This document discusses various options for plastic waste management, including recycling, disposal through plasma pyrolysis technology, and conversion to liquid fuel. It summarizes studies on:
1) Recycling technologies like primary, secondary, tertiary, and quaternary recycling.
2) The performance of roads made from recycled plastics.
3) A study evaluating a plasma pyrolysis technology for plastic waste disposal.
4) A process for converting plastic waste to liquid fuel and its environmental impacts.
5) A study examining the biodegradability of various plastics.
Treatment of Effluent from Granite Cutting Plant by Using Natural Adsorbents ...IJERD Editor
Granite cutting plant is one such industry that releases polluting and turbid effluent. The residue from all these processes is discharged with water as an effluent. The effluent mainly contains many solids that harm the environment. Hence it requires treatment techniques before disposal. Several conventional methods are available for removal of contaminants like coagulation, adsorption, polyelectrolyte methods and biological methods. Most of them are cost prohibitive. The reduction of solids concentration in the effluent before disposal by using the techniques, coagulation followed by adsorption using natural adsorbents, like rice husk carbon and saw dust carbon, in contrast to the usage of activated carbon as it is costly. From a local Granite cutting plant near Anantapur, the effluent is collected and its physico-chemical characteristics are estimated and found to be pH(7.5), TS(4240mg/l), TSS(21560mg/l), TDS(12373mg/l).Effluent obtained is subjected to coagulation by potash alum followed by adsorption using saw dust carbon and rice husk carbon.
Textile Wastewater Treatment in BangladeshMahmudul Hasan
What is wastewater, textile wastewater treatment, Major Pollutants in textile wastewater, Steps of textile wastewater treatment, Brief overview of textile wastewater in Bangladesh.
Treatment of Effluent from Granite Cutting Plant by Using Natural Adsorbents ...IJERD Editor
Granite cutting plant is one such industry that releases polluting and turbid effluent. The residue from all these processes is discharged with water as an effluent. The effluent mainly contains many solids that harm the environment. Hence it requires treatment techniques before disposal. Several conventional methods are available for removal of contaminants like coagulation, adsorption, polyelectrolyte methods and biological methods. Most of them are cost prohibitive. The reduction of solids concentration in the effluent before disposal by using the techniques, coagulation followed by adsorption using natural adsorbents, like rice husk carbon and saw dust carbon, in contrast to the usage of activated carbon as it is costly. From a local Granite cutting plant near Anantapur, the effluent is collected and its physico-chemical characteristics are estimated and found to be pH(7.5), TS(4240mg/l), TSS(21560mg/l), TDS(12373mg/l).Effluent obtained is subjected to coagulation by potash alum followed by adsorption using saw dust carbon and rice husk carbon.
Textile Wastewater Treatment in BangladeshMahmudul Hasan
What is wastewater, textile wastewater treatment, Major Pollutants in textile wastewater, Steps of textile wastewater treatment, Brief overview of textile wastewater in Bangladesh.
Application of response surface methodology for biosorption of reactive dyes ...IJLT EMAS
Response Surface Methodology was employed for
studying the biosorption of reactive dyes from textile effluent by
utilization of dead biomass of Rhizopus arrhizus in a batch
system. Central Composite Design at the specified combinations
of four variables (pH, biosorbent dosage, speed of agitation,
contact time) was adopted to achieve maximum biosorption. The
fitted quadratic model (P<0.0001) was used to arrive at the best
operating conditions. Under the following optimum conditions
i.e., pH 2.0; biosorbent dosage 3 g /L; speed of agitation 80 rpm
and contact time 60 min, 99.60% of the dyes were removed from
the wastewater. The mechanism of biosorption was elucidated by
FTIR, XRD and BET analysis. This work demonstrated the
feasibility of employing Rhizopus arrhizus as an effective and
economical fungal biosorbent for the removal of dyes from the
textile effluent.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Anaerobic treatment of Pulp and Paper mill Bleaching Effluent Amit Christian
Anaerobic treatment of Pulp and Paper Mill Bleaching effluent using fluidized bed reactor using LEVAPOR carriers . It offered huge space and energy savings for the treatment of toxic effluent
Investigation on effluent characteristics of organic cotton fabric dyeing wit...Elias Khalil (ইলিয়াস খলিল)
Environmental sustainability is the major concern in the age of modern world. For textile and apparel sector, this has been a burning issue for many related concerned bodies. The pretreatment and dyeing process of greige fabrics results in large volume of effluents that has harmful effect on environment. In this study, the ecological parameters of the effluents obtained from scouring and dyeing of 100% organic cotton single jersey knitted fabrics with environmentally low impact Remazol series reactive dyes adopting exhaust dyeing method was investigated. The effluents collected for investigating the ecological parameters include chemical oxygen demand (COD), biological oxygen demand (BOD), total dissolved solids (TDS), total suspended solids (TSS), dissolved oxygen (DO) and alkalinity. The results show that the use of the low impact reactive dyes has greater ecological advantages as it reduces the COD, BOD, TDS, TSS, pH values and increases the DO values of effluents. Organic cotton itself being eco-friendly along with Remazol series sustainable dyes provides the better ecological results. Hence, the results indicated that wet processing of organic cotton knitted fabric with eco-friendly and low impact reactive dyes provide better ecological advantages.
These slides use concepts (e.g., scaling) from my (Jeff Funk) course entitled analyzing hi-tech opportunities to analyze how membranes have and are becoming more economically feasible for one application, pervaporation. The economic feasibility of pervaporation is improved as temperatures and pressures of the systems are increased, which are facilitated by larger scale, and as the membranes are improved. Membranes become cheaper as they are made thinner (example of scaling) and they become better as the pore size is made both smaller and is designed for allowing specific molecules to pass through the pores.
Application of response surface methodology for biosorption of reactive dyes ...IJLT EMAS
Response Surface Methodology was employed for
studying the biosorption of reactive dyes from textile effluent by
utilization of dead biomass of Rhizopus arrhizus in a batch
system. Central Composite Design at the specified combinations
of four variables (pH, biosorbent dosage, speed of agitation,
contact time) was adopted to achieve maximum biosorption. The
fitted quadratic model (P<0.0001) was used to arrive at the best
operating conditions. Under the following optimum conditions
i.e., pH 2.0; biosorbent dosage 3 g /L; speed of agitation 80 rpm
and contact time 60 min, 99.60% of the dyes were removed from
the wastewater. The mechanism of biosorption was elucidated by
FTIR, XRD and BET analysis. This work demonstrated the
feasibility of employing Rhizopus arrhizus as an effective and
economical fungal biosorbent for the removal of dyes from the
textile effluent.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Anaerobic treatment of Pulp and Paper mill Bleaching Effluent Amit Christian
Anaerobic treatment of Pulp and Paper Mill Bleaching effluent using fluidized bed reactor using LEVAPOR carriers . It offered huge space and energy savings for the treatment of toxic effluent
Investigation on effluent characteristics of organic cotton fabric dyeing wit...Elias Khalil (ইলিয়াস খলিল)
Environmental sustainability is the major concern in the age of modern world. For textile and apparel sector, this has been a burning issue for many related concerned bodies. The pretreatment and dyeing process of greige fabrics results in large volume of effluents that has harmful effect on environment. In this study, the ecological parameters of the effluents obtained from scouring and dyeing of 100% organic cotton single jersey knitted fabrics with environmentally low impact Remazol series reactive dyes adopting exhaust dyeing method was investigated. The effluents collected for investigating the ecological parameters include chemical oxygen demand (COD), biological oxygen demand (BOD), total dissolved solids (TDS), total suspended solids (TSS), dissolved oxygen (DO) and alkalinity. The results show that the use of the low impact reactive dyes has greater ecological advantages as it reduces the COD, BOD, TDS, TSS, pH values and increases the DO values of effluents. Organic cotton itself being eco-friendly along with Remazol series sustainable dyes provides the better ecological results. Hence, the results indicated that wet processing of organic cotton knitted fabric with eco-friendly and low impact reactive dyes provide better ecological advantages.
These slides use concepts (e.g., scaling) from my (Jeff Funk) course entitled analyzing hi-tech opportunities to analyze how membranes have and are becoming more economically feasible for one application, pervaporation. The economic feasibility of pervaporation is improved as temperatures and pressures of the systems are increased, which are facilitated by larger scale, and as the membranes are improved. Membranes become cheaper as they are made thinner (example of scaling) and they become better as the pore size is made both smaller and is designed for allowing specific molecules to pass through the pores.
Plastic Waste Management and Recycling TechnologiesBHU
Its time to prevent the plastic usage by using 4Rs such as- Refuse, Reduce, Reuse and Recycle.
How to manage and utilize the Plastic Waste with the developed Technologies for Recycling.
#1 INTRODUCTION-The term “plastics” includes materials composed of various elements such as carbon, hydrogen, oxygen, nitrogen, chlorine, and sulphur.
Plastics are macromolecules, formed by polymerization and having the ability to be shaped by the application of reasonable amount of heat and pressure or any other form of forces.
It is one of the few new chemical materials which pose environmental problem.
Polyethylene, polyvinyl chloride, polystyrene is largely used in the manufacturing of plastics.
##2Rapid population growth, urbanization and industrial growth have led to severe problem of waste generation in urban centres.
The waste quantities increased from 46 million tones in 2001 to 65 million tones in 2010.
Report says that per capita per day production will increase to 0.7 kg in 2050.
The characteristics of waste depends on various factors such as food habits, traditions, lifestyle, climate etc.
for more contect
Plastic Waste Management and Recycling Technology : P2Vignesh Sekar
To emphasize the reduced use of plastic and the beneficial management of plastic waste. Efficient transformation of plastic into energy and fuel. Making our environment an eco friendly zone. Modify the design of recycling Machines. Install the recycling unit at TNAU. Compare the envi.factors of Coimbatore with other cities. Making our Eco fest - 15------Plastic free & Models
Conversion of Waste Plastic to Fuel by Hitesh SharmaHitesh Sharma
Pyrolysis is a process which involves thermochemical decomposition of organic matter at high temperature (>370◦C) in the absence of oxygen. Products of this process are Pyrolysis Oil, Carbon Black, and Hydrocarbons. This review paper is focusing the most efficient and widely used method of converting plastics to fuels: ‘Pyrolysis’ and its effectiveness on resolving the both issues of waste plastic management and the requirement of a good alternative fuel for use.
A Research onto Study the Properties of Concrete with Partial Replacement of ...ijtsrd
Plastic waste management is the main environmental issues in our country. The present study applies to the usage of recycled plastics as an alternative for aggregates in concrete. The motive of the study is to investigate the alteration in the physical qualities of concrete by the use of waste of plastics in concrete. The utilization of plastic aggregates was discovered to lead to the development of sturdy concrete. Additionally, with the plastics, the tensile and compressive strength of the concrete reduces. The foremost change brought approximately by using plastics is the fact that concrete’s thermal conductivity is decreased due to the utilization of plastics. It is able to thus be declared recycled plastics are usually utilized for thermal insulation of structures.Series of experiments had been performed in this current study for a comparison of the usage of Used Plastic as a replacement of sand in various different proportions. The main conclusions drawn was that the compressive strength increases with the inclusion of Used Plastic upto a certain proportions and then reduces the strength. Paras Kumar Yadav | Amit Kumar "A Research onto Study the Properties of Concrete with Partial Replacement of Aggregates by Plastic Aggregates" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-5 , August 2020, URL: https://www.ijtsrd.com/papers/ijtsrd33250.pdf Paper Url :https://www.ijtsrd.com/engineering/civil-engineering/33250/a-research-onto-study-the-properties-of-concrete-with-partial-replacement-of-aggregates-by-plastic-aggregates/paras-kumar-yadav
A study on the plastic waste treatment methods for road constructionIJARIIT
Plastic found in different forms is almost 5% amongst municipal solid waste, which can prove to be toxic in nature. It
is a common sight in both urban and rural areas to find empty plastic bags and another type of plastic packing material littering
the roads as well as drains. Due to its biodegradability, it creates stagnation of water and associated hygiene problems. In order
to contain this problem experiments have been carried out whether this waste plastic can be reused productively in the
construction of roads. The experimentation at several institutes indicated that the waste plastic, when added to hot aggregate
will form a fine coat of plastic over the aggregate and such aggregate, when mixed with the binder is found to give higher
strength, higher resistance to water and better performance over a period of time. Therefore, it is proposed that we may use waste
plastic in the construction of Rural Roads.
1. Options for Plastic Waste Management
Recycling of plastics through environmentally sound manner :
Recycling of plastics should be carried in such a manner to minimize
the pollution level during the process and as a result to enhance the
efficiency of the process and conserve the energy. Plastics recycling
technologies have been historically divided into four general types -
primary, secondary, tertiary and quaternary.
Primary recycling involves processing of a waste/scrap into a product
with characteristics similar to those of original product.
Secondary recycling involves processing of waste/scrap plastics into
materials that have characteristics different from those of original
plastics product.
Tertiary recycling involves the production of basic chemicals and fuels
from plastics waste/scrap as part of the municipal waste stream or as a
segregated waste.
Quaternary recycling retrieves the energy content of waste/scrap
plastics by burning/incineration. This process is not in use in India.
Steps Involved in the Recycling Process
Selection The recyclers/reprocessors have to select the waste
/scrap
which are suitable for recycling /reprocessing.
Segregation The plastics waste shall be segregated as per the codes
1-7
mentioned in the BiS guidelines (IS:14534:1998).
Processing After selection and segregation of the preconsumer waste
(factory waste ) shall be directly recycled .. The post
consumer waste (used plastic waste) shall be washed,
shredded, agglomerated, extruded and granulated
Special Note:
2. “All medical plastics waste and packings of toxic contents such as
pesticides,
Insecticides shall be segregated separately and may be processed
through Plasma Pyrolysis Technology (PPT)”
Photo: The Newly Developed Pilot Plant (extruder, control panel & part of pollution
monitoring System.
Performance of Built Roadsmade from Plastics Waste:
A study has been entrusted to evaluate the performance of polymer
coated built
roads to Thiagarajar College of Engineering Madurai.
The specific task (objectives) of the study are given below
To measure the roughness of the pavement surface;
To measure the resistance offered by the pavement surface against
skidding of vehicles;
To measure the pavement macro texture for the geometrical
deposition;
3. To assess the structural evaluation of flexible pavement for the
strength of the same;
To measure the field density of the road;
To study the gradation of the road;.
To carry out different tests on recovered bitumen;
To examine the condition of the road (Cracks, raveling, potholes,
rutting, corrugation edge break etc.).
Special Note:
Polymer blended bitumen shows higher softening point, lower
penetration point,
and better ductility. Polymer coated aggregate blended with Bitumen
shows
higher Marshall value and better stripping value, hence the polymer
coated mix is
more suited for road laying than mixing of shredded plastics into
bitumen.
Photo: Mixing of Shredded Polymer on coarse aggregate
Observations of the Field Test
The coating of plastic reduces the moisture absorption of the
aggregate. Normally 2% is the limit for absorption. Whereas the
polymer coated aggregate is having almost nil absorption.
4. The moisture absorption values are correlated with voids. The voids
are reduced in Polymer Coated Aggregate. Thus the quality of the
aggregate is improved.
Moreover the removal of voids and the reduction of moisture
absorption results into prevention of stripping of bitumen.
The polymer coating reduces the porosity of the aggregate and hence
result in improving soundness of the aggregate. Once the pores are
covered with plastics the possibility of entering the salt at the surface is
prevented.
The polymer coated aggregate is practically a plastic laminated
aggregate,
thus prevents wetting with water so there is no stripping.
Results of Field Test:
The coating of plastics over aggregate improves Impact, Los Angels Abrasion
and Crushing Value with the increase in the percentage of plastics. After the
three phases of field experiments, the following important conclusion have
been drawn.
The extracted bitumen showed almost near value for Marshall stability.
The entire road was having good skid resistance and texture values.
All the stretches in the roads are reasonably strong.
The unevenness index values of these three sections are nearly 3000
mm/km, which indicates a good surface evenness.
The plastic tar roads have not developed any potholes, rutting, raveling
or
edge flaw, even though these roads are more than two years of age.
Polymer coated aggregate bitumen mix performs well compared to
polymer modified bitumen mix.
Higher percentage of polymer coating improves the binding strength of
the
mix.
5. Foam plastics have better binding values.
Plastics Waste Disposal through Plasma Pyrolysis Technology (PPT)
Plasma Pyrolysis Technology (PPT)- An Introduction
Plasma Pyrolysis is a state of the art technology, which integrates the
thermo-chemical properties of plasma with the pyrolysis process. The
intense and versatile heat generation capabilities of Plasma Pyrolysis
technology enable it to dispose of all types of plastic waste including
polymeric, biomedical and hazardous waste in a safe and reliable
manner. Pyrolysis is the thermal disintegration of carbonaceous
material in oxygen-starved atmosphere. When optimized, the most
likely compounds formed are methane, carbon monoxide, hydrogen
carbon dioxide and water molecules.
Process Technology:
In Plasma Pyrolysis, firstly the plastics waste is fed into the primary
chamber at 8500C through a feeder. The waste material dissociates
into carbon monoxide, hydrogen, methane, higher hydrocarbons etc.
Induced draft fan drains the pyrolysis gases as well as plastics waste
into the secondary chamber where these gases are combusted in the
presence of excess air. The inflammable gases are ignited with high
voltage spark. The secondary chamber temperature is maintained at
10500 C. The hydrocarbon, CO and hydrogen are combusted into safe
carbon dioxide and water. The process conditions are maintained such
that it eliminates the possibility of formation of toxic dioxins and furans
molecules (in case of chlorinated waste). The conversion of organic
waste into non toxic gases (CO2, H2O) is more than 99% . The
extreme conditions of Plasma kill stable bacteria such as bacillus
stereo-thermophilus and bacillus subtilis immediately. Segregation of
the waste is not necessary, as the very high temperatures ensure
treatment of all types of waste without discrimination.
6. A study has been entrusted to FCIPT ,Institute of Plasma Research
(IPR) ,Gandhinagar to evaluate the performance of PPT.
Objectives of the Study:
The disposal of plastics waste is ever increasing problem and no
holistic approach could be developed. Considering the grave concern
for plastics waste management, an effective technology has been put
forth. To ascertain the performance of PPT, a Memorandum of
Understanding (MoU) has entered between the Institute of Plasma
Research, acting through its Facilitation Centre for Industrial Plasma
Technologies and Central Pollution Control Board, Ministry of
Environment & Forests, Government of India., The objectives of the
study are reiterated below;;
To conduct a performance study of the Plasma Pyrolysis Technology
on 15 kg/hr prototype demonstration system developed by FCIPT/IPR
for proper disposal of plastics waste and also monitor parameters e.g
suspended particulate matter(SPM), carbon monoxide(CO),
hydrocarbon(HC) benzene, dioxins, furans etc. with regards to gaseous
emissions.
To conduct experiments on safe disposal of plastics waste using
higher capacity (approx. 50 kg/hr) plasma pyrolysis system as
developed by FCIPT.
CPCB may set up prototype plasma pyrolysis plant on demonstration
basis (15 kg/hr waste disposal capacity) as specific locations( hilly and
pilgrimage) identified by CPCB in consultation with States.
Conversion of Plastics Waste into liquid fuel
7. Another solution for disposal of plastics waste has been consider by
CPCB i.e conversion of plastics waste into liquid fuel.
Process Technology
A Research-cum-Demonstrative Plant was set up at Nagpur for
conversion of
waste plastics into liquid fuel oil. The process adopted is based on
random de-polymerization of waste plastics in presence of a catalyst
into liquid fuel. The entire process is undertaken in closed reactor
vessel followed by condensation, if required. Waste plastics while
heating upto 2700 to 3000 C convert into liquid-vapour state, which is
collected in condensation chamber in the form of liquid fuel. The tarry
liquid waste is topped-down from the heating reactor vessel. The
organic gas is generated which is presently vented due to lack of
storage facility, however, the gas can be used in dual fuel diesel-
generator set for generation of electricity.
The process includes following steps;
Collection & segregation of plastics waste
Storing of Plastics waste
Shredding of wastes
Feeding into hopper
Flow of waste into heating vessel in presence of
catalyst
Tapping of liquid/
Vissels tarry waste
Movement of liquid-vapor into condenser
Tapping of liquid fuel (as a product)
8. Environment Related Observations
There are no liquid industrial effluents and no floor washing as waste
material is not washed.
There is no organized stack and process emissions are let out.
Odour of volatile organics has been experienced in the processing area
due to some leakages or lack of proper sealing
Since, absolute conversion of liquid-vapor was possible into liquid,
some portion of gas (about 20%) is connected to the generator.
However, the process will be improved in full scale plant.
PVC plastics waste is not used and if used, it was less than 1%. In
case PVC is used, the chlorine can be converted into hydrochloric
acid as a by-product.
The charcoal (Charcoal is formed due to tapping of tarry waste)
generated during the process has been analysed and contain heavy
metals, poly aromatic hydrocarbon (PAH) which appears to be
hazardous in nature. The source of metals in charcoal could be due to
presence of additives in plastics and multilayer & laminated
plastics.
Monitoring of process fugitive emissions in the work area as well as
emissions from the engines/diesel generator sets, where this liquid fuel
is used, for various parameters such as CO, HCl, Styrene, Benzene,
VOCs is necessarily required.
Recommendations of CPCB:
As regard technology is concerned, the process could be adopted only
for converting post-consumer plastics waste into liquid fuel. The
process may work well with the selected plastics waste. For other
9. category of plastics waste, further research need to be carried out. The
technology needs to be established for demonstrating use of post-
consumer plastics to reduce menace of plastics waste disposal along
with municipal solid waste (MSW)
There should be proper utilization of unconverted gas and in no case
such gaseous emission should be let out freely.
As far as possible, use of PVC waste should be avoided and in case it
is used, it should be converted into hydrochloric acid and no
emissions be let out.
The gaseous emissions may be tested in case the liquid fuel is used
for furnaces/ boilers and generator.
In the processing area, monitoring of VOCs should be carried out to
check concentrations of various hazardous air pollutants.
Metal and organic concentration need to be checked in charcoal to
ascertain its hazardous nature.
The fuel quality may be checked by the concerned agency like Indian
Oil Corporation Limited (IOCL), which may certify the liquid fuel
quality as per the specifications and suggest for its best use.
As far as prescription of environmental standards are concerned, no
standards to be prescribed for liquid effluents. For gaseous
emissions, the entire process is to be closed and no leakages are
expected. In working area, VOC standards could be worked out. No
gaseous effluents are expected to be let out and if any, these are to
use in generators.
When PVC is used, complete conversion to HCl and no emission of
HCl vapors could be stipulated. Further, disposal of HCl may also be
ensured.
10. In case of use of unwashed/unsegregated post-consumer plastics
waste ( as in the present case), the quality of fuel is expected to be
deteriorated as well process fugitive emissions may vary, therefore, it
needs to be evaluated and compared with clean waste before
technology approval.
It is proposed to carry out detailed air quality monitoring by
SPCBs/PCCs of requisite parameters in work area Besides, emission
monitoring of DG sets/engines, in which this liquid fuel is used, shall
also be carried out to ascertain compliance of parameters prescribed
by SPCB/CPCB for DG sets.
Biodegradable Plastics
Generally plastics are non-biodegradable; the environmentally degradable
polyolefin films are defined as those materials that contain degradation
process of polyolefin article (bag/film/sheet) under conditions of composting.
Often queries are raised regarding biodegradability of plastics but clear-cut
answer is not available about the biodegradability of plastics. In view of
above, CPCB has entrusted a comprehensive study to Central Institute of
Plastics Engineering and Technology (CIPET) to establish the
biodegradability and compostability (e.g. fragmentation rate, degradation rate
and safety) of known and unknown polymeric material available in India and
abroad .Microorganisms use the carbon substrate to extract chemical energy
for driving their life processes by aerobic oxidation of glucose and other
readily utilizable C-substrate as shown by the following equation:
C6H12O6 + 6 O2 6 CO2 + 6 H2O ( ∆G0 = - 686 kcal/mol )
The main objectives of the proposed study include the followings:
To inventories/assess the manufacturing status of biodegradable
plastics in India particularly with reference to processing technologies
and the environmental issues etc.
To establish the degradation rate (change in chemical structure,
decrease in mechanical strength, fragmentation or weight loss) of the
11. polymeric material or plastics material under laboratory scale
composting conditions
To find out self-life and its impact on environment (soil, water of
plastics w.r.t. colour/additives once it is disposed);
Effect on foodstuffs w.r.t. natural colour/additives
Process Methodology:
To test the biodegrability following procedure has been adopted;
(a) Inventorisation of Manufacturing units of biodegradable
/degradable plastics & collection of sample from
Industries/Hospitals/Hotels/Restaurants
(b) Analysis of biodegradable/degradable films through ASTM
and international consensus standard on biobased content
qand biodegrability . The following ASTM specification has
neen used in present investigation;
ASTM D-5209; Standard Test method for determining the Aerobic
Biodegradation of plastic materials in presence of Municipal Sludge.
ASTM D-5338: Standard Test method for determining the Aerobic
Biodegradation of plastic materials under controlled composting
conditions.
ASTM D-6400: Specifications for Compostable Plastics
(c )Disintegration
(d )Safety
(e)Collection of D2W additives & analysis of its toxicity
Results of the lab study:
The study is still going on. The test results of the films collected from
certain industries have the average biodegradation to the tune of
4.40% 6.66% & 40.35 % respectively.
The test results of the sample from the hotels / Restaurants & Hospitals
showed biodegradation ranging from 8.46% to 29.97% respectively.
12. The minimum percentage of biodegradation of a product made from a
single polymer
should be 60% in 45 days span in the present context & standards
practiced world wide.
In the present study samples collected so far are not conforming to the
requirement of prescribed biodegradation level as per ASTM D -6400.
(Clause 6.3.1)
The toxicity level of masterbatch additives is under investigation