This document summarizes research on Potential Induced Degradation (PID) in wafer-based silicon solar cells and panels. PID occurs when cells are exposed to high voltages relative to ground, causing power degradation over time. The paper describes test setups to simulate PID and investigate influencing factors. Key findings are that cell properties like anti-reflective coating parameters and wafer material/resistivity impact PID susceptibility. Panel design factors like encapsulant material choice also influence PID by affecting leakage currents between the cell and ground under humidity and voltage stress. Preventing PID requires consideration of cell properties and panel design choices to minimize long-term power losses in large solar installations.
This document provides an introduction and overview to the Blogger for Beginners guide. It summarizes the guide's contents and structure. The guide is divided into 10 chapters that will help new users get started with Blogger, write blog posts, customize their blog, add content and widgets, configure comments and feeds, publish posts, and learn more about using Blogger. It aims to explain the key Blogger features and functionality in an easy-to-follow manner through step-by-step instructions and screenshots.
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently.
Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
https://www.n-denkei.com/singapore/inquiry/
Using Design of Experiments Approach to analysis Factors Effecting on the PV ...ijtsrd
Many factors affect the performance of a PV module. In this experiment, we will use the factorial experimental design method to investigate these factors. Several factors are studied in this experiment such as phase change martial type, PCM thickness, fin length thickness, fin count and the wind speed. A factorial design is often used by scientists wishing to understand the effect of two or more independent variables upon a single dependent variable so applying factorial design in PV parameters will give us the most significant parameter on the temperature of the cells. The statistical results showed that the most significant factors affected on the temperature of the cells are PCM thickness and wind speed. Malik Al-Abed Allah | Mahdy Migdady "Using Design of Experiments Approach to analysis Factors Effecting on the PV Cells" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-5 , August 2020, URL: https://www.ijtsrd.com/papers/ijtsrd33065.pdf Paper Url :https://www.ijtsrd.com/engineering/mechanical-engineering/33065/using-design-of-experiments-approach-to-analysis-factors-effecting-on-the-pv-cells/malik-alabed-allah
IRJET - Effects of Temperature and Dust on the Behavior of Photovoltaic SystemsIRJET Journal
This document summarizes a study on the effects of temperature and dust on the performance of photovoltaic systems. Three photovoltaic systems were tested - one with an automatic cooling and cleaning system to maintain the module temperature at 40°C, one with clean modules but no cooling, and one with dusty modules. Measurements of voltage, current, power and temperatures were taken every 10 minutes over 5 hours. The results showed that maintaining the module temperature at 40°C using the cooling system increased energy generation by 26.17% compared to the non-cooled clean module, and improved performance compared to the dusty module.
The document analyzes various factors that affect the performance of photovoltaic (PV) systems. It discusses factors experimentally shown to influence PV module performance such as cable thickness, temperature, shadows, dust particles, charge controllers, and solar cell IV characteristics. It also discusses factors theoretically shown to affect performance such as environmental and operating conditions, solar radiation, spectrum effects, degradation, air mass flow, maximum power point tracking, inverter efficiency, and battery efficiency. The document presents experimental results measuring the effects of these factors on voltage, current, and output power of a PV system over time. It concludes that PV module performance depends on environmental conditions like temperature, irradiation, dust, and shadows.
An optimum location of on-grid bifacial based photovoltaic system in Iraq IJECEIAES
Bifacial photovoltaic (PV) module can gain 30% more energy compared to monofacial if a suitable location were chosen. Iraq (a Middle East country) has a variable irradiation level according to its geographic coordinates, thus, the performance of PV systems differs. This paper an array (17 series, 13 parallel) was chosen to produce 100 kWp for an on-grid PV system. It investigates the PV system in three cities in Iraq (Mosul, Baghdad, and Basrah). Effect of albedo factor, high and pitch of the bifacial module on energy yield have been studied using PVsyst (software). It has been found that the effect is less for a pitch greater than 6 m. The energy gained from bifacial and monofacial PV system module in these cities shows that Mosul is the most suitable for installing both PV systems followed by Baghdad and lastly Basrah. However, in Basrah, the bifacial gain is 12% higher in the energy than monofacial as irradiation there is higher than the other locations, especially for elevation above 1.5 m. Moreover, the cost of bifacial array is 7.23% higher than monofacial, but this additional cost is acceptable since the bifacial gain is about 11.3% higher energy compared to the monofacial.
This document summarizes photovoltaic degradation rates reported in published literature from field testing over the last 40 years. It begins with a brief historical outline of early photovoltaic development and field testing in the US, Europe, Japan, and Australia. The document then analyzes nearly 2,000 degradation rates reported globally, finding a median degradation rate of 0.5% per year. Finally, it provides a detailed bibliography of degradation rates partitioned by technology and location.
This document provides an introduction and overview to the Blogger for Beginners guide. It summarizes the guide's contents and structure. The guide is divided into 10 chapters that will help new users get started with Blogger, write blog posts, customize their blog, add content and widgets, configure comments and feeds, publish posts, and learn more about using Blogger. It aims to explain the key Blogger features and functionality in an easy-to-follow manner through step-by-step instructions and screenshots.
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently.
Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
https://www.n-denkei.com/singapore/inquiry/
Using Design of Experiments Approach to analysis Factors Effecting on the PV ...ijtsrd
Many factors affect the performance of a PV module. In this experiment, we will use the factorial experimental design method to investigate these factors. Several factors are studied in this experiment such as phase change martial type, PCM thickness, fin length thickness, fin count and the wind speed. A factorial design is often used by scientists wishing to understand the effect of two or more independent variables upon a single dependent variable so applying factorial design in PV parameters will give us the most significant parameter on the temperature of the cells. The statistical results showed that the most significant factors affected on the temperature of the cells are PCM thickness and wind speed. Malik Al-Abed Allah | Mahdy Migdady "Using Design of Experiments Approach to analysis Factors Effecting on the PV Cells" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-5 , August 2020, URL: https://www.ijtsrd.com/papers/ijtsrd33065.pdf Paper Url :https://www.ijtsrd.com/engineering/mechanical-engineering/33065/using-design-of-experiments-approach-to-analysis-factors-effecting-on-the-pv-cells/malik-alabed-allah
IRJET - Effects of Temperature and Dust on the Behavior of Photovoltaic SystemsIRJET Journal
This document summarizes a study on the effects of temperature and dust on the performance of photovoltaic systems. Three photovoltaic systems were tested - one with an automatic cooling and cleaning system to maintain the module temperature at 40°C, one with clean modules but no cooling, and one with dusty modules. Measurements of voltage, current, power and temperatures were taken every 10 minutes over 5 hours. The results showed that maintaining the module temperature at 40°C using the cooling system increased energy generation by 26.17% compared to the non-cooled clean module, and improved performance compared to the dusty module.
The document analyzes various factors that affect the performance of photovoltaic (PV) systems. It discusses factors experimentally shown to influence PV module performance such as cable thickness, temperature, shadows, dust particles, charge controllers, and solar cell IV characteristics. It also discusses factors theoretically shown to affect performance such as environmental and operating conditions, solar radiation, spectrum effects, degradation, air mass flow, maximum power point tracking, inverter efficiency, and battery efficiency. The document presents experimental results measuring the effects of these factors on voltage, current, and output power of a PV system over time. It concludes that PV module performance depends on environmental conditions like temperature, irradiation, dust, and shadows.
An optimum location of on-grid bifacial based photovoltaic system in Iraq IJECEIAES
Bifacial photovoltaic (PV) module can gain 30% more energy compared to monofacial if a suitable location were chosen. Iraq (a Middle East country) has a variable irradiation level according to its geographic coordinates, thus, the performance of PV systems differs. This paper an array (17 series, 13 parallel) was chosen to produce 100 kWp for an on-grid PV system. It investigates the PV system in three cities in Iraq (Mosul, Baghdad, and Basrah). Effect of albedo factor, high and pitch of the bifacial module on energy yield have been studied using PVsyst (software). It has been found that the effect is less for a pitch greater than 6 m. The energy gained from bifacial and monofacial PV system module in these cities shows that Mosul is the most suitable for installing both PV systems followed by Baghdad and lastly Basrah. However, in Basrah, the bifacial gain is 12% higher in the energy than monofacial as irradiation there is higher than the other locations, especially for elevation above 1.5 m. Moreover, the cost of bifacial array is 7.23% higher than monofacial, but this additional cost is acceptable since the bifacial gain is about 11.3% higher energy compared to the monofacial.
This document summarizes photovoltaic degradation rates reported in published literature from field testing over the last 40 years. It begins with a brief historical outline of early photovoltaic development and field testing in the US, Europe, Japan, and Australia. The document then analyzes nearly 2,000 degradation rates reported globally, finding a median degradation rate of 0.5% per year. Finally, it provides a detailed bibliography of degradation rates partitioned by technology and location.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
This document evaluates the performance of a commercially used polycrystalline solar photovoltaic module in Maiduguri, Nigeria. A model of the PV module was implemented using MATLAB with daily temperature and solar irradiance data from Maiduguri over one year. Simulation results showed that power generated varied with seasons, with more power in the dry season compared to the rainy season. The sunniest month of April generated the maximum power of 315W, the manufacturer's specified maximum, while the least sunny month of August generated less power. The module performed well under the climatic conditions in Maiduguri.
This document describes a numerical analysis to determine reliable parameters for the one-diode model of perovskite solar cells. 11 perovskite solar cells with efficiencies ranging from 4.6-12.2% were fabricated and characterized. A genetic algorithm combined with the Nelder-Mead method was used to minimize errors between measured I-V curves and the one-diode model, estimating photo-generated current, diode saturation current, ideality factor, shunt and series resistances. A sensitivity analysis of errors showed the estimated parameters were reliable and related to low errors. The analysis found the one-diode model suitable for modeling perovskite solar cells and ideality factors were typically around 2 for
03 partial discharge theory cutler-hammerprasadkappala
This document discusses partial discharge theory and its applications for monitoring electrical systems. Partial discharge monitoring is an effective online predictive maintenance tool for motors, generators, and other electrical equipment operating at 4160 volts or above. Understanding partial discharge theory and how it relates to early detection of insulation deterioration is important for properly evaluating this technique. The document presents simplified models of partial discharge voids and insulation systems to promote understanding of partial discharge technology.
This document summarizes an article that reports on developing an automatic active cooling system for a solar panel with real-time energy monitoring using Internet of Things (IoT) technology. The system aims to improve solar panel efficiency by maintaining optimal operating temperature through active cooling. It consists of sensors to measure temperature, light intensity and energy output, a microcontroller to control the cooling system, and an IoT interface to monitor the system remotely. Experimental results show that active cooling increases the solar panel's average output voltage, current and power by lowering its surface temperature compared to passive cooling.
Core Objective 1: Highlights from the Central Data ResourceAnubhav Jain
The Central Data Resource develops and disseminates solar-related data, tools, and software. It hosts a central data hub that securely stores both private and public data from DuraMat projects. It also develops open-source software libraries that apply data analytics to solve module reliability challenges. The data hub currently has over 60 projects, 128 datasets including 70 public datasets, and over 2000 files and resources accessible to its 137 users.
This study examines the impact of four environmental factors - dust accumulation, water droplets, bird droppings, and partial shading conditions - on photovoltaic (PV) system performance. The results show that dust accumulation, shading, and bird fouling significantly reduce PV current, voltage, and harvested energy. Shading had the strongest negative effect, with power reduction of 33.7-92.6% depending on the shaded area. However, water droplets decreased PV panel temperature and slightly increased power output. Dust reduced power by 8.8% and efficiency by 11.86%. Bird fouling reduced performance by around 7.4%. The study provides quantitative analysis of how each factor individually affects key PV parameters and overall system
This study examines the impact of four environmental factors - dust accumulation, water droplets, bird droppings, and partial shading conditions - on photovoltaic (PV) system performance. The results show that dust accumulation, shading, and bird fouling significantly reduce PV current, voltage, and harvested energy. Shading had the strongest negative effect, with power reduction of 33.7-92.6% depending on the shaded area. However, water droplets decreased PV panel temperature and slightly increased power output. Dust reduced power by 8.8% and efficiency by 11.86%. Bird fouling reduced performance by around 7.4%. The study provides quantitative analysis of how each factor individually affects key PV parameters and overall system
This study investigates experimentally the performance of two-dimensional solar tracking systems with reflector using commercial silicon based photovoltaic module, with open and closed loop control systems. Different reflector materials were also investigated. The experiments were performed at the Hashemite University campus in Zarqa at a latitude of 32⁰, in February and March. Photovoltaic output power and performance were analyzed. It was found that the modified photovoltaic module with mirror reflector generated the highest value of power, while the temperature reached a maximum value of 53 ̊ C. The modified module suggested in this study produced 5% more PV power than the two-dimensional solar tracking systems without reflector and produced 12.5% more PV power than the fixed PV module with 26⁰ tilt angle.
This document summarizes a study on how cathode composition influences the lifetime of organic photovoltaic cells. The study found that cells using a Ca/Ag cathode reached operational lifetimes of 2400 hours under standard sunlight illumination at 25°C, while cells with Al or LiF/Al cathodes degraded much more quickly. At an accelerated aging temperature of 70°C, the efficiency of cells with a Ca/Ag cathode remained over 1% after 600 hours, whereas the performance of cells with Al or LiF/Al cathodes dropped significantly over that time period. The results suggest that cathode composition plays a key role in the stability and longevity of organic solar cells.
A Framework For Epbt Calculation Of Roof Mounted...Lindsey Jones
This document discusses photovoltaic (PV) materials used in solar cells. It begins by noting that solar energy is one of the most widely used energy sources and that humans have developed technologies to capture solar energy for applications like cooking, heating, and powering devices. PV cells are then introduced as devices that convert solar energy into electrical energy. The essay aims to discuss PV materials and drive down production costs to make solar energy more affordable and widespread. Lowering costs is important as solar energy is a renewable source that could become a primary source of electricity.
Design of The Cooling System for Optimizing the Performance of Solar PanelIRJET Journal
This document describes the design and testing of three solar panel cooling systems. The cooling systems included two passive systems, one using an acrylic tank and the other using copper heat pipes and an aluminum heat sink. The third was an active water cooling system that pumped water over the solar panel surface. Experimental results showed that the water cooling system maintained the lowest solar panel temperatures, with panel temperatures around 60°C compared to 70°C without cooling. Cooling the panels in this way improved their electrical output and efficiency by reducing thermal losses at high temperatures.
effect of environmental variables on photovoltaic performance based on experi...IJCMESJOURNAL
This paper investigated the effect of environment variables on Photovoltaic PV performance. It is surely understood that local climate can dramatically affect the power generation from a PV system. The most obvious components are the solar radiation hitting the panels, air temperature, humidity and wind speed. The local climatic conditions and precipitation influence the extent to which the panels get to be dusty or polluted, which affects the electrical power generation. The high air temperature caused a reduction in the PV panel output power rated from 1.85 to 20.22%, as well as, increased relative humidity where the largest decline recorded was 32.24%. The wind has a cooling effect on the PV panel that limits the power reduction due to increased solar radiation or panel back temperature. Besides, the wind blows away the accumulated dust that enhances the resulted PV panel power.
SunPower modules are designed to have a useful life of over 40 years, defined as 99% of modules producing at least 70% of their original power output. Experimental data from accelerated lifetime tests show that SunPower modules experience much less degradation compared to conventional modules under heat, humidity, and thermal cycling stresses. This is due to design differences in SunPower modules like the use of n-type silicon cells and a tin-coated copper foundation that provide robustness against real-world stresses over decades of use. SunPower's physics-based degradation models also match well with field data and support a 40-year useful lifetime for their modules.
Technical and Economic Performance of 1MW Grid-connected PV system in Saudi A...IJERA Editor
In this paper, a feasibility study has been done utilizing real time solar irradiance data for a 1MW grid-connected PV system in Qassim region in the middle of Saudi Arabia. The analysis has been done using both technical and economic indicators. Technical performance indicators are; Yield Factor, Capacity Factor and Performance Ratio. Economic indicators are; Levelized cost of energy and simple payback time. The simulation results show high energy productivity, and both technical and economic indicators are high compared with similar systems in different countries. Also, the greenhouse gas emission reduction has been estimated. The prices of PV modules and balance of system components are up to date. The analysis results proved the viability of the proposed system supposing there is no any governmental incentives or grants which could make big difference.
This document describes the design and simulation of a hybrid photovoltaic (PV)-fuel cell power generation system for remote areas. The system uses a PV array for power production, an electrolyzer to generate hydrogen from water using the PV output, a hydrogen storage tank, and a proton exchange membrane fuel cell stack. A controller ensures continuous power supply to the load by switching between the PV array and fuel cell based on available solar power. Simulation results show the system can provide stable power through variations in solar insolation by storing excess PV power as hydrogen for fuel cell use when sunlight is low.
Performance of 400 kV line insulators under pollution | PDF | DOC | PPTSeminar Links
Visit https://seminarlinks.blogspot.com to download.
Outdoor insulators are subjected to nature Polluted environmental contaminants, which may include sea salt, cement dust, fly ash, birds droppings, industrial emissions etc. deposit on their surface With the increasing industrialization not only the degree of pollution but also the type of pollution has an effect on the performance of the insulators.
Photovoltaic solar farm: earthing system design for cost reduction and syste...IJECEIAES
The increasing demand for green sustainable energy source led to a worldwide increase in the installation of large scale photovoltaic (PV) farms. To ensure the PV farms compliance with safety and operational guidelines, earthing systems are essential component of the design. An adequate earthing system for low, medium, and high voltage areas of the PV farm ensures energy under fault condition and system malfunction are absorbed without exceeding the desirable limits. The work in this paper captures the soil resistivity and the earthing system requirements for each voltage level. The paper highlights the boundaries for combined or separate earthing system between low, medium and high voltage. Furthermore, the works focus on the system cost and maintenance without jeopardizing system integrities and safety compliance. Case study is also included.
A Comprehensive Analysis of Partial Shading Effect on Output Parameters of a ...IJECEIAES
One of the issues of grid-connected photovoltaic systems is the effect of the partial shading on the key parameters and performance of the system. In practice, a share of the entire PV panel may shadded because of the various reasons, inevitably. In this case, the key parameters of the system output are affected with respect to the shading extent and paradigm. In this paper, the effects of the various partial shading patterns on the ouput of the system are examined. This is performed by deriving relevant equations and appropriate modeling of the system and defining different scenarios. The analysis on the system performance is carried out on the dominant output parameters including panel voltage, panel power, and total harmonic distortion (THD) of the inverter. Also, the study considers the effect of using bypass diodes in the panels or not. Addintionally, to compare derived conclusions, the study is implementd on a practical system. The set up is made up of a 7-level multilevel inverter, a Z-source converter, and 1 kW lateral circuitry. The real world test results of the study demonstrate a negligible deviation compared to the simulation results.
THERMAL FAULT DETECTION SYSTEM FOR PV SOLAR MODULESelelijjournal
This document discusses a thermal fault detection system for PV solar modules. The system uses a wireless robotic vehicle with a thermal camera to detect faults in solar panels. Images of a test PV panel were taken under normal and faulty conditions. When a solder connection was broken, the panel's output decreased by 17.5% and the thermal camera detected a difference in shape compared to properly working cells. The study shows thermal monitoring can effectively detect faults and is more economical than traditional visual inspection methods for large solar plants.
The document discusses proper earthing and grounding practices for electrical systems, noting that earthing works like a drainage system to dissipate fault currents and prevent voltage build up, and that using a mesh of conductors increases the rate of dissipation. It also highlights the importance of minimizing impedance in earthing paths to reduce noise currents, and providing separate earthing of shields for data cables to prevent noise infiltration.
The document discusses earthing, grounding, and bonding issues in a photovoltaic plant in the UK from 2014-2015. Measurements found increased leakage currents through cabling from the transformer station. Implemented solutions included improving the earthing panel and connections to decrease values. Proper grounding of equipment throughout the plant is needed to prevent isolation faults and fires. Additional earthing rods or a triangular configuration may be needed if single rods do not sufficiently reduce values.
More Related Content
Similar to Pid-degradation of solarcells- solon in englisch
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
This document evaluates the performance of a commercially used polycrystalline solar photovoltaic module in Maiduguri, Nigeria. A model of the PV module was implemented using MATLAB with daily temperature and solar irradiance data from Maiduguri over one year. Simulation results showed that power generated varied with seasons, with more power in the dry season compared to the rainy season. The sunniest month of April generated the maximum power of 315W, the manufacturer's specified maximum, while the least sunny month of August generated less power. The module performed well under the climatic conditions in Maiduguri.
This document describes a numerical analysis to determine reliable parameters for the one-diode model of perovskite solar cells. 11 perovskite solar cells with efficiencies ranging from 4.6-12.2% were fabricated and characterized. A genetic algorithm combined with the Nelder-Mead method was used to minimize errors between measured I-V curves and the one-diode model, estimating photo-generated current, diode saturation current, ideality factor, shunt and series resistances. A sensitivity analysis of errors showed the estimated parameters were reliable and related to low errors. The analysis found the one-diode model suitable for modeling perovskite solar cells and ideality factors were typically around 2 for
03 partial discharge theory cutler-hammerprasadkappala
This document discusses partial discharge theory and its applications for monitoring electrical systems. Partial discharge monitoring is an effective online predictive maintenance tool for motors, generators, and other electrical equipment operating at 4160 volts or above. Understanding partial discharge theory and how it relates to early detection of insulation deterioration is important for properly evaluating this technique. The document presents simplified models of partial discharge voids and insulation systems to promote understanding of partial discharge technology.
This document summarizes an article that reports on developing an automatic active cooling system for a solar panel with real-time energy monitoring using Internet of Things (IoT) technology. The system aims to improve solar panel efficiency by maintaining optimal operating temperature through active cooling. It consists of sensors to measure temperature, light intensity and energy output, a microcontroller to control the cooling system, and an IoT interface to monitor the system remotely. Experimental results show that active cooling increases the solar panel's average output voltage, current and power by lowering its surface temperature compared to passive cooling.
Core Objective 1: Highlights from the Central Data ResourceAnubhav Jain
The Central Data Resource develops and disseminates solar-related data, tools, and software. It hosts a central data hub that securely stores both private and public data from DuraMat projects. It also develops open-source software libraries that apply data analytics to solve module reliability challenges. The data hub currently has over 60 projects, 128 datasets including 70 public datasets, and over 2000 files and resources accessible to its 137 users.
This study examines the impact of four environmental factors - dust accumulation, water droplets, bird droppings, and partial shading conditions - on photovoltaic (PV) system performance. The results show that dust accumulation, shading, and bird fouling significantly reduce PV current, voltage, and harvested energy. Shading had the strongest negative effect, with power reduction of 33.7-92.6% depending on the shaded area. However, water droplets decreased PV panel temperature and slightly increased power output. Dust reduced power by 8.8% and efficiency by 11.86%. Bird fouling reduced performance by around 7.4%. The study provides quantitative analysis of how each factor individually affects key PV parameters and overall system
This study examines the impact of four environmental factors - dust accumulation, water droplets, bird droppings, and partial shading conditions - on photovoltaic (PV) system performance. The results show that dust accumulation, shading, and bird fouling significantly reduce PV current, voltage, and harvested energy. Shading had the strongest negative effect, with power reduction of 33.7-92.6% depending on the shaded area. However, water droplets decreased PV panel temperature and slightly increased power output. Dust reduced power by 8.8% and efficiency by 11.86%. Bird fouling reduced performance by around 7.4%. The study provides quantitative analysis of how each factor individually affects key PV parameters and overall system
This study investigates experimentally the performance of two-dimensional solar tracking systems with reflector using commercial silicon based photovoltaic module, with open and closed loop control systems. Different reflector materials were also investigated. The experiments were performed at the Hashemite University campus in Zarqa at a latitude of 32⁰, in February and March. Photovoltaic output power and performance were analyzed. It was found that the modified photovoltaic module with mirror reflector generated the highest value of power, while the temperature reached a maximum value of 53 ̊ C. The modified module suggested in this study produced 5% more PV power than the two-dimensional solar tracking systems without reflector and produced 12.5% more PV power than the fixed PV module with 26⁰ tilt angle.
This document summarizes a study on how cathode composition influences the lifetime of organic photovoltaic cells. The study found that cells using a Ca/Ag cathode reached operational lifetimes of 2400 hours under standard sunlight illumination at 25°C, while cells with Al or LiF/Al cathodes degraded much more quickly. At an accelerated aging temperature of 70°C, the efficiency of cells with a Ca/Ag cathode remained over 1% after 600 hours, whereas the performance of cells with Al or LiF/Al cathodes dropped significantly over that time period. The results suggest that cathode composition plays a key role in the stability and longevity of organic solar cells.
A Framework For Epbt Calculation Of Roof Mounted...Lindsey Jones
This document discusses photovoltaic (PV) materials used in solar cells. It begins by noting that solar energy is one of the most widely used energy sources and that humans have developed technologies to capture solar energy for applications like cooking, heating, and powering devices. PV cells are then introduced as devices that convert solar energy into electrical energy. The essay aims to discuss PV materials and drive down production costs to make solar energy more affordable and widespread. Lowering costs is important as solar energy is a renewable source that could become a primary source of electricity.
Design of The Cooling System for Optimizing the Performance of Solar PanelIRJET Journal
This document describes the design and testing of three solar panel cooling systems. The cooling systems included two passive systems, one using an acrylic tank and the other using copper heat pipes and an aluminum heat sink. The third was an active water cooling system that pumped water over the solar panel surface. Experimental results showed that the water cooling system maintained the lowest solar panel temperatures, with panel temperatures around 60°C compared to 70°C without cooling. Cooling the panels in this way improved their electrical output and efficiency by reducing thermal losses at high temperatures.
effect of environmental variables on photovoltaic performance based on experi...IJCMESJOURNAL
This paper investigated the effect of environment variables on Photovoltaic PV performance. It is surely understood that local climate can dramatically affect the power generation from a PV system. The most obvious components are the solar radiation hitting the panels, air temperature, humidity and wind speed. The local climatic conditions and precipitation influence the extent to which the panels get to be dusty or polluted, which affects the electrical power generation. The high air temperature caused a reduction in the PV panel output power rated from 1.85 to 20.22%, as well as, increased relative humidity where the largest decline recorded was 32.24%. The wind has a cooling effect on the PV panel that limits the power reduction due to increased solar radiation or panel back temperature. Besides, the wind blows away the accumulated dust that enhances the resulted PV panel power.
SunPower modules are designed to have a useful life of over 40 years, defined as 99% of modules producing at least 70% of their original power output. Experimental data from accelerated lifetime tests show that SunPower modules experience much less degradation compared to conventional modules under heat, humidity, and thermal cycling stresses. This is due to design differences in SunPower modules like the use of n-type silicon cells and a tin-coated copper foundation that provide robustness against real-world stresses over decades of use. SunPower's physics-based degradation models also match well with field data and support a 40-year useful lifetime for their modules.
Technical and Economic Performance of 1MW Grid-connected PV system in Saudi A...IJERA Editor
In this paper, a feasibility study has been done utilizing real time solar irradiance data for a 1MW grid-connected PV system in Qassim region in the middle of Saudi Arabia. The analysis has been done using both technical and economic indicators. Technical performance indicators are; Yield Factor, Capacity Factor and Performance Ratio. Economic indicators are; Levelized cost of energy and simple payback time. The simulation results show high energy productivity, and both technical and economic indicators are high compared with similar systems in different countries. Also, the greenhouse gas emission reduction has been estimated. The prices of PV modules and balance of system components are up to date. The analysis results proved the viability of the proposed system supposing there is no any governmental incentives or grants which could make big difference.
This document describes the design and simulation of a hybrid photovoltaic (PV)-fuel cell power generation system for remote areas. The system uses a PV array for power production, an electrolyzer to generate hydrogen from water using the PV output, a hydrogen storage tank, and a proton exchange membrane fuel cell stack. A controller ensures continuous power supply to the load by switching between the PV array and fuel cell based on available solar power. Simulation results show the system can provide stable power through variations in solar insolation by storing excess PV power as hydrogen for fuel cell use when sunlight is low.
Performance of 400 kV line insulators under pollution | PDF | DOC | PPTSeminar Links
Visit https://seminarlinks.blogspot.com to download.
Outdoor insulators are subjected to nature Polluted environmental contaminants, which may include sea salt, cement dust, fly ash, birds droppings, industrial emissions etc. deposit on their surface With the increasing industrialization not only the degree of pollution but also the type of pollution has an effect on the performance of the insulators.
Photovoltaic solar farm: earthing system design for cost reduction and syste...IJECEIAES
The increasing demand for green sustainable energy source led to a worldwide increase in the installation of large scale photovoltaic (PV) farms. To ensure the PV farms compliance with safety and operational guidelines, earthing systems are essential component of the design. An adequate earthing system for low, medium, and high voltage areas of the PV farm ensures energy under fault condition and system malfunction are absorbed without exceeding the desirable limits. The work in this paper captures the soil resistivity and the earthing system requirements for each voltage level. The paper highlights the boundaries for combined or separate earthing system between low, medium and high voltage. Furthermore, the works focus on the system cost and maintenance without jeopardizing system integrities and safety compliance. Case study is also included.
A Comprehensive Analysis of Partial Shading Effect on Output Parameters of a ...IJECEIAES
One of the issues of grid-connected photovoltaic systems is the effect of the partial shading on the key parameters and performance of the system. In practice, a share of the entire PV panel may shadded because of the various reasons, inevitably. In this case, the key parameters of the system output are affected with respect to the shading extent and paradigm. In this paper, the effects of the various partial shading patterns on the ouput of the system are examined. This is performed by deriving relevant equations and appropriate modeling of the system and defining different scenarios. The analysis on the system performance is carried out on the dominant output parameters including panel voltage, panel power, and total harmonic distortion (THD) of the inverter. Also, the study considers the effect of using bypass diodes in the panels or not. Addintionally, to compare derived conclusions, the study is implementd on a practical system. The set up is made up of a 7-level multilevel inverter, a Z-source converter, and 1 kW lateral circuitry. The real world test results of the study demonstrate a negligible deviation compared to the simulation results.
THERMAL FAULT DETECTION SYSTEM FOR PV SOLAR MODULESelelijjournal
This document discusses a thermal fault detection system for PV solar modules. The system uses a wireless robotic vehicle with a thermal camera to detect faults in solar panels. Images of a test PV panel were taken under normal and faulty conditions. When a solder connection was broken, the panel's output decreased by 17.5% and the thermal camera detected a difference in shape compared to properly working cells. The study shows thermal monitoring can effectively detect faults and is more economical than traditional visual inspection methods for large solar plants.
Similar to Pid-degradation of solarcells- solon in englisch (20)
The document discusses proper earthing and grounding practices for electrical systems, noting that earthing works like a drainage system to dissipate fault currents and prevent voltage build up, and that using a mesh of conductors increases the rate of dissipation. It also highlights the importance of minimizing impedance in earthing paths to reduce noise currents, and providing separate earthing of shields for data cables to prevent noise infiltration.
The document discusses earthing, grounding, and bonding issues in a photovoltaic plant in the UK from 2014-2015. Measurements found increased leakage currents through cabling from the transformer station. Implemented solutions included improving the earthing panel and connections to decrease values. Proper grounding of equipment throughout the plant is needed to prevent isolation faults and fires. Additional earthing rods or a triangular configuration may be needed if single rods do not sufficiently reduce values.
Andreas Iliou worked as an Operation and Maintenance Engineer for Linder Bad Saulgau from June 2010 to January 2011. He was responsible for the complete solar system installed and made changes that improved the system's efficiency by 46%. His strengths included his system competence and ability to explain how the system works. His supervisor would rehire him and considers him the first specialist to call for any issues with the system.
Conergy is a company that specializes in renewable energy and energy efficiency solutions. They offer products and services related to solar power and energy storage. One of their areas of focus is reducing earth leakage, which refers to unintended electric currents traveling through the ground, in order to improve safety and performance of solar energy systems.
The document outlines steps to take when addressing different claims regarding a photovoltaic system's power production. For claim 1 of less power than expected, it describes checking for shading, mismatches in voltage/current between strings, inverter issues, wiring size and connections. It also details using thermal imaging to check for hotspots indicating cell problems. For claim 2 of less power than previous years, it lists checking for degradation, age-related output decline, and issues like shading, wiring damage or corrosion. For claim 3 of no power during daylight, it provides troubleshooting steps like verifying sunlight, checking switches, breakers, overprotection units, voltages and inverter/tracker functionality.
This document discusses the importance of including measurements during inspections of photovoltaic plants in addition to visual inspections. It notes that visual inspections alone are not sufficient. The document then covers several topics relating to photovoltaic plant inspections including module circuit design and potential shading issues, mismatch effects that can be identified through on-site measurements, hot-spot heating risks from shading, and examining bypass diodes and identifying potential overheating from shading. Case studies and examples from site inspections are provided to illustrate issues found and how measurements aided in their identification and analysis.
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Digital Banking in the Cloud: How Citizens Bank Unlocked Their MainframePrecisely
Inconsistent user experience and siloed data, high costs, and changing customer expectations – Citizens Bank was experiencing these challenges while it was attempting to deliver a superior digital banking experience for its clients. Its core banking applications run on the mainframe and Citizens was using legacy utilities to get the critical mainframe data to feed customer-facing channels, like call centers, web, and mobile. Ultimately, this led to higher operating costs (MIPS), delayed response times, and longer time to market.
Ever-changing customer expectations demand more modern digital experiences, and the bank needed to find a solution that could provide real-time data to its customer channels with low latency and operating costs. Join this session to learn how Citizens is leveraging Precisely to replicate mainframe data to its customer channels and deliver on their “modern digital bank” experiences.
AppSec PNW: Android and iOS Application Security with MobSFAjin Abraham
Mobile Security Framework - MobSF is a free and open source automated mobile application security testing environment designed to help security engineers, researchers, developers, and penetration testers to identify security vulnerabilities, malicious behaviours and privacy concerns in mobile applications using static and dynamic analysis. It supports all the popular mobile application binaries and source code formats built for Android and iOS devices. In addition to automated security assessment, it also offers an interactive testing environment to build and execute scenario based test/fuzz cases against the application.
This talk covers:
Using MobSF for static analysis of mobile applications.
Interactive dynamic security assessment of Android and iOS applications.
Solving Mobile app CTF challenges.
Reverse engineering and runtime analysis of Mobile malware.
How to shift left and integrate MobSF/mobsfscan SAST and DAST in your build pipeline.
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
Discover top-tier mobile app development services, offering innovative solutions for iOS and Android. Enhance your business with custom, user-friendly mobile applications.
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Freshworks Rethinks NoSQL for Rapid Scaling & Cost-EfficiencyScyllaDB
Freshworks creates AI-boosted business software that helps employees work more efficiently and effectively. Managing data across multiple RDBMS and NoSQL databases was already a challenge at their current scale. To prepare for 10X growth, they knew it was time to rethink their database strategy. Learn how they architected a solution that would simplify scaling while keeping costs under control.
zkStudyClub - LatticeFold: A Lattice-based Folding Scheme and its Application...Alex Pruden
Folding is a recent technique for building efficient recursive SNARKs. Several elegant folding protocols have been proposed, such as Nova, Supernova, Hypernova, Protostar, and others. However, all of them rely on an additively homomorphic commitment scheme based on discrete log, and are therefore not post-quantum secure. In this work we present LatticeFold, the first lattice-based folding protocol based on the Module SIS problem. This folding protocol naturally leads to an efficient recursive lattice-based SNARK and an efficient PCD scheme. LatticeFold supports folding low-degree relations, such as R1CS, as well as high-degree relations, such as CCS. The key challenge is to construct a secure folding protocol that works with the Ajtai commitment scheme. The difficulty, is ensuring that extracted witnesses are low norm through many rounds of folding. We present a novel technique using the sumcheck protocol to ensure that extracted witnesses are always low norm no matter how many rounds of folding are used. Our evaluation of the final proof system suggests that it is as performant as Hypernova, while providing post-quantum security.
Paper Link: https://eprint.iacr.org/2024/257
Northern Engraving | Nameplate Manufacturing Process - 2024Northern Engraving
Manufacturing custom quality metal nameplates and badges involves several standard operations. Processes include sheet prep, lithography, screening, coating, punch press and inspection. All decoration is completed in the flat sheet with adhesive and tooling operations following. The possibilities for creating unique durable nameplates are endless. How will you create your brand identity? We can help!
Conversational agents, or chatbots, are increasingly used to access all sorts of services using natural language. While open-domain chatbots - like ChatGPT - can converse on any topic, task-oriented chatbots - the focus of this paper - are designed for specific tasks, like booking a flight, obtaining customer support, or setting an appointment. Like any other software, task-oriented chatbots need to be properly tested, usually by defining and executing test scenarios (i.e., sequences of user-chatbot interactions). However, there is currently a lack of methods to quantify the completeness and strength of such test scenarios, which can lead to low-quality tests, and hence to buggy chatbots.
To fill this gap, we propose adapting mutation testing (MuT) for task-oriented chatbots. To this end, we introduce a set of mutation operators that emulate faults in chatbot designs, an architecture that enables MuT on chatbots built using heterogeneous technologies, and a practical realisation as an Eclipse plugin. Moreover, we evaluate the applicability, effectiveness and efficiency of our approach on open-source chatbots, with promising results.
Taking AI to the Next Level in Manufacturing.pdfssuserfac0301
Read Taking AI to the Next Level in Manufacturing to gain insights on AI adoption in the manufacturing industry, such as:
1. How quickly AI is being implemented in manufacturing.
2. Which barriers stand in the way of AI adoption.
3. How data quality and governance form the backbone of AI.
4. Organizational processes and structures that may inhibit effective AI adoption.
6. Ideas and approaches to help build your organization's AI strategy.
1. Potential Induced Degradation of solar cells and panels
J. Berghold, O. Frank, H. Hoehne, S. Pingel, B. Richardson*, M. Winkler
SOLON SE, Am Studio 16, 12489 Berlin, Germany
* SOLON CORPORATION, 6950 S. Country Club Rd, Tucson, Arizona 85756
ABSTRACT: This paper is focusing on Potential Induced Degradation (PID) of wafer based standard p-type
silicon technology once exposed to external potentials in the field. Test setups are presented for simulation of the
PID in the lab and the influence of cell properties on PID is demonstrated in order to reveal the cell being the
precondition for the PID. However, the solar cells need to be exposed to High Voltage Stress (HVS) caused by a
negative potential relative to ground in order to potentially cause any relevant PID in the field within the 25 years
life time of a solar panel. Besides the key parameters on cell level the paper is also presenting options on panel
and system level in order to prevent PID and therefore to further decrease overall degradation rates of PV
systems. Moreover, the impact of climatic conditions as temperature and humidity on the extent of PID was also
investigated and results are presented in the paper.
Keywords: Degradation, Reliability, Performance
1 INTRODUCTION
Since solar energy generation is getting more and
more important worldwide PV systems and solar parks
are becoming larger consisting of an increasing number
of solar panels being serially interconnected. As a
consequence panels are frequently exposed to high
potentials relative to ground causing High Voltage Stress
(HVS). The potential impact of voltage-biased humidity
exposure of solar panels on long term stability was first
addressed by Hoffman and Ross in 1978 [1] and studies
on the effect of HVS on long term stability of solar
panels depending on the leakage current between solar
cells and ground have been published by NREL in 2005
[2]. However, until now the degradation mechanism
correlated with HVS is not covered by the standard test
procedures listed in IEC 61215 [3].
Depending on the technology different types of Potential
Induced Degradation (PID) occur. The most prominent
case for PID in silicon solar cell technology is
Sunpower’s polarization effect [5] but also other
technologies like a-Si and ribbon silicon have been
reported in the past to be prone to different types of PID
under certain circumstances – either reversible e.g.
polarization or irreversible e.g. electro chemical
corrosion [4]. All known PID effects have one common
characteristic: The degradation is depending on polarity
and level/extent of the potential between cell and ground
which is determined by the actual configuration of the
PV system.
Up to now very different standards exist concerning the
configuration of PV systems. Whereas in Europe PV
systems are certified for voltages up to 1000V, in the US
only 600V are allowed according to NEC. Additionally
there are different regulations in respect to grounding for
different countries and districts. As a consequence the
market access for transformer less inverters technologies
which are very common in Europe is very restricted in
the US since according to NEC solid grounding of the
PV system is still the standard configuration.
However, there are intensive efforts being made in order
to achieve common standards aiming on 1000V as
maximum system voltage and the change of grounding
regulations in the US.
Whereas increasing system voltages and the introduction
of transformer less inverters certainly have a positive
impact on the overall cost efficiency of solar parks, it has
to be put into account that on the same time solar panels
are exposed to increasing HVS within solar systems. So
investigating PID for standard silicon cells can not only
avoid significant power degradation in future systems. It
also can be considered as a clear track for the reduction
of the overall degradation of a panel is therefore a
suitable method in order to expand the life time of a solar
panel even further.
2 OBJECTIVE
The focus of this paper is to present suitable methods
for measuring the PID on panel level as well as showing
possibilities to minimize/avoid PID on cell, panel and
system level.
It shall be demonstrated that although the precondition
for PID can be located at cell level it is the combination
of several parameters such as high potential relative to
ground, panel layout and environmental factors such as
humidity and temperature which are impacting the extent
of power degradation in the field within a panel’s life
time.
3 EXPERIMENTAL
3.1 PID setup for full size panels:
For the simulation of worst case scenarios in the field
two different accelerated test methods were applied in
order to measure PID on panel level.
In figure 1 the general setup is presented showing the
maximum negative voltage relative to ground in the field
being simulated by the application of a potential (1000
V) between the frame and the positive pole of the panel.
In order to increase the leakage current the glass surface
is covered with a constant and continuous water film
realized by a sprinkler. A stack set up was used in order
to study the impact of solar cell properties and panel
layout on the PID stability of up to 16 panels in parallel.
2. Figure 1: Principal test setup for PID measuremnts
For the investigation of the impact of environmental
factors single panels biased according to figure 1 were
placed in the climatic chamber in order to control
humidity and temperature.
3.2 PID setup for single-cell-laminates
For studying the impact of cell properties on PID
single cell laminates (see Figure 2) were built and HVS
was caused by applying - 1000 V to one of the cell poles.
The positive pole of the power supply is connected to a
wet blanket touching the sunny side of the single cell
laminate.
Figure 2: Single-cell-laminates
3.3 Standard test procedure for PID
For characterization of the cells and panels prior and
after the PID test an IV curve as well as a high resolution
electroluminescence (EL) image were captured.
The standard PID test was run for 100h.
To investigate the leakage currents from cell to ground an
ampere meter with data logger was used.
4 BACKGROUND AND APPROACH
In order to better understand the factors impacting
PID the three different levels – cell, panel and system –
were separately investigated.
4.1 Cell level
The cell was found to be the precondition for PID.
Some process steps as well as the quality of the base
material have been identified to significantly contribute
to the extent of PID tendency on cell level. In the result
chapter we take a closer look at the different cell
parameters influencing the PID.
4.2 Panel level
Environmental factors such as humidity and
temperature [2] as well as the panel design are
influencing leakage currents within the panel. The impact
of humidity and temperature is presented in Figure 3.
Figure 3: Dependency of panel leakage current on
temperature and humidity [2]
In case of solar cells being prone to PID high leakage
currents on panel level support PID. The interaction of
the different panel materials is resulting in certain leakage
current paths which are illustrated in Figure 4.
According to Mc Mahon et al [8] the leakage current path
Ip2 is dominating the others.
Higher leakage currents can be caused by water (vapor)
entering the solar panel causing the encapsulation (ENC)
material becoming more conductive.
Figure 4: Leakage currents paths within a solar panel
according to Mc Mahon et al [8]
As a consequence panel design and layout can impact the
leakage currents and therefore play a role for the HV-
durability of panels.
4.3 System level
On system level the potential difference between
ground and cell is the most important factor for PID. The
system voltage depends in first order on the number of
panels serially interconnected and the irradiation and in
second order on the panel temperature.
The final potential of a cell relative to ground is
determined by the grounding configuration. Depending
on the negative, positive or no pole being grounded the
resulting potential the cell is exposed to relative to
ground is either fixed at a certain positive or negative
value or it is not fixed – called floating potential. In the
latter case one part of the string has a negative and the
other a positive potential relative to ground.
3. -1000
-800
-600
-400
-200
0
200
400
600
800
1000
0 5 10 15 20
panel position in string
potential[V]
Floating
PV- grd
PV+ grd
Figure 5: Potential in a string, different grounding
schemes PV+/PV- and no grounding (floating potential)
5 RESULTS
5.1 Cell level
The following two graphs show the evolution of the
IV curve for a solar cell prone to PID and the
corresponding power degradation over time.
Figure 6: Evolution of the IV curve and the
corresponding power with progressing PID
As illustrated in
Table 1 in case of PID shunt resistance as well as the
reverse bias current are affected first followed by FF.
Finally the open circuit voltage decreases reflecting the
junction to be less capable of separating holes and
electrons.
t Uoc Isc P FF
I
(-12V) Rsh
[hr] [V] [A] [W] % [A] [ΩΩΩΩ]
0 0,615 8,240 3,61 71,4 0,21 80,4
20 0,619 8,261 3,66 71,5 0,22 80,4
40 0,615 8,258 3,62 71,3 0,30 51,1
80 0,600 8,109 2,65 54,6 >10 0,5
100 0,572 7,882 1,74 38,7 >10 0,2
rel.
PID -7% -4% -52% -46% -
-
100%
Table 1: Cell IV key parameter change by PID
The Isc is the parameter that is least affected but with
advancing PID Isc also degrades. Depending on the
degree of PID the junction is loosing its blocking
characteristic under reverse bias eventually being short
cutted (ohmic shunt). This phenomenon can be visualized
by EL images taken during a PID test shown in the upper
row of Figure 7. After 40hr local shunts appear along the
edge of the cell that degrade further from diode to ohmic
behavior, as can be seen in the reverse bias image in the
lower row of Figure 7. First shunted areas appear bright
but after further PID evolution these areas do not emit
any more breakdown light [6]. Finally after 100hr both
images are dark because of dominating ohmic shunts.
Figure 7: EL image of a cell during PID test (upper row)
and the corresponding reverse bias (-12V) image (lower
row)
The leakage current within the panel is resulting in a
certain charge concentration above the solar cell in the
ENC. Depending on certain cell properties these charges
might interact with the emitter and the depletion layer
finally causing shunting of the cell. From semiconductor
industry similar effects are known as (time dependent)
dielectric breakdown or surface inversion [5]. The
electric field of these charge carriers is influencing the p-
n-junction in that way that the junction gets more
conductive and the local shunt resistance drops.
There are numerous factors on cell level being important
in respect to PID. In the following we present the
parameters identified to have the most significant impact.
5.1.1 Anti-reflective coating
There are different parameters having an large impact
on PID but the ARC deposition was shown to have a
crucial role in not only influencing but actually
preventing PID on cell level.
In case of typical standard cells ARC is realized by SiNx
applied by a various deposition technologies resulting in
a certain thickness layer thickness and refractive index
(RI) determining the specific properties of the layer.
Figure 8 is illustrating the huge impact of parameter
variations for the ARC deposition on the extent on PID.
It also shows that by using suitable combination of RI
and thickness PID can be completely prevented on cell
level.
4. Figure 8: Dependency of PID on SiN RI and thickness.
For ARC deposition the third parameter having an impact
on PID was found to be the homogeneity of the resulting
SiN layer which was recognized to be clearly different for
various SiN deposition methods.
The observations made for the role of the SiN parameter
concerning PID can be explained by the different
conductivity of the resulting layer for different parameter
settings making trapping of charges more or less likely.
5.1.2 Wafer material
Also the wafer material has been identified to be
another crucial factor regarding PID. The most
significant parameter in this respect is the base resistivity.
As presented in Figure 9 an increasing base resistivity is
resulting in decreasing PID. Higher base resistivity
representing lower base doping leads to a wider depletion
layer at the junction when the emitter doping is held
constant. Accordingly shunting of the junction is less
likely.
Figure 9: Dependency of PID on base resistivity
Within different experiments with cell suppliers where
cells have been produced at constant cell processing
parameters utilizing different wafer suppliers a significant
batch dependence has been found. This could hint on
systematic variation of certain wafer properties relevant
for PID.
Lower quality silicon or comparably high concentration
of crystal defects seem to increase the tendency of PID
but results have to be further verified.
5.1.3 Emitter
Since the emitter process clearly influences the width
of the depletion layer it can definitely be influencing the
probability for shunting the PN-junction and therefore
the tendency for PID. As it can be seen in Figure 10 with
increasing emitter sheet resistivity PID is also increasing.
Figure 10: Dependency of PID on emitter sheet
resistance.
Beside the trend in solar industry to increase the emitter
sheet resistivity for solar cells it can be additionally
increased by new process steps such as emitter back
etching or the introduction of the selective emitter
process.
This example shows that process variations within the
cell process which are thought to be of no relevance for
the later application can lead to degradation when the cell
are exposed to an external potential later in the field.
Since there are many factors on cell level impacting PID
there is no easy distinction between cells more or less
prone to PID just by IV characterization. However, due
to the PID mechanism and the impacting factors
discussed above there are some IV characteristics that
hint on lower PID sensitivity: high shunt resistance and
low reverse bias current. Both parameters are depending
on local defects and base resistivity.
According to our recent results the most effective path for
prevention of PID on cell level is the selection of suitable
parameters (RI and thickness) for ARC deposition.
5.2 Panel level
Since PID is not yet completely excluded on cell
level for all industrial solar cells being produced today it
is certainly worthwhile to take a closer look on the
possibilities to minimize or exclude PID on the panel
level even in case of solar cells prone to PID. In Figure
11 there are shown EL images for a solar panel before
and after the PID test (1000V, 100hr).
According to the image after the test some cells degrade
strongly - finally being short circuited - while others
appear to be stable. Being the cell the origin for PID this
observation can be explained by variation of certain cell
properties relevant for PID as discussed in the chapter
above.
5. Figure 11: EL image of a panel before (upper) and after
(lower) 100hr 1000V PID test
The findings in the EL images do match the observed
power drop of about 30% found after the PID test.
The objective was to investigate how PID on panel level
can be influenced by the panel layout or design. Different
material combinations have been checked in respect to
whether or not the PID is rather supported or suppressed.
It turned out that an important factor is the type of ENC
material since the leakage current can be influenced. In
the following figure the leakage current is shown as a
function of time during a temperature ramp up from -
20°C to 48°C in a humid atmosphere (50% RH).
According to Figure 12 two different encapsulation
materials are causing the peak leakage current to differ by
more than one order of magnitude. The panel can be
described here as a capacitor being charged while the
temperature is rising. When finally the full capacity is
reached the current will drop again.
Figure 12: Leakage current for two panels with different
ENC materials during a temperature ramp from -20°C to
48°C with 1000V applied voltage (RH 50%).
As a consequence of this significant difference in leakage
current the PID results with varying ENC materials differ
strongly as shown in Figure 13.
0,0
20,0
40,0
60,0
80,0
100,0
Material A Material B Material C
relativePIDin%
Figure 13: PID comparison of three different ENC
materials in panels with prone solar cells
Since leakage current on panel level seems to be the key
feature for suppressing PID on panel level it was also
investigated how it is influenced by different
environmental factors such as temperature and moisture.
In the Arrhenius plot in Figure 14 it can be seen both
increasing temperature (T-ramp from -20 °C to 85°C) and
increasing humidity (0% versus 50%) resulting in higher
leakage currents.
Figure 14: Arrhenius plot for the leakage current
depending on temperature and humidity during PID test
(1000V, 100h).
The leakage current for the two test panels in this test
being exposed to different levels of relative humidity
(RH) also corresponds to the different extent of power
degradation (Table 2) obtained for different RH.
Material
combination
Conditions P in%
Material x T= 85°C; RH=0% - 10
Material x T= 85°C; RH=50% - 32
Material x T= 85°C; RH=100% - 99
Table 2: Power drop of three panels (same layout) after
PID test (1000V, 100h, in climatic chamber running a T
ramp -20°C to 85°C) being exposed to different RH.
Even if temperatures and humidity according to Table 2
are meant to be a worst case scenario they show very
impressively the potential impact of environmental
6. factors on PID.
In order to minimize or avoid PID on panel level and
therefore to increase life time and reliability suitable
material combinations and panel design have to be found
to ensure low leakage currents. In this case PID can be
successfully suppressed even for panels with solar cells
prone to PID.
Using PID suppressing encapsulation materials is one of
the layout options in this matter. There are alternative
materials to standard EVA better performing in respect to
PID but other criteria like price, handling, long term
stability issues and availability have to be taken into
account.
5.3 System level
As already mentioned one precondition for PID is the
existence of HVS which is very much influenced by the
specific system configuration – mainly by the kind of
grounding. As already shown in Figure 5 the kind of
grounding determines the potential relative to ground a
panel is exposed to which is also changing with panel
position within a string.
In absence of grounding resulting in a so called floating
potential there is only one part of the string being
exposed to a negative potential causing HVS potentially
turning into PID.
The higher the negative potential the panel is exposed to
the higher the extent of PID as illustrated by
corresponding EL images of a string within a floating
system in Figure 15.
PV- PV+
Figure 15: EL image of a PID affected string of a
floating test system. Only the panels marked by the red
arrow are exposed to a negative potential relative to
ground and therefore prone to PID.
Therefore avoiding negative potential relative to ground
is one way for p-type standard cells on system level in
order to minimize PID independent on cell and panel
properties. This could be achieved by grounding the
negative pole of the system. However, this is not always
possible since in the last few years inverter technologies
have been widely introduced particularly in Europe
which do not allow the grounding of the negative pole
due to the absence of transformers.
Nevertheless, it could be shown that PID cannot only be
prevented on system level by avoiding negative potential
it could also been shown that PID can even be recovered
by reversing the potential having caused the PID. By
showing the reversibility of the PID effect (provided
electrochemical corrosion is excluded) recovery methods
could be developed for affected panels as well as systems
in order to reverse the power loss caused by PID.
The reversibility of PID for solar panels has been
demonstrated in the lab on PID affected panels by
applying the reverse potential in respect to the one
originally causing PID. Whereas for standard like solar
panels the recovery has been done by applying a positive
potential as shown in Figure 16, for other technologies
like Sunpower’s back contact technology it was already
found in 2005 that the polarization effect [4] can be
reversed by applying a negative potential.
Figure 16: Degradation and recovery of panels in the lab
by reversing the applied potential
As a consequence grounding of the positive pole of the
PV system or even a potential shift towards positive
potential as illustrated in Figure 17 can not only prevent
PID on system level it also supports the regeneration of
the panels which is demonstrated in Figure 18.
Figure 17: System configurations supporting the
recovery of PID (solid ground or potential shift) versus
floating potential.
Figure 18: Regeneration of a test string with PID
affected panels by solid grounding of the negative pole
The time necessary for the recovery process depends not
only on the potential but – analog to the degradation
process - also on environmental factors such as humidity
and temperature.
7. 6 SUMMARY AND CONCLUSION
This paper addressed a degradation mechanism called
Potential Induced Degradation (PID) that is believed to
get increasing importance with growing PV systems and
corresponding higher system voltages. Moreover, there
will be an increasing need for further reduction of overall
degradation rates for PV system in order to make PV
systems even more profitable on the long term.
Summarizing all parameters supporting PID it has to be
concluded that there are four main factors to be taken
into account:
First the precondition is a solar cell prone to PID.
Second there has to be a panel layout not systemically
suppressing PID by particularly low leakage currents.
Third the panel has to be exposed to a negative potential
relative to ground.
Fourth the outer conditions have to be additionally
support high leakage currents as comparably high
moisture and temperatures.
Being aware of these main factors it was explained that -
although the origin of PID is on cell level – it can be
minimized or avoided on all levels – system, panel and
cell. The solution on system level is simply the avoidance
of negative potential by choosing suitable grounding of
the system. However, it has been suggested that also high
positive potentials relative to ground can cause
degradation as electrochemical corrosion [9].
This makes a solution on cell or panel level even more
favorable.
On panel level leakage current was identified to be the
main feature to keep as low as possible by a suitable
panel layout and design.
On cell level many parameters influence the PID stability
of solar cells but the most important parameter is found
to be the ARC deposition since by choosing of suitable
parameter settings PID can be banned on cell level. This
would be an enormous advantage since the system
approach by grounding is not always feasible due to the
use of transformer less inverters especially in Europe.
Taking these findings into account long term stability of
solar panels can be significantly improved by adapting
processes on all levels in order to minimize PID and
therefore optimize the energy output of the PV system
over a 25 years life time.
7 OUTLOOK
The scenarios investigated with laboratory and
outdoor tests are simulating worst case conditions with
high humidity and constantly high voltage. At SOLON an
experiment is going on directly comparing laboratory
results with outdoor data at the different SOLON test
sites (Germany, US and Italy) covering also the impact of
different environmental conditions.
8 REFERENCES
[1] Hoffman, A., Ross, R., “Environmental qualification
testing of terrestrial solar cell modules”, Proc. of the 13th
IEEE PV Spec. Conf., Washington, 1978; 835-842.
[2] Del Cueto, J., Trudell, D., Sekulic, W., ”Capabilities
of the High Voltage Stress Test System at the Outdoor
Test Facility”, DOE Solar Energy Technologies Program
Review Meeting, NREL/CP-520-38955, 2005
[3] IEC 61215, “Crystalline Silicon Terrestrial
Photovoltaic Modules – Design Qualification and Type
Approval” edition 2 (2005)
[4] Ross, R., Mon, G., Wen, L., Sugimura, R.,
“Measurement and characterization of voltage- and
current-induced degradation of thin-film photovoltaic
modules”, Solar Cells, Volume 27, Issues 1-4, 1989,
Pages 289-298
[5] Swanson et al., “The surface polarization effect in
high-efficiency silicon solar cells”, 2005
[6] Blish, R., Durrant, N., “Semiconductor device
reliability failure models”, International SEMATECH,
2000
[7] Kasemann et al., “Spatially resolved silicon solar cell
characterization using infrared imaging methods”, 2008
[8] McMahon, T; Jorgensen; G.: “Electrical currents and
adhesion of edge-delete regions of EVA-to-glass module
packaging”, NREL research record, 2001
[9] Azzam, M., “Relative humidity, temperature and
irradiance testing at Mobil Solar Energy Corporation.
NREL/DOE Photovoltaic Performance and Reliability
Workshop, NREL/CP-410-6033 DE94000236, USA,
1993; 153-166.