This document discusses signage types and installation procedures for a project. It outlines 13 types of dynamic information signage, 9 types each of primary and secondary signage, integrated signage, door signs, staff signs, VIP signage, outdoor signage, and traffic wayfinding signage. It also provides examples of signage categories, colors and graphics, ceiling mounting, inspection procedures, and reference drawings and documents. The goal is to ensure uniform signage that meets specifications and is installed properly with no defects or rework needed.

1. DMIA

2. Introduction
Signs are any kind of visual graphics created to display information to a particular
audience. This is typically manifested in the form of way finding information.
The main purpose of signs is to communicate, to convey information such
that the receiver may make cognitive decisions based on the information provided.
In general, signs may be classified according to the following functions:
• Information: signs conveying information about services and facilities, such as
maps, directories, or instructional signs.
• Direction: signs showing the location of services, facilities, functional spaces
and key areas, such as sign posts or directional arrows.
• Identification: signs indicating services and facilities, such as room names and
numbers, restroom signs, or floor designations.
• Safety and Regulatory: signs giving warning or safety instructions, such
as warning signs, traffic signs, exit signs, or signs conveying rules and
regulations.

3. Signage Categories
WALL MOUNTED : Backlit Dynamic Information Signage System
CEILING MOUNTED: Backlit Primary Signage
POST MOUNTED : Backlit Secondary Signage
GANTRY : Integrated Signage (In glass partitions and above elevator doors)
SUPER GRAPHICS : Door Signs, Staff Signs, VIP Signage, Outdoor Signage,
Traffic Wayfinding for Parking Area,
Traffic Wayfinding for Access Roads,
Staff Wayfinding for Access Roads,
Dynamic Advertisement Signage,
IPTV Cable Television and Graphics

4. Types of Signages
All signs shall be uniform in appearance. For an overview of the signage types,
please see sign code for the schedule of all sign types and their appropriate drawing
number in both Interim and Detail Design.
Dynamic Information Signage System : Thirteen different types. The Dynamic Signs can be either ceiling or wall mounted unless
otherwise noted.
• M1 - Backlit Illuminated Dynamic Sign
• M2 - Backlit Illuminated Dynamic Sign
• M3 - Backlit Dynamic Information Pylon
• M4 - Backlit Dynamic Sign
• M5 - Backlit Dynamic Sign
• M6 - Backlit Dynamic Sign
• M7 - Backlit Dynamic Sign
• M8 - Backlit Dynamic Sign
• M9 - Backlit Dynamic Sign:
• MA – Backlit Dynamic sign: To be integrated in the wall
• MB - Backlit Dynamic Sign
• MC - Backlit Dynamic Sign: To be canopy mounted
• MT – Backlit interactive Sign: Integrated into Information Counter

5. Primary Signage. Direction and information signs.: Nine (9)different types. The Primary Signs can be either ceiling or wall
mounted unless otherwise noted. Wall mounted versions are mostly integrated into glass partitions or walls above e.g.. elevator doors.
• P1 - Backlit Primary Sign.
• P2 - Backlit Primary Sign
• P3 - Backlit Primary Sign
• P4 - Backlit Primary Sign
• P5 - Backlit Primary Sign
• P6 - Backlit Primary Sign.
• P7 - Backlit Primary Sign
• P8 - Backlit Primary Sign: In the bus shelters a version with a dynamic LED sign instead of pictogram shall be used.
• P9 - Backlit Primary Signs. To be wall (blade) mounted.
Secondary Signage. Direction and Information signs.: Nine (9)different types. The Secondary Signs can be either ceiling or wall
mounted unless other wise noted. Wall mounted versions are mostly integrated into glass partitions or walls above e.g.. elevator doors.
• S1 - Backlit Secondary Sign
• S2 - Backlit Secondary Signs
• S3 - Backlit Secondary Signs
• S4 - Backlit Secondary Signs
• S5 - Backlit Secondary Signs
• S6 - Backlit Secondary Signs
• S7 - Backlit Secondary Signs
• S8 - Backlit Secondary Signs
• S9 - Backlit Secondary Signs

6. Integrated Signage in glass partitions: Above elevator doors and official counters.
• G1 –Integrated sign for use in glass partitions, either single or double sided.
• G2 –As G1, only for integration above elevator doors and counters. Single sided only
Door signs.: Both for use as secondary and statutory signage, non-illuminated based on a modular system and wall mounted.
• D1 – Door sign for large pictogram
• D2 – Door sign for wayfinding use.
• D3 – Door sign for location use
• D4 – Door sign for location use
• D5 – Door sign for small pictogram
• D6 – Door sign for room use,
• D7 – Door sign for room use
• D8 - Door Sign is backlit and to be wall or blade mounted
Staff signs..: For use mainly in non-passenger areas, but can also be used on staff only doors in passenger areas. Signs are non-lluminated
based on a modular system and wall mounted.
• W1 - Staff Signs
• W2 - Staff Signs
• W3 - Door sign for location use
• W4 - Door sign for small pictogram.
• W5 – Door sign for room use, 1 line.
• W6 – Office Building directory

7. VIP Signage: Elegant signage for VIP Areas, made of polished and brushed stainless steel, using single elements (letters, symbols,
pictograms) and signage panels with patterns engraved.
Outdoor signage: Four different types. Information pylons for outdoor passenger use.
• E1 - Backlit Outdoor Pylons, to be mounted on a base column made of stainless steel.
• E2 - Backlit Outdoor Signs, to be ceiling or floor mounted.
• E3 - Backlit Dynamic Outdoor Sign, to be wall mounted or integrated into the entrance above the doors.
• E4 - Backlit Outdoor Sign, to be wall mounted or integrated into the entrance above the doors
Traffic Wayfinding signage for the Parking area: Nine different types. Illuminated Information pylons, hanging signs, ‘Bus stop’
type signs as well as low non-illuminated directional.
• T1 - Backlit Traffic Wayfinding Pylon for Parking Area identification use
• T2 – Backlit Traffic Wayfinding Pylon for directional information
• T3 - Backlit Traffic Wayfinding Pylon for directional information
• T4 – Non-illuminated Traffic Sign for directional use
• T5 – Non-illuminated Row Sign for wayfinding use
• T6 – Backlit Bus stop sign, mounted on a base column of stainless steel.
• T7 - Backlit Lane Sign for identification of lane use, mounted on a base column of stainless steel
• T8 – Non-illuminated directional sign, mounted on a gantry.
• T9 – Non-illuminated Exit sign or row number sign, to be mounted on walls, columns or on shading structure

8. Examples for Types

9. NORTH PIER: 531 SIGNS
FORCOURT
NORTH: 538 SIGNS
WEST PIER: 454 SIGNS
Total Number of Signagers
DMIA
PTB: 2907 SIGNS
FORCOURT SOUTH:
511 SIGNS
TRAFFIC
CONCOURCE: 191
SIGNS
SOUTH PIER: 576
SIGNS

10. • Graphics are text and pictograms either cut in foil or printed directly on the lacquered aluminum panel.
In both cases editable graphic vector files shall be produced by the Contractor based on the graphic
manual. An alternative may be to cut the graphics by computer controlled equipment, in colored foil. This
solution may be more resistant to the weather conditions the signage is going to be used in.
• For Non-illuminated Signage, graphics are text and pictograms either cut in foil or printed directly on the
lacquered aluminum panel.
Sign Graphic and Color System
• Color: All visible cabinet surfaces shall be coated with polyester powder coating ensuring an even, smooth
and full covering semi gloss surface, semi gloss defined as approximately 60% reflection.
A lifetime of ten (10) years is required.
O:SignagesDrawings and Key Plans
O:SignagesITP-MST-Spec and ITT
.

11. Examples for Color and Graphics

12. Brackets and Installation
• All products shall be new and un-used, and shall be of manufacturer's current and standard production.
• Place the brackets in position and weld brackets to the structure as per the shop drawings .
• All site welding works on brackets will be carried out using a qualified welding procedure specification (WPS)
& qualified welders.
• Fix the brackets to the Wall with correct Bolts,nuts; fishers etc.
• Fix the signage structure to the brackets with correct bolts.

13. Ceiling Mounting Samples

14. Any anchor fails to meet any of the below acceptance criteria shall be
rejected:
- Drill bit diameter shall be equaled to diameter of sleeve
- No existing reinforcement/services in the base material shall be damaged during drilling.
- Drill-holes shall be thoroughly cleaned before inserting
.
- Check each installed anchor visually.
- Reject all anchors that are over-torque.
Inspection Procedure for Anchor Installation
- Calibrated torque wrench shall be used to apply the required torque.
DMIA

15. High performance anchor (W-FAZ/S & W-FAZ/A4) is a torque-controlled expansion
anchor. The geometrically optimized expansion sleeve of W-FAZ allows better
performance. It consists of a conical bolt, expansion sleeve, hexagonal nut and washer.

17. DMIA
Engineer comments

18. Distortion due to welding
Damages at corners
Damages while fixing
DMIA

19. Damages on back corners
Improper shades

20. Approved samples

23. ITP: Inspection Test Plan

24. ITP:
SE-TAS-03AR-ITP-0003- Rev.3
ITP,MST,Spec and ITT of Signages
DMIA
MST:
SE-TAS-03AR-MST-0003- Rev.3
ITT (Invitation To Tender):
SE-000-I-11901- Rev.3
ISSUED DATE:
15.06.2009
SPEC:SE-BEB-03EG-SPC-1040

25. Method Statement
Specifications
Inspection Test Plan (ITP)
Approved IFC Drawings
Quality Procedures
D E S K S T U D Y
MST Procedure
Specification requirement s
Work as per Control Sample and Mock up
Follow up ITP Activities
Previous approved and rejected Activities
Observations
SITE VISIT
FINAL ACCEPTANCE
Work as per MST and Specification
As per Approved IFC drawings
Documents Verifications
Collecting documents with reference to ITP
Preparation of ITR cover pages
Aconex
Submission to
Hill International
Result &
Repeat
Advantages of the cycle:
ZERO REWORK
ZERO QUALITY ISSUES
ZERO REJECTIONS
Inspection Process
DMAI

26. Reference Drawings and Documents of Signages
O:SignagesITP-MST-Spec and ITT
O:SignagesDrawings and Key Plans : All sign type drawings,
section , Elevation, Key plans and approved Mockup drawing.
O:SignagesDetails and references : Sign code with reference
drawing numbers and location details of signs.
O:SignagesPrevious Engineer comments and approved mockup
images
O:SignagesPresentation
DMIA