This quick installation guide provides instructions for setting up the EnGenius ENS1200 access point. It describes unpacking the contents of the package and lists the minimum system requirements. It then provides step-by-step instructions for connecting the ENS1200 via Ethernet cable to a PoE injector connected to a computer, and accessing the ENS1200's web interface using the default IP and login credentials. Finally, it briefly outlines how to configure the operating mode and how to wall mount or pole mount the ENS1200.

1. Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wifiabc.com
Disclaimer: Information may be subject to changes without prior notification. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENS1200
Package content
Unpack the box and verify the content:
- ENS1200
- PoE injector
- Power adapter
- Quick Start Guide
- Wall mount screw set
- 2* Pole mounting strap
Minimum requirements
- Broadband Internet Service (cable or DSL modem)
- Internet browser (Internet Explorer, Safari, Firefox, Chrome)
Connecting the ENS1200
1. Remove the rear bottom panel.
2. Connect one end of the Ethernet cable into the LAN(PoE) port of the access
point and the other end to the PoE Ethernet port on the PoE injector.
3. Connect the power adapter to the DC-IN port of the ENS1200 and plug the
other end into an electrical outlet.
4. Connect the second Ethernet cable into the LAN port of the PoE injector and
the other end to the Ethernet port on the computer.
5. Place the panel removed from step 1 back into the device.
Note: The ENS1200 should ONLY be powered via Ethernet cable connected to
the included PoE Injector.
Computer setup
1. After ensuring the EnGenius device is powered on and plugged in, ensure
that your computer is on.
2. For the next steps, refer to your operating system user manual.
3. Once your computer is on, ensure that your TCP/IP is set to ‘ON’ or
‘ENABLED’. In the control panel, double click network connections and then
double click on the connection of your Network Interface Card (NIC). Select
Internet Protocal (TCP/IP) and then click on the properties button.
4. If your PC is already on a computer network, ensure that you have set it to a
Static IP adress on the interface (or Ethernet card that will use the ENS1200).
Set it as 192.168.1.21 and set the Subnet Mask address as
255.255.255.0. Select ‘Use the following IP address’-radio button. Once the
computer has been prepared, proceed to setting up the ENS1200.

2. Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wifiabc.com
Disclaimer: Information may be subject to changes without prior notification. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENS1200
ENS1200 setup
1. To configure the ENS1200, open a web browser (example: Microsoft Internet
Explorer, Mozilla Firefox, Google Chrome, etc.)
2. In the adress bar of the web browser, enter: 192.168.1.1 (the default IP
address of the ENS1200) and hit ENTER.
3. A login screen will appear. By default, the username of the ENS1200 is
admin and the password is admin. Enter the current username and password
of the ENS1200 and then click ‘Login’. Refer to the ENS1200 user manual on
how to change the username and password.
4. After clicking ‘Login’ with the correct username an password, the ENS1200
main menu will appear. If you are successful, proceed to setting up the wireless
connection.
Switching between operating modes
This device can operate in the following modes: Access point, Client bridge,
WDS AP, WDS bridge, WDS station and Client router.
A. Click on the ‘operation mode’ link under the system navigation drop-down
menu.
B. Operating mode: Select an operating mode from the list (Access point, Client
bridge, WDS AP, WDS bridge, WDS station or Client router) and then click on
the ‘Apply’ button.
C. All basic setup is completed. Note: The wireless connection is not secure. To
setup security on the ENS1200, refer to the ENS1200 user manual.

3. Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wifiabc.com
Disclaimer: Information may be subject to changes without prior notification. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENS1200
ENS1200 Wall mounting
A. Attach the location sticker to the desired location on the wall and use a 6mm
drill bit to drill the two holes.
B. Insert the screw anchors into the 6mm holes then insert the screws and tighten.
C. Align the ENS1200 over the keyhole mounting slots and insert both screw
heads into each keyhole slot. Then slide the ENS1200 downward until it’s firmly
hooked in place.

4. Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wifiabc.com
Disclaimer: Information may be subject to changes without prior notification. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENS1200
ENS1200 Pole mounting
A. Use a flathead screwdriver to unfasten the screw on the pole mounting ring
and thread it through the middle tab on the rear of the ENS1200.
B. Mount the ENS1200 onto the pole by wrapping the ring around the pole
and fastening the screw.