Introduction about Angle Modulation (FM&PM).pptx
•
0 likes•17 views
The document discusses the benefits of meditation for reducing stress and anxiety. Regular meditation practice can help calm the mind and body by lowering heart rate and blood pressure. Making meditation a part of a daily routine, even if just 10-15 minutes per day, can have mental and physical health benefits over time by helping people feel more relaxed and better able to handle life's stresses.
Report
Share
Report
Share
Recommended
FM-Foster - Seeley Discriminator.pptx
This document discusses the Foster-Seeley phase discriminator, which is a type of frequency discriminator used in FM receivers. It operates by comparing the phase difference between primary and secondary voltages in a transformer tuned to the center frequency. When the input frequency matches the center frequency, the phase difference is 90 degrees and the output is zero. If the input frequency increases or decreases from center, the phase difference changes and a positive or negative output voltage is produced, making it useful for demodulating FM signals. The Foster-Seeley discriminator provides good linearity but requires a transformer and limiter before it.
FM Demodulator Slope Detector.pptx
This document discusses a mathematical formula where Fin is initially set to 0, and variables XL and Xc are also set to 0. Then, Fin is set to its maximum value, XL is set equal to an unknown value, and Xc is set equal to an unknown value. The document also mentions three bullet points but provides no other context or values for the variables.
Generation of DSB-SC using Diode Ring Modulator or chopper Modulator.pptx
This document discusses a ring modulator method for generating a double sideband suppressed carrier (DSB-SC) signal using amplitude modulation. It has advantages like a stable output and not requiring external power. The operation involves using diodes in a ring configuration to selectively pass or block the carrier signal depending on the polarity of the modulating signal. Coherent detection can then be used to recover the message signal from the DSB-SC by synchronizing the local carrier signal.
Generation of AM-DSB-SC using Balanced FET Modulator.pptx
This document discusses amplitude modulation using a balanced FET modulator. It begins by providing the mathematical representation of an AM-DSB-SC waveform. It then describes how a balanced FET modulator can be used to generate an AM-DSB-SC signal. Specifically, it explains that a balanced FET modulator uses two matched FETs in a differential amplifier configuration. The carrier signal is applied in phase to the gates, while the message signal is applied out of phase. This results in an output signal that is amplitude modulated by the message signal. The document concludes by noting that while a balanced FET modulator can heavily suppress the carrier, it cannot achieve 100% carrier suppression due to imperfect matching of the F
Comparison of Amplitude Modulation Techniques.pptx
This document discusses different types of amplitude modulation (AM) used in communication systems. It describes AM-DSB-FC, AM-DSB-SC, AM-SSB-SC, and vestigial sideband modulation (VSB), comparing their objectives to save transmitter power and bandwidth, transmission efficiency, bandwidth, number of channels supported, power consumption, difficulty of reconstruction, and applications. The key objectives of different AM techniques are to optimize power and bandwidth efficiency for various communication modes like radio, telegraphy, telephone and TV.
WSN-Routing Protocols Energy Efficient Routing
Minimize energy per packet (or per bit)
Maximize network lifetime
Routing considering available battery energy
Maximum Total Available Battery Capacity
Minimum Battery Cost Routing (MBCR)
Min– Max Battery Cost Routing (MMBCR)
Conditional Max – Min Battery Capacity Routing (CMMBCR)
Minimize variance in power levels
Minimum Total Transmission Power Routing (MTPR)
Recommended
FM-Foster - Seeley Discriminator.pptx
This document discusses the Foster-Seeley phase discriminator, which is a type of frequency discriminator used in FM receivers. It operates by comparing the phase difference between primary and secondary voltages in a transformer tuned to the center frequency. When the input frequency matches the center frequency, the phase difference is 90 degrees and the output is zero. If the input frequency increases or decreases from center, the phase difference changes and a positive or negative output voltage is produced, making it useful for demodulating FM signals. The Foster-Seeley discriminator provides good linearity but requires a transformer and limiter before it.
FM Demodulator Slope Detector.pptx
This document discusses a mathematical formula where Fin is initially set to 0, and variables XL and Xc are also set to 0. Then, Fin is set to its maximum value, XL is set equal to an unknown value, and Xc is set equal to an unknown value. The document also mentions three bullet points but provides no other context or values for the variables.
Generation of DSB-SC using Diode Ring Modulator or chopper Modulator.pptx
This document discusses a ring modulator method for generating a double sideband suppressed carrier (DSB-SC) signal using amplitude modulation. It has advantages like a stable output and not requiring external power. The operation involves using diodes in a ring configuration to selectively pass or block the carrier signal depending on the polarity of the modulating signal. Coherent detection can then be used to recover the message signal from the DSB-SC by synchronizing the local carrier signal.
Generation of AM-DSB-SC using Balanced FET Modulator.pptx
This document discusses amplitude modulation using a balanced FET modulator. It begins by providing the mathematical representation of an AM-DSB-SC waveform. It then describes how a balanced FET modulator can be used to generate an AM-DSB-SC signal. Specifically, it explains that a balanced FET modulator uses two matched FETs in a differential amplifier configuration. The carrier signal is applied in phase to the gates, while the message signal is applied out of phase. This results in an output signal that is amplitude modulated by the message signal. The document concludes by noting that while a balanced FET modulator can heavily suppress the carrier, it cannot achieve 100% carrier suppression due to imperfect matching of the F
Comparison of Amplitude Modulation Techniques.pptx
This document discusses different types of amplitude modulation (AM) used in communication systems. It describes AM-DSB-FC, AM-DSB-SC, AM-SSB-SC, and vestigial sideband modulation (VSB), comparing their objectives to save transmitter power and bandwidth, transmission efficiency, bandwidth, number of channels supported, power consumption, difficulty of reconstruction, and applications. The key objectives of different AM techniques are to optimize power and bandwidth efficiency for various communication modes like radio, telegraphy, telephone and TV.
WSN-Routing Protocols Energy Efficient Routing
Minimize energy per packet (or per bit)
Maximize network lifetime
Routing considering available battery energy
Maximum Total Available Battery Capacity
Minimum Battery Cost Routing (MBCR)
Min– Max Battery Cost Routing (MMBCR)
Conditional Max – Min Battery Capacity Routing (CMMBCR)
Minimize variance in power levels
Minimum Total Transmission Power Routing (MTPR)
WSN-IEEE 802.15.4 -MAC Protocol
WSN-IEEE 802.15.4 -MAC Protocol
Low Duty Cycle Protocols And Wakeup Concepts –
S-MAC,
The Mediation Device Protocol
Contention based protocols – PAMAS,
Schedule based protocols – LEACH,
IEEE 802.15.4 MAC protocol,
WSN NETWORK -MAC PROTOCOLS - Low Duty Cycle Protocols And Wakeup Concepts – ...
WSN NETWORKING CONCEPTS AND PROTOCOLS
MAC Protocols for Wireless Sensor Networks,
Low Duty Cycle Protocols And Wakeup Concepts –
S-MAC,
WSN network architecture -Sensor Network Scenarios & Transceiver Design Consi...
How to put these nodes together to form a meaningful network.
How a network should function at high-level application scenarios .
On the basis of these scenarios and optimization goals, the design of networking protocols in wireless sensor networks are derived
A proper service interface is required and integration of WSNs into larger network contexts.
AODV (adhoc ondemand distance vector routing)
This document discusses reactive routing protocols in mobile ad hoc networks (MANETs), focusing on the Ad Hoc On-Demand Distance Vector (AODV) protocol. It describes how AODV works by broadcasting Route Request packets when a route is needed, and nodes responding with Route Reply packets if they have a valid route. Intermediate nodes store the address of previous nodes to forward packets. The document outlines the key components of Route Request and Route Reply packets, and notes advantages of AODV such as on-demand route establishment and use of destination sequence numbers, with drawbacks including control overhead and bandwidth consumption from periodic beaconing.
Destination Sequenced Distance Vector Routing (DSDV)
Proactive routing protocol
Each node maintain a routing table.
Sequence number is used to update the topology information
Update can be done based on event driven or periodic
Observations
May be energy expensive due to high mobility of the nodes
Delay can be minimized, as path to destination is already known to all nodes.
Classifications of wireless adhoc networks
Enabling Technologies
Wireless Adhoc Networks (WMN)- (Pure Adhoc consist of stationary nodes )
Mobile Adhoc Networks (MANET)
Vehicular Adhoc Networks (VANET)
Wireless Sensor Networks (WSN)
MANET routing protocols Issues and Classifications
Introduction about routing
Issues in designing a routing protocol
Characteristics of an ideal routing protocol
Classifications of routing protocols
Multimedia Components
The document discusses multimedia components and their characteristics. It defines multimedia as the integration of multiple media forms, including text, graphics, audio, video, and more. The basic elements of multimedia are described as text, images, audio, video, and animation. Digital image representation and processing are also covered, including how images are formed, 1-bit and 8-bit images, and color images. Color images can be represented with 24-bit RGB values or 8-bit color indices mapped to a color lookup table.
New techniques for characterising damage in rock slopes.pdf
rock mass characterization and New techniques for characterising damage in rock slopes
Recycled Concrete Aggregate in Construction Part II
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...University of Maribor
Slides from talk presenting:
Aleš Zamuda: Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapter and Networking.
Presentation at IcETRAN 2024 session:
"Inter-Society Networking Panel GRSS/MTT-S/CIS
Panel Session: Promoting Connection and Cooperation"
IEEE Slovenia GRSS
IEEE Serbia and Montenegro MTT-S
IEEE Slovenia CIS
11TH INTERNATIONAL CONFERENCE ON ELECTRICAL, ELECTRONIC AND COMPUTING ENGINEERING
3-6 June 2024, Niš, SerbiaEric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
this notes have been created
by Eric36 at nyamata ttc
after readings
pe book for y2sme .
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Computational Engineering IITH Presentation
This Presentation will give you a brief idea about what Computational Engineering at IIT Hyderabad has to offer.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
Literature Review Basics and Understanding Reference Management.pptx
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Time Division Multiplexing (TDM) is a method of transmitting multiple signals over a single communication channel by dividing the signal into many segments, each having a very short duration of time. These time slots are then allocated to different data streams, allowing multiple signals to share the same transmission medium efficiently. TDM is widely used in telecommunications and data communication systems.
### How TDM Works
1. **Time Slots Allocation**: The core principle of TDM is to assign distinct time slots to each signal. During each time slot, the respective signal is transmitted, and then the process repeats cyclically. For example, if there are four signals to be transmitted, the TDM cycle will divide time into four slots, each assigned to one signal.
2. **Synchronization**: Synchronization is crucial in TDM systems to ensure that the signals are correctly aligned with their respective time slots. Both the transmitter and receiver must be synchronized to avoid any overlap or loss of data. This synchronization is typically maintained by a clock signal that ensures time slots are accurately aligned.
3. **Frame Structure**: TDM data is organized into frames, where each frame consists of a set of time slots. Each frame is repeated at regular intervals, ensuring continuous transmission of data streams. The frame structure helps in managing the data streams and maintaining the synchronization between the transmitter and receiver.
4. **Multiplexer and Demultiplexer**: At the transmitting end, a multiplexer combines multiple input signals into a single composite signal by assigning each signal to a specific time slot. At the receiving end, a demultiplexer separates the composite signal back into individual signals based on their respective time slots.
### Types of TDM
1. **Synchronous TDM**: In synchronous TDM, time slots are pre-assigned to each signal, regardless of whether the signal has data to transmit or not. This can lead to inefficiencies if some time slots remain empty due to the absence of data.
2. **Asynchronous TDM (or Statistical TDM)**: Asynchronous TDM addresses the inefficiencies of synchronous TDM by allocating time slots dynamically based on the presence of data. Time slots are assigned only when there is data to transmit, which optimizes the use of the communication channel.
### Applications of TDM
- **Telecommunications**: TDM is extensively used in telecommunication systems, such as in T1 and E1 lines, where multiple telephone calls are transmitted over a single line by assigning each call to a specific time slot.
- **Digital Audio and Video Broadcasting**: TDM is used in broadcasting systems to transmit multiple audio or video streams over a single channel, ensuring efficient use of bandwidth.
- **Computer Networks**: TDM is used in network protocols and systems to manage the transmission of data from multiple sources over a single network medium.
### Advantages of TDM
- **Efficient Use of Bandwidth**: TDM all
More Related Content
More from ArunChokkalingam
WSN-IEEE 802.15.4 -MAC Protocol
WSN-IEEE 802.15.4 -MAC Protocol
Low Duty Cycle Protocols And Wakeup Concepts –
S-MAC,
The Mediation Device Protocol
Contention based protocols – PAMAS,
Schedule based protocols – LEACH,
IEEE 802.15.4 MAC protocol,
WSN NETWORK -MAC PROTOCOLS - Low Duty Cycle Protocols And Wakeup Concepts – ...
WSN NETWORKING CONCEPTS AND PROTOCOLS
MAC Protocols for Wireless Sensor Networks,
Low Duty Cycle Protocols And Wakeup Concepts –
S-MAC,
WSN network architecture -Sensor Network Scenarios & Transceiver Design Consi...
How to put these nodes together to form a meaningful network.
How a network should function at high-level application scenarios .
On the basis of these scenarios and optimization goals, the design of networking protocols in wireless sensor networks are derived
A proper service interface is required and integration of WSNs into larger network contexts.
AODV (adhoc ondemand distance vector routing)
This document discusses reactive routing protocols in mobile ad hoc networks (MANETs), focusing on the Ad Hoc On-Demand Distance Vector (AODV) protocol. It describes how AODV works by broadcasting Route Request packets when a route is needed, and nodes responding with Route Reply packets if they have a valid route. Intermediate nodes store the address of previous nodes to forward packets. The document outlines the key components of Route Request and Route Reply packets, and notes advantages of AODV such as on-demand route establishment and use of destination sequence numbers, with drawbacks including control overhead and bandwidth consumption from periodic beaconing.
Destination Sequenced Distance Vector Routing (DSDV)
Proactive routing protocol
Each node maintain a routing table.
Sequence number is used to update the topology information
Update can be done based on event driven or periodic
Observations
May be energy expensive due to high mobility of the nodes
Delay can be minimized, as path to destination is already known to all nodes.
Classifications of wireless adhoc networks
Enabling Technologies
Wireless Adhoc Networks (WMN)- (Pure Adhoc consist of stationary nodes )
Mobile Adhoc Networks (MANET)
Vehicular Adhoc Networks (VANET)
Wireless Sensor Networks (WSN)
MANET routing protocols Issues and Classifications
Introduction about routing
Issues in designing a routing protocol
Characteristics of an ideal routing protocol
Classifications of routing protocols
Multimedia Components
The document discusses multimedia components and their characteristics. It defines multimedia as the integration of multiple media forms, including text, graphics, audio, video, and more. The basic elements of multimedia are described as text, images, audio, video, and animation. Digital image representation and processing are also covered, including how images are formed, 1-bit and 8-bit images, and color images. Color images can be represented with 24-bit RGB values or 8-bit color indices mapped to a color lookup table.
More from ArunChokkalingam (8)
WSN NETWORK -MAC PROTOCOLS - Low Duty Cycle Protocols And Wakeup Concepts – ...
WSN NETWORK -MAC PROTOCOLS - Low Duty Cycle Protocols And Wakeup Concepts – ...
WSN network architecture -Sensor Network Scenarios & Transceiver Design Consi...
WSN network architecture -Sensor Network Scenarios & Transceiver Design Consi...
Destination Sequenced Distance Vector Routing (DSDV)
Destination Sequenced Distance Vector Routing (DSDV)
MANET routing protocols Issues and Classifications
MANET routing protocols Issues and Classifications
Recently uploaded
New techniques for characterising damage in rock slopes.pdf
rock mass characterization and New techniques for characterising damage in rock slopes
Recycled Concrete Aggregate in Construction Part II
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...University of Maribor
Slides from talk presenting:
Aleš Zamuda: Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapter and Networking.
Presentation at IcETRAN 2024 session:
"Inter-Society Networking Panel GRSS/MTT-S/CIS
Panel Session: Promoting Connection and Cooperation"
IEEE Slovenia GRSS
IEEE Serbia and Montenegro MTT-S
IEEE Slovenia CIS
11TH INTERNATIONAL CONFERENCE ON ELECTRICAL, ELECTRONIC AND COMPUTING ENGINEERING
3-6 June 2024, Niš, SerbiaEric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
this notes have been created
by Eric36 at nyamata ttc
after readings
pe book for y2sme .
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Computational Engineering IITH Presentation
This Presentation will give you a brief idea about what Computational Engineering at IIT Hyderabad has to offer.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
Literature Review Basics and Understanding Reference Management.pptx
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Time Division Multiplexing (TDM) is a method of transmitting multiple signals over a single communication channel by dividing the signal into many segments, each having a very short duration of time. These time slots are then allocated to different data streams, allowing multiple signals to share the same transmission medium efficiently. TDM is widely used in telecommunications and data communication systems.
### How TDM Works
1. **Time Slots Allocation**: The core principle of TDM is to assign distinct time slots to each signal. During each time slot, the respective signal is transmitted, and then the process repeats cyclically. For example, if there are four signals to be transmitted, the TDM cycle will divide time into four slots, each assigned to one signal.
2. **Synchronization**: Synchronization is crucial in TDM systems to ensure that the signals are correctly aligned with their respective time slots. Both the transmitter and receiver must be synchronized to avoid any overlap or loss of data. This synchronization is typically maintained by a clock signal that ensures time slots are accurately aligned.
3. **Frame Structure**: TDM data is organized into frames, where each frame consists of a set of time slots. Each frame is repeated at regular intervals, ensuring continuous transmission of data streams. The frame structure helps in managing the data streams and maintaining the synchronization between the transmitter and receiver.
4. **Multiplexer and Demultiplexer**: At the transmitting end, a multiplexer combines multiple input signals into a single composite signal by assigning each signal to a specific time slot. At the receiving end, a demultiplexer separates the composite signal back into individual signals based on their respective time slots.
### Types of TDM
1. **Synchronous TDM**: In synchronous TDM, time slots are pre-assigned to each signal, regardless of whether the signal has data to transmit or not. This can lead to inefficiencies if some time slots remain empty due to the absence of data.
2. **Asynchronous TDM (or Statistical TDM)**: Asynchronous TDM addresses the inefficiencies of synchronous TDM by allocating time slots dynamically based on the presence of data. Time slots are assigned only when there is data to transmit, which optimizes the use of the communication channel.
### Applications of TDM
- **Telecommunications**: TDM is extensively used in telecommunication systems, such as in T1 and E1 lines, where multiple telephone calls are transmitted over a single line by assigning each call to a specific time slot.
- **Digital Audio and Video Broadcasting**: TDM is used in broadcasting systems to transmit multiple audio or video streams over a single channel, ensuring efficient use of bandwidth.
- **Computer Networks**: TDM is used in network protocols and systems to manage the transmission of data from multiple sources over a single network medium.
### Advantages of TDM
- **Efficient Use of Bandwidth**: TDM all
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Advanced control scheme of doubly fed induction generator for wind turbine us...
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
ACEP Magazine edition 4th launched on 05.06.2024
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
Recently uploaded (20)
New techniques for characterising damage in rock slopes.pdf
New techniques for characterising damage in rock slopes.pdf
Recycled Concrete Aggregate in Construction Part II
Recycled Concrete Aggregate in Construction Part II
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Eric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
Eric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Generative AI leverages algorithms to create various forms of content
Generative AI leverages algorithms to create various forms of content
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
Literature Review Basics and Understanding Reference Management.pptx
Literature Review Basics and Understanding Reference Management.pptx
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx