Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube. SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502. Heat shrink joints are also available to suit unarmoured cables (including 624Y twin and earth, RV-K flexible power cable, waveform aluminium cables) and paper insulated lead sheathed cables (PILC). LSF zero halogen heat shrink cable joints for BS6724 cables are also available. DNV accepted heat shrink ships cable joints are available for power, control, instrumentation, signal and communications cables. * No resin to mix or curing delays - no hazardous class jointing resins * Immediate energisation and backfill capability of heat shrink cable joint * Suitable for ducting, vertical and overhead cable jointing * Light, compact cable joints for space and weight savings on cable tray * Suitable for LV jointing of underground cables - submersible joints available

1. CABLE JOINTS, CABLE TERMINATIONS, CABLE GLANDS, CABLE CLEATS
FEEDER PILLARS, FUSE LINKS, ARC FLASH, CABLE ROLLERS, CUT-OUTS
11KV 33KV CABLE JOINTS & CABLE TERMINATIONS
FURSE EARTHING
www.cablejoints.co.uk
Thorne and Derrick UK
Tel 0044 191 490 1547 Fax 0044 191 477 5371
Tel 0044 117 977 4647 Fax 0044 117 9775582
Heatshrink Joints to suit Low Voltage
Cables type Xlpe/Swa/Pvc 0.6/3.3kV
¡ the jointing requirements of
Meets
BS 6910 part 1
¡
Unlimited shelf life
¡
Slim profile
¡ for immediate backfill
Allows
¡
No messy toxic resins involved
¡
Non armoured, lead sheathed and Zero
Halogen cable joints are also
available on request
¡
Independent test reports available
Shrink Polymer Systems type SPA heatshrink joint kits are intended for use with Pvc and xlpe cables for
voltages up to 3.3kV.
The system comprises of adhesive lined connector insulation tubes, Heavy duty armour cage (copper
mesh on the smallest joints), armour support rings, armour clamps and an outer thick wall adhesive lined
heatshrink tube.
The single core joints contain a heavy duty Aluminium cage if the cable has aluminium wire armours.
Many thousands of joints are installed worldwide including critical locations such as ministry of defence,
department of transport and subsea offshore sites.
HEATSHRINK JOINTS TO SUIT SINGLE CORE XLPE/AWA/PVC
PART
CABLE
VOLTAGE
NUMBER
RANGE
SPA 50-95-1
SPA 120-185-1
SPA 240-300-1
SPA 400-630-1
50-95mm2
0.6/3.3kV
2
0.6/3.3kV
2
0.6/3.3kV
2
0.6/3.3kV
120-185mm
240-300mm
400-630mm
HEATSHRINK JOINTS TO SUIT XLPE/SWA/PVC
PART
CABLE
VOLTAGE
NUMBER
RANGE
SPA 1.5-2.5SPA 4-6SPA 10-16SPA 25-50SPA 70-95SPA 120-185SPA 240-300-
1.5 - 2.5mm2
2
600/1000V
600/1000V
4 - 6mm
2
600/1000V
2
0.6/3.3kV
10 - 16mm
25 - 50mm
2
0.6/3.3kV
70 - 95mm
2
0.6/3.3kV
2
0.6/3.3kV
120 - 185mm
240 - 300mm
To denote number of cores, add number to end of
reference. Example: 12 core 2.5mm2 = SPA 1.5-2.5-12
Page 42