The document provides steps for site engineers to commission a BTS CC card and troubleshoot issues. It includes: 1) Commissioning the CC card using the LMT tool to burn an image or import an MO file via online configuration. 2) Confirming the software version is fully updated across all packages and resolving any version issues. 3) Viewing the topology in LMT and connecting boards and fibers accordingly. 4) Identifying irrelevant versus related alarms that could occur in pre-swap, and providing potential solutions to address issues.

1. PRE-COMMISSIONING &
TROUBLESHOOTING STEPS FOR
SITE ENGINEERS
1

2. Scope of Presentation:
• Commissioning of BTS CC card in Pre-swap
• Software Version up-gradation Methods
• Follow steps on Configuration Diagram in LMT
• Troubleshoot the alarms one-by-one
2

3. Commissioning of CC card
• First of all, confirm that you have required version of LMT(LMT_v12.13.43P02_GUL)
3

4. Commissioning of CC card
• After that you must apply setting to you laptop LAN IP like following.
4

5. Commissioning of CC card
• Now open “EOMS” file from LMT as mentioned below.
5

6. Commissioning of CC card
• EOMS will open a windows like below then select “Image and burn” and press “OK”
6

7. Commissioning of CC card
• It will ask for selection of RADIO MODE, select “MULTIMODE”
7

8. Commissioning of CC card
• Select PATCH Directory & Commissioning File then press “OK”
8

9. Commissioning of CC card
• After that LMT will start the process of image burning.
9

10. Commissioning of CC card
• It will take a while
10

11. Commissioning of CC card
Burning/MO file Succeeded
when it will be succeeded the display shows
11

12. 12
Commissioning of CC card(2nd Method)
Select “Online Configuration” & press “Station”.
Fill the Station Name & Station IP field.

13. 13
Commissioning of CC card (2nd Method)
Give User name “admin” and left password field blank. Then press OK to login.

14. 14
Commissioning of CC card (2nd Method)
Go to “System” and select “Import”. After that select the MO file in xml format. Press OK.

15. Commissioning of CC Card
• After completed process & reset of CC board, you can login again in EOMS and
you can see the following window. It would show you the topology.
15

16. Expected Alarms in EFMS
• You can login to EFMS and you can see the alarms.
16

17. View the Topology and follow it
• Connect the boards & fiber cables according to the topology shown in LMT.
17

18. View the Topology and follow it
• Connect the boards & fiber cables according to the topology shown in LMT.
18

19. View the Topology and follow it
19

20. Confirming the Software Version
• Go to System and select Version Management to confirm the
Version
20

21. Confirming the Software Version
• Version must be 4.13.10.38P42. All versions must be in RUN condition. In case
of 3G site, UMTS package must also be available.
21

22. Confirming the Software Version
• In case software is not updated, just right click on Local window and add
the package files.
22

23. Confirming the Software Version
• In case software is not updated, just right click on Local window and add
the package files.
23

24. Confirming the Software Version
• It will take some time to upload.
24

25. Confirming the Software Version
• After that, right click on the package files on Local Window and select
“Download”. It will download the files.
25

26. Key Points for software downloading
• After commissioning, first confirm running the package version.
• Running package version must be 4.13.10.38P42
• If the running version is still old one we need to active the new one
again.
• In case, package files are corrupted or not active successfully, first
Delete the files by right click on it and then download again.
• If you download again without deleting it, it may cause capacity issue.
• In case, you don’t understand above points or you cannot resolve any
issue, contact concerned troubleshooting person on call.
26

27. Irrelative Alarms on Pre-Swap
• Antenna related alarms.(VSWR, Carrier uplink etc)
• SCTP alarm.
• Link broken between OMM and NE.
• SNTP time adjustment alarm.
• 1588 Clock source fault.
• The physical Ethernet link is broken.
27

28. Related Alarms in Pre-Swap
• Optical port receiving link failure(198098319)
• The RRU link is broken(198097605)
• Hardware type is different from the configuration(198092029)
• Device power down(198092295)
• Version package fault(198097567)
• Unavailable optical module(198098318)
• Software runs abnormally(198097604)
• Carrier downlink data problem(198098471)
• The board is not in position(198092072)
• Carrier uplink data is abnormal.(198093053)
• Disable PA(198098440)
• Initialization failure(198092070)
• The board is not configured(198092203)
• The board is powered off(198092057)
• Board communication link interrupted(198097060)
• Internal fault(198098467)
• Software loading is abnormal(198093056)
28

29. Alarms & Solution
29

30. Alarms & Solution
30

31. 31
Alarms & Solution

32. 32
Alarms & Solution

33. 33
Alarms & Solution

34. 34
Alarms & Solution

35. 35
Alarms & Solution

36. 36
Alarms & Solution

37. 37
Alarms & Solution

38. Questions…
• In Live BTS, if GSM (2G) is down, UMTS (3G) will effect of not?
• In the worst scenario, if you have to edit the MO file on site, how you
will do it?
One More thing…
After pre-swap, the site engineer must feedback the snapshot of EFMS
to region management (Mr. Adeel and CC to us) as to confirm the pre-
swap is successful or not.
38

39. THANK YOU
39