The Sentinel Polished Rod Protection System is a patented PTFE bushing installed in oil wells to centralize the polished rod and prevent metal-to-metal contact and scoring by allowing for fluid bypass. It provides benefits like resistance to chemicals, excellent wear resistance, and prevention of damage to wellhead components. Installation records show that 4 wells installed with the system have seen no polished rod changes since installation, saving operators costs compared to repeated rod changes before installation.
perforated joint, flow coupling and blast jointElsayed Amer
This document discusses perforated joints, flow couplings, and blast joints used in downhole equipment. A perforated joint is installed above a no-go and provides flow bypass when gauges are installed. It must have a total cross-sectional area of holes equivalent to the tubing internal diameter. Flow couplings are installed where turbulence is expected, such as above and below crossovers or nipples, and have thicker walls to prevent early erosion failures. Blast joints are placed near perforations and have heavy, blast-resistant coatings to protect from extreme erosional forces opposite open perforations.
The document discusses various types of production packers used in well completion and intervention work. It describes packers that can be set mechanically, hydraulically, or electrically and covers single bore, dual bore, sump, and ESP packers. The purposes of packers include isolating zones, facilitating gas lift, preventing fluid flow, and testing or abandoning wells. Packer setting mechanisms, components, and installation procedures are also outlined.
Pilgrim International produces shaft coupling solutions including radial fit bolts. Their radial fit bolts can be installed and removed in 10-15 minutes, faster than traditional shrink fit bolts which require freezing. Radial fit bolts provide a secure, pre-engineered interference fit between coupling flanges with lower lifetime costs than shrink fit bolts which frequently cause damage upon removal.
This document is a catalog of products from Systhex, a Brazilian dental implant company. It includes information on dental implants, prosthetic components, surgical instruments and kits. Implant types include internal hex, external hex, cone morse, and short implants. Prosthetic components allow for cement-retained and screw-retained restorations. The catalog also provides technical specifications and codes for each item.
The document proposes developing a Tek-Belt device to improve the process of installing Tek-screws. Currently, installing Tek-screws involves manually loading each screw into a drill bit, which is time-consuming and requires two hands. The proposed Tek-Belt would allow screws to feed continuously from a belt into the drill bit, enabling one-handed operation and faster installation. The design concepts and initial prototype are presented, along with recommendations to refine the device.
Wear and spare parts are at the heart of BOGVIK business and we are continually driven to find new and improved ways to optimize component life and equipment performance.
We believe in collaboration and work hand-in-hand with our customers to develop solutions that leverages our practical experience, in-house engineering & metallurgical capabilities and manufacturing capacity to provide a complete solution that meets our customer needs.
Contact us today to see how we can help extend service life, improve throughput, optimize supply chain and reduce the total cost of ownership.
perforated joint, flow coupling and blast jointElsayed Amer
This document discusses perforated joints, flow couplings, and blast joints used in downhole equipment. A perforated joint is installed above a no-go and provides flow bypass when gauges are installed. It must have a total cross-sectional area of holes equivalent to the tubing internal diameter. Flow couplings are installed where turbulence is expected, such as above and below crossovers or nipples, and have thicker walls to prevent early erosion failures. Blast joints are placed near perforations and have heavy, blast-resistant coatings to protect from extreme erosional forces opposite open perforations.
The document discusses various types of production packers used in well completion and intervention work. It describes packers that can be set mechanically, hydraulically, or electrically and covers single bore, dual bore, sump, and ESP packers. The purposes of packers include isolating zones, facilitating gas lift, preventing fluid flow, and testing or abandoning wells. Packer setting mechanisms, components, and installation procedures are also outlined.
Pilgrim International produces shaft coupling solutions including radial fit bolts. Their radial fit bolts can be installed and removed in 10-15 minutes, faster than traditional shrink fit bolts which require freezing. Radial fit bolts provide a secure, pre-engineered interference fit between coupling flanges with lower lifetime costs than shrink fit bolts which frequently cause damage upon removal.
This document is a catalog of products from Systhex, a Brazilian dental implant company. It includes information on dental implants, prosthetic components, surgical instruments and kits. Implant types include internal hex, external hex, cone morse, and short implants. Prosthetic components allow for cement-retained and screw-retained restorations. The catalog also provides technical specifications and codes for each item.
The document proposes developing a Tek-Belt device to improve the process of installing Tek-screws. Currently, installing Tek-screws involves manually loading each screw into a drill bit, which is time-consuming and requires two hands. The proposed Tek-Belt would allow screws to feed continuously from a belt into the drill bit, enabling one-handed operation and faster installation. The design concepts and initial prototype are presented, along with recommendations to refine the device.
Wear and spare parts are at the heart of BOGVIK business and we are continually driven to find new and improved ways to optimize component life and equipment performance.
We believe in collaboration and work hand-in-hand with our customers to develop solutions that leverages our practical experience, in-house engineering & metallurgical capabilities and manufacturing capacity to provide a complete solution that meets our customer needs.
Contact us today to see how we can help extend service life, improve throughput, optimize supply chain and reduce the total cost of ownership.
This document discusses well completion design, selection, and operations. It provides an overview of the sequence of well drilling and completion. It describes common casing programs and marks the starting point of completion. It also details the metals commonly used in completion equipment and describes various downhole completion tools like tubing hangers, packers, and wireline entry guides.
Oetiker product range and solutions for the commercial and industrial vehicles industry sector. Exhaust, turbo, thermal management, tank straps applications along with assembly solutions.
Revolvo Split Roller Bearings (SRBs) have been designed and developed to maximise service life and minimise maintenance effort.
The complete range of Split Roller Bearings incorporate a number of innovative features that assist the user in terms of performance and assembly.
Machined brass cage as standard
Robust support design
Profiled rolling elements
Light, medium and heavy series
Comprehensive range of supports
NeOz Energy manufactures oilfield equipment used in various drilling stages, including float equipment, cementing plugs, and other tools. They specialize in high quality products like float shoes, collars, and cementing plugs. NeOz prides itself on its quality control processes and certifications to ISO and API standards to ensure product reliability. They aim to deliver products globally within 48 hours through their wide network of agents and distributors.
This document contains information about Eng. El Sayed Amer, a petroleum engineer who has worked for Weatherford Drilling International and as a process and production engineer for SUCO and RWE DEA. It discusses production packers, which are subsurface tools used to provide a seal between the tubing and casing. Production packers can protect the casing from corrosion, provide better well control, isolate pay zones, and prevent fluid movement between zones. They are classified as either permanent or retrievable based on whether they can be removed from the well without destruction. The document focuses on the characteristics and advantages and disadvantages of permanent and retrievable production packers.
Well completion equipment 2. landing nipplesElsayed Amer
A landing nipple is a short length of pipe with a cut profile on the inside used to allow a lock mandrel to locate and lock into for various purposes like plugging the tubing. There are selective and no-go types, with no-go containing a restriction preventing passage. Landing nipples are used for removing surface equipment, pressure testing, setting packers, installing downhole tools, and landing pressure recorders. They consist of a lock mandrel, equalizing sub, and flow control device. Major manufacturers include Baker, CAMCO, Halliburton, and Weatherford.
Hal demonstrates how the flexible-lip DOUBLE-SEAL design of JAMESBURY ball valves works under extreme pressure to provide a bubble-tight shut-off that exceeds industry standards, convincing everyone present. The unique design and XTREME sealing technology provide reliable operation in a wide range of temperatures and pressures. JAMESBURY valves provide trouble-free operation and uptime that is longer than any other valve.
This document provides specifications for a peripheral stent graft system, including:
- The graft material is micro-porous ePTFE tubing that is 102 ± 25μm
- The stent material is CoCr alloy with strut dimensions ranging from 0.135 x 0.145 mm to 0.165 x 0.145 mm depending on location
- It has a 6F or 7F introducer sheath compatibility, 0.035” guidewire, and balloon marker made of platinum/iridium
- Nominal stent diameters range from 5.0mm to 10.0mm and lengths range from 18mm to 58mm depending on location
- The system has a 3 year shelf life and is
Bourgault Tillage Tools has been innovating tillage and seeding tools for over 25 years based on farming experience. They introduced the Speed-Loc system 12 years ago, which allows quick changing of points and adapts to most cultivator tines. It provides benefits like fast changing, consistent depth, and durability. The system can be used with a range of sweep points and seeding boots to configure drills for different crops.
This document discusses side sliding doors and side pocket mandrels. Side sliding doors, also known as sliding sleeves, are used to provide controlled communication between the tubing and casing annulus. They can enable well killing by fluid circulation. Side pocket mandrels are used to install gas lift valves, dummies, or chemicals at intervals along the tubing string. Gas is injected into the tubing/casing annulus and acts on the gas lift valves to lift liquid up the tubing.
This document provides information about side sliding doors (SSDs), including:
1) SSDs are also known as sliding sleeves that provide controlled communication between the tubing and casing annulus.
2) SSDs can be used for applications like fluid displacement, well killing, gas lifting, and chemical injection by opening or closing ports between the annulus and tubing.
3) SSD sleeves can be shifted using wireline methods, coiled tubing methods, pressure darts, or differential pressure application to the annulus.
Thermography Presentation - Excavator and face shovel presentationVikingServices
Viking Mining Services provides thermography inspection services for hydraulic excavators and face shovels to identify potential issues. Thermography allows them to monitor machines from a distance to detect anomalies safely. Some examples include identifying a problem with an excavator stick and bucket pin and bush from 100 meters away, saving the client $30,000 from avoiding an early failure. Viking's services help clients increase safety and production while decreasing downtime through early problem detection without disrupting work.
We are one of the best rubber bellow mechanical seal manufacturers and suppliers and also We provide the rubber bellows seal with very high mechanical strength.The rubber bellow type mechanical seal are trouble-free to install and very easy to remove.
Total chain solutions - diamond cutting chains & accessories for cutting pip...Yan Mashov
High Quality Chains
SUPERIOR PERFORMANCE LASER WELDED DIAMOND CHAIN FOR:
General building materials
Firebrick/ Refractories
Reinforced concrete
Stone /Granite
Block/ Sandstone/ Abrasive materials
Coal
Building Bricks
Ductile iron/ Cast iron/ PVC/ HDPE
SPEED – 25% faster than others.
LIFE SPAN – 25% longer life span than others.
IMPROVED USER EXPERIENCE – On each link there is a segment providing smoother cutting and higher output. Diamond segment on each link providing smoother cutting, higher output and less vibration.
BULK CONCEPT – Efficient stock management solution: cut to size and repair capability.
COMPLETE KIT – Provides a compatible answer for most common chain cutting machines.
ACCESSORIES – Compatible high quality guide bars, sprockets and chain parts.
TECHNICAL SUPPORT – Direct from the manufacturer.
The document discusses the use of Weatherford's BULLDOG ACP annulus casing packer to mitigate fluid losses and enable a successful cementing operation during the completion of an onshore development well in Ahmedabad, India. The packer was set to seal the annulus and hold the cement in place. This allowed the operator to cement the well with no stability issues, avoiding additional cementing jobs and improving well safety.
Sasa Surlan Report 22-12-2013_08-01-2014Sasa Surlan
The daily report summarizes maintenance and repair work done on an offshore oil rig between December 22nd and January 8th. Key activities included:
- Rebuilding lower choke valves and performing maintenance on a transporter.
- Opening bonnets and performing inspections on various ram blocks. Shuttle and seals were replaced.
- Cleaning and dimensional checks of ram cavities. NDT inspections were conducted.
- Troubleshooting electrical issues with a BOP hydraulic power unit mix tank. Surface accumulators were pre-charged.
- Replacing seals in a lower isolation valve and commissioning a ROMAR control panel. Welding alterations were started on a dynamic seal assembly.
-
1. sequance of well drilling and completion part 1Elsayed Amer
The document outlines the steps for well drilling and site preparation. It describes leveling the site, digging a cellar and mud pits, hammering a conductor pipe, drilling a rathole, and transporting equipment to the site. Subsequent steps include rig setup, inspection and preparation of drill pipes and drill string, mixing and pumping spud mud, drilling initial sections, cleaning the hole, running and cementing surface casing.
WOM Group, a leading Plug Valves Manufacturer offers a wide range of Model 700 Plug Valves products. Model 700 Plug Valve is a tapered seal, lubricated, quarter-turn plug valve for rapid operation in both onshore and offshore applications.
Project Sales Corporation distributes tools manufactured by Gearench for various industries including oil, gas, mining, and utilities. Gearench was founded in 1927 in Houston, Texas and has developed over 40 product lines for applications in exploration, drilling, production, refining, and completion within the oil industry. The document describes several wrench products distributed in India including the Titan Refinery Wrench for refineries and gas processing, Titan Valve Wheel Wrenches, Petol SurGrip Valve Wheel Wrenches, and Titan 100 Series aluminum valve wheel wrenches. Pricing information is provided for each product line.
The document describes KEE GATE self-closing safety gates that provide hazard protection for internal and external applications. The gates are spring-loaded to automatically close behind users and comply with European and American safety standards. They have undergone extensive life cycle and corrosion testing to ensure durability. KEE GATE can accommodate openings up to 1m and is supplied galvanized or powder coated in safety yellow.
This document discusses well completion design, selection, and operations. It provides an overview of the sequence of well drilling and completion. It describes common casing programs and marks the starting point of completion. It also details the metals commonly used in completion equipment and describes various downhole completion tools like tubing hangers, packers, and wireline entry guides.
Oetiker product range and solutions for the commercial and industrial vehicles industry sector. Exhaust, turbo, thermal management, tank straps applications along with assembly solutions.
Revolvo Split Roller Bearings (SRBs) have been designed and developed to maximise service life and minimise maintenance effort.
The complete range of Split Roller Bearings incorporate a number of innovative features that assist the user in terms of performance and assembly.
Machined brass cage as standard
Robust support design
Profiled rolling elements
Light, medium and heavy series
Comprehensive range of supports
NeOz Energy manufactures oilfield equipment used in various drilling stages, including float equipment, cementing plugs, and other tools. They specialize in high quality products like float shoes, collars, and cementing plugs. NeOz prides itself on its quality control processes and certifications to ISO and API standards to ensure product reliability. They aim to deliver products globally within 48 hours through their wide network of agents and distributors.
This document contains information about Eng. El Sayed Amer, a petroleum engineer who has worked for Weatherford Drilling International and as a process and production engineer for SUCO and RWE DEA. It discusses production packers, which are subsurface tools used to provide a seal between the tubing and casing. Production packers can protect the casing from corrosion, provide better well control, isolate pay zones, and prevent fluid movement between zones. They are classified as either permanent or retrievable based on whether they can be removed from the well without destruction. The document focuses on the characteristics and advantages and disadvantages of permanent and retrievable production packers.
Well completion equipment 2. landing nipplesElsayed Amer
A landing nipple is a short length of pipe with a cut profile on the inside used to allow a lock mandrel to locate and lock into for various purposes like plugging the tubing. There are selective and no-go types, with no-go containing a restriction preventing passage. Landing nipples are used for removing surface equipment, pressure testing, setting packers, installing downhole tools, and landing pressure recorders. They consist of a lock mandrel, equalizing sub, and flow control device. Major manufacturers include Baker, CAMCO, Halliburton, and Weatherford.
Hal demonstrates how the flexible-lip DOUBLE-SEAL design of JAMESBURY ball valves works under extreme pressure to provide a bubble-tight shut-off that exceeds industry standards, convincing everyone present. The unique design and XTREME sealing technology provide reliable operation in a wide range of temperatures and pressures. JAMESBURY valves provide trouble-free operation and uptime that is longer than any other valve.
This document provides specifications for a peripheral stent graft system, including:
- The graft material is micro-porous ePTFE tubing that is 102 ± 25μm
- The stent material is CoCr alloy with strut dimensions ranging from 0.135 x 0.145 mm to 0.165 x 0.145 mm depending on location
- It has a 6F or 7F introducer sheath compatibility, 0.035” guidewire, and balloon marker made of platinum/iridium
- Nominal stent diameters range from 5.0mm to 10.0mm and lengths range from 18mm to 58mm depending on location
- The system has a 3 year shelf life and is
Bourgault Tillage Tools has been innovating tillage and seeding tools for over 25 years based on farming experience. They introduced the Speed-Loc system 12 years ago, which allows quick changing of points and adapts to most cultivator tines. It provides benefits like fast changing, consistent depth, and durability. The system can be used with a range of sweep points and seeding boots to configure drills for different crops.
This document discusses side sliding doors and side pocket mandrels. Side sliding doors, also known as sliding sleeves, are used to provide controlled communication between the tubing and casing annulus. They can enable well killing by fluid circulation. Side pocket mandrels are used to install gas lift valves, dummies, or chemicals at intervals along the tubing string. Gas is injected into the tubing/casing annulus and acts on the gas lift valves to lift liquid up the tubing.
This document provides information about side sliding doors (SSDs), including:
1) SSDs are also known as sliding sleeves that provide controlled communication between the tubing and casing annulus.
2) SSDs can be used for applications like fluid displacement, well killing, gas lifting, and chemical injection by opening or closing ports between the annulus and tubing.
3) SSD sleeves can be shifted using wireline methods, coiled tubing methods, pressure darts, or differential pressure application to the annulus.
Thermography Presentation - Excavator and face shovel presentationVikingServices
Viking Mining Services provides thermography inspection services for hydraulic excavators and face shovels to identify potential issues. Thermography allows them to monitor machines from a distance to detect anomalies safely. Some examples include identifying a problem with an excavator stick and bucket pin and bush from 100 meters away, saving the client $30,000 from avoiding an early failure. Viking's services help clients increase safety and production while decreasing downtime through early problem detection without disrupting work.
We are one of the best rubber bellow mechanical seal manufacturers and suppliers and also We provide the rubber bellows seal with very high mechanical strength.The rubber bellow type mechanical seal are trouble-free to install and very easy to remove.
Total chain solutions - diamond cutting chains & accessories for cutting pip...Yan Mashov
High Quality Chains
SUPERIOR PERFORMANCE LASER WELDED DIAMOND CHAIN FOR:
General building materials
Firebrick/ Refractories
Reinforced concrete
Stone /Granite
Block/ Sandstone/ Abrasive materials
Coal
Building Bricks
Ductile iron/ Cast iron/ PVC/ HDPE
SPEED – 25% faster than others.
LIFE SPAN – 25% longer life span than others.
IMPROVED USER EXPERIENCE – On each link there is a segment providing smoother cutting and higher output. Diamond segment on each link providing smoother cutting, higher output and less vibration.
BULK CONCEPT – Efficient stock management solution: cut to size and repair capability.
COMPLETE KIT – Provides a compatible answer for most common chain cutting machines.
ACCESSORIES – Compatible high quality guide bars, sprockets and chain parts.
TECHNICAL SUPPORT – Direct from the manufacturer.
The document discusses the use of Weatherford's BULLDOG ACP annulus casing packer to mitigate fluid losses and enable a successful cementing operation during the completion of an onshore development well in Ahmedabad, India. The packer was set to seal the annulus and hold the cement in place. This allowed the operator to cement the well with no stability issues, avoiding additional cementing jobs and improving well safety.
Sasa Surlan Report 22-12-2013_08-01-2014Sasa Surlan
The daily report summarizes maintenance and repair work done on an offshore oil rig between December 22nd and January 8th. Key activities included:
- Rebuilding lower choke valves and performing maintenance on a transporter.
- Opening bonnets and performing inspections on various ram blocks. Shuttle and seals were replaced.
- Cleaning and dimensional checks of ram cavities. NDT inspections were conducted.
- Troubleshooting electrical issues with a BOP hydraulic power unit mix tank. Surface accumulators were pre-charged.
- Replacing seals in a lower isolation valve and commissioning a ROMAR control panel. Welding alterations were started on a dynamic seal assembly.
-
1. sequance of well drilling and completion part 1Elsayed Amer
The document outlines the steps for well drilling and site preparation. It describes leveling the site, digging a cellar and mud pits, hammering a conductor pipe, drilling a rathole, and transporting equipment to the site. Subsequent steps include rig setup, inspection and preparation of drill pipes and drill string, mixing and pumping spud mud, drilling initial sections, cleaning the hole, running and cementing surface casing.
WOM Group, a leading Plug Valves Manufacturer offers a wide range of Model 700 Plug Valves products. Model 700 Plug Valve is a tapered seal, lubricated, quarter-turn plug valve for rapid operation in both onshore and offshore applications.
Project Sales Corporation distributes tools manufactured by Gearench for various industries including oil, gas, mining, and utilities. Gearench was founded in 1927 in Houston, Texas and has developed over 40 product lines for applications in exploration, drilling, production, refining, and completion within the oil industry. The document describes several wrench products distributed in India including the Titan Refinery Wrench for refineries and gas processing, Titan Valve Wheel Wrenches, Petol SurGrip Valve Wheel Wrenches, and Titan 100 Series aluminum valve wheel wrenches. Pricing information is provided for each product line.
The document describes KEE GATE self-closing safety gates that provide hazard protection for internal and external applications. The gates are spring-loaded to automatically close behind users and comply with European and American safety standards. They have undergone extensive life cycle and corrosion testing to ensure durability. KEE GATE can accommodate openings up to 1m and is supplied galvanized or powder coated in safety yellow.
OES offers a range of oil rig equipment inspection, audit, and project services through their three divisions: OES Special Services, OES International, and OES Regional. With offices globally, OES has dedicated technical experts to deliver inspection, non-destructive testing, auditing, and project management services. Their services include hazardous area surveys, infrared thermography, vibration analysis, rig inspections, non-destructive testing, auditing, and project support.
The document is a project schedule for MEP works at the CICPA Qusahwira Complex in the United Arab Emirates. It details the engineering, shop drawings, material approval, and construction completion milestones for various buildings and components of the project. The schedule shows the original and remaining duration of tasks, as well as budgeted costs, actual costs incurred to date, and percentage of completion for the overall project and its sub-projects. The project is currently 42.76% complete and expected to be finished by July 2016.
Farewell, Land of Cronyism and IncompetencePo' Peasant
The document summarizes the author's experience trying to build a career in graphic design in Boston over nearly 20 years. They took secretarial jobs at first, hoping for advancement, but found themselves stuck in low-level clerical work. They went back to school for graphic design but continued struggling to find permanent work, usually doing temporary contracts. After many rejections on job applications and short-term positions ending, they have concluded that Boston is truly a place of "cronyism and incompetence" and that moving there was a major mistake that ruined their career prospects.
This short document contains credits for five different photos used in a presentation, attributed to photographers from NASA's Marshall Space Flight Center, NASA Goddard Photo and Video, and Gray Lensman QX. The document concludes by encouraging the reader to create their own presentation on SlideShare.
Technovision Pipe Joint System is an ideal material handling system that is wisely designed for all industries’ material handling needs. It is smart, dynamic and flexible.
Technovision Engineers Pvt. Ltd. Manufacturer & Supplier of a wide range of products which include ABS Coated Pipe such as Stainless Steel Pipe, Conductive Pipe, Slide pipe and Anti static color pipe.
Technovision Engineers Pvt. Ltd. is a leading manufacturer of material handling equipment such as pallets, trolleys, pipes, and joints. The company has two manufacturing facilities totaling 28,000 square feet and offers a wide range of products. It prides itself on superior quality, customer service, and innovation through constant R&D. Over the years, the company has expanded its operations and product portfolio, and received several certifications for its quality systems and processes. Technovision Engineers aims to provide customized lean manufacturing solutions through state-of-the-art designs.
This document provides information on various mechanical rebar splicing systems produced by Moment, including:
- Barbreak couplers which use tapered threads for easy alignment and achieve full strength with 4-5 turns.
- Jointec couplers which ensure full strength splicing through parallel threads and behave as continuous reinforcement.
- Reverse lock couplers which are designed for heavily congested areas and connect bent bars.
- Positioning couplers which are used when bars cannot rotate and comprise three components to connect non-rotating bars.
Technical specifications and installation procedures are provided for each coupler type. The couplers are designed to exceed requirements of international codes and provide alternatives to traditional lap splicing.
This document provides information on various mechanical rebar splicing systems produced by Moment, including:
- Barbreak, JoinTec, Reverse Lock, and Positioning couplers, which join rebar using threaded connections and are designed to withstand breaking loads of at least 700 N/mm2.
- Details on the components, features, and installation procedures for each coupler type.
- The couplers exceed requirements of various international codes and standards and offer benefits like increased strength, reduced congestion, and easier installation compared to lap splicing.
The plumbing system is composed of two separate subsystems. One subsystem brings fresh water in, and another takes the wastewater out. In the plumbing system, the pipe used to transport potable drinking water usually use different materials from the pipe carrying drain water. The different regions also have differences in pipe material and size. Your plumbing system may contain one or several types of pipe.
Due to the complicated pipe and fitting standards, plumbing used to be limited to professionals. But the availability of a wide range of plumbing tools has allowed everyone to redo the pipe without any permit or training.
There are four methods through which you can get the work done:
1.Crimping
2.Pressing
3.Clamp
4.Expansion
5.Push to Connect
Focused heavily on providing people professional and affordable plumbing tools, IWISS spent a lot on R&D. For past decades, our company has worked across a variety of plumbing tools, which cover all five methods and meet the standards from the imperial system to the metric system. Our product line also includes pipe cutters, decrimping tools, and chamfer, offering more possibilities in pipe prefabrication. Not only in providing the single tool, but we also have professional a comprehensive, and high-performance, up-gradable tool kit for installing and maintaining today’s and tomorrow’s plumbing system.
provided on the valve body to
This document discusses Expert Knife Gate Valves manufactured by EXPERT, an Indian company established in 1981. It provides an overview of the company's strengths including its experience, product range, manufacturing capabilities, and customer-focused approach. The document then describes features and applications of Expert Knife Gate Valves, which are designed for isolation, on-off, and throttling applications in industries such as pulp and paper, cement, mining, and more. Technical details are also provided on valve body materials and construction, gates, stems, glands, and available actuators.
This document provides information on John Guest fittings and related products. It specifies that John Guest fittings are designed to technical specifications outlined in John Guest catalogues and should be selected, installed, used and maintained according to these specifications. It is the customer's responsibility to ensure fittings are suitable for their intended use and installed correctly. Speedfit should not be used for gas, fuel, or compressed air applications. The document also provides contact information for John Guest.
Multi Service High Pressure Ball Valves : SERIES - BV105Ljackmethyu
SEALEXCEL Valve offers high pressure ball valves suitable for applications where the medium is flowing at a pressure greater than 3000 psi
https://www.sealexcel.com/instrumentation-valves/
Cashco manufactures a broad line of throttling rotary and
linear control valves, pressure reducing regulators, and
back pressure regulators in line sizes from 1⁄4 inch to
10 inches and Cv ranges from .002 to 4,406. Models
are available to handle slurries, cryogenic service, and
corrosive fluids; to withstand high temperatures and
pressures; and to maximize the reduction of fugitive
emissions. Contact Cashco for complete product information.
PTI Corp is a global manufacturer and supplier of power transmission and motion control products headquartered in Charlotte, NC. They offer a wide range of mounted ball bearings, drive products, and linear components. Their products include mounted ball bearings in both American standard and European housings available with different insert types like set screw, eccentric collar, and adapter mounting. They also offer these products in materials like cast iron, ductile iron, stainless steel, and thermoplastic.
Concentric type of butterfly valve is widely used for various applications. From Wafer to Lug, Flange, Universal, U section or AWWA types are all upon on request.
Prevent the formation of lug wear. Lug wear leads to equipment
breakdown, which results in downtime, production shortfalls and in the worst case scenario, injury. Construction, mining and forestry companies across the globe need a solution that permanently eliminates lug wear and empowers them to meet the challenges of everyday industrial operations. Expander System is on a mission to reset the limits of industrial operations.
Because of their structural design, trunnion mount ball valves are suitable for all pressure ranges and sizes.They are used by many manufacturers as a basis of design for their severe service ball valve offerings. A trunnion mount ball valve can also be advantageous for applications employing valve automation. Since the ball is not held in place by a tight fitting seal arrangement, operating torque tends to be lower for comparably sized trunnion valves, when compared to floating ball valves.
How to Improve Steam Turbine Head Rate and Increase OutputMargaret Harrison
As the steam path degrades in mature steam turbines performance loss often occurs. Reducing heat rate while increasing output can have a significant impact on earning potential within the current market and today’s regulatory conditions. Improvements of 3% or more have been seen by users who have installed the full package of steam turbine seals in their units. EthosEnergy has been developing advanced turbine sealing technologies that improve efficiency and performance of steam turbines for over 30 years.
This document provides information on Pilgrim International Limited, a company that designs and manufactures hydraulic bolting solutions. It discusses Pilgrim's history of innovation over 60+ years, their product offerings including hydraulic radial fit bolts and coupling hole alignment tools, benefits of their bolting systems, life cycle cost savings, installation/removal processes, and technical specifications. It aims to showcase Pilgrim as the global leader in hydraulic bolting technology for industries such as power, marine, oil/gas, and more.
SEALEXCEL’s total quality system and control from incoming raw material inspecon through ongoing quality assurance during producon, final inspecon, assembly, tesng, packing and dispatch ensure high standard quality products which has earned us various quality cerficaons
https://www.sealexcel.com/instrumentation-fittings/
This document provides an overview of spare parts and services offered by SKT Textile for various textile machinery. It lists parts available for blowroom, carding, draw frame, combing preparatory, comber, and ringframe equipment from manufacturers like Rieter, LMW, Trutzschler, and others. Parts include conveyor belts, chains, gears, cylinders, rollers, and more. The document emphasizes that SKT parts are of OEM quality and offers replacement warranties for parts.
2. 1
What is it?
The SENTINEL Polished Rod Protection System is a revolutionary
patent pending PTFE (Teflon) bushing that is installed into the tubing
hanger and onto the polished rod inside a producing wellhead below
all surface control and prevention components of the wellhead
assembly yet allows for equipment to be run through without
problems.
It provides centralization for the polished rod to prevent metal to
metal contact with the production tubing below the tubing hanger. It
also provides support for the polished rod to prevent side loading the
stuffing box and premature wear of the stuffing box packing elements.
The system is comprised of two parts, SLEEVE and INSERT BUSHING,
which are matched to the production tubing ID, tubing hanger ID, BHP
and polished rod OD.
Benefits and Properties
• Virtually resistant to all chemicals.
• Excellent wear resistance and provides a low coefficient of friction.
• Will not damage wellhead or production components
• Very wide temperature range to allow for servicing the well without
damaging the bushing (-73°C to 204°C).
• Helical fluting allows for production fluid by-pass without high
pressure differentials (144m³/day with 100kPa differential), and
allows for polished rod supporting on the full length of the bushing.
• Cost effective repair for polished rod scoring and premature and
excessive packing wear
• Low cost initial install to prevent polished rod scoring from time of
initial completion through the life of the well.
3. 2
Available sizes
Sleeve part number and sizes:
TPGS-6030-4800 – 60.3mm (2.375”) EUE X 48mm seating bore
TPGS-7300-4800 – 73.0mm (2.875”) EUE X 48mm seating bore
TPGS-7300-6000 – 73.0mm (2.875”) EUE X 60mm seating bore
TPGS-8890-4800 – 88.9mm (3.50”) EUE X 48mm seating bore
TPGS-8890-6000 – 88.9mm (3.50”) EUE X 60mm seating bore
TPGS-8890-7200 – 88.9mm (3.50”) EUE X 72mm seating bore
Insert Bushing part number and sizes
TPGI-4800-3175 – 48mm X 32mm (1.25”) rod bore
TPGI-6000-3175 – 60mm X 32mm (1.25”) rod bore
TPGI-6000-3800 – 60mm X 38mm (1.50”) rod bore
TPGI-7200-3175 – 72mm X 32mm (1.25”) rod bore
TPGI-7200-3800 – 72mm X 38mm (1.50”) rod bore
TPGI-7200-4450 – 72mm X 44.5mm (1.75”) rod bore
**Custom sizes and threading available to customer request
Other available services
We are IRP #7 compliant and can complete your installation by
organizing the crews, performing the installation and returning the
well back to operations. We have 30 years oilfield experience
including wellsite supervision for completions, work-overs,
production work. We also have extensive experience in downhole tool
installation and pumping / stimulation experience.
4. 3
History
While attempting to fix a well with major polished rod scoring, it was
found that the surface wellhead equipment was not square to the sub-
surface tubulars. This created a deviation between the wellhead and
the sub-surface production tubing. The pumpjack is designed to
stroke the polished rod in a true vertical fashion. This minor deviation
at ground level was found to be approximately 3.0°. Other installs
were found to have slightly less of a deviation (+/-1°) depending on
well design for possible polished rod contact. Another factor into
some of the scoring issues was pumpjack alignment and sometimes
both.
Over the length of the polished rod, while the pumpjack was stroking
the rod string, at the bottom of the rod stroke the polished rod was
>8m below the stuffing box. The space between the OD of the polished
rod and the ID of the tubing was reduced to nil as the polished rod
was no longer running true vertical below ground but trying to run in-
line with the deviation, creating metal to metal contact and polished
rod scoring.
All available sucker rod centralizing equipment was used in an
attempt to solve the problem with the scoring to no avail. Through
trial and error on many wells it was also found that after the initial
start-up, there were no signs of polished rod scoring and it was not
long before the scoring started to become evident. On inspection of
the pony rods below the polished rod it was found that the guides
were worn to the point that the polished rod was able to contact the
production tubing ID creating the score.
The SENTINEL Polished Rod Protection System was conceived,
prototyped and installed to prevent the scoring on some major
problem wells to test the viability of the system and continues to
perform above expectation. It is a valuable piece of affordable
equipment that can be installed into the wellhead at the start of the
well. Prevention rather than reaction is always more cost effective.
5. 4
Installation History
Well #1 – Major polished rod scoring issues. Multiple polished rod
changes, wellhead and pumpjack realignment as well as sucker rod
centralization equipment used prior to SENTINEL install.
Date of well startup – Jan/13,
Date of SENTINEL Install - July/15, >1 year in service
Polished rods changed prior to SENTINEL install = 8,
Approximate cost >$1M
Polished rods changed since SENTINEL install = 0
Well#2 – New well that began to score shortly after well had been
producing.
Date of well startup – Nov/14
Date of SENTINEL install – Jan/15, 8 months in service
Polished rods changed prior to SENTINEL install = 3
Approximate cost <$30K
Polished rods changed since SENTINEL install = 0
Well #3 – New well that scored the polished rod within the first hour
of production.
Date of startup – Jan/15
Date of SENTINEL install – Jan/15, 8 months in service
Polished rods changed prior to SENTINEL install=1
Approximate cost <$10K
Polished rods changed since SENTINEL install = 0
Well #4 – Problem well that had numerous work-overs to attempt to
solve the scoring issue. Two joints larger tubing ran at surface to
attempt to allow more clearance between the polished rod OD and the
tubing ID.
Date of startup – Mar/13
Date of SENTINEL install – Jun/15, < 3 months in service
Polished rod changed prior to SENTINEL install = 7
Approximate cost >$90K
Polished rods changed since SENTINEL install = 0
6. 5
In 4 wells, if the SENTINEL Polished Rod Protection System had been
available and installed it could have saved the prime contractor large
amount of downtime and costs.
Historically it has been found that mobilizing crews to perform one
polished rod change in a day ranges $10,000 - $17,000 depending if
your BHP has to be tripped out of the well due to seizing or other
potential problems with unseating and extent of damaged sucker rod
equipment.
Other benefits
The SENTINEL Polished Rod Protection System not only protects the
polished rod, which is the most expensive of the rods installed into the
well, but while the polished rod is being centralized at the tubing
hanger, it is also providing centralization up through the wellhead and
stuffing box alleviating side loading of the stuffing box elements,
which save the operator field maintenance costs down the road in
terms of stuffing box packing changes and crews to perform the
changes.
Operators have the chance to save big costs with one affordable
install, as one system install saves $10,000 - $17,000 on one scored
polished rod. The SENTINEL Polished Rod Protection System then
becomes a valuable asset in the design of the wellhead, pump and
rods.
After the SENTINEL Polished Rod Protection System install, the
“insert bushing” is the only component that would require
replacement after it wears down to the wear indicators. The wear
indicators were designed and implemented to allow operators, during
their runs, to visually inspect the polished rod for indications of a
vertical brass discoloration on the polished rod from the indicators, as
this is the only way to tell whether the insert bushing is wearing out.
The cost of replacing an insert bushing costs considerably less than
changing a polished rod.
7. 6
Where do you get it?
For more information,
Colenutt Contracting Services Ltd.
Phone : (780)778-0550
E-mail : colecon@telus.net
Website: colenuttcontracting.com
Linkedin: Chris Colenutt
Facebook: Sentinel Polished Rod
protection System
Presently looking for a distributor in your area for
that one call convenience that allows you to receive
all your supplies from one supplier.
8. 7
To: Chris Colenutt
Re: Sentinel Polished Rod Protector
We have installed four systems to date and have seen great improvements on our run times.
Scored polished rods have been an issue in the past. Numerous attempts have been made to
correct the issue with limited success. Upon installation of the Sentinel Polished Rod Protector
system, the issues have been reduced.
I was personally on location when one of the systems was installed. The pump jack was aligned
and roller guides were installed. This reduced the scoring but it was still evident. As soon as the
system was installed the scoring disappeared. The installation on this particular well was
installed 8 months ago and there has been no issues since.
Currently our longest running system was installed 13 months ago. We have not seen any issues
since the installation.
Regards,
Glen Klein, P.Eng
Service Rig Coordinator, AB/BC
CELL 780.898.6760 | DIRECT 780.514.7061 | MAIN 780.514.7050 | FAX 780.542.2609