Motors & controllers
•
0 likes•339 views
The document discusses various types of electric motors and motor controllers. It describes squirrel cage induction motors, different types of motor starters including full voltage non-reversing, reduced voltage autotransformer, and variable frequency drives. It also discusses components of variable frequency drives, features of VFDs, inverter rated motors, overload conditions like single phasing and unbalanced voltage, motor protection types, and motor installation requirements.
Report
Share
Report
Share
Download to read offline
Recommended
Applimotion linear arc_motors_datasheet
The document describes the UTH linear motors produced by Applimotion. The UTH motors combine attributes of the ULT series motors with high performance magnets, providing high output and torque. They are available in diameters from 29mm to 533mm with custom sizes possible. The motors offer a wide range of features like high motor constants, optional windings, sinusoidal torque curves, and optional Hall device feedback or back iron rings. Technical specifications and part numbers for several motor models are provided.
Inertia dynamics wrapspring_dcb2_specsheet
This document provides specifications and part numbers for the J-DCB- series wrap spring clutches. It includes dimensions, torque specifications, part numbers for clockwise and counterclockwise models with different bore sizes and voltages. Exploded diagrams show the replacement parts available, including springs, hubs, stop collars, assemblies, screws and other components. Contact and ordering information is provided for Electromate, which sells and services these clutches.
Ciclotron tip4000 2 h ii
This document contains circuit diagrams for an audio amplifier. It includes diagrams for the preamplifier channels, power supply, protection circuits, and front panel controls and displays. The preamp channels and power supply use common components like transistors, resistors, capacitors, and integrated circuits. The protection circuits monitor for overloads and high temperatures. Front panel circuits control volume, switches and display signals.
Automatic Star Delta Starter using Relay and Adjustable Electronic Timer for ...
This document describes an automatic star-delta starter for a 3-phase induction motor using relays and an adjustable electronic timer. The starter connects the motor windings in either star or delta configuration to reduce starting current. It uses relays controlled by a microcontroller timer to switch between configurations, keeping starting current low by operating in star mode for 3 seconds before switching to delta mode. This protects the motor from high inrush currents while allowing full-load current once started. Experimental results show that lamps connected to represent the motor windings glow dimly in star mode and brightly in delta mode, demonstrating the change in current flow successfully.
File 1389424591
The document describes a 3-phase automatic star-delta starter for an induction motor using relays and adjustable electronic timers. It includes a block diagram of the system and descriptions of the key hardware components including 555 timers, transistors, relays, and the induction motor. The 555 timer IC and components like the BC547 and BC558 transistors are described in detail, along with an overview of how a 3-phase induction motor works through its stator and rotor design. Diagrams are also provided to illustrate the system and component designs.
Soft starters
Soft starters are electronic devices used to control the voltage applied to three-phase induction motors during start up and shut down. This helps reduce mechanical and electrical stresses. Soft starters gradually increase the voltage from 0% to 100% over an adjustable ramp time, controlling current and torque surges. They provide a smooth, stepless acceleration and deceleration compared to direct-on-line starting. Soft starters limit inrush current, reduce voltage dips, and extend the lifetime of motors and mechanical components in applications like pumps, fans, conveyors, and other machinery.
What is-a-circuit-breaker
A circuit breaker is an automatically operated electrical switch that protects electrical circuits from damage caused by overload or short circuit. Unlike a fuse, a circuit breaker can be reset to resume normal operation after tripping. The main parts of a circuit breaker include the actuator lever, actuator mechanism, contacts, terminals, bimetallic strip, calibration screw, and solenoid. Major circuit breaker manufacturers include Schneider, Siemens, GE, and Eaton. MarketElectrical.com carries circuit breakers from all these brands for various applications.
Vehículo conectado y movilidad sostenible
Presentación a cargo de Antonio Rojas, de Grupo Premo, en el 33er Encuentro de la Economía Digital y las Telecomunicaciones organizado por AMETIC y Santander Empresas en colaboración con la UIMP
Recommended
Applimotion linear arc_motors_datasheet
The document describes the UTH linear motors produced by Applimotion. The UTH motors combine attributes of the ULT series motors with high performance magnets, providing high output and torque. They are available in diameters from 29mm to 533mm with custom sizes possible. The motors offer a wide range of features like high motor constants, optional windings, sinusoidal torque curves, and optional Hall device feedback or back iron rings. Technical specifications and part numbers for several motor models are provided.
Inertia dynamics wrapspring_dcb2_specsheet
This document provides specifications and part numbers for the J-DCB- series wrap spring clutches. It includes dimensions, torque specifications, part numbers for clockwise and counterclockwise models with different bore sizes and voltages. Exploded diagrams show the replacement parts available, including springs, hubs, stop collars, assemblies, screws and other components. Contact and ordering information is provided for Electromate, which sells and services these clutches.
Ciclotron tip4000 2 h ii
This document contains circuit diagrams for an audio amplifier. It includes diagrams for the preamplifier channels, power supply, protection circuits, and front panel controls and displays. The preamp channels and power supply use common components like transistors, resistors, capacitors, and integrated circuits. The protection circuits monitor for overloads and high temperatures. Front panel circuits control volume, switches and display signals.
Automatic Star Delta Starter using Relay and Adjustable Electronic Timer for ...
This document describes an automatic star-delta starter for a 3-phase induction motor using relays and an adjustable electronic timer. The starter connects the motor windings in either star or delta configuration to reduce starting current. It uses relays controlled by a microcontroller timer to switch between configurations, keeping starting current low by operating in star mode for 3 seconds before switching to delta mode. This protects the motor from high inrush currents while allowing full-load current once started. Experimental results show that lamps connected to represent the motor windings glow dimly in star mode and brightly in delta mode, demonstrating the change in current flow successfully.
File 1389424591
The document describes a 3-phase automatic star-delta starter for an induction motor using relays and adjustable electronic timers. It includes a block diagram of the system and descriptions of the key hardware components including 555 timers, transistors, relays, and the induction motor. The 555 timer IC and components like the BC547 and BC558 transistors are described in detail, along with an overview of how a 3-phase induction motor works through its stator and rotor design. Diagrams are also provided to illustrate the system and component designs.
Soft starters
Soft starters are electronic devices used to control the voltage applied to three-phase induction motors during start up and shut down. This helps reduce mechanical and electrical stresses. Soft starters gradually increase the voltage from 0% to 100% over an adjustable ramp time, controlling current and torque surges. They provide a smooth, stepless acceleration and deceleration compared to direct-on-line starting. Soft starters limit inrush current, reduce voltage dips, and extend the lifetime of motors and mechanical components in applications like pumps, fans, conveyors, and other machinery.
What is-a-circuit-breaker
A circuit breaker is an automatically operated electrical switch that protects electrical circuits from damage caused by overload or short circuit. Unlike a fuse, a circuit breaker can be reset to resume normal operation after tripping. The main parts of a circuit breaker include the actuator lever, actuator mechanism, contacts, terminals, bimetallic strip, calibration screw, and solenoid. Major circuit breaker manufacturers include Schneider, Siemens, GE, and Eaton. MarketElectrical.com carries circuit breakers from all these brands for various applications.
Vehículo conectado y movilidad sostenible
Presentación a cargo de Antonio Rojas, de Grupo Premo, en el 33er Encuentro de la Economía Digital y las Telecomunicaciones organizado por AMETIC y Santander Empresas en colaboración con la UIMP
Lucthur
Star delta starting involves connecting an induction motor in star configuration during startup for lower starting current, then switching to delta configuration once the motor reaches near normal running speed for higher torque. This allows the motor to start smoothly without drawing excessive current. The motor is connected to star using contactor K1 during startup, then switched to delta using contactor K4 once it reaches 80% of full synchronous speed.
Weg vector-duty-motor-tenv
VECTOR DUTY MOTORS TENV -
Three Phase - Foot Mount - Double C-Face
Designed specifically for inverter operation for applications
requiring 1000:1 constant torque turndown ratio.
* Class F insulation (Impregnation Resin and Magnet wire are class H)
* NEMA design B.
* F1 Mounted (F2 convertible).
* Stainless Steel Nameplate - Laser etched with high contrast background
* Gasketed conduit box
* Class I, Div. 2, Groups A, B, C & D – T3, Class II, Div 2, Groups F & G – T3C
Inverter Rated:
1000 : 1 for constant torque
Features that make a difference:
* Constant torque operation from 0 to base speed (1000:1) on
PWM Vector Drive
* Constant Horsepower operation up to 150% base speed
* Ready for encoder mount
* With thermostats (1 per phase)
* Special nameplate data for easy drive set-up
* Ready for C-face brake, limited to 10 lb-ft braking torque
Inertia dynamics wrapspring_dcb6sm_specsheet
This document provides specifications and part numbers for DCB-6 and DCB-6 SUPER wrap spring clutches. It lists key specifications like maximum speed of 500 RPM, static torque of 500 in-lbs, and positioning accuracy of ±1/2 degrees. It also provides dimensional drawings and descriptions of the clutches and their components. Replacement part numbers and descriptions are given for items like input hubs, output shafts, springs, and other internal parts.
Electronic braking of AC motor
An Electrical braking for all three phase electric motors , removes unnecessary use of mechanical brake lining or mechanical brake units , works with the concept of DC injection braking , also a braking for better safety , application in circular saws , grinding machines, centrifuges, vibrator motors
Tecnotion tb series_specsheet
This document provides specifications for three tubular linear motor models: the TB12, TB15, and TB30. It includes performance data like maximum force, speed, and current as well as electrical properties and mechanical dimensions. Mounting instructions and CAD files can be found online or in the installation manual.
Inertia dynamics wrapspring_dcb6s_specsheet
This document provides specifications and part number information for J-14 wrap spring clutches, models DCB-6 and DCB-6 SUPER. It lists maximum speed, torque, voltage and actuator options for the clutches. The document also provides extensive replacement part number information for components of the clutches. It is intended to support maintenance and repair of the clutch models.
Stepper and hbridgestepper motor as generator hack
1. Stepper motors move in discrete steps and can precisely control movement by counting steps, unlike standard DC motors which rely on continuous rotation.
2. H-bridges are used to power stepper motors by allowing low voltage control logic to drive high voltage to motors in both directions for forward and backward movement.
3. There are different stepper motor modes like full step, half step, and wave that control the number of steps taken per full rotation for finer movement control.
Updated Pv Install Photo Album
This photo album document contains details about 4 different photovoltaic installations including the DC output, module manufacturer and count, inverter manufacturer, and racking system for each. The installations range in DC output from 170.66 kW to 1,114.12 kW and use Ying Li modules mounted on carport, purlin, or sunlink racking systems with inverters from manufacturers like PV Powered, SMA, and Satcon.
Single phase induction motor(eee499.blogspot.com)
This document describes a project to control an induction motor using a microcontroller. It discusses the motor specifications and components used, including a capacitor to provide 90 degrees of phase shift between the main and auxiliary windings. The design uses an inverter to convert DC to AC voltage and vary frequency to control motor speed and direction. Software implements semi-sinusoidal waveforms at 7 kHz to achieve the 90 degree phase shift needed for motor control.
brushless alternator-seminar-ppt 2
This document provides an overview of brushless alternators compared to brushed alternators. It discusses the construction, working principle, losses, and applications of brushless alternators. The key points are:
- Brushless alternators have simplified construction without slip rings or brushes, reducing costs and increasing reliability compared to brushed alternators.
- A brushless alternator contains an exciter alternator and main alternator on the same shaft, with the exciter regulating the output voltage of the main alternator.
- Brushless alternators are now commonly used in automotive and other applications where maintenance-free operation is important.
Micro c lab5(stepper-motor)
The document discusses driving a stepper motor using an 8051 microcontroller. It describes the objectives which are to learn about stepper motors, how to wire one, and interface it with an 8051. It explains that a ULN2003 chip is needed to provide sufficient current from the microcontroller pins to drive the motor. The document outlines how to determine the winding configuration, provides examples of full and half step sequences to rotate the motor clockwise and counterclockwise, and presents the algorithm to implement full stepping. It also discusses step angle and speed control.
17 capability curve
This document discusses synchronous generator capability curves. It provides 3 key points that define the capability curve: (1) the stator copper loss which sets a maximum phase current and apparent power limit, (2) the rotor copper loss which sets a maximum field current and equivalent voltage limit, and (3) the prime mover's power limit which sets the maximum real power limit. The capability curve graphs the generator's ability to supply various combinations of real and reactive power based on these three limits.
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...Edgefxkits & Solutions
The document describes an automatic star-delta starter circuit for induction motors using relays and an adjustable electronic timer. The circuit starts the motor in star configuration using three transformers, rectifiers and a 555 timer circuit to control four relays. After a preset time, the fourth relay switches the motor to delta configuration. It provides basic protection from voltage fluctuations and single phasing faults. The starter reduces starting current compared to direct online starting and is a low-cost solution, though it can be improved further with soft start capabilities.Inertia dynamics sfc650b_specsheet
This document provides specifications for an SFC-650 bearing mounted clutch coupling, including its dimensions, torque and speed ratings, voltage options, and replacement part numbers. The coupling consists of an armature hub, armature, field and rotor assembly, bushings, and other components. Assembly instructions and part ordering information are also included.
Star delta starter
Magnum is one of the best manufacturers of Star Delta Starter which is Semi & Fully automatic 3 Phase
Turbo-Generator
This is a special type of turbo generator which may find its usage in typical chemical plants. Here the steam in turbine comes from sulphuric acid plant.So no need of coal handling plant like in thermal power plants.
Direct Torque Control of Matrix Converter fed BLDC motor
This document describes direct torque control of a brushless DC motor fed by a matrix converter. It begins with background on brushless DC motors and matrix converters. It then discusses an indirect modulation strategy that decouples control of the input current and output voltage. Direct torque control is implemented for the inverter stage alone using a two-phase conduction scheme. Simulation results show the motor achieving the reference speed while maintaining torque within a narrow band despite load variations. The matrix converter provides sinusoidal source currents with lower total harmonic distortion than a conventional AC-DC-AC converter.
The Excitation system by SAI
This PPT is a complete description about the Function,principle,Types and working of Excitation System.
Dc and stepper motor
This document provides an introduction to DC motors and stepper motors. It discusses the basic components and workings of brushed DC motors. Stepper motors are described as electric motors without commutators that are controlled externally through a controller firing opposite coils to attract the rotor. Both unipolar and bipolar stepper motor configurations are examined, along with methods for identifying wires and writing control programs.
Brushless dc electric motor
Brushless DC motors are synchronous motors powered by a DC source via an inverter that produces an AC signal. There are three main types - inrunner, outrunner, and axial flux. Inrunners have the rotor inside the stator, outrunners have the stator inside the rotor, and axial flux uses facing plates. Brushless DC motors are complex but offer benefits over brushed DC motors like higher efficiency, speed, and lifetime. They are well-suited for applications like computer fans and industrial systems where those advantages outweigh their higher cost.
Mitsubishi cnc drive system general catalog (mds d-dm series, mds-d-svj3-spj3...
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.vn
Ht and lt scheme dc system
The document discusses the AC supply system for auxiliary loads in a coal power plant. It describes the various auxiliary systems that require power supply like coal handling, boiler, turbine, cooling water etc. It discusses the classification of auxiliaries based on rating and location to decide the suitable voltage levels. The key voltage levels used are 6.6kV, 3.3kV and 415V. The document also provides details of the switchgear parameters, transformer feeders and motor feeder protection settings. Single line diagrams of various auxiliary systems at different voltage levels are presented.
More Related Content
What's hot
Lucthur
Star delta starting involves connecting an induction motor in star configuration during startup for lower starting current, then switching to delta configuration once the motor reaches near normal running speed for higher torque. This allows the motor to start smoothly without drawing excessive current. The motor is connected to star using contactor K1 during startup, then switched to delta using contactor K4 once it reaches 80% of full synchronous speed.
Weg vector-duty-motor-tenv
VECTOR DUTY MOTORS TENV -
Three Phase - Foot Mount - Double C-Face
Designed specifically for inverter operation for applications
requiring 1000:1 constant torque turndown ratio.
* Class F insulation (Impregnation Resin and Magnet wire are class H)
* NEMA design B.
* F1 Mounted (F2 convertible).
* Stainless Steel Nameplate - Laser etched with high contrast background
* Gasketed conduit box
* Class I, Div. 2, Groups A, B, C & D – T3, Class II, Div 2, Groups F & G – T3C
Inverter Rated:
1000 : 1 for constant torque
Features that make a difference:
* Constant torque operation from 0 to base speed (1000:1) on
PWM Vector Drive
* Constant Horsepower operation up to 150% base speed
* Ready for encoder mount
* With thermostats (1 per phase)
* Special nameplate data for easy drive set-up
* Ready for C-face brake, limited to 10 lb-ft braking torque
Inertia dynamics wrapspring_dcb6sm_specsheet
This document provides specifications and part numbers for DCB-6 and DCB-6 SUPER wrap spring clutches. It lists key specifications like maximum speed of 500 RPM, static torque of 500 in-lbs, and positioning accuracy of ±1/2 degrees. It also provides dimensional drawings and descriptions of the clutches and their components. Replacement part numbers and descriptions are given for items like input hubs, output shafts, springs, and other internal parts.
Electronic braking of AC motor
An Electrical braking for all three phase electric motors , removes unnecessary use of mechanical brake lining or mechanical brake units , works with the concept of DC injection braking , also a braking for better safety , application in circular saws , grinding machines, centrifuges, vibrator motors
Tecnotion tb series_specsheet
This document provides specifications for three tubular linear motor models: the TB12, TB15, and TB30. It includes performance data like maximum force, speed, and current as well as electrical properties and mechanical dimensions. Mounting instructions and CAD files can be found online or in the installation manual.
Inertia dynamics wrapspring_dcb6s_specsheet
This document provides specifications and part number information for J-14 wrap spring clutches, models DCB-6 and DCB-6 SUPER. It lists maximum speed, torque, voltage and actuator options for the clutches. The document also provides extensive replacement part number information for components of the clutches. It is intended to support maintenance and repair of the clutch models.
Stepper and hbridgestepper motor as generator hack
1. Stepper motors move in discrete steps and can precisely control movement by counting steps, unlike standard DC motors which rely on continuous rotation.
2. H-bridges are used to power stepper motors by allowing low voltage control logic to drive high voltage to motors in both directions for forward and backward movement.
3. There are different stepper motor modes like full step, half step, and wave that control the number of steps taken per full rotation for finer movement control.
Updated Pv Install Photo Album
This photo album document contains details about 4 different photovoltaic installations including the DC output, module manufacturer and count, inverter manufacturer, and racking system for each. The installations range in DC output from 170.66 kW to 1,114.12 kW and use Ying Li modules mounted on carport, purlin, or sunlink racking systems with inverters from manufacturers like PV Powered, SMA, and Satcon.
Single phase induction motor(eee499.blogspot.com)
This document describes a project to control an induction motor using a microcontroller. It discusses the motor specifications and components used, including a capacitor to provide 90 degrees of phase shift between the main and auxiliary windings. The design uses an inverter to convert DC to AC voltage and vary frequency to control motor speed and direction. Software implements semi-sinusoidal waveforms at 7 kHz to achieve the 90 degree phase shift needed for motor control.
brushless alternator-seminar-ppt 2
This document provides an overview of brushless alternators compared to brushed alternators. It discusses the construction, working principle, losses, and applications of brushless alternators. The key points are:
- Brushless alternators have simplified construction without slip rings or brushes, reducing costs and increasing reliability compared to brushed alternators.
- A brushless alternator contains an exciter alternator and main alternator on the same shaft, with the exciter regulating the output voltage of the main alternator.
- Brushless alternators are now commonly used in automotive and other applications where maintenance-free operation is important.
Micro c lab5(stepper-motor)
The document discusses driving a stepper motor using an 8051 microcontroller. It describes the objectives which are to learn about stepper motors, how to wire one, and interface it with an 8051. It explains that a ULN2003 chip is needed to provide sufficient current from the microcontroller pins to drive the motor. The document outlines how to determine the winding configuration, provides examples of full and half step sequences to rotate the motor clockwise and counterclockwise, and presents the algorithm to implement full stepping. It also discusses step angle and speed control.
17 capability curve
This document discusses synchronous generator capability curves. It provides 3 key points that define the capability curve: (1) the stator copper loss which sets a maximum phase current and apparent power limit, (2) the rotor copper loss which sets a maximum field current and equivalent voltage limit, and (3) the prime mover's power limit which sets the maximum real power limit. The capability curve graphs the generator's ability to supply various combinations of real and reactive power based on these three limits.
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...Edgefxkits & Solutions
The document describes an automatic star-delta starter circuit for induction motors using relays and an adjustable electronic timer. The circuit starts the motor in star configuration using three transformers, rectifiers and a 555 timer circuit to control four relays. After a preset time, the fourth relay switches the motor to delta configuration. It provides basic protection from voltage fluctuations and single phasing faults. The starter reduces starting current compared to direct online starting and is a low-cost solution, though it can be improved further with soft start capabilities.Inertia dynamics sfc650b_specsheet
This document provides specifications for an SFC-650 bearing mounted clutch coupling, including its dimensions, torque and speed ratings, voltage options, and replacement part numbers. The coupling consists of an armature hub, armature, field and rotor assembly, bushings, and other components. Assembly instructions and part ordering information are also included.
Star delta starter
Magnum is one of the best manufacturers of Star Delta Starter which is Semi & Fully automatic 3 Phase
Turbo-Generator
This is a special type of turbo generator which may find its usage in typical chemical plants. Here the steam in turbine comes from sulphuric acid plant.So no need of coal handling plant like in thermal power plants.
Direct Torque Control of Matrix Converter fed BLDC motor
This document describes direct torque control of a brushless DC motor fed by a matrix converter. It begins with background on brushless DC motors and matrix converters. It then discusses an indirect modulation strategy that decouples control of the input current and output voltage. Direct torque control is implemented for the inverter stage alone using a two-phase conduction scheme. Simulation results show the motor achieving the reference speed while maintaining torque within a narrow band despite load variations. The matrix converter provides sinusoidal source currents with lower total harmonic distortion than a conventional AC-DC-AC converter.
The Excitation system by SAI
This PPT is a complete description about the Function,principle,Types and working of Excitation System.
Dc and stepper motor
This document provides an introduction to DC motors and stepper motors. It discusses the basic components and workings of brushed DC motors. Stepper motors are described as electric motors without commutators that are controlled externally through a controller firing opposite coils to attract the rotor. Both unipolar and bipolar stepper motor configurations are examined, along with methods for identifying wires and writing control programs.
Brushless dc electric motor
Brushless DC motors are synchronous motors powered by a DC source via an inverter that produces an AC signal. There are three main types - inrunner, outrunner, and axial flux. Inrunners have the rotor inside the stator, outrunners have the stator inside the rotor, and axial flux uses facing plates. Brushless DC motors are complex but offer benefits over brushed DC motors like higher efficiency, speed, and lifetime. They are well-suited for applications like computer fans and industrial systems where those advantages outweigh their higher cost.
What's hot (20)
Stepper and hbridgestepper motor as generator hack
Stepper and hbridgestepper motor as generator hack
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...
Automatic Star Delta Starter Using Relays And Adjustable Electronic Timer For...
Direct Torque Control of Matrix Converter fed BLDC motor
Direct Torque Control of Matrix Converter fed BLDC motor
Similar to Motors & controllers
Mitsubishi cnc drive system general catalog (mds d-dm series, mds-d-svj3-spj3...
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.vn
Ht and lt scheme dc system
The document discusses the AC supply system for auxiliary loads in a coal power plant. It describes the various auxiliary systems that require power supply like coal handling, boiler, turbine, cooling water etc. It discusses the classification of auxiliaries based on rating and location to decide the suitable voltage levels. The key voltage levels used are 6.6kV, 3.3kV and 415V. The document also provides details of the switchgear parameters, transformer feeders and motor feeder protection settings. Single line diagrams of various auxiliary systems at different voltage levels are presented.
Cataloge schneider cb motor gv2
Cataloge schneider cb motor gv2Công ty cổ phần OKS | Tổng thầu thi công Nhà máy GMP, Tổng thầu thi công Nhà kho GSP
The document provides information on TeSys rotary handles, circuit breakers, contactors, starters, and overload relays for motor protection and control applications. It includes technical specifications such as current and power ratings for various models of these components suitable for applications from fractional to several hundred horsepower. The table and descriptions allow users to select the appropriate component models based on the requirements of their motor control application.Cataloge schneider contactors LC1 D
Cataloge schneider contactors LC1 DCông ty cổ phần OKS | Tổng thầu thi công Nhà máy GMP, Tổng thầu thi công Nhà kho GSP
The document provides information on various TeSys circuit breakers, contactors, starters, and accessories for motor protection and control applications. It includes technical specifications such as current and voltage ratings for different models as well as recommended combinations of components for various motor power levels. The table and diagrams allow users to select the appropriate TeSys products based on the requirements of their application and motor.Agn102 b
This document provides information about Markon alternators, specifically the BL105 and SL105 models. It describes the basic excitation systems used in these small alternators, which rely on capacitor or slip ring excitation to induce voltage in the rotor. It also discusses considerations for operating these alternators, such as acceptable voltage regulation, testing procedures, and suitability for different load types like motors which can be sensitive to harmonic distortion in the output voltage. Repair instructions are provided for common components like the main rotor diode and varistor.
Uci274 d
www.sunshinemach.com
Key words: diesel generator, diesel gensets, gensets, diesel generator sets, generating sets, енераторы, power plant , электростанции, Дизель-генераторы,aggregaten,électrogènes, grupos electrógenos,grupos electrógenos diesel , Dieselstromerzeuger,Generatoren , Stromerzeuger , aggregate , stromaggregate ,Ηλεκτροπαραγωγά Ζεύγη,ΗΛΕΚΤΡΟΠΑΡΑΓΩΓΑ ΖΕΥΓΗ,Agregaty prądotwórcze , zespoły prądotwórcze,Generatorer,aggregaten , kraftverk., dieselelverk,generatoare de curent , grupuri electrogene , Dízelgenerátorok, Generátorok, máy phát điện diesel, Grupos Electrógenos, GRUPO GERADOR/Cummins,Perkins Deutz,volvo,John Deere, Groupe électrogène, SDMO,Diesel generator China,generator factory,GENELEC, Groupe électrogène - groupe electrogene | le groupe electrogene | groupe electrogene diesel |groupe electrogene insonorise | groupe electrogene gaz, fg wilson, gesan, Himoinsa. PRAMAC, Groupe électrogène, Plantas Eléctricas,
Latin America and the Caribbean ...Countries: Colombia, Dominican Republic, Panama, Venezuela .... Bolivia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, ... Countries: Argentina, Brazil, Dominican Republic, Ecuador, El Salvador, Mexico, Nicaragua, Peru
BASICS+OF+ASM+WITH+VSD.ppt
1. The document discusses the basics of operating an induction motor (ASM) using a variable speed drive (VSD). It describes the functions of the stator and rotor in an induction motor and how speed can be controlled.
2. It provides an overview of different control methods for VSDs including U/f control, vector control, and various field-oriented control approaches.
3. The document outlines techniques for increasing starting torque of an induction motor when using a VSD such as changing the motor configuration, gearing, or connection type. It also lists advantages of VSD operation such as adjustable speed, reduced stress, energy savings, and improved power factor.
Uci274 h
www.sunshinemach.com
Key words: diesel generator, diesel gensets, gensets, diesel generator sets, generating sets, енераторы, power plant , электростанции, Дизель-генераторы,aggregaten,électrogènes, grupos electrógenos,grupos electrógenos diesel , Dieselstromerzeuger,Generatoren , Stromerzeuger , aggregate , stromaggregate ,Ηλεκτροπαραγωγά Ζεύγη,ΗΛΕΚΤΡΟΠΑΡΑΓΩΓΑ ΖΕΥΓΗ,Agregaty prądotwórcze , zespoły prądotwórcze,Generatorer,aggregaten , kraftverk., dieselelverk,generatoare de curent , grupuri electrogene , Dízelgenerátorok, Generátorok, máy phát điện diesel, Grupos Electrógenos, GRUPO GERADOR/Cummins,Perkins Deutz,volvo,John Deere, Groupe électrogène, SDMO,Diesel generator China,generator factory,GENELEC, Groupe électrogène - groupe electrogene | le groupe electrogene | groupe electrogene diesel |groupe electrogene insonorise | groupe electrogene gaz, fg wilson, gesan, Himoinsa. PRAMAC, Groupe électrogène, Plantas Eléctricas,
Latin America and the Caribbean ...Countries: Colombia, Dominican Republic, Panama, Venezuela .... Bolivia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, ... Countries: Argentina, Brazil, Dominican Republic, Ecuador, El Salvador, Mexico, Nicaragua, Peru
Railway locomotive
The document summarizes a seminar presentation on the Railway Locomotive Works in Chittranjan, West Bengal, India. It discusses the history of CLW, the largest electric locomotive manufacturer in Asia, and the types of locomotives produced, including DC motor, induction motor, and static equipment. It also describes testing and assembly sections, the braking system, and concludes that CLW is India's sole electric locomotive manufacturer, producing 225 locomotives per year with equipment supplied by companies like BHEL and ABB.
ABB Switchgear Price list002
MCCB & Switches - Price list of ABB MCCB & Switchgear products. SFU / OT Switch / Fusegear / Switch Fuse Units / ABB Price List / 2018
Katalog product swatech electrica
Swatech Electrica is a general electrical supplier located in Bekasi, Indonesia. It supplies various electrical equipment including:
- Air circuit breakers, miniature circuit breakers, molded case circuit breakers, and residual current circuit breakers.
- Power meters, current transformers, potential transformers, cubicles, transformers, vacuum circuit breakers, contactors, and relays.
- Products from Siemens, Schneider, and other brands for protection, monitoring, control, and power distribution applications.
- Personal protective equipment such as insulating gloves, jackets, boots, and grounding/hot stick tools for working on energized systems.
Hci5 d
www.sunshinemach.com
Key words: diesel generator, diesel gensets, gensets, diesel generator sets, generating sets, енераторы, power plant , электростанции, Дизель-генераторы,aggregaten,électrogènes, grupos electrógenos,grupos electrógenos diesel , Dieselstromerzeuger,Generatoren , Stromerzeuger , aggregate , stromaggregate ,Ηλεκτροπαραγωγά Ζεύγη,ΗΛΕΚΤΡΟΠΑΡΑΓΩΓΑ ΖΕΥΓΗ,Agregaty prądotwórcze , zespoły prądotwórcze,Generatorer,aggregaten , kraftverk., dieselelverk,generatoare de curent , grupuri electrogene , Dízelgenerátorok, Generátorok, máy phát điện diesel, Grupos Electrógenos, GRUPO GERADOR/Cummins,Perkins Deutz,volvo,John Deere, Groupe électrogène, SDMO,Diesel generator China,generator factory,GENELEC, Groupe électrogène - groupe electrogene | le groupe electrogene | groupe electrogene diesel |groupe electrogene insonorise | groupe electrogene gaz, fg wilson, gesan, Himoinsa. PRAMAC, Groupe électrogène, Plantas Eléctricas,
Latin America and the Caribbean ...Countries: Colombia, Dominican Republic, Panama, Venezuela .... Bolivia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, ... Countries: Argentina, Brazil, Dominican Republic, Ecuador, El Salvador, Mexico, Nicaragua, Peru
Fuji sc and sw series contactors
This document provides a selection guide for magnetic contactors and starters in the SC and SW series for open type applications. It includes information on frame sizes, maximum motor capacities, operational currents, auxiliary contact arrangements, standard and optional features, and compatible overload relays for various contactor and starter models. Technical specifications and part numbers are provided for non-reversing contactors and starters in different frame sizes ranging from 0 to N5.
Uci274 f
www.sunshinemach.com
Key words: diesel generator, diesel gensets, gensets, diesel generator sets, generating sets, енераторы, power plant , электростанции, Дизель-генераторы,aggregaten,électrogènes, grupos electrógenos,grupos electrógenos diesel , Dieselstromerzeuger,Generatoren , Stromerzeuger , aggregate , stromaggregate ,Ηλεκτροπαραγωγά Ζεύγη,ΗΛΕΚΤΡΟΠΑΡΑΓΩΓΑ ΖΕΥΓΗ,Agregaty prądotwórcze , zespoły prądotwórcze,Generatorer,aggregaten , kraftverk., dieselelverk,generatoare de curent , grupuri electrogene , Dízelgenerátorok, Generátorok, máy phát điện diesel, Grupos Electrógenos, GRUPO GERADOR/Cummins,Perkins Deutz,volvo,John Deere, Groupe électrogène, SDMO,Diesel generator China,generator factory,GENELEC, Groupe électrogène - groupe electrogene | le groupe electrogene | groupe electrogene diesel |groupe electrogene insonorise | groupe electrogene gaz, fg wilson, gesan, Himoinsa. PRAMAC, Groupe électrogène, Plantas Eléctricas,
Latin America and the Caribbean ...Countries: Colombia, Dominican Republic, Panama, Venezuela .... Bolivia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, ... Countries: Argentina, Brazil, Dominican Republic, Ecuador, El Salvador, Mexico, Nicaragua, Peru
CG (Crompton Greaves) Alternators
CG offers a wide range of low voltage generators including brushless alternators from 5 kVA to 1010 kVA for various applications such as mini-hydro projects, emergency power, telecom towers, and industrial use. Their product lines also include slip ring alternators from 5 kVA to 82.5 kVA for agricultural use as well as alternators for railway and marine applications. CG prides itself on design features like aluminum housings, dual regulation, and MOSFET-based automatic voltage regulators.
Iskra Low Voltage Switchgear
This document provides an index and technical specifications for low voltage switchgear products, including:
- Mini contactors ranging from 0.16-0.22kg for switching electric motors and other loads up to 7.5kW at 230V and 22kW at 690V.
- Contactors relays from 0.16-0.22kg for switching loads up to 2A at 500V and 1A at 690V.
- Motor protection switches from 20-32A for motor circuit protection.
- Miniature circuit breakers from 20-120A for overload and short circuit protection.
- Accessories like auxiliary switch blocks, connection cabinets, and multi-functional
electrical.ppt
This document provides an overview of the electrical system and equipment at the NTPC Lara power plant. It includes a breakdown of the major components in the switchyard, generators, transformers, motors, and switchgears at various voltage levels. Diagrams show the single line diagrams and connections between units, transformers, and switchgears. It also includes specifications of the main equipment such as generators, transformers, circuit breakers and motors.
Uci274 k
This technical data sheet provides specifications and options for an industrial generator. It includes:
1) Details on the voltage regulators, windings, terminals, shaft, insulation, and quality assurance.
2) Ratings for the generator including voltage configurations, kVA ratings, efficiencies, and reactance values.
3) Curves showing efficiency, locked rotor starting, and short circuit performance.
Catalog cs mini contactor-dienhathe.vn
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.vn
Weg crusher-duty-3-phase-motor-usacd0808-brochure-english
The document describes the WEG W22 Crusher Duty three-phase motor. Key features of the motor include increased energy efficiency, reliability for demanding industrial applications, and a longer lifetime through enhancements like upgraded bearings and sealing systems. The motor is designed to reduce maintenance needs and operational costs over its lifetime through energy savings and durability.
Similar to Motors & controllers (20)
Mitsubishi cnc drive system general catalog (mds d-dm series, mds-d-svj3-spj3...
Mitsubishi cnc drive system general catalog (mds d-dm series, mds-d-svj3-spj3...
Weg crusher-duty-3-phase-motor-usacd0808-brochure-english
Weg crusher-duty-3-phase-motor-usacd0808-brochure-english
More from Chad Kurdi, P.E.
Ws003 motors calculations-3 phase 480v induction
This document provides sizing calculations for conductors, controllers, overcurrent protection devices (OCPDs), and disconnects for three 3-phase 480V induction motors rated at 50HP, 60HP, and 75HP that are powered from a single feeder. It calculates the maximum demands for each motor including full load current, locked rotor current, branch circuit conductors, overload protection, controllers, OCPDs, disconnects, feeder conductors, feeder OCPD and disconnect to ensure adequate protection and compliance with National Electrical Code standards.
Ws004 motors calculations-240 v dc
This document summarizes the sizing calculations for conductors, overload protection, controllers, and disconnects for three DC motors powered from a single 240V DC feeder. Motor #1 is 10HP with 38A FLC. Motor #2 is 15HP with 55A FLC. Motor #3 is 20HP with 72A FLC. Calculations are shown for branch circuit conductors, overload protection, controllers according to NEC requirements for each motor. Feeder calculations then size conductors to supply all three motors from a common 250A OCPD and 200A disconnect.
Rp ocpd coordination report 07-23-13
This document contains a time-current curve (TCC) analysis for an industrial project with a reference voltage of 480V. It provides details on the circuit breakers, transformers, and cables in the system, including their ratings, settings, and damage/trip curves. The analysis evaluates the fault duty of a bus fault current at the generator circuit breaker CB-GEN2, which is rated for 2000A and has a short-time rating of 65kA.
Ocpd 07-23-13
Overcurrent protection devices like fuses and circuit breakers are required by the NEC to protect electrical conductors and equipment from excessive currents. Fuses and circuit breakers must have voltage and current ratings matching the circuit, as well as interrupting ratings high enough to safely handle short circuits. Special consideration is given to motor, HVAC, and series-rated circuits to prevent nuisance tripping while still providing adequate protection.
M#3 75 hp 07-25-13
This document contains specifications for circuit breaker CBL-AHU-S3 and motor overload protection for a 75HP air handling unit motor (AHU-S3 M#3). It lists the trip current ratings and thermal overload settings for the circuit breaker and overload protection. It also includes short circuit current ratings and identifies the motor and associated soft starter as a 75HP unit.
M#2 60 hp 07-25-13
This document contains technical specifications for circuit breaker CBL-AHU-S1, including its trip current of 200 amps, thermal curve settings, and instantaneous trip setting of 1000 amps. It also lists specifications for a motor overload relay for a 60HP motor protected by this circuit breaker, including its class 20 thermal settings. Ratings are provided for short circuit currents through the circuit breaker in both 3-phase and single-line-to-ground fault configurations.
M#1 50 hp 07-25-13
This document contains technical specifications for circuit breaker CBL-AHU-S2 and motor overload protection for a 50HP air handling unit motor. It lists the circuit breaker trip settings as 125A with a 5x instantaneous trip of 625A. It also lists the motor overload protection as Class 20 for a 50HP motor served by circuit breaker CB-AHU-S2.
1902 01_SouthSide Works_Sheet - E400 - ELECTRICAL RISER DIAGRAM
This document provides an electrical one-line diagram for a multi-floor commercial building. It shows the locations and ratings of electrical equipment including utility transformers and meters, switchboards, panelboards, generators, and other components. Electrical equipment is shown on each floor and electrical rooms are labeled. Notes provide information on equipment specifications and installation requirements.
More from Chad Kurdi, P.E. (8)
1902 01_SouthSide Works_Sheet - E400 - ELECTRICAL RISER DIAGRAM
1902 01_SouthSide Works_Sheet - E400 - ELECTRICAL RISER DIAGRAM
Recently uploaded
artificial intelligence and data science contents.pptx
What is artificial intelligence? Artificial intelligence is the ability of a computer or computer-controlled robot to perform tasks that are commonly associated with the intellectual processes characteristic of humans, such as the ability to reason.
› ...
Artificial intelligence (AI) | Definitio
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
The Python for beginners. This is an advance computer language.
Python language is very important language at this time. we can easily understand this language by these notes.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building
cnn.pptx Convolutional neural network used for image classication
Convolutional Neural Network used for image classification
Computational Engineering IITH Presentation
This Presentation will give you a brief idea about what Computational Engineering at IIT Hyderabad has to offer.
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Null Bangalore | Pentesters Approach to AWS IAM
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
BRAIN TUMOR DETECTION for seminar ppt.pdf
BRAIN TUMOR DETECTION
AND CLASSIFICATION USING
ARTIFICIAL INTELLIGENCE
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Recently uploaded (20)
artificial intelligence and data science contents.pptx
artificial intelligence and data science contents.pptx
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
The Python for beginners. This is an advance computer language.
The Python for beginners. This is an advance computer language.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
cnn.pptx Convolutional neural network used for image classication
cnn.pptx Convolutional neural network used for image classication
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Engineering Drawings Lecture Detail Drawings 2014.pdf
Engineering Drawings Lecture Detail Drawings 2014.pdf
john krisinger-the science and history of the alcoholic beverage.pptx
john krisinger-the science and history of the alcoholic beverage.pptx