This document provides guidance for teachers on teaching the Exploratory Course on Mechanical Drafting as part of the K to 12 Technology and Livelihood Education curriculum in the Philippines. It includes background information on the overall goals of the K to 12 curriculum and the conceptual framework for teaching TLE courses. It also provides details on the learning modules and lessons, which are designed to teach the basic competencies required for the exploratory courses based on the Training Regulations from the Technical Education and Skills Development Authority. The document describes the parts of each lesson and provides guidance for teachers on preparing and implementing the lessons.
This Teacher’s Guide is intended for you, the TLE teacher, who teaches any of the more than 24 TLE exploratory courses in the Grades 7 and 8 of the K to 12 curriculum.
This Teacher’s Guide is intended for you, the TLE teacher, who teaches any of the more than 24 TLE exploratory courses in the Grades 7 and 8 of the K to 12 curriculum.
EIM 7/8 Lesson 2: Perform Mensuration and CalculationBenandro Palor
LEARNING OUTCOMES:
* explain the basic concept of a system of measurement;
* perform measurement and calculation about electrical works;
* observe safety precautions in handling electrical measuring tools and instruments.
This Lesson Includes:
* System of Measurement
* Basic Unit Conversions
* The Multitester
* Resistance Reading
EIM 7/8 Lesson 2: Perform Mensuration and CalculationBenandro Palor
LEARNING OUTCOMES:
* explain the basic concept of a system of measurement;
* perform measurement and calculation about electrical works;
* observe safety precautions in handling electrical measuring tools and instruments.
This Lesson Includes:
* System of Measurement
* Basic Unit Conversions
* The Multitester
* Resistance Reading
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
Embracing GenAI - A Strategic ImperativePeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Operation “Blue Star” is the only event in the history of Independent India where the state went into war with its own people. Even after about 40 years it is not clear if it was culmination of states anger over people of the region, a political game of power or start of dictatorial chapter in the democratic setup.
The people of Punjab felt alienated from main stream due to denial of their just demands during a long democratic struggle since independence. As it happen all over the word, it led to militant struggle with great loss of lives of military, police and civilian personnel. Killing of Indira Gandhi and massacre of innocent Sikhs in Delhi and other India cities was also associated with this movement.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
2024.06.01 Introducing a competency framework for languag learning materials ...Sandy Millin
http://sandymillin.wordpress.com/iateflwebinar2024
Published classroom materials form the basis of syllabuses, drive teacher professional development, and have a potentially huge influence on learners, teachers and education systems. All teachers also create their own materials, whether a few sentences on a blackboard, a highly-structured fully-realised online course, or anything in between. Despite this, the knowledge and skills needed to create effective language learning materials are rarely part of teacher training, and are mostly learnt by trial and error.
Knowledge and skills frameworks, generally called competency frameworks, for ELT teachers, trainers and managers have existed for a few years now. However, until I created one for my MA dissertation, there wasn’t one drawing together what we need to know and do to be able to effectively produce language learning materials.
This webinar will introduce you to my framework, highlighting the key competencies I identified from my research. It will also show how anybody involved in language teaching (any language, not just English!), teacher training, managing schools or developing language learning materials can benefit from using the framework.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
Francesca Gottschalk - How can education support child empowerment.pptxEduSkills OECD
Francesca Gottschalk from the OECD’s Centre for Educational Research and Innovation presents at the Ask an Expert Webinar: How can education support child empowerment?
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
1. K to 12 BASIC EDUCATION CURRICULUM
Exploratory Course on
MECHANICAL DRAFTING
Republic of the Philippines
DEPARTMENT OF EDCUATION
TECHNOLOGY AND LIVELIHOOD EDUCATION
TEACHER’S GUIDE
2. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 2
TABLE OF CONTENTS
Introduction..................................................................................................................................................................................................................3
Background Information
The Overall Goal of the K to 12 Curriculum .......................................................................................................................................................3
The Conceptual Framework of the Teaching of TLE..........................................................................................................................................3
The TLE Exploratory Courses ...........................................................................................................................................................................5
The Learning Modules and Lessons............................................................................................................................................................................6
New Feature of the Teaching of TLE ...........................................................................................................................................................................6
About the Learning Module
Design of the Module.........................................................................................................................................................................................7
Parts of the Lesson ...........................................................................................................................................................................................8
Reflection ..................................................................................................................................................................................................................11
Curriculum Guide.......................................................................................................................................................................................................12
3. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 3
Teacher’s Guide for TLE Exploratory Course on MECHANICAL DRAFTING
Introduction
This Teacher’s Guide is intended for you, the TLE teacher, who teaches any of the more than 24 TLE exploratory courses in the Grades 7 and 8 of the
K to 12 curriculum. To ensure that you teach the TLE exploratory courses the way they were intended to be taught, you must see the big picture of the K to 12
curriculum and the teaching of TLE. Some background information is necessary.
Background Information
1. The Overall Goal of the K to 12 Curriculum
The K to 12 Curriculum has as its overarching goal the holistic development of every Filipino learner with 21st
century skills who is adequately
prepared for work, entrepreneurship, middle level skills development and higher education. The over arching goal of the K to 12 curriculum, tells
you that the teaching of TLE plays a very important role in the realization of the overall goal of the curriculum. Whether or not the K to 12 graduate
is skilled and ready for work, entrepreneurship and middle skills development depend to a great extent on how effectively you taught TLE.
2. The Conceptual Framework of the Teaching of TLE
Below is a schematic diagram of Technology and Livelihood Education (TLE) framework in general secondary schools. This should guide you in
the teaching of the TLE exploratory courses.
4. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 4
Figure 1.TLE Framework
The diagram shows that Technology and Livelihood Education encompasses the field of Home Economics, Industrial Arts, Agri-Fishery Arts and ICT. The 24
TLE courses can be categorized under any of these fields.
5. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 5
TLE is geared towards the development of technological proficiency and is anchored on knowledge and information, entrepreneurial concepts,
process and delivery, work values and life skills. K to 12 TLE is…
a. one that is built on adequate mastery of knowledge and information, skills and processes, acquisition of right work values and life skills;
b. one that equip students with skills for lifelong learning; and
c. one that is founded on cognitive, behavioral or psychomotor and affective dimensions of human development.
The diagram likewise shows that entrepreneurial concepts also form part of the foundation of quality TLE. It is expected that your TLE students,
after using the Learning Module on Entrepreneurship, imbibe the entrepreneurial spirit and consequently set up their own businesses in the areas
of Agri-Fishery Arts, Industrial Arts, Home Economics, and Information and Communication Technology.
TLE by its nature is dominantly a skill subject and so you must engage your students in an experiential, contextualized, and authentic teaching-
learning process. It is a subject where your students learn best by doing. It is integrative in approach. For instance, it integrates entrepreneurship
with all the areas of TLE. It integrates concepts, skills and values.
3. The TLE Exploratory Courses
TLE in Grades 7 and 8 are exploratory in nature. Your school will choose at least 4 from the list of 24 courses for which 23 Learning Modules have
been prepared. 1
Your school’s choice is determined by the availability of its resources (faculty and facilities) as well as the local needs and
resources of the community.
The 24 TLE exploratory courses focus on four basic common competencies: 1) use and maintenance of tools and equipment; 2) mensuration and
calculation; 3) occupational health and safety procedures, and 4) preparation and interpretation of technical drawing. Why are these competencies
called basic? Because they are competencies that you must acquire in order that you can do higher level competencies. They are also described
common because these are true to all TR-based TLE courses.
1
There are 24 TLE courses but there are only 23 Learning Modules because there is one Learning Module for Tailoring and Dressmaking.
6. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 6
The Learning Modules and Lessons
There is a Learning Module for each exploratory course. If there are 24 exploratory courses then you have 24 Learning Modules in your hands. But
you will use 4 Modules only for the entire year in Grade 7(plus a fifth one on Entrepreneurship) and another 4 Modules in Grade 8 (plus a fifth one on
Entrepreneurship).
Each Learning Module consists of 4 to 5 Lessons2
. The Lessons are focused on the 4 to 5 basic competencies. To avoid meaningless repetition of the
teaching of the 5 common competencies, you have to teach them in the context of the TLE course. For example, you teach “use and maintenance of tools” in
beauty care when you are teaching the course on Beauty Care. You teach the same competencies - use and maintenance of tools-in Horticulture but in the
context of Horticulture and so your tools will not be entirely the same.
New Feature on the Teaching of TLE
What’s new in the teaching of TLE in the K to 12 curriculum? In the K to 12 curriculum, the TLE courses are taught based on the learning
outcomes and performance criteria stated on the Training Regulations(TR)from Technical Education and Skills Development Authority (TESDA). They are TR-
based.
Why is this necessary? To prepare the K to 12 graduate for lucrative work, he/she must earn a National Certificate (NC)I, II or even an NC of higher
level that is required by industries. This he/she earns after passing an assessment given by TESDA.
How can you ensure that the K to 12 high school student (Grade 9 to 12) pass TESDA assessment and obtain an NC? By seeing to it that you
teach the TLE course in accordance with the performance criteria and learning outcomes laid down in the TESDA Training Regulations.
Do the exploratory courses enable the high school student to earn already an NC? Not yet. Completion of the exploratory courses may not yet
qualify a high school student to take an assessment for an NC. Instead, it helps him/her earn a Certificate of Competency (COC) at least in Grade 9 that will
lead eventually him/her to an NC. In short, the COC paves the way to the earning of an NC.
2
Some Learning Modules combined use and maintenance of tools to make one Lesson, so the number of Lessons amount to 4; others made separate Lessons for use of tools and for
maintenance of tools, thus the total is 5 Lessons.
7. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 7
Student’s choice of TLE specialization begins in Grades 9.Afterhaving been exposed to an array of TLE courses during the exploratory phase in the
first two years, the student will be most benefited, if in Grades 10,11, or 12 he/she continues with a TLE course in which he/she already has a COC. In that
way, he/she will get an NC faster.
About the Learning Module
1. Design of the Module
a. The Module is designed to be a teacher-assisted learning kit or a self-learning kit on competencies that a Grade 7 TLE ought to possess. It
explores the course on Aquaculture which helps your student earn a Certificate of Competency in Grade 9which leads to a National Certificate
Level I / II (NCI / II)in Grades 10, 11 or 12.
b. The Learning Module is made up of 4 to 5 Lessons based on the competencies. Each Lesson contains the following:
1) Learning Outcomes
2) Performance Standards
3) Materials/Resources
4) Definition of Terms
5) What Do You Already Know?
6) What Do You Need to Know?
7) How Much Have You Learned?
8) How Do You Apply What You Learned?
9) What Is Your Score?
10) References
There are some TLE Modules which have a section on “How Do You Extend Your Learning?”, This section is meant for enrichment. It is usually
given as an assignment for not everything can be taught and done in the classroom given a limited time.
c. The Self-check can also serve as the posttest of the lesson.
8. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 8
2. Parts of the Lesson. -The following explain the parts of each Lesson and describe what your students’- as well as your tasks are.
Part of the Lesson Students’ Task Teacher’s Task
1. Learning outcomes are what your TLE
student is supposed to know and be able
to do after using the module. Since our
TLE courses are TR-based, all learning
outcomes are lifted from the TESDA TR. In
the Curriculum Guide (the matrix which
contains Content Standard, Performance
Standard, Learning Competencies,
Projects/Activities, Assessment, Duration),
the identified Learning Outcomes are
written in the column of Learning
Competencies.
Students acquaint themselves with the
learning outcomes and performance
standards and make them their personal
goals.
You introduce the learning outcomes to your students
and make sure that they understand them and make
these learning targets their own.
Make these your goals for instruction.
2. Performance Standards are referred to
as “performance criteria” in the TESDA TR.
They are more specific descriptions of the
student’s behavior that serve as evidence
that the expected learning outcomes have
been realized with the expected level of
proficiency or in accordance with
established standards.
The learning outcomes and performance
standards set the direction of your lessons.
Students clearly understand the
performance standards and make them
their own learning goals.
You introduce the performance standards to your
students and make sure that they understand them and
make these performance standards their own.
Let these standards give your lesson its specific direction.
9. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 9
These are what you should teach and, in
turn, what you should assess. They are
identified and are written for you in the
Curriculum Guide.
3. Materials/Resources and References
To teach effectively, you need materials
and references. Materials may include
equipment, hand tools or consumables.
The references are the books, magazines,
articles, websites you yourself and your
students will read or refer to in order to
gain greater understanding of the lesson.
They are either in soft copy or hard copy.
Get to know the materials. They are part of
the Lesson.
By all means, read the references for
lesson mastery.
Prepare the materials you need in advance. For gadget,
tool or equipment, it is always wise to prepare, check and
try them in advance to ensure that they function when
you use them. As the saying goes “forewarned is
forearmed.”
Be resourceful in the preparation of materials. You are
strongly encouraged to use appropriate local materials as
substitute for listed materials that are not available.
For effective teaching, your lesson preparation should
include reading the list of references.
Do not limit yourself to the list of references. If you
discover good reference material/s, add to the list of
references.
Introduce the references to your students. Motivate them
to read these references as they go through the module
for mastery of the lesson.
4. The definition of terms and acronyms
will help you understand the meaning of
key words in your lesson. Defining key
words as they are used in your lesson will
Refer to the definition of terms for greater
understanding of the lesson.
Remind your students to refer to the definition of terms
and acronyms for clearer understanding of the lesson.
10. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 10
ensure that the key terms in your lesson
mean one and the same for everyone in
class and so avoid misunderstanding.
5. The section “What Do You Already
Know” is intended to determine entry
knowledge and skills of your students to
find out if you have to teach the lesson,
teach some parts of the lesson or skip it
entirely because your students already
know it. This is done by way of a pretest.
Take the test honestly.
Check answers against the answer key
provided.
Tell your students to accomplish the pretest. Explain that
the purpose of the pretest is to find out how much they
already know about the lesson in order to determine your
next steps. It is, therefore, necessary that they take the
test honestly, if they want to learn or want to be helped.
Make it clear to them that their scores will not be
recorded for grading purposes and will not be taken
against them.
If you find out that your students already know what you
are about to teach, logic dictates that you do not need to
teach it anymore. You may as well proceed to the next
lesson. If, however, you find out that they do not yet know
what you are about to teach, then by all means teach. Or
if you discover that your students have some erroneous
concepts, then teach and correct their misconceptions.
To know what your students already know and do not yet
know will guide you in adjusting your instruction.
6. “What Do You Need To Know?”- This
section contains one or more Information
Sheets and for some modules an
Operation Sheet. These are important
notes for the TLE student to read after
which he/she is asked to do a Self-check to
Read and understand the Information
Sheet/s and /or Operation Sheet.
Be prepared For a Self-check which serves
as a posttest.
Make sure students are engaged in reading the
Information Sheet/Observation Sheet and in answering
the self-check.
Give assistance to your students where needed.
11. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 11
determine how much he/she has learned.
The self-check functions as a pretest.
Correct answers by referring to the answer
key.
7. “How Do You Apply What You
Learned?” – In this section, you give your
student the opportunity to transfer what
he/she has learned in another activity or in
real life situation. Ideally, this should be a
performance test, what you usually call
practical test. If “the proof of the pudding is
in the eating”, then your student must be
able to apply what she/he learned in real-
life setting or must be able to come up with
a product as an evidence of learning.
Do the Activity.
To determine level of performance, use the
scoring rubrics or check answers against
the answer key, which ever is applicable.
Reflect on assessment results.
Find a way to test real life application of what your
students have learned.
Do not hesitate to use ways of determining how your
students can apply learned facts and concepts which are
more authentic and realistic than that/those given in the
Module.
Reflect on assessment results. Use assessment results
in planning your instruction.
8. How Do You Extend Your Learning? –
As the word implies, this activity is done
outside class hours for enrichment
purposes. This can reinforce lesson
mastery.
Do the task assigned outside class hours. Motivate the students to do the task by making clear what
the enrichment activity is about –why it is given, how it is
done, how it relates to the class lesson .
Reflection
It is a good habit to reflect on your teaching for the day – what went well, what did not go well, why this activity went well with this group, why it didn’t
work well with the other group. What are your realizations? What are lessons learned? Jot them down in your diary. Commit them to your memory. If you do
this consistently, you will find your delivery improve substantially.
12. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 12
Curriculum Guide for the Exploratory Course
For you to get a complete picture of the complete TLE exploratory course on MECHANICAL DRAFTING, you are hereby provided with the Curriculum
Guide on Mechanical Drafting .
Content Standard Performance Standard
Learning
Competencies
Projects/Activities Assessment Duration
LESSON 1: PREPARING DRAFTING MATERIALSAND TOOLS/DRAWING INSTRUMENTS
Demonstrate understanding
of/on:
Types and uses of drafting
materials /tools and
drawing instruments
Proper manipulation of
drafting materials tools and
drawing instruments
1. Drafting materials, Tools and
Drawing instruments are
identified as per job
requirements.
2. Materials and drawing tools
are classified according to their
uses.
LO1.Identify
drafting materials
and tools/drawing
instruments
applicable to a
specific job.
1. Compiling sample pictures
of the different tools and
drawing materials and
classifying them.
2. Demonstrating the proper
manipulation of drawing
instruments.
Performance
test
Written test
6 hours
Procedures in receiving
and storing tools and
materials
Different requisition forms
and procedures
1. Materials and tools are
received and inspected based
on the specified quantity as
requisition.
2. Tools and materials are
checked for damages and
manufacturing defects
LO2. Request,
receive, inspect
and store drafting
materials and
tools.
1. Preparing list of drafting
materials and tools per job
requirement
2. Filling-up different forms
such as requisition slip,
borrower’s slip, etc.
3. Labeling tools and
materials and
storing/safekeeping them
properly.
4. Testing the functionality of
delivered tools and
Performance
test
Written test
3 hours
13. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 13
Content Standard Performance Standard
Learning
Competencies
Projects/Activities Assessment Duration
materials.
LESSON 2: PERFORMINGBASIC MENSURATION AND CALCULATION
Demonstrate understanding
of/on:
Different measuring
instruments and their
application
1. Measuring instruments are
selected and used according
to the level of accuracy
required.
2. Measurements taken are
accurate to the finest
gradation of the selected
measuring instrument.
3. Measuring techniques used
are correct and appropriate to
the instrument used.
LO1. Select and
use
measuring
instruments.
1. Identifying the different
measuring instruments
2. Observing proper use of
measuring instruments
Self-paced
learning
activities
Guided
demonstration
(performance
based)
6 hours
Cleaning and storing
procedure for measuring
instruments
1. Measuring instruments are
cleaned in accordance with
established standards.
2. Measuring instruments are
stored in accordance with
established standards.
LO2. Clean and
store measuring
instruments.
1. Storing/safe keeping
measuring tools properly
Performance test
2 hours
Conversion of fraction to
decimal or decimal to
fraction
1. Conversion results of fraction
to decimal are accurate up to
2 decimal places.
2. Conversion results of decimal
LO3. Convert
fraction to
decimal and
vice versa
1. Solving problems and
exercises correctly in:
a. converting fraction to
decimal or decimal to
Written test 2 hours
14. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 14
Content Standard Performance Standard
Learning
Competencies
Projects/Activities Assessment Duration
to fraction are accurate to the
nearest standard
measurement
fraction
Trade Mathematics and
Measurement
Two system of
measurements
Conversion of units of
linear measurement.
1. English and metric
measurements identified.
2. Conversion of English to
metric system or metric to
English system is performed
according to standard
procedure.
LO4. Convert
English to
metric
measureme
nt system
and vice
versa
1. Solving problems and
exercises correctly.
2. Converting units of linear
measurement.
3. Converting decimal to
fraction
Written test 2 hours
LESSON 3: INTERPRETING WORKING PLANS AND SKETCHES
Demonstrate understanding
of/on:
Alphabet of lines
Line Sketching
Theories and principles of
orthographic projections
Orthographic Projections
Pictorial drawing
More on Oblique Drawing
Scaling
Rules in Dimensioning
Preparation of Working
Plans
Assembly and detailed
drawing
1. Orthographic and pictorial
drawings are interpreted
according to drawing
standards.
2. Assembly and detailed
drawings are interpreted
according to drawing
standards.
LO1.Identify
assembly
and detailed
drawing.
1. Practicing line sketching
2. Sketching sample detail
and assembly drawings
3. Observing drawing
standards
4. Sketching orthographic
views and pictorial views
5. Preparing a working plan
6. Identifying proper line
applications
Written test
Performance
test
13 hours
15. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 15
Content Standard Performance Standard
Learning
Competencies
Projects/Activities Assessment Duration
LESSON 4: APPLYING SAFETY PRACTICES
Demonstrate understanding
of/on:
Occupational safety
standards and enterprise
safety policies.
Practicing Proper
Procedures in using
drafting tools, materials
and instrument
Keeping Workplace Clean
and organized following
5S
Accident Prevention Signs
and Symbols
Hazards in the workplace
Types of workplace
hazards and examples
1. Hazards are identified
correctly in accordance with
OHS procedures.
2. Safety signs and symbols are
identified and adhered to in
accordance with workplace
safety procedures.
LO1. Identifying
hazardous
area
1. Observing safety work
habits in the work place
2. Multimedia presentation
Written test
Performance
test
4 hours
Personal protective
equipment (PPE) for
different drafting
operations
1. Personal protective
clothing/equipment (PPE)
identified per job
requirements.
2. Proper wearing of PPE is
properly observed in
accordance with workplace
safety policies.
LO2. Use personal
protective
clothing and
devices
2. Familiarizing oneself with
the different types and
uses of personal protective
equipment (PPE)
3. Multimedia presentation
Written test
Actual
demonstration
2 hours
40 hours
16. K to 12 TECHNOLOGY AND LIVELIHOOD EDUCATION
INDUSTRIAL ARTS - MECHANICAL DRAFTING
(Exploratory)
**TWG on K to 12 Curriculum Guide – version April 10, 2012 16
“By three methods we may learn wisdom: First, by reflection, which is noblest; second, by imitation, which is
easiest; and third by experience, which is the bitterest.”
- Confucius