Iron-SGS Report.PDF
•
0 likes•485 views
琼
琼 刘1) SGS tested a silver-grey metal board sample submitted by SONIER PINS CO.,LTD. for levels of cadmium, lead, mercury, and hexavalent chromium. 2) Test results showed the levels of cadmium, lead, mercury, and hexavalent chromium in the sample complied with limits set by the RoHS Directive. 3) Based on the test results, SGS concluded the sample was compliant with restrictions on hazardous substances as defined by the RoHS Directive.
Report
Share
Report
Share
Download to read offline
Recommended
Brass-SGS Report.PDF
1. SGS tested a sample submitted by SONIER PINS CO.,LTD for compliance with the RoHS Directive (EU) 2015/863.
2. Test results found lead content of 40 mg/kg and all other regulated substances were not detected.
3. Based on the test results, the sample was found to comply with limits for lead, mercury, cadmium, and hexavalent chromium as set by the RoHS Directive.
Iron-SGS Report-.PDF
This 3-page test report provides results of tests conducted on a sample submitted by SONIER PINS CO., LTD. between October 24-31, 2016. Chemical composition analysis found the sample to contain 0.035% carbon, 0.24% manganese, 0.013% phosphorus, and 0.007% sulfur. Tensile testing yielded a tensile strength of 306 MPa, yield strength of 172 MPa, and 50.5% elongation after fracture. Hardness testing at the surface resulted in readings of 90.3, 90.4, and 92.0 HV10. The signed report was authored by Ramber Li on behalf of SGS-CSTC Standards Technical Services Co.,
benyi SGS test report英文版
This test report summarizes results of various tests conducted on quartz surfaces manufactured by Benyee Technology Holding Co. The tests evaluated properties such as absorption, density, compressive strength, hardness, stain resistance, chemical resistance, and reaction to heat. Across all tests, the quartz surfaces demonstrated low water absorption, high density and strength, hardness of 5-6 on the Mohs scale, strong stain and chemical resistance, and no visible changes after heat exposure. The report provides detailed individual test results and concludes the quartz surfaces met standards based on the tested properties.
Test Report of Rhinestone from SGS for Heavy metal content
This test report from SGS Testing Korea provides results of lead testing on a sample submitted by Amazing Co., Ltd. The sample consisted of one rhinestone crystal piece (A) and metal stud (B) with glue. Testing found 60.4 mg/kg of lead in part A but lead was not detected in part B above the 5 mg/kg detection limit. The report provides details of the testing methodology and concludes with a picture of the sample as received.
Brass-SGS Report-.PDF
This 3-page test report provides results of chemical composition analysis, tensile tests, and hardness tests performed on a copper sample submitted by SONIER PINS CO., LTD. Key findings include:
- Chemical composition analysis found the sample to be 61.3% copper, 0.018% iron, <0.01% lead, and 38.69% zinc.
- Tensile tests of rectangular specimens found the tensile strength to be 334 MPa, yield strength to be 117 MPa, and elongation after fracture to be 54.0%.
- Hardness tests at the surface found results of 71.3, 72.3, and 71.5 HV10.
REACH Report.PDF
The document is a 38-page test report from Bay Area Compliance Laboratories Corp. that analyzes samples of LED high bay lights for OK LED Lighting Limited. The report tests the samples for 163 substances of very high concern and finds concentrations of all substances to be <0.1%. The samples tested include various plastic, metal, and PCB parts of the LED lights.
Welding Procces
This document defines welding codes, standards, and welding procedures. It discusses that a standard is a collection of documents containing codes, specifications, recommended practices, classifications, and guidelines that have been prepared by an institution or organization and approved according to existing procedures. A code is a standard that contains conditions and requirements related to a particular subject and indicates that the procedures used comply with the requirements. A specification is a standard that contains detailed and accurate technical requirements for materials, products, systems or services. It provides examples of welding codes from various organizations and discusses the essential variables and requirements for qualifying welding procedures according to ASME and EN standards.
Simdis (simulated distillation)
This document describes a study comparing two methods for determining distillation yield curves in heavy crude oils: ASTM D-5307 simulated distillation using gas chromatography (SIMDIS GC) and ASTM D-2892 physical distillation. The researchers found large uncertainties using ASTM D-5307 and made some improvements. They analyzed Mexican Istmo and Maya crude oil samples using both methods, finding good agreement between the results. The statistical analysis supported SIMDIS GC as a good alternative for measuring distillation curves in heavy crude oils.
Recommended
Brass-SGS Report.PDF
1. SGS tested a sample submitted by SONIER PINS CO.,LTD for compliance with the RoHS Directive (EU) 2015/863.
2. Test results found lead content of 40 mg/kg and all other regulated substances were not detected.
3. Based on the test results, the sample was found to comply with limits for lead, mercury, cadmium, and hexavalent chromium as set by the RoHS Directive.
Iron-SGS Report-.PDF
This 3-page test report provides results of tests conducted on a sample submitted by SONIER PINS CO., LTD. between October 24-31, 2016. Chemical composition analysis found the sample to contain 0.035% carbon, 0.24% manganese, 0.013% phosphorus, and 0.007% sulfur. Tensile testing yielded a tensile strength of 306 MPa, yield strength of 172 MPa, and 50.5% elongation after fracture. Hardness testing at the surface resulted in readings of 90.3, 90.4, and 92.0 HV10. The signed report was authored by Ramber Li on behalf of SGS-CSTC Standards Technical Services Co.,
benyi SGS test report英文版
This test report summarizes results of various tests conducted on quartz surfaces manufactured by Benyee Technology Holding Co. The tests evaluated properties such as absorption, density, compressive strength, hardness, stain resistance, chemical resistance, and reaction to heat. Across all tests, the quartz surfaces demonstrated low water absorption, high density and strength, hardness of 5-6 on the Mohs scale, strong stain and chemical resistance, and no visible changes after heat exposure. The report provides detailed individual test results and concludes the quartz surfaces met standards based on the tested properties.
Test Report of Rhinestone from SGS for Heavy metal content
This test report from SGS Testing Korea provides results of lead testing on a sample submitted by Amazing Co., Ltd. The sample consisted of one rhinestone crystal piece (A) and metal stud (B) with glue. Testing found 60.4 mg/kg of lead in part A but lead was not detected in part B above the 5 mg/kg detection limit. The report provides details of the testing methodology and concludes with a picture of the sample as received.
Brass-SGS Report-.PDF
This 3-page test report provides results of chemical composition analysis, tensile tests, and hardness tests performed on a copper sample submitted by SONIER PINS CO., LTD. Key findings include:
- Chemical composition analysis found the sample to be 61.3% copper, 0.018% iron, <0.01% lead, and 38.69% zinc.
- Tensile tests of rectangular specimens found the tensile strength to be 334 MPa, yield strength to be 117 MPa, and elongation after fracture to be 54.0%.
- Hardness tests at the surface found results of 71.3, 72.3, and 71.5 HV10.
REACH Report.PDF
The document is a 38-page test report from Bay Area Compliance Laboratories Corp. that analyzes samples of LED high bay lights for OK LED Lighting Limited. The report tests the samples for 163 substances of very high concern and finds concentrations of all substances to be <0.1%. The samples tested include various plastic, metal, and PCB parts of the LED lights.
Welding Procces
This document defines welding codes, standards, and welding procedures. It discusses that a standard is a collection of documents containing codes, specifications, recommended practices, classifications, and guidelines that have been prepared by an institution or organization and approved according to existing procedures. A code is a standard that contains conditions and requirements related to a particular subject and indicates that the procedures used comply with the requirements. A specification is a standard that contains detailed and accurate technical requirements for materials, products, systems or services. It provides examples of welding codes from various organizations and discusses the essential variables and requirements for qualifying welding procedures according to ASME and EN standards.
Simdis (simulated distillation)
This document describes a study comparing two methods for determining distillation yield curves in heavy crude oils: ASTM D-5307 simulated distillation using gas chromatography (SIMDIS GC) and ASTM D-2892 physical distillation. The researchers found large uncertainties using ASTM D-5307 and made some improvements. They analyzed Mexican Istmo and Maya crude oil samples using both methods, finding good agreement between the results. The statistical analysis supported SIMDIS GC as a good alternative for measuring distillation curves in heavy crude oils.
HIGH TEMPERATURE AND HIGH PRESSURE CORROSION TESTING AUTOCLAVES
Simulating industrial processes in the laboratory requires facilities to safely handle high temperatures and high pressures, highly corrosive chemicals and toxic materials, as well as the ability to mechanically load test samples during exposure.
The high temperature and high pressure (HTHP) laboratory of TECNALIA has autoclaves, mainly focused on sour and non-sour applications. Corrosion and cracking phenomena which may result from exposure of steels and alloys to H2S, CO2 and brines, are carefully assessed.
For more information https://www.tecnalia.com/en
Saes w-011-welding on plot ( process ) piping
This document outlines welding requirements for on-plot piping at Saudi Aramco. It specifies approved welding processes, welding consumables, welding procedures, welder qualification requirements, joint details, corrosion resistant materials, technique and workmanship standards, preheat and post weld heat treatment needs, production weld hardness testing, inspection access, weld identification, inspection requirements, and repair standards. The document provides detailed requirements to ensure welding is completed according to applicable codes and standards for safety and quality.
Spc sgs spc test report
This test report summarizes results for a wood flooring sample from Jinan Caiming Wood Co. Ltd. in China. It was tested for various physical properties including dimensions, thickness, density, dimensional stability when heated, wear resistance, peel strength, and micro-scratch resistance. The sample was found to meet specifications for size and was rated AC4 for wear resistance, with an average of 4400 abrasion cycles before wear. Micro-scratch resistance was rated MSR-A2 and MSR-B2 under two test procedures.
Asme bpv sec v art. 6
This document outlines procedures and requirements for liquid penetrant examination. It discusses the scope of liquid penetrant examination, referencing documents, general procedures, equipment, requirements, examination process, evaluation, documentation, and definitions. Key steps include surface preparation, application of penetrant, removal of excess penetrant, application of developer, interpretation of results, and documentation. Contaminant control and certification are required for materials used to examine nickel alloys, austenitic stainless steels, and titanium.
ICH Q3AR2 explained - impurities in drug substances
This presentation explains ICH guideline - Q3AR2 in an understandable way by giving examples.
How to impart in the dossier, format for writing impurities in drug substance is given in the book:
1. https://www.scribd.com/book/429190300/Impurities-In-Drug-Substances-ICH-Explained
2. https://www.smashwords.com/books/view/961598
a small book explaining ICH guidelines - impurities in new drug substances with examples
also available in
https://books2search.com/impurities-in-drug-substances-ich-explained-9780463960592
https://www.chapters.indigo.ca/en-ca/books/contributor/author/kiran-nivedh/
Saes w-016-welding special corrosion materials
This document provides welding requirements for special corrosion-resistant materials used in severe corrosion and high temperature applications. It specifies that welding procedures must be qualified according to ASME standards and additional Saudi Aramco requirements. For high temperature applications, ferrite content must be measured and controlled between 3-10 FN. For corrosive services, gas tungsten arc welding is required for certain applications and filler metal selection, joint design, inspection, and other criteria are specified. Additional requirements are outlined for welding duplex stainless steels, including controlling ferrite content, corrosion testing, impact testing, hardness testing, and other variables.
Potential elemental impurities ,chns analyser
This document discusses elemental impurities in pharmaceutical products. It defines elemental impurities as traces of metals that can be introduced during manufacturing from sources like catalysts, equipment, or packaging materials. It identifies several potential sources of elemental impurities and analytical procedures that can be used to detect specific impurities. These include testing for impurities introduced during synthesis, from equipment, excipients, or container leaching. The document also describes CHNS elemental analyzers which can rapidly determine carbon, hydrogen, nitrogen and sulfur content and are widely used in applications like pharmaceuticals, chemicals and food analysis.
Bs 1881 112 1983
This document describes three methods for accelerated curing of concrete test cubes at 35°C, 55°C, and 82°C. The 35°C method involves curing test cubes submerged in a water tank maintained at 35°C ± 2°C for 24 hours. The 55°C method cures cubes at 55°C ± 2°C for at least 19.5 hours then cools them for 1-2 hours at 20°C ± 5°C. The 82°C method raises water in a curing tank to 82°C ± 2°C within 2 hours, holds it for 14 hours, then discharges the water after testing the hot cubes within 1 hour. All methods allow determining concrete
Smart Pigging
PT Sentra Inti Nusa Energi (Sinergi) is an exclusive agent for Rosen Inspection in Indonesia. They provide integrated corrosion engineering services including inline inspection using smart pigs, corrosion prevention, corrosion assessment, and risk analysis. Their services include geometry surveys, corrosion detection, and data analysis using Rosen's intelligent pigging technology to inspect pipelines for defects. They have experience inspecting various oil and gas pipelines between 3-30 inches in diameter and up to 335km in length.
Pharmaceutical Assay and Multicomponent Analysis
Combination drugs containing Paracetamol and Aspirin, displayed in Figure 1, are widely used analgesics with anti-inflammatory properties for treatment of migraines. Both active ingredients have a similar mode of action, whereby they inhibit the cyclooxygenase (COX) enzyme, by preventing the production of prostaglandins which cause pain, inflammation, and fever. UV/Vis spectrometry is a fast and commonly used technique in quality control laboratories for routine analysis of purity and quantity of components within various stages of a product’s manufacture in many industries.
汽车杯的LFGB测试报告
The document is a test report from SGS-CSTC Standards Technical Services Co., Ltd. Ningbo Branch that details test results for plastic mugs and silicone rubber rings produced by Yongkang Runhu Metal Product Factory in China. Various tests were conducted including overall migration, extractable components, sensory examination, color release, specific migration of PAHs and heavy metals, and volatile organic matter. The test results showed that the samples passed all tests conducted.
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general me...
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general metal loss by using fea techniques by kingston.r
2047.pdf
The document is a mill test certificate issued by United Sulb Company (Saudi Sulb) L.L.C. for steel bars delivered to Prime Steel Co. between December 6-8, 2022. It lists the chemical composition, mechanical properties, and test results for various steel profiles that meet EN 10025-2:2019 S275JR specifications. United Sulb certifies that the materials were produced under their ISO 9001:2015 quality management system and conform to the customer's sales contract and purchase order requirements.
Method Development and Validation of Related Substances by HPLC for Analysis ...
Method Development and Validation of Related Substances by HPLC for Analysis of Valacyclovir Hcl in valacyclovir Hcl Tablet Formulations
TWI Training Exam Results
This document is an exam results page from TWI Training showing the results for candidate Ali Ben Youssef who took the CSWIP 3.1 Welding Inspector exam on October 21, 2016 in Abington. The results show that Ali passed all sections of the exam including Pipe Paper, Technology Paper, Plate Paper, General Paper, and Macro Paper. His composite mark met the requirements and his results were forwarded for certification review.
Paut full notes
This document provides an overview of a course on phased array ultrasonic examination for welds. The course objectives include covering the theoretical background of phased array ultrasonics, preparing scan plans and work instructions, setting up equipment and files, optimizing display parameters, scanning welds to detect discontinuities, analyzing scan data, and interpreting and reporting test results. It also covers auditing phased array data and setup files. The document includes brief introductions to automated ultrasonic testing techniques and the history of their development.
Analytical Procedures in Elemental Impurities
This document discusses analytical procedures for determining elemental impurities like arsenic, lead, and mercury. It provides details on the methodology and reagents used for arsenic detection using the molybdenum blue method and atomic absorption spectrometry. For lead, the dithizone method is described where lead ions form a brown colloid with dithizone. Mercury detection uses the mercury(II) thiocyanate method where chloride ions displace thiocyanate and form a colored complex with iron(III). Spectrophotometric techniques are used for quantification and calibration curves.
Sistematicas calculo precision en microbiologia (2)
Este documento compara cuatro métodos para estimar la precisión de los métodos cuantitativos en microbiología. Los métodos incluyen: ISO/TS 19036, que solo considera la precisión; ISO 16140, que usa estimadores robustos basados en la mediana; ANZ AS TG 5, que calcula la desviación estándar de réplicas; y un método propuesto en IBEROLAB 2005. El documento concluye que los cuatro métodos no muestran diferencias significativas en sus resultados, aunque difieren en su planteamiento inicial.
Ut P3
This document discusses ultrasonic testing techniques. It describes different methods for sound generation including hammers, magnetostrictive, and piezoelectric techniques. It then focuses on piezoelectric probes, explaining how they work using polarized crystal materials like lead zirconate titanate. Different probe designs are described for compression and shear waves. Factors that determine probe frequency like crystal thickness are also covered. Finally, automated inspection techniques are briefly outlined.
pipe shedule chart
This document provides specifications for pipe dimensions including nominal pipe size, outside diameter, schedule/wall thickness, and weight. It lists pipe sizes from 1/8 inch to 2-1/2 inches in nominal increments along with the corresponding dimensions and weights in both US customary and metric units. A wide variety of schedule designations are specified for each size providing variation in wall thickness and therefore weight.
Deep Dive into OpenStack
OpenStack is a leading open-source project to build public/private clouds. In this talk, a brief introduction of Openstack will be presented, following by a detail technical description of internal structure of main openstack software, including openstack compute, storage, and glance. This talk will also introduce a Dell's crowbar solution to automatically deploy and configure openstack software to build a large scale cloud infrastructure. Finally, Information about some of on-going development effort in the community will be shared with audience.
Algorithmic Trading Basics: Strategies & Systems
Learn more about our algorithmic trading system in this free white paper. Inside we detail the methodology behind our algorithms and our trading system. This automated trading system white paper covers the basics of algorithmic trading, strategies and systems.
More Related Content
What's hot
HIGH TEMPERATURE AND HIGH PRESSURE CORROSION TESTING AUTOCLAVES
Simulating industrial processes in the laboratory requires facilities to safely handle high temperatures and high pressures, highly corrosive chemicals and toxic materials, as well as the ability to mechanically load test samples during exposure.
The high temperature and high pressure (HTHP) laboratory of TECNALIA has autoclaves, mainly focused on sour and non-sour applications. Corrosion and cracking phenomena which may result from exposure of steels and alloys to H2S, CO2 and brines, are carefully assessed.
For more information https://www.tecnalia.com/en
Saes w-011-welding on plot ( process ) piping
This document outlines welding requirements for on-plot piping at Saudi Aramco. It specifies approved welding processes, welding consumables, welding procedures, welder qualification requirements, joint details, corrosion resistant materials, technique and workmanship standards, preheat and post weld heat treatment needs, production weld hardness testing, inspection access, weld identification, inspection requirements, and repair standards. The document provides detailed requirements to ensure welding is completed according to applicable codes and standards for safety and quality.
Spc sgs spc test report
This test report summarizes results for a wood flooring sample from Jinan Caiming Wood Co. Ltd. in China. It was tested for various physical properties including dimensions, thickness, density, dimensional stability when heated, wear resistance, peel strength, and micro-scratch resistance. The sample was found to meet specifications for size and was rated AC4 for wear resistance, with an average of 4400 abrasion cycles before wear. Micro-scratch resistance was rated MSR-A2 and MSR-B2 under two test procedures.
Asme bpv sec v art. 6
This document outlines procedures and requirements for liquid penetrant examination. It discusses the scope of liquid penetrant examination, referencing documents, general procedures, equipment, requirements, examination process, evaluation, documentation, and definitions. Key steps include surface preparation, application of penetrant, removal of excess penetrant, application of developer, interpretation of results, and documentation. Contaminant control and certification are required for materials used to examine nickel alloys, austenitic stainless steels, and titanium.
ICH Q3AR2 explained - impurities in drug substances
This presentation explains ICH guideline - Q3AR2 in an understandable way by giving examples.
How to impart in the dossier, format for writing impurities in drug substance is given in the book:
1. https://www.scribd.com/book/429190300/Impurities-In-Drug-Substances-ICH-Explained
2. https://www.smashwords.com/books/view/961598
a small book explaining ICH guidelines - impurities in new drug substances with examples
also available in
https://books2search.com/impurities-in-drug-substances-ich-explained-9780463960592
https://www.chapters.indigo.ca/en-ca/books/contributor/author/kiran-nivedh/
Saes w-016-welding special corrosion materials
This document provides welding requirements for special corrosion-resistant materials used in severe corrosion and high temperature applications. It specifies that welding procedures must be qualified according to ASME standards and additional Saudi Aramco requirements. For high temperature applications, ferrite content must be measured and controlled between 3-10 FN. For corrosive services, gas tungsten arc welding is required for certain applications and filler metal selection, joint design, inspection, and other criteria are specified. Additional requirements are outlined for welding duplex stainless steels, including controlling ferrite content, corrosion testing, impact testing, hardness testing, and other variables.
Potential elemental impurities ,chns analyser
This document discusses elemental impurities in pharmaceutical products. It defines elemental impurities as traces of metals that can be introduced during manufacturing from sources like catalysts, equipment, or packaging materials. It identifies several potential sources of elemental impurities and analytical procedures that can be used to detect specific impurities. These include testing for impurities introduced during synthesis, from equipment, excipients, or container leaching. The document also describes CHNS elemental analyzers which can rapidly determine carbon, hydrogen, nitrogen and sulfur content and are widely used in applications like pharmaceuticals, chemicals and food analysis.
Bs 1881 112 1983
This document describes three methods for accelerated curing of concrete test cubes at 35°C, 55°C, and 82°C. The 35°C method involves curing test cubes submerged in a water tank maintained at 35°C ± 2°C for 24 hours. The 55°C method cures cubes at 55°C ± 2°C for at least 19.5 hours then cools them for 1-2 hours at 20°C ± 5°C. The 82°C method raises water in a curing tank to 82°C ± 2°C within 2 hours, holds it for 14 hours, then discharges the water after testing the hot cubes within 1 hour. All methods allow determining concrete
Smart Pigging
PT Sentra Inti Nusa Energi (Sinergi) is an exclusive agent for Rosen Inspection in Indonesia. They provide integrated corrosion engineering services including inline inspection using smart pigs, corrosion prevention, corrosion assessment, and risk analysis. Their services include geometry surveys, corrosion detection, and data analysis using Rosen's intelligent pigging technology to inspect pipelines for defects. They have experience inspecting various oil and gas pipelines between 3-30 inches in diameter and up to 335km in length.
Pharmaceutical Assay and Multicomponent Analysis
Combination drugs containing Paracetamol and Aspirin, displayed in Figure 1, are widely used analgesics with anti-inflammatory properties for treatment of migraines. Both active ingredients have a similar mode of action, whereby they inhibit the cyclooxygenase (COX) enzyme, by preventing the production of prostaglandins which cause pain, inflammation, and fever. UV/Vis spectrometry is a fast and commonly used technique in quality control laboratories for routine analysis of purity and quantity of components within various stages of a product’s manufacture in many industries.
汽车杯的LFGB测试报告
The document is a test report from SGS-CSTC Standards Technical Services Co., Ltd. Ningbo Branch that details test results for plastic mugs and silicone rubber rings produced by Yongkang Runhu Metal Product Factory in China. Various tests were conducted including overall migration, extractable components, sensory examination, color release, specific migration of PAHs and heavy metals, and volatile organic matter. The test results showed that the samples passed all tests conducted.
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general me...
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general metal loss by using fea techniques by kingston.r
2047.pdf
The document is a mill test certificate issued by United Sulb Company (Saudi Sulb) L.L.C. for steel bars delivered to Prime Steel Co. between December 6-8, 2022. It lists the chemical composition, mechanical properties, and test results for various steel profiles that meet EN 10025-2:2019 S275JR specifications. United Sulb certifies that the materials were produced under their ISO 9001:2015 quality management system and conform to the customer's sales contract and purchase order requirements.
Method Development and Validation of Related Substances by HPLC for Analysis ...
Method Development and Validation of Related Substances by HPLC for Analysis of Valacyclovir Hcl in valacyclovir Hcl Tablet Formulations
TWI Training Exam Results
This document is an exam results page from TWI Training showing the results for candidate Ali Ben Youssef who took the CSWIP 3.1 Welding Inspector exam on October 21, 2016 in Abington. The results show that Ali passed all sections of the exam including Pipe Paper, Technology Paper, Plate Paper, General Paper, and Macro Paper. His composite mark met the requirements and his results were forwarded for certification review.
Paut full notes
This document provides an overview of a course on phased array ultrasonic examination for welds. The course objectives include covering the theoretical background of phased array ultrasonics, preparing scan plans and work instructions, setting up equipment and files, optimizing display parameters, scanning welds to detect discontinuities, analyzing scan data, and interpreting and reporting test results. It also covers auditing phased array data and setup files. The document includes brief introductions to automated ultrasonic testing techniques and the history of their development.
Analytical Procedures in Elemental Impurities
This document discusses analytical procedures for determining elemental impurities like arsenic, lead, and mercury. It provides details on the methodology and reagents used for arsenic detection using the molybdenum blue method and atomic absorption spectrometry. For lead, the dithizone method is described where lead ions form a brown colloid with dithizone. Mercury detection uses the mercury(II) thiocyanate method where chloride ions displace thiocyanate and form a colored complex with iron(III). Spectrophotometric techniques are used for quantification and calibration curves.
Sistematicas calculo precision en microbiologia (2)
Este documento compara cuatro métodos para estimar la precisión de los métodos cuantitativos en microbiología. Los métodos incluyen: ISO/TS 19036, que solo considera la precisión; ISO 16140, que usa estimadores robustos basados en la mediana; ANZ AS TG 5, que calcula la desviación estándar de réplicas; y un método propuesto en IBEROLAB 2005. El documento concluye que los cuatro métodos no muestran diferencias significativas en sus resultados, aunque difieren en su planteamiento inicial.
Ut P3
This document discusses ultrasonic testing techniques. It describes different methods for sound generation including hammers, magnetostrictive, and piezoelectric techniques. It then focuses on piezoelectric probes, explaining how they work using polarized crystal materials like lead zirconate titanate. Different probe designs are described for compression and shear waves. Factors that determine probe frequency like crystal thickness are also covered. Finally, automated inspection techniques are briefly outlined.
pipe shedule chart
This document provides specifications for pipe dimensions including nominal pipe size, outside diameter, schedule/wall thickness, and weight. It lists pipe sizes from 1/8 inch to 2-1/2 inches in nominal increments along with the corresponding dimensions and weights in both US customary and metric units. A wide variety of schedule designations are specified for each size providing variation in wall thickness and therefore weight.
What's hot (20)
HIGH TEMPERATURE AND HIGH PRESSURE CORROSION TESTING AUTOCLAVES
HIGH TEMPERATURE AND HIGH PRESSURE CORROSION TESTING AUTOCLAVES
ICH Q3AR2 explained - impurities in drug substances
ICH Q3AR2 explained - impurities in drug substances
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general me...
Level 3 assessment as per api 579 1 asme ffs-1 for pressure vessel general me...
Method Development and Validation of Related Substances by HPLC for Analysis ...
Method Development and Validation of Related Substances by HPLC for Analysis ...
Sistematicas calculo precision en microbiologia (2)
Sistematicas calculo precision en microbiologia (2)
Viewers also liked
Deep Dive into OpenStack
OpenStack is a leading open-source project to build public/private clouds. In this talk, a brief introduction of Openstack will be presented, following by a detail technical description of internal structure of main openstack software, including openstack compute, storage, and glance. This talk will also introduce a Dell's crowbar solution to automatically deploy and configure openstack software to build a large scale cloud infrastructure. Finally, Information about some of on-going development effort in the community will be shared with audience.
Algorithmic Trading Basics: Strategies & Systems
Learn more about our algorithmic trading system in this free white paper. Inside we detail the methodology behind our algorithms and our trading system. This automated trading system white paper covers the basics of algorithmic trading, strategies and systems.
The Ancient Spanish Monastery & Gardens Education Activity Workbook 1-15-17
The Ancient Spanish Monastery & Gardens Education Activity Workbook 1-15-17Daniel H. Markarian Ed.D.
The document is an education activity workbook for students based on Florida education standards. It contains 3 activities related to the Ancient Spanish Monastery and Gardens. Activity 1 involves drawing and describing modifications to the monastery. Activity 2 has students identify and explain primary and secondary sources. Activity 3 asks students to list and describe natural and man-made landmarks of the monastery.Albert einstein
Einstein creía que el ser humano puede desarrollar su intelecto tanto como lo desee. Se destacó por su Teoría de la Relatividad Especial de 1905 y por demostrar que la masa y la energía son equivalentes. Fue galardonado con el Premio Nobel de Física en 1921 por sus contribuciones a la física teórica y especialmente por su descubrimiento de la ley del efecto fotoeléctrico. A lo largo de su vida, Einstein reflexionó sobre temas como la educación, la ciencia, la religión, la paz mundial
Zinc alloy-SGS Report-.PDF
This 3-page test report summarizes the results of tests conducted on a zinc alloy sample submitted by Sonier Pins Co., Ltd. located in Zhongshan City, China. Chemical composition analysis found the sample to contain 3.84% aluminum and small amounts of other elements. Tensile testing of round specimens found the tensile strength to be 294 MPa and yield strength to be 201 MPa, with an elongation after fracture of 3.5%. Hardness testing at the surface found values of 113, 116, and 114 HV10. Photographs of the original sample are also included.
1.aprendiendo a buscar en gogle. (1)
El documento habla sobre las ventajas y desventajas del internet, así como cuidados y precauciones al usarlo. Entre las ventajas menciona la inmediatez de la información, la masificación de contenido y la eliminación de barreras de tiempo y espacio. Entre las desventajas nombra el robo de cuentas bancarias, la falta de veracidad de la información, y la dependencia del uso excesivo. Recomienda no subir información personal ni fotos comprometedoras, ser cuidadoso con quién se chatea, y ev
Zinc alloy-SGS Report.PDF
This test report summarizes the results of tests conducted on a zinc alloy sample submitted by SONIER PINS CO.,LTD between October 25-28, 2016. Testing found that levels of lead, mercury, cadmium, and hexavalent chromium in the sample complied with limits set by the RoHS Directive. Specifically, the tests detected 16 mg/kg of lead and found mercury, cadmium, and hexavalent chromium to be not detected, below their respective limits of 1,000 mg/kg, 100 mg/kg, and 0.10 μg/cm2. The tests were conducted in accordance with referenced standards and the sample was found to meet requirements for a RoHS-compliant zinc
Manoj__Kumar_Yadav Resume
Manoj Kumar Yadav is seeking a position as a Chemist that utilizes his over 8 years of experience in chemical process control and water treatment. He holds a B.Sc. in Chemistry, Botany, and Zoology and is proficient in MS Office, SAP, and other applications. His experience includes analytical testing, plant operations and maintenance, instrumentation calibration, and report preparation at multiple thermal power plants. He is looking for a challenging role with a salary of Rs. 6 lacs per year including accommodation and phone allowance.
11 web 2.0 εργαλεία για την τάξη
Εργασία μαθητών που υλοποιήθηκε στα πλαίσια του μαθήματος της ερευνητικής εργασίας που πραγματοποιήθηκε κατά τη διάρκεια του Β’ τετραμήνου του σχολικού έτους 2011-2012. Οι μαθητές ανέλαβαν να γράψουν ένα μικρό manual για μία web 2.0 εφαρμογή.
Instagram(インスタグラム)集客＆LINE@リピート対策セミナー(長野県)大町商工会議所主催チラシ
Instagram(インスタグラム)集客＆LINE@リピート対策セミナー(長野県)大町商工会議所主催チラシ
Viewers also liked (14)
The Ancient Spanish Monastery & Gardens Education Activity Workbook 1-15-17
The Ancient Spanish Monastery & Gardens Education Activity Workbook 1-15-17
Instagram(インスタグラム)集客＆LINE@リピート対策セミナー(長野県)大町商工会議所主催チラシ
Instagram(インスタグラム)集客＆LINE@リピート対策セミナー(長野県)大町商工会議所主催チラシ
Similar to Iron-SGS Report.PDF
RoHs report of am labels from jizosecurity
This document is a test report from SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. analyzing samples submitted by SHANGHAI JIZO TRADING CO.,LTD. for lead, mercury, cadmium, and hexavalent chromium content. Testing was performed from June 27 to June 30, 2017 according to specified standards. The results indicated that the sample identified as AM Label, a silvery metal, complied with limits for lead, mercury, cadmium, and hexavalent chromium as defined by the RoHS Directive. The report provides test methods used and details of sample preparation and testing procedures.
AEBO SGS.PDF
The test report provides results for substances restricted under the RoHS Directive 2011/65/EU in a sample submitted by a client. Testing was conducted from June 8-10, 2015 on a black soft sheet material. Test results showed lead content of 6 mg/kg and all other regulated substances including cadmium, mercury, hexavalent chromium, PBBs, and PBDEs were not detected. The report concludes the sample complies with limits set by the RoHS Directive.
AEBO SGS.PDF
The test report provides results for substances restricted under the RoHS Directive 2011/65/EU in a sample submitted by a client. Testing was conducted from June 8-10, 2015 on a black soft sheet material. Test results showed lead content of 6 mg/kg and all other regulated substances including cadmium, mercury, hexavalent chromium, PBBs, and PBDEs were not detected. The report concludes the sample complies with limits set by the RoHS Directive.
RoHS test report by SGS on 2012
1) A test report from SGS-CSTC Ltd. details testing of recycled PU foam samples submitted by Shanghai Baiji Sponge Products Co., Ltd.
2) Testing was conducted from September 18-21, 2012 for compliance with the RoHS Directive 2011/65/EU.
3) Test results showed cadmium, lead, mercury, hexavalent chromium, and sums of PBBs/PBDEs were all below their respective limits.
Tuv ROHS certificate --plastic pneumatic push in fittings
XHnotion pneumatic fittings get ROHS certificate from TUV.
This is new series fittings. Material is made from Nylon.
Lighter weight and corrision resistance.
RoHs report of RF labels from jizosecurity
This 5-page test report details the results of tests conducted on a sample submitted by Shanghai Jizo Trading Co., Ltd and identified as an RF label. Testing was conducted from June 27 to 30, 2017 and included analyses for substances restricted under the RoHS Directive. The label sample was found to comply with all limits tested for cadmium, lead, mercury, hexavalent chromium, and sums of PBBs and PBDEs, with all results reported as "ND" (not detected). Testing methods and analytical equipment used are described across multiple pages of detailed results, notes, and attachments.
Rohs test report
1) Two samples of silvery metal with black coating were submitted to SGS for testing.
2) The samples were tested for levels of cadmium, lead, mercury, and hexavalent chromium according to standard methods.
3) Test results showed that levels of all regulated substances were below their respective limits as defined in the RoHS Directive 2011/65/EU.
SGS
The document is a test report from SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. analyzing samples of polyolefin shrink film. It finds that the levels of cadmium, lead, mercury, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers in the samples do not exceed limits set by the RoHS Directive (EU) 2015/863. The report provides details on the test methods, samples, parameters, and results.
RoHS certification of Honcell Energy
The test report summarizes the results of testing various components of a lithium-ion polymer battery submitted by Shenzhen Honcell Energy Co., Ltd. for restricted substances. Several samples were found to contain levels of lead, cadmium, chromium, and chromium VI above the specified limits. The report provides test results and measurements for each sample part analyzed.
RoHs report
This consolidated test report summarizes RoHS testing of components in an electric self-balanced unicycle. Testing was conducted by Shenzhen BCTC Technology Co. and other labs on plastics, wires, screws, capacitors, resistors and other components. Test results found lead levels below limits in most components, with some exceptions. The report concludes that test data did not exceed limits of the RoHS Directive.
Informe de prueba sgs fibra de bambú
- The test report summarizes the results of various analyses conducted on a bamboo fiber tableware sample submitted by a client.
- Tests were conducted for overall migration, sensorial examination of odor and taste, specific migration of formaldehyde, primary aromatic amines, heavy metals, pentachlorophenol, and total bisphenol A content.
- The results indicated that the sample passed all tests and was compliant with relevant EU regulations for food contact materials.
塑料咖啡杯的TUV测试报告
This 3-page test report summarizes the results of tests conducted on a plastic mug (Model RH121-12) submitted by Yongkang Runhu Metal Product Factory. A series of tests were conducted to test for odor, taste, overall migration, specific migration of chemicals like heavy metals, BPA and phthalates, and total lead and cadmium content. All test results indicated the plastic mug passed relevant food contact material standards and regulations. The technical director of TUV Thuringen Shanghai Co. Ltd. signed off on the report.
REACH certification of Honcell Energy
The document is a test report summarizing the results of testing a lithium ion polymer battery for substances of very high concern (SVHC). Testing was conducted for 161 SVHC substances using various analytical methods. The summary states that concentrations of all 161 SVHC substances tested were found to be less than 0.1% in the submitted sample.
EN60454-3-1.PDF
The document is a test report from SGS-CSTC Standards Technical Services (Tianjin) Co., Ltd. evaluating the properties of a PVC tape sample submitted by ZHENGZHOU YOU TRUST TECH CO.,LTD. The report details the results of 11 tests performed on the sample including dielectric strength, adhesion, tensile strength, thickness, and flammability. All test results met the specified requirements and the tape was deemed to have passed testing for its intended use.
Jop description for Senior lab chemist ( shift leader)
The document summarizes the duties and responsibilities of a senior lab chemist at an ethylene, utility, and environmental laboratory. Key responsibilities included supervising a shift team, ensuring correct and timely reporting of test results to customers, maintaining quality standards and accreditation, conducting safety audits, and being an expert in a wide range of analytical testing methods for samples like condensates, naphthas, gases, and amine solutions. Maintaining ISO/IEC 17025 accreditation and safety standards were priorities.
X-ACT 625i- AMBIENT CONTINUOUS METALS MONITOR
Cooper Environmental’s Xact® 625i is designed for high time resolution multi-metals monitoring of ambient air, with detection limits that rival those of laboratory analysis. The Xact® 625i comes standard with a solid-state meteorological sensor and Cooper Environmental’s proprietary ADAPT analysis package, making the instrument one of the most powerful air pollution source detection offerings in the industry. ask info here: https://etserv.be/product/cooper-environmental-xact-625i/
Identification and Confirmation of Ten Common Seized Drugs Utilizing a Single...
Identification and Confirmation of Ten Common Seized Drugs Utilizing a Single...Shimadzu Scientific Instruments
This document describes the development of a method to analyze 10 common seized drugs using a single quadrupole mass spectrometer. A LC-MS method was optimized to separate and detect the drugs simultaneously using selected ion monitoring and in-source collision-induced dissociation for identification. Linear calibration curves were obtained for each drug from 0.1-1 μg/mL. The method demonstrated reproducibility and accuracy for rapid screening of multiple drugs.Presentation on glc_vanshika_varshney
Gas chromatography is a common type of chromatography used in analytical chemistry for separating and analyzing compounds that can be vaporized without decomposition. Typical uses of GC include testing the purity of a particular substance or separating the different components of a mixture.
Aiyinda 703 EN
1) A test report from SGS outlines results from testing a sample submitted by AGFA IMAGING (SHENZHEN) CO.,LTD. referred to as AIYINDA 703.
2) Testing was conducted between December 24th to 28th 2013 and included analyzing for substances restricted by the RoHS Directive and certain phthalates.
3) Results showed the sample contained 4 ppm of lead and was compliant with limits for cadmium, mercury, hexavalent chromium, PBBs, PBDEs, and phthalates like DEHP and BBP.
Sulfur Analysis by GC-SCD using Shimadzu’s SCD-2030 for ASTM D5504, D5623, an...
Sulfur Analysis by GC-SCD using Shimadzu’s SCD-2030 for ASTM D5504, D5623, an...Shimadzu Scientific Instruments
Analysis for and quantification of sulfur in crude oil, natural gas, petrochemicals, and industrial chemicals is critical to ensuring quality, process control, and safety for refinery, processors, and users. Understanding the speciation and concentration of sulfur compounds is vital in the hydrocarbon processing industry. Gas chromatography with sulfur chemiluminescence detection (GC-SCD) is one of the most powerful tools for sulfur analysis of hydrocarbons. This poster showcases the use of a new SCD for analysis according to various ASTM methods.Similar to Iron-SGS Report.PDF (20)
Tuv ROHS certificate --plastic pneumatic push in fittings
Tuv ROHS certificate --plastic pneumatic push in fittings
Jop description for Senior lab chemist ( shift leader)
Jop description for Senior lab chemist ( shift leader)
Identification and Confirmation of Ten Common Seized Drugs Utilizing a Single...
Identification and Confirmation of Ten Common Seized Drugs Utilizing a Single...
Sulfur Analysis by GC-SCD using Shimadzu’s SCD-2030 for ASTM D5504, D5623, an...
Sulfur Analysis by GC-SCD using Shimadzu’s SCD-2030 for ASTM D5504, D5623, an...
Iron-SGS Report.PDF
- 1. Test Report. No. CANML1620897401 Date: 28 Oct 2016. Page 1 of 4. SONIER PINS CO.,LTD. BLOCK 6-8,NO.16,QINGFENG FIVE ROAD,XIAOLAN TOWN ZHONGSHAN CITY . . The following sample(s) was/were submitted and identified on behalf of the clients as : Fe. SGS Job No. : SZIN1610014166PC - SZ. Client Ref. Info. :. DC01. Date of Sample Received :. 25 Oct 2016. Testing Period :. 25 Oct 2016 - 28 Oct 2016. Test Requested :. Selected test(s) as requested by client.. Please refer to next page(s).. Please refer to next page(s).. Test Method :. Test Results :. Conclusion :. Based on the performed tests on submitted sample(s), the results of Lead, Mercury, Cadmium, Hexavalent chromium comply with the limits as set by RoHS Directive (EU) 2015/863 amending Annex II to Directive 2011/65/EU. . Alkene Liang. Approved Signatory. Signed for and on behalf of SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch.
- 2. Test Report. No. CANML1620897401 Date: 28 Oct 2016. Page 2 of 4. Test Results :. Test Part Description :. Specimen No.. SGS Sample ID. Description. SN1. CAN16-208974.001 Silver-grey metal board. Remarks :. (1) 1 mg/kg = 1 ppm = 0.0001%. (2) MDL = Method Detection Limit. (3) ND = Not Detected ( < MDL ). (4) "-" = Not Regulated. RoHS Directive (EU) 2015/863 amending Annex II to Directive 2011/65/EU. Test Method :. (1)With reference to IEC 62321-5:2013, determination of Cadmium by ICP-OES. (2)With reference to IEC 62321-5:2013, determination of Lead by ICP-OES. (3)With reference to IEC 62321-4:2013, determination of Mercury by ICP-OES. (4)With reference to IEC 62321-7-1:2015 , determination of Hexavalent Chromium by Colorimetric Method using UV-Vis.. 001. Cadmium (Cd). 100 mg/kg. 2 ND Lead (Pb). 1,000 mg/kg. 2 ND Mercury (Hg). 1,000 mg/kg. 2 ND Hexavalent Chromium (Cr(VI))▼. -. µg/cm². 0.10 ND Test Item(s). Limit. Unit. MDL. Notes :. (1) The maximum permissible limit is quoted from RoHS Directive (EU) 2015/863. (2) ▼= a. The sample is positive for CrVI if the CrVI concentration is greater than 0.13 μg/cm2. The sample coating is considered to contain CrVI b. The sample is negative for CrVI if CrVI is ND (concentration less than 0.10 μg/cm2). The coating is considered a non-CrVI based coating c. The result between 0.10 μg/cm2 and 0.13 μg/cm2 is considered to be inconclusive - unavoidable coating variations may influence the determination Information on storage conditions and production date of the tested sample is unavailable and thus Cr(VI) results represent status of the sample at the time of testing. IEC 62321 series is equivalent to EN 62321 series http://www.cenelec.eu/dyn/www/f? p=104:30:1742232870351101::::FSP_ORG_ID, FSP_LANG_ID:1258637,25.
- 3. Test Report. No. CANML1620897401 Date: 28 Oct 2016. Page 3 of 4. ATTACHMENTS Pb/Cd/Hg/Cr6+ Testing Flow Chart 1) Name of the person who made testing: Edith Zhang 2) Name of the person in charge of testing: Bella Wang 3) These samples were dissolved totally by pre-conditioning method according to below flow chart. (Cr6+ test method excluded) Sample Preparation Sample Measurement Acid digestion with microwave/ hotplate Filtration Solution Residue 1) Alkali Fusion / Dry Ashing 2) Acid to dissolve ICP-OES/AAS DATA Nonmetallic material Metallic material Adding digestion reagent Heating to 90~95℃ for extraction Filtration and pH adjustment Adding 1,5- diphenylcarbazide for color development UV-Vis DATA Boiling water extraction Adding 1,5- diphenylcarbazide for color development UV-Vis DATA Pb/Cd/Hg Cr6+
- 4. Test Report. No. CANML1620897401 Date: 28 Oct 2016. Page 4 of 4. Sample photo:. CANML1620897401 CAN16-208974.001. SGS authenticate the photo on original report only. *** End of Report ***.