This presentation addresses the changes and trends in key standards; factors that influence results and solutions; and increasing lab efficiency and throughput in regards to melt flow, heat deflection temperature (HDT), & impact testing.
Service and Technologies for Process IndustriesJohn Crane
Our world-class rotating equipment technologies, paired with an unmatched breadth of applied engineering expertise, helps plants reduce maintenance costs, slash down time and improve reliability. When it comes to keeping your rotational equipment running 24/7, John Crane’s comprehensive range of products has you covered.
Prospect of non destructive testing and condition monitoring scope in bangladeshFerdous Kabir
Bangladesh is a developing country; industrial development is increasing day by day. If we desire a sustainable industrial development so we should concentrated development of health of our industry.
Non Destructive Testing and Condition Monitoring is the part of Predictive Maintenance (PdM).
Predictive maintenance (PdM) techniques are designed to help determine the condition of in-service equipment in order to predict when maintenance should be performed.
Apply concept and practice of Predictive maintenance (PdM) can be help sustainable development and proper industrial production in Bangladesh.
This presentation addresses the changes and trends in key standards; factors that influence results and solutions; and increasing lab efficiency and throughput in regards to melt flow, heat deflection temperature (HDT), & impact testing.
Service and Technologies for Process IndustriesJohn Crane
Our world-class rotating equipment technologies, paired with an unmatched breadth of applied engineering expertise, helps plants reduce maintenance costs, slash down time and improve reliability. When it comes to keeping your rotational equipment running 24/7, John Crane’s comprehensive range of products has you covered.
Prospect of non destructive testing and condition monitoring scope in bangladeshFerdous Kabir
Bangladesh is a developing country; industrial development is increasing day by day. If we desire a sustainable industrial development so we should concentrated development of health of our industry.
Non Destructive Testing and Condition Monitoring is the part of Predictive Maintenance (PdM).
Predictive maintenance (PdM) techniques are designed to help determine the condition of in-service equipment in order to predict when maintenance should be performed.
Apply concept and practice of Predictive maintenance (PdM) can be help sustainable development and proper industrial production in Bangladesh.
The Model 200 Pneumatic Volume Booster reproduces a pneumatic signal in a 1:1 ratio. It is ideally suited for systems that require input isolation or increased forward flow capacity. This device uses a force balance system to control the movement of the supply and exhaust valves. As a pilot operated regulator design, the M200 handles up to 250 psig, [17.0 BAR], (1700 kPa) supply pressure and provides a flow Ultra high Flow capacity of 1800 SCFM (3058 m3/HR), which equates to a Cv factor of approximately 18 in forward flow mode.
Wika is the leading global manufacturer of pressure and temperature measurement instrumentation, producing more than 43 million pressure gauges, diaphragm seals, pressure transmitters, thermometers and other instruments annually. WIKA’s extensive product line, including mechanical and electronic instruments, provides measurement solutions for any application in a large variety of industries.
The Mark 80 Series Temperature Regulator features the advanced sliding gate seat technology pioneered by Jordan Valve. Using the Jordan Valve sliding gate seat technology, the Mark 80 temperature regulators have the signature straight-through flow, short-stroke that is 1/3 of a globe-style valve, quiet operation and tight shutoff. The Jordan Valve Mark 80 has extended temperature ranges and extremely accurate regulation. The proprietary Jorcote seat material is extremely hard (@RC85) with a low coefficient of friction that delivers outstanding performance and long service life.
Jordan Valve’s unique Seal Welded Actuator (SWA), used in conjunction with Jordan’s sliding gate seat, provides exceptional accuracy and long life in a direct operated industrial temperature regulator. The Jordan Valve Mark 80 is the most accurate and durable industrial temperature regulator available in the market today.
BARTON 7000 Series liquid turbine meters are designed for a broad range of precise liquid measurement applications. Based on more than 40 years of turbine manufacturing experience, this built-to-order series features a range of sizes, materials, bearing systems, and options.
Cold stretching has been in use for more than 30 years, but not under ASME code rules until 2008(Code Case 2596). Cold stretching (or cold working) increases the yield limit of a stainless steel material by work hardening it after all forming and welded steps are complete. A vessel can be cold stretched by over pressurizing it 1.5 to 1.6 times design pressure under careful control of the deformation vs pressure as outlined in VIII-1 App 44. The resulting permanent plastic deformation increases the diameter up to 7% and the volume by 14%.
Tiêu chuẩn ISO 14644 cho phòng sạch phần 3: phòng sạch và các môi trường kiểm soát liên quan. Xem thêm các tài liệu khác trên kênh của Công ty Cổ phần Tư vấn Thiết kế GMP EU
The Model 200 Pneumatic Volume Booster reproduces a pneumatic signal in a 1:1 ratio. It is ideally suited for systems that require input isolation or increased forward flow capacity. This device uses a force balance system to control the movement of the supply and exhaust valves. As a pilot operated regulator design, the M200 handles up to 250 psig, [17.0 BAR], (1700 kPa) supply pressure and provides a flow Ultra high Flow capacity of 1800 SCFM (3058 m3/HR), which equates to a Cv factor of approximately 18 in forward flow mode.
Wika is the leading global manufacturer of pressure and temperature measurement instrumentation, producing more than 43 million pressure gauges, diaphragm seals, pressure transmitters, thermometers and other instruments annually. WIKA’s extensive product line, including mechanical and electronic instruments, provides measurement solutions for any application in a large variety of industries.
The Mark 80 Series Temperature Regulator features the advanced sliding gate seat technology pioneered by Jordan Valve. Using the Jordan Valve sliding gate seat technology, the Mark 80 temperature regulators have the signature straight-through flow, short-stroke that is 1/3 of a globe-style valve, quiet operation and tight shutoff. The Jordan Valve Mark 80 has extended temperature ranges and extremely accurate regulation. The proprietary Jorcote seat material is extremely hard (@RC85) with a low coefficient of friction that delivers outstanding performance and long service life.
Jordan Valve’s unique Seal Welded Actuator (SWA), used in conjunction with Jordan’s sliding gate seat, provides exceptional accuracy and long life in a direct operated industrial temperature regulator. The Jordan Valve Mark 80 is the most accurate and durable industrial temperature regulator available in the market today.
BARTON 7000 Series liquid turbine meters are designed for a broad range of precise liquid measurement applications. Based on more than 40 years of turbine manufacturing experience, this built-to-order series features a range of sizes, materials, bearing systems, and options.
Cold stretching has been in use for more than 30 years, but not under ASME code rules until 2008(Code Case 2596). Cold stretching (or cold working) increases the yield limit of a stainless steel material by work hardening it after all forming and welded steps are complete. A vessel can be cold stretched by over pressurizing it 1.5 to 1.6 times design pressure under careful control of the deformation vs pressure as outlined in VIII-1 App 44. The resulting permanent plastic deformation increases the diameter up to 7% and the volume by 14%.
Tiêu chuẩn ISO 14644 cho phòng sạch phần 3: phòng sạch và các môi trường kiểm soát liên quan. Xem thêm các tài liệu khác trên kênh của Công ty Cổ phần Tư vấn Thiết kế GMP EU
Putting the SPARK into Virtual Training.pptxCynthia Clay
This 60-minute webinar, sponsored by Adobe, was delivered for the Training Mag Network. It explored the five elements of SPARK: Storytelling, Purpose, Action, Relationships, and Kudos. Knowing how to tell a well-structured story is key to building long-term memory. Stating a clear purpose that doesn't take away from the discovery learning process is critical. Ensuring that people move from theory to practical application is imperative. Creating strong social learning is the key to commitment and engagement. Validating and affirming participants' comments is the way to create a positive learning environment.
Attending a job Interview for B1 and B2 Englsih learnersErika906060
It is a sample of an interview for a business english class for pre-intermediate and intermediate english students with emphasis on the speking ability.
Business Valuation Principles for EntrepreneursBen Wann
This insightful presentation is designed to equip entrepreneurs with the essential knowledge and tools needed to accurately value their businesses. Understanding business valuation is crucial for making informed decisions, whether you're seeking investment, planning to sell, or simply want to gauge your company's worth.
Explore our most comprehensive guide on lookback analysis at SafePaaS, covering access governance and how it can transform modern ERP audits. Browse now!
[Note: This is a partial preview. To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
Sustainability has become an increasingly critical topic as the world recognizes the need to protect our planet and its resources for future generations. Sustainability means meeting our current needs without compromising the ability of future generations to meet theirs. It involves long-term planning and consideration of the consequences of our actions. The goal is to create strategies that ensure the long-term viability of People, Planet, and Profit.
Leading companies such as Nike, Toyota, and Siemens are prioritizing sustainable innovation in their business models, setting an example for others to follow. In this Sustainability training presentation, you will learn key concepts, principles, and practices of sustainability applicable across industries. This training aims to create awareness and educate employees, senior executives, consultants, and other key stakeholders, including investors, policymakers, and supply chain partners, on the importance and implementation of sustainability.
LEARNING OBJECTIVES
1. Develop a comprehensive understanding of the fundamental principles and concepts that form the foundation of sustainability within corporate environments.
2. Explore the sustainability implementation model, focusing on effective measures and reporting strategies to track and communicate sustainability efforts.
3. Identify and define best practices and critical success factors essential for achieving sustainability goals within organizations.
CONTENTS
1. Introduction and Key Concepts of Sustainability
2. Principles and Practices of Sustainability
3. Measures and Reporting in Sustainability
4. Sustainability Implementation & Best Practices
To download the complete presentation, visit: https://www.oeconsulting.com.sg/training-presentations
Unveiling the Secrets How Does Generative AI Work.pdfSam H
At its core, generative artificial intelligence relies on the concept of generative models, which serve as engines that churn out entirely new data resembling their training data. It is like a sculptor who has studied so many forms found in nature and then uses this knowledge to create sculptures from his imagination that have never been seen before anywhere else. If taken to cyberspace, gans work almost the same way.
The world of search engine optimization (SEO) is buzzing with discussions after Google confirmed that around 2,500 leaked internal documents related to its Search feature are indeed authentic. The revelation has sparked significant concerns within the SEO community. The leaked documents were initially reported by SEO experts Rand Fishkin and Mike King, igniting widespread analysis and discourse. For More Info:- https://news.arihantwebtech.com/search-disrupted-googles-leaked-documents-rock-the-seo-world/
"𝑩𝑬𝑮𝑼𝑵 𝑾𝑰𝑻𝑯 𝑻𝑱 𝑰𝑺 𝑯𝑨𝑳𝑭 𝑫𝑶𝑵𝑬"
𝐓𝐉 𝐂𝐨𝐦𝐬 (𝐓𝐉 𝐂𝐨𝐦𝐦𝐮𝐧𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬) is a professional event agency that includes experts in the event-organizing market in Vietnam, Korea, and ASEAN countries. We provide unlimited types of events from Music concerts, Fan meetings, and Culture festivals to Corporate events, Internal company events, Golf tournaments, MICE events, and Exhibitions.
𝐓𝐉 𝐂𝐨𝐦𝐬 provides unlimited package services including such as Event organizing, Event planning, Event production, Manpower, PR marketing, Design 2D/3D, VIP protocols, Interpreter agency, etc.
Sports events - Golf competitions/billiards competitions/company sports events: dynamic and challenging
⭐ 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐝 𝐩𝐫𝐨𝐣𝐞𝐜𝐭𝐬:
➢ 2024 BAEKHYUN [Lonsdaleite] IN HO CHI MINH
➢ SUPER JUNIOR-L.S.S. THE SHOW : Th3ee Guys in HO CHI MINH
➢FreenBecky 1st Fan Meeting in Vietnam
➢CHILDREN ART EXHIBITION 2024: BEYOND BARRIERS
➢ WOW K-Music Festival 2023
➢ Winner [CROSS] Tour in HCM
➢ Super Show 9 in HCM with Super Junior
➢ HCMC - Gyeongsangbuk-do Culture and Tourism Festival
➢ Korean Vietnam Partnership - Fair with LG
➢ Korean President visits Samsung Electronics R&D Center
➢ Vietnam Food Expo with Lotte Wellfood
"𝐄𝐯𝐞𝐫𝐲 𝐞𝐯𝐞𝐧𝐭 𝐢𝐬 𝐚 𝐬𝐭𝐨𝐫𝐲, 𝐚 𝐬𝐩𝐞𝐜𝐢𝐚𝐥 𝐣𝐨𝐮𝐫𝐧𝐞𝐲. 𝐖𝐞 𝐚𝐥𝐰𝐚𝐲𝐬 𝐛𝐞𝐥𝐢𝐞𝐯𝐞 𝐭𝐡𝐚𝐭 𝐬𝐡𝐨𝐫𝐭𝐥𝐲 𝐲𝐨𝐮 𝐰𝐢𝐥𝐥 𝐛𝐞 𝐚 𝐩𝐚𝐫𝐭 𝐨𝐟 𝐨𝐮𝐫 𝐬𝐭𝐨𝐫𝐢𝐞𝐬."
Discover the innovative and creative projects that highlight my journey throu...dylandmeas
Discover the innovative and creative projects that highlight my journey through Full Sail University. Below, you’ll find a collection of my work showcasing my skills and expertise in digital marketing, event planning, and media production.
RMD24 | Retail media: hoe zet je dit in als je geen AH of Unilever bent? Heid...BBPMedia1
Grote partijen zijn al een tijdje onderweg met retail media. Ondertussen worden in dit domein ook de kansen zichtbaar voor andere spelers in de markt. Maar met die kansen ontstaan ook vragen: Zelf retail media worden of erop adverteren? In welke fase van de funnel past het en hoe integreer je het in een mediaplan? Wat is nu precies het verschil met marketplaces en Programmatic ads? In dit half uur beslechten we de dilemma's en krijg je antwoorden op wanneer het voor jou tijd is om de volgende stap te zetten.
RMD24 | Retail media: hoe zet je dit in als je geen AH of Unilever bent? Heid...
Iso 8434 5
1. iso-8434 - Part 5
INTERNATIONAL ISO STANDARD 8434-5
First edition 1995-12-01
Metallic tube connections for fluid power
and general use — Part 5:Test methods
for threaded hydraulic fluid power
connections
Reference number ISO 8434-5:1995 (E)
Contents
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 Proof pressure test
6 Failure pressure test (Burst)
7 Cyclic endurance test
8 Vacuum test
9 Overtorque test
10 Identification statement (Reference to this part of ISO 8434)
Annexes
A Test data form
 Applicable tests for various fitting and stud end standards
Ñ Bibliography
ISO 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the
publisher.
file:///C|/$Works/Docs/2/iso-08434-5.htm (1 of 13) [17.03.2003 12:24:48]
2. iso-8434 - Part 5
International Organization for Standardization Case Postale 56 • CH-1211 Geneve 20 •Switzerland
Printed in Switzerland
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies
for voting. Publication as an International Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard ISO 8434-5 was prepared jointly by Technical Committees ISO/TC 5, Ferrous
metal pipes and metallic fittings and ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors
and similar products and components.
These test methods have been included in several International Standards, but because of their generic
application to ports, studs and tube connections for both metric and inch connections, it was agreed that a
separate standard should be established. Additional tests are being considered.
ISO 8434 consists of the following parts, under the general title Metallic tube connections for fluid power
and general use:
— Part 1: 24 degree compression fittings
— Part 2: 37 degree flared fittings
— Part 3: O-ring face seal fittings
— Part 4: 24 degree cone connectors with O-ring weld-on nipples
— Part 5: Test methods for threaded hydraulic fluid power connections
Annex A forms an integral part of this part of ISO 8434.
Annexes  and Ñ are for information only.
file:///C|/$Works/Docs/2/iso-08434-5.htm (2 of 13) [17.03.2003 12:24:48]
3. iso-8434 - Part 5
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit. Components must be designed to meet these requirements under varying
conditions. Testing of components to meet performance requirements provides a basis of assurance for
determining design application and for checking component compliance with the stated requirements.
Metallic tube connections for fluid power
and general use — Part 5:Test methods
for threaded hydraulic fluid power
connections
1 Scope
This part of ISO 8434 specifies uniform methods for the testing and performance evaluation of threaded
metallic tube connections and stud ends of ports for hydraulic fluid power.Tests outlined in this part of
ISO 8434 are independent of each other and document the method to follow for each test; see the
appropriate component International Standard for the test requirements and performance criteria.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of
this part of ISO 8434. At the time of publication, the editions indicated were valid. All standards are
subject to revision, and parties to agreements based on this part of ISO 8434 are encouraged to
investigate the possibility of applying the most recent editions of the standards indicated below.
Members of IEC and ISO maintain registers of currently valid International Standards.
ISO 48:1994, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10
RHD and 100 IRHD).
ISO 3448:1975, Industrial liquid lubricants — ISO viscosity classification — First edition.
file:///C|/$Works/Docs/2/iso-08434-5.htm (3 of 13) [17.03.2003 12:24:48]
4. iso-8434 - Part 5
ISO 3601-3:1987, Fluid systems — Sealing devices — O-rings — Part 3: Quality acceptance criteria.
ISO 5598:1985, Fluid power systems and components — Vocabulary.
ISO 6508:1986, Metallic materials — Hardness test — Rockwell test (scales A-B-C-D-E-F-G-H-K).
ISO 6803:1994, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test
without flexing.
3 Definitions
For the purposes of this part of ISO 8434, the definitions given in ISO 5598 apply.
4 General requirements
4.1 Test samples
All components tested shall be tested in the final form (as the customer receives the part), including
annealing as required for brazing.
4.2 Test temperature
Test temperature (ambient and liquid) shall be 15 °C to 35 °C, unless otherwise specified in the
controlling International Standard.
4.3 Test report
Test results and test conditions shall be reported on the test data form given in annex A.
CAUTION: Some of the tests described in this part of ISO 8434 are considered hazardous. It is therefore
essential that, in conducting these tests, all appropriate safety precautions are strictly adhered to.
Attention is drawn to the danger of burst, fine jets (which can penetrate the skin) and energy release of
expanding gases. To reduce the hazard of energy release, bleed air out of test specimens prior to pressure
file:///C|/$Works/Docs/2/iso-08434-5.htm (4 of 13) [17.03.2003 12:24:48]
5. iso-8434 - Part 5
testing. Tests shall be set up and performed by properly trained personnel.
5 Proof pressure test
5.1 Principle
Testing of three samples to confirm that the specified connection (s) meet (s) or exceed (s) a ratio of 2:1
between the proof and working pressure for 60 s minimum at proof pressure without any visual signs of
leakage.
5.2 Test equipment
5.2.1 Test block
Test blocks shall be unplated and hardened to 45 HRC to 55 HRC in accordance with ISO 6508. The
distance between the centrelines of test ports shall be a minimum of 1,5 times the port diameter. The
distance between the port centreline and the edge of the test block shall be a minimum of 1 times the port
diameter.
5.2.2 Test seals (if applicable)
Unless otherwise specified, seals shall be nitrile (NBR) rubber with a hardness of (90 ± 5) IHRD when
measured in accordance with ISO 48. Seals shall conform to their respective dimensional requirements,
and O-rings shall meet or exceed the quality requirements for grade N (general purpose) of ISO 3601-3,
if applicable.
5.3 Procedure
5.3.1 Thread lubrication
For testing only, threads and contact surfaces shall be lubricated with hydraulic oil with a viscosity of
VG 32 in accordance with ISO 3448 prior to application of torque.
5.3.2 Torque
Tube connections and stud ends shall be tested at the required minimum torques of the respective
connector standard, if specified. Otherwise test at the minimum torque values supplied by the
manufacturer. Adjustable stud torques shall be applied after being backed out one full turn from finger-
file:///C|/$Works/Docs/2/iso-08434-5.htm (5 of 13) [17.03.2003 12:24:48]
6. iso-8434 - Part 5
tight position to test correctly the worst possible actual assembly conditions.
5.3.3 Pressure rise rate
During the proof test, the rate of pressure rise shall not exceed 138 MPa/min (1 380 bar1)/min).
1) 1 bar=0,1 MPa=105 Pa; 1 MPa=1 N/mm2
5.4 Re-use of components
Parts that pass this test may be used for other tests or in production.
6 Failure pressure test (Burst)
6.1 Principle
Testing of three samples to confirm that the specified connection (s) is (are) capable of withstanding a
minimum of four times the working pressure without failure.
6.2 Test equipment
Use the same equipment as in 5.2.
6.3 Procedures
Use the same procedures as in 5.3, except that the rate of pressure rise shall be constant and be chosen to
reach the final pressure within 30 s to 60 s.
6.4 Re-use of components
Parts that pass this test shall not be tested further, used or returned to stock.
7 Cyclic endurance test
file:///C|/$Works/Docs/2/iso-08434-5.htm (6 of 13) [17.03.2003 12:24:48]
7. iso-8434 - Part 5
7.1 Principle
Testing of six samples at their respective impulse pressure to confirm that they pass a cyclic endurance
test for 1 000 000 cycles without leakage or component failure.
7.2 Test equipment
Use the same equipment as in 5.2.
7.3 Procedures
7.3.1 Thread lubrication
Use the lubricant specified in 5.3.1.
7.3.2 Torques
Apply torque as specified in 5.3.2.
7.3.3 Cycle rate
The cycle rate shall be uniform at 0,5 Hz to 1,3 Hz and shall conform to the wave pattern shown in ISO
6803.
7.4 Re-use of components
Parts that pass this test shall not be tested further, used or returned to stock.
8 Vacuum test
8.1 Principle
Testing of two samples to confirm that they are capable of withstanding a vacuum of 6,5 kPa (0,065 bar)
absolute pressure for 5 min without leakage.
8.2 Test equipment
file:///C|/$Works/Docs/2/iso-08434-5.htm (7 of 13) [17.03.2003 12:24:48]
8. iso-8434 - Part 5
Use the same equipment as specified in 5.2.
8.3 Procedure
8.3.1 Thread lubrication
Use the lubricant specified in 5.3.1.
8.3.2 Torque
Apply torque as specified in 5.3.2.
8.4 Re-use of components
Parts that pass this test may be used for other tests or in production.
9 Overtorque test
9.1 Principle
Testing of six samples to confirm that they are capable of withstanding the overtorque qualification test
when tested to the overtorque values shown in their respective standards.
9.2 Test equipment
An unplated threaded steel mandrel hardened to 40 HRC to 45 HRC in accordance with ISO 6508 shall
be used.
9.3 Procedure
9.3.1 Thread lubrication
Use the lubricant specified in 5.3.1.
9.3.2 Wrenching requirements
file:///C|/$Works/Docs/2/iso-08434-5.htm (8 of 13) [17.03.2003 12:24:48]
9. iso-8434 - Part 5
Connections shall be restrained during the test and the wrench shall be located at the threaded end of the
nut hex.
9.4 Re-use of components
Parts that pass this test shall not be tested further, used or returned to stock.
10 Identification statement (Reference to this part
of ISO 8434)
Use the following statement in test reports, catalogues and sales literature when electing to comply with
this part of ISO 8434: "Test methods for metallic tube connections conform to ISO 8434-5:1995,
Metallic tube connections for fluid power and general use — Part 5: Test methods for threaded hydraulic
fluid power connections."
Annex A
Test data form
(normative)
Specifications for connection being tested: ISO standard Material type
Manufacturer Test facility
Stud end type Size
Proof pressure test results: min. number of samples tested = 3 Test pressure,MPa...
Sample No. Hardness Torque Pressure at failure Type of failure
1 ... HRB ... N*m ... MPa ...
2 ... HRB ... N*m ... MPa ...
3 ... HRB ... N*m ... MPa ...
Failure test (Burst) results: min. number of samples tested = 3 Test pressure,MPa...
Sample No. Hardness Torque Pressure at failure Type of failure
1 ... HRB ... N*m ... MPa ...
2 ... HRB ... N*m ... MPa ...
file:///C|/$Works/Docs/2/iso-08434-5.htm (9 of 13) [17.03.2003 12:24:48]
10. iso-8434 - Part 5
3 ... HRB ... N*m ... MPa ...
Cyclic endurance test results: min. number of samples tested = 6 Test pressure, MPa ...
Sample No. Hardness Torque Cycles at failure Type of failure
1 ... HRB ... N*m ... ...
2 ... HRB ... N*m ... ...
3 ... HRB ... N*m ... ...
4 ... HRB ... N*m ... ...
5 ... HRB ... N*m ... ...
6 ... HRB ... N*m ... ...
Vacuum test results: min. number of samples tested = 2 Test pressure, kPa abs. ...
Sample No. Hardness Torque Pressure absolute Type of failure
1 ... HRB ... N*m ... kPa ...
2 ... HRB ... N*m ... kPa ...
Overtorque test results: min. number of samples tested = 6 Test torque, N*m ...
Sample No. Nut hardness Torque at failure Type of failure
1 ... HRB ... N*m ...
2 ... HRB ... N*m ...
3 ... HRB ... N*m ...
4 ... HRB ... N*m ...
5 ... HRB ... N*m ...
6 ... HRB ... N*m ...
Conclusions: Pass/fail with reason for failure.
Dimensions (list any exceptions):
Name (printed/typed) and signature of person certifying report:
Date:
Annex Â
Applicable tests for various fitting and stud end
standards
file:///C|/$Works/Docs/2/iso-08434-5.htm (10 of 13) [17.03.2003 12:24:48]
11. iso-8434 - Part 5
(informative)
Fitting and stud
end standards1)
Tests per ISO 8434-5
Proof pressure
Failure
pressure
(Burst)
Cyclic
endurance
Vacuum Overtorque
Fittings
ISO 8434-1 Yes Yes No No No
ISO 8434-2 Yes Yes No No No
ISO 8434-3 Yes Yes Yes Yes Yes
ISO 8434-4 Yes Yes No No No
Stud ends
ISO 1179-2 No Yes Yes No No
ISO 1179-3 No Yes Yes No No
ISO 1179-4 No Yes Yes No No
ISO 6149-222) No Yes Yes No No
ISO 6149-32) No Yes Yes No No
ISO 9974-2 No Yes Yes No No
ISO 9974-3 No Yes Yes No No
ISO 11926-2 No Yes Yes No No
ISO 11926-3 No Yes Yes No No
1) See annex Ñ.
2) Preferred for new designs in hydraulic fluid power applications.
Annex Ñ
Bibliography
(informative)
[1] ISO 1179-2:—2), Connections for general use and fluid power — Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing — Part 2: Heavy-duty (S series) and light-duty (L
series) stud ends with elastomeric sealing (type E).
file:///C|/$Works/Docs/2/iso-08434-5.htm (11 of 13) [17.03.2003 12:24:48]
12. iso-8434 - Part 5
[2] ISO 1179-3:—2), Connections for general use and fluid power — Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing — Part 3: Light-duty (L series) stud ends with sealing
by O-ring with retaining ring (types G and H).
[3] ISO 1179-4:—2), Connections for general use and fluid power — Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing — Part 4: Stud ends for general use only with metal-
to-metal sealing (type B).
[4] ISO 6149-2:1993, Connections for fluid power and general use — Ports and stud ends with I SO 261
threads and O-ring sealing — Part 2: Heavy-duty (S series) stud ends — Dimensions, design, test
methods and requirements.
[5] ISO 6149-3:1993, Connections for fluid power and general use — Ports and stud ends with ISO 261
threads and O-ring sealing — Part 3: Light-duty (L series) stud ends — Dimensions, design, test methods
and requirements.
[6] I SO 8434-1:1994, Metallic tube connections for fluid power and general use — Part 1: 24 degree
compression fittings.
[7] ISO 8434-2:1994, Metallic tube connections for fluid power and general use — Part 2: 37 degree
flared fittings.
[8] I SO 8434-3:1995, Metallic tube connections for fluid power and general use — Part 3: O-ring face
seal fittings.
[9] I SO 8434-4:1995, Metallic tube connections for fluid power and general use — Part 4: 24 degree
cone connectors with O-ring weld-on nipples.
[10] ISO 9974-2:—2), Connections for general use and fluid power — Ports and stud ends with ISO 261
threads with elastomeric or metal-to-metal sealing — Part 2: Stud ends with elastomeric sealing (type
E).
[11] ISO 9974-3:—2), Connections for general use and fluid power — Ports and stud ends with ISO 261
threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type
B).
[12] ISO 11926-2:1995, Connections for general use and fluid power — Ports and stud ends with ISO
725 threads and O-ring sealing — Part 2: Heavy-duty (S series) stud ends.
[13] ISO 11926-3:1995, Connections for general use and fluid power — Ports and stud ends with ISO
725 threads and O-ring sealing — Part 3: Light duty (L series) stud ends.
file:///C|/$Works/Docs/2/iso-08434-5.htm (12 of 13) [17.03.2003 12:24:48]
13. iso-8434 - Part 5
2) To be published.
ICS 23.100.30
Descriptors: hydraulic fluid power, pneumatic fluid power, fluid circuits, pipes (tubes), metal tubes,
hoses, pipe joints, pipe fittings, compression fittings, screwed connections, stud ends, tests, performance
tests.
Price based on 7 pages
file:///C|/$Works/Docs/2/iso-08434-5.htm (13 of 13) [17.03.2003 12:24:48]