speed: How the US Navy is enabling software delivery from l...sonjaschweigert1
Rapid and secure feature delivery is a goal across every application team and every branch of the DoD. The Navy’s DevSecOps platform, Party Barge, has achieved:
- Reduction in onboarding time from 5 weeks to 1 day
- Improved developer experience and productivity through actionable findings and reduction of false positives
- Maintenance of superior security standards and inherent policy enforcement with Authorization to Operate (ATO)
Development teams can ship efficiently and ensure applications are cyber ready for Navy Authorizing Officials (AOs). In this webinar, Sigma Defense and Anchore will give attendees a look behind the scenes and demo secure pipeline automation and security artifacts that speed up application ATO and time to production.
We will cover:
- How to remove silos in DevSecOps
- How to build efficient development pipeline roles and component templates
- How to deliver security artifacts that matter for ATO’s (SBOMs, vulnerability reports, and policy evidence)
- How to streamline operations with automated policy checks on container images
2. 2
Required System Configuration CD-ROM
• Processor with min. 2 GHz (dual core recommended)
• 1024 MB RAM
• Graphics card (min. 256 MB memory recommended)
• Screen resolution: 1280 x 1024 px
• Operating Systems:
Microsoft® Windows™ XP (Service Pack 2 or later)
Microsoft® Windows™ Vista
Microsoft® Windows™ 7
I_DT_G120_Booklet_RZ.indd 2 04.04.2012 13:11:27
3. 3
This booklet contains the same information as the attached CD. Still, we highly recommend to work through the learn-
ing program before consulting the booklet. The multimedia tutorial is a comfortable and easy to understand introduc-
tion to the converter family SINAMICS G120.
04/2012
6FC5095-0AA85-0BA0
SINAMICS G120
Training Booklet
I_DT_G120_Booklet_RZ.indd 3 04.04.2012 13:11:28
4. Materials and tools
The components listed below are presented in this booklet. To test your knowledge on the actual
product, you have the choice between the following order alternatives:
Training case
Product
• SINAMICS G120 training case*
Order no.
6ZB2480-0CJ00
Single components
Product
• SINAMICS G120 PM240-2 FSA 0.55kW
• SINAMICS G120 CU240E-2
• Motor (0.55 kW)
• SINAMICS PC Connection Kit-2
• SINAMICS BOP-2
• Intelligent Operator Panel IOP
• Screening kit 2
Order no.
6SL3210-1PE11-8AL0
6SL3244-0BB12-1BA1
1LA7096-4AA10
6SL3255-0AA00-2CA0
6SL3255-0AA00-4CA1
6SL3255-0AA00-4JA0
6SL3264-1EA00-0HA0
Optional components
Product
• IOP/BOP-2 door mounting kit
Order no.
6SL3256-0AP00-0JA0
In addition, you will need the following equipment:
• PC with USB interface
• Switches – commercially available*
• Potentiometer – commercially available*
•
Various M4 screws and nuts (length depends on installation location) with suitable screwdriver/
wrench – commercially available*
*
The training case is a complete demo station including a motor, the power module of the converter, switches, lights and
a 230 V power supply connection.
I_DT_G120_Booklet_RZ.indd 4 04.04.2012 13:11:28
5. Safety instructions
Validity
These instructions apply to the following converter:
Product
SINAMICS G120
Prerequisites
You are proficient in working with the Microsoft® Windows™ operating system.
You are conversant with the principles of electronics and electrical engineering.
Warning
Dangerous currents and voltages!
The equipment contains dangerous voltages and controls potentially dangerous rotating mechanical
parts. Non-compliance with the warnings or failure to follow the instructions contained in the docu-
mentation can result in loss of life, severe personal injury or serious damage to property.
Take particular notice of the general and regional installation and safety regulations regarding work
on dangerous voltage installations (e.g. EN 50178) as well as the relevant regulations regarding the
correct use of tools and personal protective equipment (PPE).
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commission-
ing and operation of a device/system may only be performed by qualified personnel. Within the con-
text of the safety notes in this documentation, qualified persons are defined as persons who are
authorized to commission, ground and label devices, systems and circuits in accordance with estab-
lished safety practices and standards.
Disclaimer of Liability
Depending upon the firmware and software version of the Control Unit, of the Operator Panel and of
the STARTER, the masks, symbols and menus may differ. We have reviewed the contents of this publi-
cation to ensure consistency with the hardware and software described. Since variance cannot be
precluded entirely, we cannot guarantee full consistency. However, the information in this publica-
tion is reviewed regularly and any necessary corrections are included in subsequent editions.
I_DT_G120_Booklet_RZ.indd 5 04.04.2012 13:11:28
6. 6
Welcome to the SINAMICS G120 Tutorial for First Time
Users. This tutorial will help acquaint you simply, quick-
ly and comfortably with the frequency converter. We’ll
take you step by step through installation, setting
parameters and initial start-up. We recommend that you
don’t skip any chapters.
1
I_DT_G120_Booklet_RZ.indd 6 04.04.2012 13:11:28
7. 7
Converter family SINAMICS G120 08–21
1.1 Components Power Module 12
Control Unit 13
Operator Panel 2 (BOP-2/IOP) 14
1.2 Mounting and wiring Power Module 15
Control Unit 18
Operator Panels (BOP-2/IOP) 20
Operator Panels BOP-2 and IOP 22‒41
2.1 Basic functions The BOP-2 display 24
Menu structure 25
2.2 Working with BOP-2 Parameter list 27
Operating pattern 27
Function buttons 29
2.3 Quick commissioning Resetting the converter 30
Setting the control mode 31
Selecting line frequency 31
Entering motor data 32
Specifying application parameters 33
Saving and restoring data 35
2.4 Intelligent Operator Panel The device 37
Working with IOP 38
STARTER software and PC 42‒73
3.1 Mounting and preparation Creating a STARTER project 46
STARTER user interface 49
Loading converter data 50
3.2 Parameterization Configuration wizard 54
Safety Integrated 58
Start motor data identification 62
3.3 Application cases Setting setpoint specifications 65
Saving data 67
Restoring factory settings 70
Appendix Download overview 75
I_DT_G120_Booklet_RZ.indd 7 04.04.2012 13:11:28
8. 8
This chapter will introduce the low-voltage SINAMICS
G120 converter. You’ll learn about the main compo-
nents, hear about its structure and get some practice-
oriented insight about the assembly and wiring of the
frequency converter.
1
I_DT_G120_Booklet_RZ.indd 8 04.04.2012 13:11:28
10. 10
1.1 Components
The SINAMICS G120 frequency converter is modular.
It comprises of three basic components:
1 2
The Power Module supplies
voltage to the motor
The Control Unit controls and
monitors the Power Module
Converter family SINAMICS G120: Components
I_DT_G120_Booklet_RZ.indd 10 04.04.2012 13:11:35
11. 11
3 +
The Basic Operator Panel (BOP-2) and
the Intelligent Operator Panel (IOP)
are used to operate and monitor the
converter
The optional PC Connection Kit-2
can also be used to set parameters,
operate and monitor the converter;
the kit is required in order to establish
communication between a PC and the
Control Unit
Each Control Unit can be freely
combined with each Power
Module.
nOTE
I_DT_G120_Booklet_RZ.indd 11 04.04.2012 13:11:37
12. 12
1
2
3
4
5
Power Module
The device is available in several sizes. Its power range is between 0.37 kW and 250 kW.
The picture shows the PM240-2 frame size A.
Please check the rating plate
to make sure that the module
also meets your requirement
specifications.
Note
Rating plate
Power connectors
Connectors / Braking resistor
Motor connectors
PE terminals
1
2
2 5
5 4
4
3
3
Converter family SINAMICS G120: Components
I_DT_G120_Booklet_RZ.indd 12 04.04.2012 13:11:42
13. 13
1
2
3
3
1
6
4
2
5
8
8
8
7
4
5
6
7
8
Control Unit
There are various designs for the Control Units. They differ primarily in terms of the control terminal
assignments as well as in terms of different field bus interfaces. This tutorial will use the example of the
CU240E-2 Control Unit. It was developed for stand-alone operation.
An overview of the various control
unit versions and their differentia-
tion can be found in the official
SINAMICS G120 brochure at:
http://www.siemens.com/
sinamics-g120/printmaterial
Note
Rating plate
DIP switch for analog inputs
and fieldbus address
Interface for the Operator
Panel (BOP-2 or IOP)
Status LEDs
Terminals for digital and
analog inputs and outputs
USB interface for STARTER
Interface to the Power
Module
Fastening clips
I_DT_G120_Booklet_RZ.indd 13 04.04.2012 13:11:43
14. 14
Basic Operator Panel 2 (BOP-2)
The basic input and display device is used to operate and set parameters for the converter after being
connected to the Control Unit. It is operated by pressing the buttons and features a simple commission-
ing thanks to the menu prompting and the 2-line display.
Intelligent Operator Panel
The Intelligent Operator Panel manages the same functions as the BOP-2 but adds several more options.
The integrated application wizard, full graphical diagnostic overviews and plain text increase usability
substantially. It is available in various versions and can be used drive-externally for series commissioning
and on-site diagnosis.
1
3
4
1
2
3
2
6
6
5 5
4
1
1
6 6
5 5
4 4
3 3
2 2
BOP-2 IOP
Seven operating buttons
Display
Release catch
Door mounting screw recess
RS232 connector
Product rating label
Graphical display
Navigation wheel
Five operating buttons
USB connection
RS232 connector
Product rating label
Converter family SINAMICS G120: Components
I_DT_G120_Booklet_RZ.indd 14 04.04.2012 13:11:49
15. 15
Mounting of the Power Module into the switch cabinet
Please refer to the drilling pattern accompanying the Power Module for
the correct drilling centers and clearance distances above and below the
Power Module.
1.2 Mounting and wiring
Before starting assembly, check to ensure the following conditions have been met:
• All required components, tools and small parts have been prepared
• All required cables and lines have been laid in accordance with specifications
• All minimum clearances are being observed
Normally the motor and converter
are selected in such a way that
they match each other. This is also
the case in our example. However,
the data from the rating plate of
the motor are important for the
initial start-up of the converter.
Note
The 5 Safety Regulations must be strictly observed
• Disconnect
• Secure against unintentional restart
• Verify that it is free of voltage
• Ground and bypass
• Cover and shield any adjacent live parts
Example of
drilling pattern
36.5 mm (1.44)
62.3mm (2.45)
5.35
mm
(0.21)
186
mm
(7.32)
I_DT_G120_Booklet_RZ.indd 15 04.04.2012 13:11:49
16. 16
Connecting the Power Module to the motor
Depending on the operating environment, different cable length limits are required for the connection
between the Power Module and motor. Unshielded cables up to 100 m in length are possible in indus-
trial electrical networks.
The motor and Power Module are now connected.
The electrical wiring is now complete.
Wiring the Power Module
• Connect the phases and the earth conductor to the terminals U2, V2, W2 and PE
Wiring the motor
• Unscrew the cover to the terminal box on the motor (the inside cover of Siemens’ motors
illustrates the possible wiring for the Star connection and the Delta connection)
• Remove the bridge rails from the connecting block and loosen the screws
• Place the bridge rails on the terminal block and screw them into place (depending on the
type of connections required – Star or Delta, in this example a Star connection is shown)
• Insert the cables from the Power Module through the opening of the terminal box to the motor
• Connect the PE connection first
• Slide the phases in accordance to the phase assignment in the connections
• Replace the terminal cover and ensure it is secured with the four screws to the required torque
Wiring the power supply
• Connect the phases and the earth conductor to the pluggable terminal clamps L1, L2, L3 and PE
1
2
3
Converter family SINAMICS G120: Mounting and wiring
I_DT_G120_Booklet_RZ.indd 16 04.04.2012 13:11:49
17. 17
Motor lines represent interfering
transmitters. As a result, you
should use shielded cable in order
to meet the corresponding elec-
tromagnetic compatibility condi-
tions. The cable lengths that are
actually possible depend upon the
following:
‒ Operating environment
‒ Converter being used
‒ Reactors and filters used
‒ Shielded or unshielded cable
In order to meet Class A electro-
magnetic compatibility require-
ments, you need a filter and a
shielded cable (max. length: 25
meters).
The depicted example shows a
Star connection. The rating plate
provides information about the
correct circuit data: e.g. 230/400 V
∆/Y means that you are connec-
ting the motor in Y with a 400 V
network.
Note
3
1
2
2
I_DT_G120_Booklet_RZ.indd 17 04.04.2012 13:11:54
18. 18
Attaching the Control Unit
Connect the Control Unit with the fastening clips on the bottom of the Power Module and then press
the upper edge of the Control Unit against the Power Module until the locking device snaps into place.
Before wiring the control terminals, the terminal cover has to be opened.
The wiring is now complete.
Wiring the control terminals in the CU240E-2
The potentiometer:
• Attach the positive pole of the supply voltage to 1
• Attach the negative pole to 2
• Wire the output of the potentiometer arm to 3
• Close the circuit by connecting 4 with negative pole 2
On/Off, Reverse, and Reset buttons:
• Wire the button’s power supply to 9
• Attach the associated digital inputs to terminals 5, 6 and 7
• To close the circuit, connect 28 and 69 to 34
Indicator lamps:
• Connect 9 with 20 and 21 to attach the power supply for the LEDs
• Wire the Faults LED to digital output 19 and the Warning LED to digital output 22
• Connect the negative pole to terminal 28
Display for frequency output:
• Connect the positive pole to 12
• Connect the negative pole to 13
1
2
3
4
General procedure for wiring with the cage clamp mechanism
• Slide the wire into the terminal opening
• The inner clamp opens slightly and snaps the wire tightly into place
The wire is now firmly attached.
• To release the wire press a screw driver onto the lever
• Remove the wire
• Withdraw the screwdriver from the terminal
Converter family SINAMICS G120: Mounting and wiring
I_DT_G120_Booklet_RZ.indd 18 04.04.2012 13:11:55
20. 20
Mounting the Operator Panels (BOP-2 or IOP)
• Remove the cover of the RS232 connection by lifting it up and sliding it to the side
• Place the bottom edge of the IOP/BOP-2 into the lower recess of the Control Unit housing
• Push the IOP/BOP-2 toward the Control Unit until the release-catch clicks into place
1
2
2
1
Converter family SINAMICS G120: Mounting and wiring
I_DT_G120_Booklet_RZ.indd 20 04.04.2012 13:12:02
21. 21
Mounting the IOP or BOP-2 in a cabinet door
The operator panels can simply be mounted in a control cabinet door with just a few manual operations
using the optionally available door mounting kit. Degree of protection IP55 / UL type 12 is achieved
when mounting them in the control cabinet door.
Door panel
Seal
Door mounting bracket
Screws
D-type retaining screws
Mounting the IOP
Identical mounting with BOP-2
4
3
1
2
5
1
2
3
4
5
Congratulations! Your converter is now ready for operation.
After assembly is completed, the converter’s parameters must be set up, i.e., you must give the
converter the specific characteristics of the attached motor.
I_DT_G120_Booklet_RZ.indd 21 04.04.2012 13:12:03
22. 22
In this section, you will learn more about the usage of
Operator Panels to control the converter locally on-site.
You’ll learn how to use the Basic Operator Panel 2 (BOP-2)
to set up parameters for the converter and the attached
motor and how to operate the converter with the BOP-2.
Then, you will learn how to use the Intelligent Operator
Panel (IOP) to your advantage.
2
I_DT_G120_Booklet_RZ.indd 22 04.04.2012 13:12:03
24. 24
Menu bar indicates the
selected menu function
(see page 25)
Provides information about
the selected functionality or
displays the actual value
Displays the values
Operator Panels BOP-2 and IOP: Basic functions
In this tutorial, we introduce an
application that is based on “V/f
control with linear characteristic
curve”. This control method is
typically applied for conveyor
belt applications. We recom-
mend that you work through the
example we have presented here
in order to familiarize yourself
with setting up parameters for a
converter.
Note
2.1 Basic functions
The Operator Panel is the input and display instrument for controlling the converter. It is used in stand-
alone operation, i.e., locally, on the device, integrated in the cabinet door or as handheld version for
series setup (IOP).
The BOP-2 display
The BOP-2 is used to commission, diagnose (troubleshoot) and display the status of the converter. Up to
2 status values can be simultaneously and continuously monitored. It features a simple navigation using
a transparent and well-structured menu and clearly assigned operator keys.
1 2
1
2
3
3
I_DT_G120_Booklet_RZ.indd 24 04.04.2012 13:12:12
25. 25
MONITORING
The actual status of the converter/motor system is dis-
played
CONTROL
Setpoint, Jog and Reverse mode can be activated
DIAGNOSTICS
Faults and alarms can be acknowledged, history and
status is displayed
PARAMETER
Parameter values can be viewed and changed
SETUP
Basic commissioning of the converter can be per-
formed
EXTRAS
Additional functions such as saving and copying data
sets into and from the BOP-2 can be performed
1
1
4
2
5
3
6
2
3
4
5
6
Menu structure
When moving the menu bar to the following menu function, the following applies:
I_DT_G120_Booklet_RZ.indd 25 04.04.2012 13:12:12
26. 26 Operator Panels BOP-2 and IOP: Working with BOP-2
ESC key – Takes you back to the
previous screen
Up key – Change selection
Down key – Change selection
OK key – Confirm the selection
OFF key – Stops the motor in manual
mode
HAND / AUTO key – Switches the
command source between HAND and
AUTO mode
ON / RUN key – Starts the Motor in
manual mode
2.2 Working with BOP-2
The BOP-2 has got seven buttons. For setup and parameterization only the UP and DOWN, OK and ESC
buttons are relevant. The ON, OFF and HAND/AUTO keys are needed for local operation.
1
4 7
6
5
4
3
1
2
2
3
5 6 7
I_DT_G120_Booklet_RZ.indd 26 04.04.2012 13:12:12
27. 27
• Press UP to access the next parameter
• In this case, P3 appears (P means that you can change the value of this parameter)
• Press OK to edit the parameter
• Use the UP and DOWN buttons to adjust the value
• Confirm the value by pressing OK
Operating pattern
• Press ESC to enter the menu selection
• Use the UP and DOWN buttons to move the menu bar to PARAMS and press OK
• Press OK to select the Standard Level
Parameter list
To better understand the functionality of the buttons, you should be acquainted with the operating
pattern: The Basic Operator Panel gives you access to a parameter list. Stored behind the parameters are
parameter values that control the operation of the motor. However, not all the numbers are assigned.
The first parameter number that appears is displayed on the left side of the screen: r2 (r stands for read
only and means that you can only read this value but cannot change it). On the right side, the parame-
ter value of the selected number is shown.
Example
If you want to change any param-
eter using the parameter list, you
are requested to choose a filter
level (Standard or Expert). The
Standard Level limits the avail-
able parameters, thus limiting
the risk of dangerous parameters.
The Expert Level gives access to
all parameters.
Note
Example
ESC
ESC
OK
OK
OK
OK
I_DT_G120_Booklet_RZ.indd 27 04.04.2012 13:12:13
28. 28 Operator Panels BOP-2 and IOP: Working with BOP-2
Example for index parameters
• Pressing OK takes you to [00]
• UP takes you to [01], DOWN back to [00]
• Decide for an index number of your choice
• Press OK again to edit the index
• The value starts flashing
• Adjust the value by pressing UP and DOWN
• Confirm by pressing OK
Some parameters store more than one value. In this case, pressing OK does not take you directly to the
value, but to an index that is displayed in brackets [00] above the actual value.
Example
OK
OK
OK
A complete list of all parameters
can be found in the “Parameter
Manual: Control Units –
CU240E/B-2” as a download at:
http://support.automation.
siemens.com/WW/view/
en/49946755
If you want to adjust any blink-
ing/active value digit by digit
(using the UP and DOWN button
might just take too long), you
can always press the OK button
longer than two seconds. After
releasing the button, you can
change any single digit by using
the buttons OK (move to next
digit), ESC (move to previous
digit), UP (increase value), and
DOWN (decrease value).
Note
I_DT_G120_Booklet_RZ.indd 28 04.04.2012 13:12:13
29. 29
Function buttons
With the function buttons, you can actually operate the motor. The HAND/AUTO button changes the
command source between the BOP-2 (HAND) and field bus (AUTO). A hand icon appears in the screen
to indicate HAND mode is active.
• In HAND mode the ON and OFF buttons are enabled
• In AUTO mode the ON and OFF buttons are disabled
• If HAND mode is active, pressing the HAND/AUTO button will switch the converter to AUTO mode
• If AUTO mode is active, pressing the HAND/AUTO button will switch the converter to HAND mode
• Changing HAND to AUTO mode is possible while the motor is still running
Screen Icons
The BOP-2 displays a number of icons at the left-hand side of the display to indicate the actual state
of the converter.
• Command source auto / hand
• Converter status running
• JOG
• Fault / Alarms active
A detailed list of the Fault and
Alarm messages can be found in
the “Parameter Manual: Control
Units – CU240E/B-2” as a down-
load at: http://support.
automation.siemens.com/WW/
view/en/49946755
Note
JOG
I_DT_G120_Booklet_RZ.indd 29 04.04.2012 13:12:13
30. 30
Starting quick commissioning
• Press ESC to enter the menu selection
• Use UP and DOWN to move the menu bar to SETUP and press OK
• The screen will automatically display the next parameter in the commissioning sequence
Resetting the converter
• Press OK while the BOP-2 shows RESET
• Press UP or DOWN to change the value to YES
• Press OK and wait until the BUSY sign disappears
• Now all values are reset to the factory setting
Operator Panels BOP-2 and IOP: Quick commissioning
Any step of the commissioning
wizard can be skipped by press-
ing the DOWN button. Going
back one step can be done by
pressing the UP button. By con-
firming one step with OK, the
screen will automatically display
the next parameter in the com-
missioning sequence.
Note
2.3 Quick commissioning
The following descriptions show how to set up the drive using the quick commissioning wizard
integrated in the BOP-2.
Quick commissioning begins now. It will help you set all relevant parameters step by step. Parameters
that are not relevant will be skipped automatically. Thus, you adjust the factory settings of your con-
verter to the requirements of your motor.
OK
OK
ESC OK
I_DT_G120_Booklet_RZ.indd 30 04.04.2012 13:12:13
31. 31
Setting the control mode (P1300)
In our example it is assumed that your converter and the motor are new. As a result, a series of
pre
paratory steps are required, e.g. selecting the control mode. This is indicated by the parameter
number 1300. ‘V/f control with linear characteristic curve’ is defined by the factory setting.
• Press OK to modify the parameter value CTRL MOD
• The upper row shows the control mode associated to the actual parameter value below
• Choose your desired control mode value by pressing UP or DOWN
• See how the control mode name in the upper row changes accordingly
• Press OK if the desired control mode is displayed
Selecting line frequency (P100)
The next parameter sequence sets the line frequency of the region in which the motor is being used.
In our example, this is Europe.
• Press OK to modify the parameter value EUR USA
• Set 0 for Europe (50 Hz) (1 represents the US line frequency of 60 Hz)
• Confirm the value by pressing OK
• The screen will automatically display the next parameter in the commissioning sequence
The applicable line frequency
can be also found on your motor
plate (see chapter “Entering
motor data”).
Note
OK
OK
OK
OK
I_DT_G120_Booklet_RZ.indd 31 04.04.2012 13:12:13
32. 32
2.0 HP
3.55-3.55
2.05-2.05
84.5%
84.5%
86.5%
NOM.EFF
K
A
V
380 - 420
660 - 725
CL
IP55
E0807/0496382_02 003
IMB3
UNIREX-N3
40°C
Tamb
Th.Cl. 155(F)
25 kg
Design A
TEFC
MG1-12
NEMA
SF 1.15 CONT
60Hz:
Intervall: 4000hrs
IEC/EN 60034 100L
3~Mot. 1LE10011AC434AA0
6206-2ZC3
6206-2ZC3
Bearing
DE
NE 11g
15g
D-91056 Erlangen
-20°C
Y
400
460
690
V
970
970
1175
rpm
0.73
0.73
0.69
PF
3.15
3.5
2.05
A kW
Hz
50
60
50
1.5
1.5
1.5
Operator Panels BOP-2 and IOP: Quick commissioning
If you want to adjust any flash-
ing value digit by digit (using the
UP and DOWN button might just
take too long) press the OK but-
ton longer than two seconds.
After releasing the button, you
can change each single digit by
using the buttons OK (move to
next digit), ESC (move to previ-
ous digit), UP (increase value)
and DOWN (decrease value).
Note
1 2 3 4 5
1
3
2
4
5
P304 = MOT VOLT = Motor voltage
P100 = EUR USA = Standard IEC or NEMA
P305 = MOT CURR = Motor rated current
P307 = MOT POW = Motor rated power
P311 = MOT RPM = Motor rated speed
The line frequency has been set already
in the beginning of quick commissioning
(see page 31.)
Entering motor data
In the next step, the converter is adjusted to the motor. The motor data can be found on the motor’s
rating plate. Please set the values according to the plate.
• Press OK to edit the motor voltage stored under P304
• The preset motor voltage of 400 volts is displayed
• Leave the value and confirm by pressing OK
OK
OK
OK
I_DT_G120_Booklet_RZ.indd 32 04.04.2012 13:12:17
33. 33
Activating pre-defined settings (P15) e.g. for command and setpoint source
• Press OK to activate macro parameterization MAc PAr
• Macro 12 (Std ASP) is displayed, it determines DI 0 for the command source and the
potentiometer for the setpoint source
• Leave the value and confirm by pressing OK
The converter can now be turned on using digital input DI 0.
The setpoint source is specified as the potentiometer.
Motor data identification
After entering the motor data, the wizards asks to activate the motor data identification. This is recom-
mended for a live verification and optimization of the data that you have entered. The motor data iden-
tification initiates a “measurement” of the connected motor. In the process, the data previously calcu-
lated in the converter are compared to the actual motor data and adapted to one another.
Specifying application parameters
In the next step, pre-defined settings for the converter’s interfaces can be activated. This is stored in
parameter number 15 and indicated by MAc PAr for macro parameterization. For example, the converter
offers different pre-defined macros for setting the command and setpoint source.
Activating motor data identification (P1900)
• Press OK to confirm MOT ID
• Change the displayed value to 1 by pressing UP
Motor data identification does only start after the basic commissioning sequence has been completed
and the motor is switched on the first time!
OK
OK OK
I_DT_G120_Booklet_RZ.indd 33 04.04.2012 13:12:17
34. 34 Operator Panels BOP-2 and IOP: Quick commissioning
Completing quick commissioning
• Press OK while the BOP-2 shows FINISH
• Select YES and press OK again
The values are displayed in seconds. In both cases, the times indicated should not be too short, because
this might result in an alarm.
The converter is now parameterized optimally to your application and
motor specifications. Now motor data identification should be per-
formed to finalize the commissioning. This can be done by switching
on the motor. At the moment, command source is set to digital input
DI 0. Start the motor with turning on DI 0.
Minimum frequency, ramp up and ramp down time (P1080)
• Set the minimum frequency under parameter MIN RPM
• Press OK (Parameter MIN RPM)
• Change the value by pressing UP or DOWN
• Press OK to confirm
• Set the ramping-up time under parameter RAMP UP for acceleration time to maximum
frequency (P1120)
• Set the ramping-down time under parameter RAMP DWN for time until standstill (P1121)
Changing the value digit by digit
is possible by pressing the OK but-
ton longer than 2 seconds. After
releasing the button, each single
digit can be changed by using the
buttons OK (move to next digit),
ESC (move to previous digit), UP
(increase value) and DOWN
(decrease value).
Refer to the “Parameter Manual:
Control Units – CU240E/B-2” for a
description of the control modes
and their corresponding parame-
ter settings at: http://support.
automation.siemens.com/WW/
view/en/49946755
Note
OK OK
OK OK
OK OK
OK OK
I_DT_G120_Booklet_RZ.indd 34 04.04.2012 13:12:17
35. 35
The Basic Operator Panel 2 can also be used to make a variety of other
adjustments to your application. Please note that an overview of the
parameter numbers can be found in the Operating Instructions: Con-
trol Units CU240E-2.
Motor data identification
• Start the motor manually by using digital input DI 0
• The measuring process is set in motion
• When finished, the motor switches off
• BOP-2 indicates that the measured values are now being converted into data
Saving parameter sets from converter to BOP-2
• Navigate with the menu bar to the function EXTRAS
• Press OK
• Push the DOWN button until TO BOP appears
• Press OK
Copying parameter sets from BOP-2 to converter
• Navigate to the menu EXTRAS
• Press OK
• Push the DOWN button until FROM BOP appears
• Press OK
Saving and restoring data
Saving data in different location is important. The EXTRAS function allows loading parameter data from
the converter memory to the BOP-2 and vice versa.
The BOP-2 can be mounted or
removed at any time. The device
is not necessary for ongoing
operation.
Note
OK
OK
OK
OK
I_DT_G120_Booklet_RZ.indd 35 04.04.2012 13:12:17
36. 36 Operator Panels BOP-2 and IOP: Intelligent Operator Panel
2.4 Intelligent Operator Panel
With the Intelligent Operator Panel, you can set the inverter parameters, put the inverter into operation,
monitor the ongoing operation of the motor, and get valuable information about faults and alarms. All
these functions can be accessed without expert knowledge. The main advantages are as follows:
Fast commissioning without expert knowledge
• Simple commissioning of standard applications using application-specific assistants, no
knowledge of parameter structure necessary
• User customized parameter lists with reduced parameter sets
• Simple local commissioning using the handheld version
• Fast multiple commissioning with clone function
• Commissioning without documentation by using the integrated help function
Minimization of maintenance time
• Diagnosis with clear text display, without documentation usable on site
• Simple update of languages, application assistants and firmware using the
integrated USB connection
• Integrated clear text help function to read and resolve fault messages and reasons locally
High usability, intuitive handling
• Direct, manual control of the drive – simple switching from local to remote operation
• Intuitive menu navigation using wheel-click interface
• Graphical display for i.e. status values in vertical-bar charts (for example pressure or flow rate)
• Status display with freely selectable units – display of real, physical values
Flexible usage
• Available for direct control unit mounting, for door mounting or as handheld version
(depending on frequency converter type)
• Simple and fast mechanical and electrical door mounting
• Handheld usable for a large variety of frequency converters
• 5 integrated languages
I_DT_G120_Booklet_RZ.indd 36 04.04.2012 13:12:17
37. 37
1 2 3
The device
The IOP is a menu-driven device. Its functionality is structured by three options:
1
2
3
The display
All necessary information is user-friendly displayed in plain text or icons. The displayed icons are
shown at the top right-hand edge of the display. They indicate various states of the converter.
• Command source auto / hand
• Inverter status ready / running
• Fault
• Alarm pending
• Battery condition Fully Charged / Discharged
[Wizards] Assists you to set up standard
applications
[Control] Allows you to change setpoint
value, turning direction activates the
jog function in real-time
[Menu] Gives you access to all possible
functionalities
I_DT_G120_Booklet_RZ.indd 37 04.04.2012 13:12:18
38. 38
Working with IOP
The IOP is operated mainly by using the push-wheel. The five additional buttons make it possible to
display certain values or to switch between manual and auto mode. The buttons are called: ON key,
OFF key, ESC key, Info key and HAND/AUTO key.
Turning changes the selection
Pressing confirms the selection
Starts the motor in manual
mode
Stops the motor in manual
mode
Takes you back to the previous
screen
Displays additional
information
Switches the command source
between HAND and AUTO
mode
The HAND/AUTO function works
identically to the one imple-
mented in the BOP-2. After start-
ing the motor with the ON but-
ton, you can change the setpoint
speed by navigating to CON-
TROL/SETPOINT and turning the
wheel (right to increase speed,
left to decrease speed).
Note
1
1
2
2
3 6
4 5
3
4
5
6
Operator Panels BOP-2 and IOP: Intelligent Operator Panel
I_DT_G120_Booklet_RZ.indd 38 04.04.2012 13:12:18
39. 39
On the top of the screen, you
can see numbers that indicate
the present step of the wizard
that you are in. 2/15 for example
means that you are in step 2 of
15.
Note
Example: Basic commissioning
• Use the wheel to highlight the word WIZARDS
• Confirm by pressing OK
• Navigate to BASIC COMMISSIONING by turning the wheel
• Confirm by pressing OK
The wizards
There are several wizards which allow you to set up various functions and commission the converter.
They navigate you interactively through the parameterization of standard applications. The wizards are
accessed from the wizard menu, at the bottom-left of the status screen.
Now the wizard will guide you step by step through the basic commissioning process by presenting a
number of screens where you can choose the necessary options and values. At the conclusion of the
basic commissioning process, the data can be saved to the converters memory, and calculation of motor
and control data is started.
• Always use the wheel to select an option and press OK to confirm
• Press ESC to move back one step
• Press INFO to read context-sensitive help information
Wizards Basic Commissioning
OK OK
OK OK
I_DT_G120_Booklet_RZ.indd 39 04.04.2012 13:12:18
40. 40
Accessing diagnostics
If you want to find out which input and output devices are connected to the converter, simply navigate
to the diagnostics menu and select the I/O STATUS. This option displays a list of the digital and analog
inputs and outputs of the converter. In addition, you can monitor their current status. This is an infor-
mation screen and cannot be changed.
Using the button INFO, always
gives you more in-depth infor-
mation on the presently high-
lighted parameter, step or
feature.
Note
Reading the I/O status
• Use the wheel to highlight the word MENU
• Confirm by pressing OK
• Select DIAGNOSTICS
• Confirm by pressing OK
• Choose I/O STATUS
• Confirm by pressing OK
• Choose STATUS DIGITAL INPUTS
• Confirm by pressing OK
You can now see a clearly arranged overview of all connected I/O including their status.
OK OK
OK OK
OK OK
OK OK
Diagnostics
I/O Status
Menu
Status Digital Inputs
Operator Panels BOP-2 and IOP: Intelligent Operator Panel
I_DT_G120_Booklet_RZ.indd 40 04.04.2012 13:12:18
41. 41
If you want to find out about
previous faults and alarms,
please navigate back one level
and select “History”. This will dis-
play a list of all previous faults
and alarms including the time
they occurred.
Note
Getting information on active faults
• Use the wheel to highlight the word MENU
• Confirm by pressing OK
• Choose DIAGNOSTICS
• Confirm by pressing OK
• Select ACTIVE FAULTS/ALARMS
Now, all active fault messages that have not yet been acknowledged are displayed.
To get further information, you can highlight each one and press INFO.
You now know how to use the Operator Panels to set the parameters on your converter and start it
up. A further possibility is setting up the parameters using your PC or a SIMATIC programming device.
This method is clearer and more convenient, but requires somewhat more preparation time.
OK OK
OK
OK OK
OK
Menu Diagnostics
Active Faults/Alarms
I_DT_G120_Booklet_RZ.indd 41 04.04.2012 13:12:18
42. 42
In the next step, you will learn how to connect your PC or
PG to the converter and how to set parameters with the
STARTER software. With STARTER, you can also easily
activate the Safety Integrated functions of the drive.
3
I_DT_G120_Booklet_RZ.indd 42 04.04.2012 13:12:18
44. 44 STARTER software and PC: Mounting and preparation
3.1 Mounting and preparation
The optional PC Connection Kit 2 is required to set up the parameters using a PC.
The kit consists of two components.
1 2
Connecting cable STARTER software on DVD
I_DT_G120_Booklet_RZ.indd 44 04.04.2012 13:12:26
45. 45
Hardware preparation
• Place the STARTER DVD into your DVD drive
• Install the STARTER software by following the setup wizard
• Connect the USB cable to the Control Unit
• Connect the other end to the USB interface of your PC
The STARTER is also available as
a download at: http://support.
automation.siemens.com/WW/
view/en/26233208
Note
You must install the USB driver if you are connecting the converter and PC together for the first time.
Windows 7 automatically installs the driver; for older Windows versions, you must confirm the auto-
matic installation.
I_DT_G120_Booklet_RZ.indd 45 04.04.2012 13:12:27
46. 46
Creating a STARTER project
After installation is complete, switch on the converter’s power supply and start the program. The project
wizard opens automatically. The wizard will help you create your first project.
Select “Find drive units online”
Give the project a name and click “Continue”
1
2
STARTER software and PC: Mounting and preparation
1 2
I_DT_G120_Booklet_RZ.indd 46 04.04.2012 13:12:27
47. 47
Check that “DEVICE” is set as Access point. If not, choose “Access point ...” and set “DEVICE” in the dialog box “Set Access
Point for Accessible Nodes”. Check that “S7USB” is set as interface. If not, choose “PG/PC ...”.
Open the drop-down menu “Access Point of the Application”
Choose the command “DEVICE (STARTER – SCOUT) -- S7USB”
In “Interface Parameter Assignment Used” select “S7USB”
Close with OK
3
4
5
6
6
7
3
4
5
7
I_DT_G120_Booklet_RZ.indd 47 04.04.2012 13:12:34
48. 48
The identified converter is displayed
Add the converter to your project with “Insert drive units”
Close the project wizard with “Complete”
10
10
8
9
STARTER software and PC: Mounting and preparation
The converter is now integrated into the project tree and the parameters can be set up using the
STARTER software.
8
9
I_DT_G120_Booklet_RZ.indd 48 04.04.2012 13:12:40
49. 49
STARTER user interface
Project tree
Program menu
Toolbar with special features
Icon “Connect to selected target devices”
Connection mode
Work area
1
1
4
2
2
5
5
6
3
3
4
6
I_DT_G120_Booklet_RZ.indd 49 04.04.2012 13:12:41
50. 50 STARTER software and PC: Mounting and preparation
Loading converter data
Before you can load the current converter’s data into your project, an online connection between the
PC and the converter has to be established.
Click the icon “Connect to selected target devices”
Set the access point to “DEVICE” and place a checkmark next to converter name
Click “Load HW configuration to PG”
1
2
3
1
2
3
I_DT_G120_Booklet_RZ.indd 50 04.04.2012 13:12:46
51. 51
Now the converter data is loaded into the project and an online connection between PC and converter
is established.
The blue highlighted “Offline mode” changes to the yellow highlighted “Online mode”
The workbench area opens
4
5
Workbench area
The area provides additional information such as alarms, the target system output and the
diagnostics overview. It also stores additional operating features.
4
5
I_DT_G120_Booklet_RZ.indd 51 04.04.2012 13:12:46
52. 52 STARTER software and PC: Parameterization
3.2 Parameterization
You can now begin to parameterize your converter.
Double-click on the converter icon in the project tree
Click on “Load CPU / drive unit to PG”
1
2
1
2
2
I_DT_G120_Booklet_RZ.indd 52 04.04.2012 13:12:50
53. 53
Double-click “Configuration”
Click “Wizard ...” in the work area and let the wizard guide you
3
3
4
We recommend parameterizing our
example using the online mode.
Note
4
I_DT_G120_Booklet_RZ.indd 53 04.04.2012 13:12:52
54. 54
Configuration wizard
The configuration wizard guides you step by step through the following parameters:
• Control structure
• Defaults of the setpoint source and the command source
• Drive setting
• Motor
• Motor data
• Drive functions
• Important parameters
• Calculation of the motor data
• Summary
By clicking “Next” you get to the next configuration step.
STARTER software and PC: Parameterization
1 2
I_DT_G120_Booklet_RZ.indd 54 04.04.2012 13:12:54
55. 55
Start by setting the control structure
Define the command and setpoint source
Select the motor type
Input motor data corresponding to the rating plate
1
2
4
3
For non-Siemens motors, please
use the motor rating plate to
input the motor data.
Note
3 4
I_DT_G120_Booklet_RZ.indd 55 04.04.2012 13:12:57
56. 56
Select “Identify motor data at standstill” for motor data identification
Enter maximum current
Enter minimum and maximum speed
Enter ramp-up, ramp-down time and OFF3 ramp-down time emergency shut-off
5
6
7
8
STARTER software and PC: Parameterization
5
6
7
8
I_DT_G120_Booklet_RZ.indd 56 04.04.2012 13:13:00
57. 57
After clicking “Next”, the calculating of the motor data starts. This concludes the parameterization with
the configuration wizard. You will now receive a summary of all parameter values input. The summary
can be inserted into a text file by pressing the “Copy text to clipboard” button. Finally select “Copy RAM
to ROM” to store the parameterization in the converters ROM memory and close the window by clicking
“Finish”.
I_DT_G120_Booklet_RZ.indd 57 04.04.2012 13:13:07
58. 58
Safety Integrated
If your converter is used in a safety related environment, we strongly recommend performing Safety
Integrated engineering using the STARTER. STARTER guides you clearly and easily through the process.
Thus, the risk of wrong parameterization is reduced to a minimum.
All control units CU240E-2 come with the Safety Integrated function STO (Safe Torque Off). STO can be
used when the motor can decelerate to a standstill within a short period of time. Activating the STO
function, immediately ensures that the motor cannot supply any further torque-generating energy.
Advantages for the user:
• No wearing parts thanks to electronic shutdown
• Converter remains connected to the supply, it always supports full diagnostics capability
• Password protected, no manipulation of the function possible
STARTER software and PC: Parameterization
The CU240E-2_F and CU240E-2_
DP-F Control Units have several
Safety functions integrated.
In this case, no encoder is needed.
Detailed information about
SINAMICS Safety Integrated are
available at: www.siemens.com/
safety-integrated
Note
STO
t
v
I_DT_G120_Booklet_RZ.indd 58 04.04.2012 13:13:08
59. 59
Activating Safety Integrated
Browse to “Safety Integrated” in the project tree
Select “Change settings”
Choose ”STO via terminal” from the drop-down menu
1
1
2
3
2
3
Did you know that extended
SINAMICS Safety Integrated
functions can be used without
the need of an encoder at the
motor? This worldwide unique
feature saves installation and
engineering time, reduces sys-
tem costs and saves space. For
further instructions consult the
Safety functional manual
SINAMICS G120 and SINAMICS
G120C using the Siemens Prod-
uct Information System (Prodis)
at: http://support.automation.
siemens.com/WW/view/
en/50736819
Note
3
I_DT_G120_Booklet_RZ.indd 59 04.04.2012 13:13:10
60. 60
If your converter is connected to a controller, set the output signal to “STO active” in the corresponding drop-down menu
Click on “extended settings” for further adjustments
Follow the STARTER instructions
5
4
6
STARTER software and PC: Parameterization
5
6
4
I_DT_G120_Booklet_RZ.indd 60 04.04.2012 13:13:12
61. 61
Now your first Safety channel is set. For the second channel just copy the parameters. Clicking “Activate
settings” concludes the safety engineering. In the workbench area click on “Alarms” and press the
“Acknowledge” button to activate the actually safety functions.
I_DT_G120_Booklet_RZ.indd 61 04.04.2012 13:13:15
62. 62
Start motor data identification
Open the “Commissioning” entry in the project tree
Double-click “Control panel” in the project tree
Click on “Assume control priority!” in the workbench area
A setup window for command transfer opens, accept the displayed values and safety instructions
The pending motor data identifi-
cation is indicated by the mes-
sage “A7991” in the alarm tab.
The message tells you that motor
data identification will be per-
formed after switching the
motor on.
Note
STARTER software and PC: Parameterization
1
2
3
4
1
3
4
4
2
I_DT_G120_Booklet_RZ.indd 62 04.04.2012 13:13:18
63. 63
Place a checkmark next to “Enables” in the workbench area
Now the STARTER software has control authority for the attached motor.
Click the green button to start the motor
5
6
5
6
I_DT_G120_Booklet_RZ.indd 63 04.04.2012 13:13:27
64. 64
Motor data identification is processed. Parameter setup has been successfully completed
when Alarm 7991 has disappeared.
STARTER software and PC: Parameterization
I_DT_G120_Booklet_RZ.indd 64 04.04.2012 13:13:29
65. 65
3.3 Application cases
Before returning control authority from the STARTER software to the terminal, you should try controlling
the motor from the PC.
Setting setpoint specifications
Input 1.500 rpm in the “setpoint specification” box
Click the green button to start the motor
See how the motor runs with 1.500 rpm
1
2
3
1 3
2
I_DT_G120_Booklet_RZ.indd 65 04.04.2012 13:13:42
66. 66
Adjust the speed with the slider
Click the red button to stop the motor
Conclude the process by clicking “Give up control priority!”
All functions from the displayed control area in the STARTER will be deactivated. The control authority
has been returned to the terminal.
4
5
6
STARTER software and PC: Application cases
4
5
6
I_DT_G120_Booklet_RZ.indd 66 04.04.2012 13:13:54
67. 67
Saving data
A power outage may cause the loss of the parameter settings. As a result, STARTER offers
various possibilities for protecting your parameter settings.
Double-click the “Drive navigator” in the project tree
Select “Commissioning” in the work area
1
2
1
2
I_DT_G120_Booklet_RZ.indd 67 04.04.2012 13:13:57
68. 68
Select “Save data in drive (RAM to ROM)” to store the parameter settings in the converter’s EEPROM memory
STARTER software and PC: Application cases
3
3
I_DT_G120_Booklet_RZ.indd 68 04.04.2012 13:14:06
69. 69
Because you have worked in online mode, no data whatsoever have been stored in your project.
Click “Save data to project” to save the parameter setting in your project
Now you could disconnect the online connection to the converter by clicking the
“Disconnect from target system” icon. In our example, please continue to remain online to restore the
converter to its factory settings.
4
4
I_DT_G120_Booklet_RZ.indd 69 04.04.2012 13:14:08
70. 70 STARTER software and PC: Application cases
Restoring factory settings
Resetting your converter to factory settings might be helpful if you have experienced any problems
during parameterization.
Double-click the “Drive navigator”
Select “Commissioning”
1
2
1
2
I_DT_G120_Booklet_RZ.indd 70 04.04.2012 13:14:10
71. 71
Click “Factory settings”
The security query that is now displayed lets you know that all settings you have made will be reset.
Using the checkbox query, you will have the opportunity to save your settings to the converter’s ROM
memory beforehand.
3
3
I_DT_G120_Booklet_RZ.indd 71 04.04.2012 13:14:12
72. 72 STARTER software and PC: Application cases
Click “OK” to reset all converter settings to the factory setting
4
4
I_DT_G120_Booklet_RZ.indd 72 04.04.2012 13:14:20
73. 73
After reset click “Disconnect from target system”
You now know how to use STARTER to quickly and clearly insert your converter into a project, set up its
parameters, and put it into operation. Please make sure that you always remember to save the parame-
ter data to the converter and in the software before exiting a project.
5
5
I_DT_G120_Booklet_RZ.indd 73 04.04.2012 13:14:28
74. 74
Congratulations!
You have mastered the SINAMICS G120 Training
Booklet.
Thank you for your time and efforts. We hope that this
tutorial has addressed all the questions you had and was
useful to you. More detailed information can be found
online.
I_DT_G120_Booklet_RZ.indd 74 04.04.2012 13:14:30
75. 75
Download overview
Overview of the various control unit versions
http://www.siemens.com/sinamics-g120/printmaterial
SINAMICS G120 brochure
Safety Integrated Function Manual
http://support.automation.siemens.com/WW/view/en/50736819
STARTER software
http://support.automation.siemens.com/WW/view/en/26233208
Additional information on parameters
http://support.automation.siemens.com/WW/view/en/49946755
“Parameter Manual: Control Units – CU240B/E-2”
Detailed information about SINAMICS G120
http://support.automation.siemens.com/WW/view/en/50815575
“Operating Instructions: SINAMICS G120 Inverter with CU240B-2 and CU240E-Control Units”
I_DT_G120_Booklet_RZ.indd 75 04.04.2012 13:14:32