Question 1.1. (TCO 3) This network appears to be working most of the time but lately it becomes slower and slower as new end devices and applications come online. What is the characteristic that is violated? (Points : 2) Security Availability Reliability Manageability Scalability Pool 2 – 5:1; 2 points; address TCO 3 Type: MCQuestion 2.2. (TCO 3) Routers use the routing table to _____. (Points : 2) select the best path toward the destination encapsulate layer 3 packets before they are sent to the egress interface determine the way of reaching the host on the ingress interface exchange network reachability information with each other C and D Type: MCQuestion 3.3. (TCO 3) What happens next if a router determines that an incoming packet has a destination of a directly connected network? (Points : 2) Check the ARP cache and forward packet to local host. Check the routing table for lowest cost path. Drop the packet and send a control message to the source address. Encapsulate the packet into a destination IP address before forwarding. Forward the packet to the next hop. Type: MCQuestion 4.4. (TCO 3) The arrangement of the cables, network devices, and end systems in a network is called its _____. (Points : 2) logical topology logical network overlay physical topology configuration topology None of the above Type: MCQuestion 5.5. (TCO 3) Being able to use a single physical router interface to route traffic between multiple VLANs on a network is called _____. (Points : 2) hub and spoke router sub-interface VLAN routing composite VLAN routing trunk-safe router router-on-a-stick Type: MCQuestion 6.6. (TCO 3) What is a disadvantage of traditional routing? (Points : 2) Does not support mutli-hop routing Can create layer-two loops Transport too many VLAN-tagged packets Can create layer 3 routing loops All of the above Type: MCQuestion 7.7. (TCO 3) The command used on a Cisco Catalyst 2960 switch to change the switched database manager (SDM) template is _____. (Points : 2) sdm change sdm use sdm prefer sdm enable None of the above Pool 9 – 3:1; 2 points; address TCO 3 Type: MCQuestion 8.8. (TCO 3) Which of the following is the proper format for assigning an IPv4 address to the interface on a Cisco router? @ See Chapter 4, page 175. (Points : 2) ip address ip-address subnet-mask ip address ip-address assign address ip-address subnet-mask interface ip-address None of the above Type: MCQuestion 9.9. (TCO 3) Which command would you use to troubleshoot a routing problem between a router and a switch? (Points : 2) show interface ip brief debug ip route Debug interface ip show ip protocols show ip route Question 1.1. (TCO 3) This network appears to be working most of the time but lately it becomes slower and slower as new end devices and applications come online. What is the characteristic that is violated? (Points : 2) Security Availability Reliability Manageability Scalability Pool 2 – 5:1; 2 points; address TCO 3 Type: MCQuestion 2.2. (TCO 3) Routers use the r.

1. Question 1.1. (TCO 3) This network appears to be working most of the time but lately it
becomes slower and slower as new end devices and applications come online. What is the
characteristic that is violated? (Points : 2) Security
Availability
Reliability
Manageability
Scalability
Pool 2 – 5:1; 2 points; address TCO 3
Type: MCQuestion 2.2. (TCO 3) Routers use the routing table to _____. (Points : 2) select
the best path toward the destination
encapsulate layer 3 packets before they are sent to the egress interface
determine the way of reaching the host on the ingress interface
exchange network reachability information with each other
C and D
Type: MCQuestion 3.3. (TCO 3) What happens next if a router determines that an incoming
packet has a destination of a directly connected network? (Points : 2) Check the ARP cache
and forward packet to local host.
Check the routing table for lowest cost path.
Drop the packet and send a control message to the source address.
Encapsulate the packet into a destination IP address before forwarding.
Forward the packet to the next hop.
Type: MCQuestion 4.4. (TCO 3) The arrangement of the cables, network devices, and end
systems in a network is called its _____. (Points : 2) logical topology
logical network overlay
physical topology
configuration topology
None of the above
Type: MCQuestion 5.5. (TCO 3) Being able to use a single physical router interface to route
traffic between multiple VLANs on a network is called _____. (Points : 2) hub and spoke
router

2. sub-interface VLAN routing
composite VLAN routing
trunk-safe router
router-on-a-stick
Type: MCQuestion 6.6. (TCO 3) What is a disadvantage of traditional routing? (Points : 2)
Does not support mutli-hop routing
Can create layer-two loops
Transport too many VLAN-tagged packets
Can create layer 3 routing loops
All of the above
Type: MCQuestion 7.7. (TCO 3) The command used on a Cisco Catalyst 2960 switch to change
the switched database manager (SDM) template is _____. (Points : 2) sdm change
sdm use
sdm prefer
sdm enable
None of the above
Pool 9 – 3:1; 2 points; address TCO 3
Type: MCQuestion 8.8. (TCO 3) Which of the following is the proper format for assigning an
IPv4 address to the interface on a Cisco router? @ See Chapter 4, page 175. (Points : 2) ip
address ip-address subnet-mask
ip address ip-address
assign address ip-address subnet-mask
interface ip-address
None of the above
Type: MCQuestion 9.9. (TCO 3) Which command would you use to troubleshoot a routing
problem between a router and a switch? (Points : 2) show interface ip brief
debug ip route
Debug interface ip
show ip protocols
show ip route
Question 1.1. (TCO 3) This network appears to be working most of the time but lately it

3. becomes slower and slower as new end devices and applications come online. What is the
characteristic that is violated? (Points : 2) Security
Availability
Reliability
Manageability
Scalability
Pool 2 – 5:1; 2 points; address TCO 3
Type: MCQuestion 2.2. (TCO 3) Routers use the routing table to _____. (Points : 2) select
the best path toward the destination
encapsulate layer 3 packets before they are sent to the egress interface
determine the way of reaching the host on the ingress interface
exchange network reachability information with each other
C and D
Type: MCQuestion 3.3. (TCO 3) What happens next if a router determines that an incoming
packet has a destination of a directly connected network? (Points : 2) Check the ARP cache
and forward packet to local host.
Check the routing table for lowest cost path.
Drop the packet and send a control message to the source address.
Encapsulate the packet into a destination IP address before forwarding.
Forward the packet to the next hop.
Type: MCQuestion 4.4. (TCO 3) The arrangement of the cables, network devices, and end
systems in a network is called its _____. (Points : 2) logical topology
logical network overlay
physical topology
configuration topology
None of the above
Type: MCQuestion 5.5. (TCO 3) Being able to use a single physical router interface to route
traffic between multiple VLANs on a network is called _____. (Points : 2) hub and spoke
router
sub-interface VLAN routing
composite VLAN routing

4. trunk-safe router
router-on-a-stick
Type: MCQuestion 6.6. (TCO 3) What is a disadvantage of traditional routing? (Points : 2)
Does not support mutli-hop routing
Can create layer-two loops
Transport too many VLAN-tagged packets
Can create layer 3 routing loops
All of the above
Type: MCQuestion 7.7. (TCO 3) The command used on a Cisco Catalyst 2960 switch to
change the switched database manager (SDM) template is _____. (Points : 2) sdm change
sdm use
sdm prefer
sdm enable
None of the above
Pool 9 – 3:1; 2 points; address TCO 3
Type: MCQuestion 8.8. (TCO 3) Which of the following is the proper format for assigning an
IPv4 address to the interface on a Cisco router? @ See Chapter 4, page 175. (Points : 2) ip
address ip-address subnet-mask
ip address ip-address
assign address ip-address subnet-mask
interface ip-address
None of the above
Type: MCQuestion 9.9. (TCO 3) Which command would you use to troubleshoot a routing
problem between a router and a switch? (Points : 2) show interface ip brief
debug ip route
Debug interface ip
show ip protocols
show ip route
Solution

5. 1) option C .reliability
2) option A select best path towards destination
3) option A check ARP cache and forward the packet
4) option E none of the above
5) option B sub interface vlan routing
6) option E all of above
7) option C
8)option C
9) option C debug interface ip