This document summarizes research conducted on the failure of an 8000-ton heavy duty press. The researchers created a 3D model of the upper tool part and conducted finite element analysis to determine the stresses and strains. They found that low cycle fatigue was the mechanism responsible for failure of the upper tool part. Recommendations were made to stiffen the upper tool part to extend its life by reducing stresses. Submodeling and Neuber's approximation method were used to better understand stress distributions and strains in the upper tool part. The analyses identified low cycle fatigue as the cause of failure and provided suggestions to strengthen the tool and prolong its useful life.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
An Experimental Investigation into the Grindability Aspects of Newly Develope...IDES Editor
Ceramics are getting widely used in many engineering applications. These ceramic materials need to be ground. Unfortunately, the ground ceramic components mostly contain surface/subsurface damages. To minimize the grinding induced damages selection of appropriate grinding process parameters is very important. Ceramic composite material (AlSiTi) has been selected in the present study to investigate its grindability. This research work deals with the analysis of the process parameters such as wheel speed, table feed and infeed as influential factors, on the force components, grinding specific energy and surface roughness values based
on Taguchi’s experimental design method. Scanning electron microscopy (SEM) has been used to analyze the subsurface damages. The result provides valuable insight into the grindability aspects of the composite ceramic (AlSiTi).
Vibrational Analysis Of Cracked Rod Having Circumferential Crack IDES Editor
The frequency ratio of torsional vibration of a rod without crack and of rod with crack subjected to torque at the free end for various crack depth and varying crack location is investigated. It is found that even a cracked of small depth is
dangerous at the fixed end, also as the crack depth is increases more than 50% of diameter of rod there is a considerable drop in natural frequency of the rod .
Study of Damage to ABS Specimens Submitted To Uniaxial Loadingtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
The International Journal of Engineering & Science would take much care in making your article published without much delay with your kind cooperation.
SLIDING WEAR OF AA6061/CARBON BLACK METAL MATRIX COMPOSITESIAEME Publication
In this study, the effects of carbon black amount on fracture and wear behaviors of AA6061-carbon black metal matrix composites produced by stir casting route were investigated. Wear tests were performed in a pin on type wear apparatus under different loads of 10, 20, 30 N with different sliding speeds of 2, 3 and 4 m/s, at three different sliding distances of 500, 750 and 1000 m. The design of experiments was carried out as per Taguchi technique. Wear rate function was determined in terms of volume fraction, normal load, sliding speed and sliding distance. It was found that there was a good agreement between the theoretical and the experimental value of wear rate. Maximum sliding wear of 68.72% was attributed sliding distance. Sliding wear resistance increases by 42.56% for AA6061/30%CB metal matrix composites as compared to the matrix alloy AA6061
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
An Experimental Investigation into the Grindability Aspects of Newly Develope...IDES Editor
Ceramics are getting widely used in many engineering applications. These ceramic materials need to be ground. Unfortunately, the ground ceramic components mostly contain surface/subsurface damages. To minimize the grinding induced damages selection of appropriate grinding process parameters is very important. Ceramic composite material (AlSiTi) has been selected in the present study to investigate its grindability. This research work deals with the analysis of the process parameters such as wheel speed, table feed and infeed as influential factors, on the force components, grinding specific energy and surface roughness values based
on Taguchi’s experimental design method. Scanning electron microscopy (SEM) has been used to analyze the subsurface damages. The result provides valuable insight into the grindability aspects of the composite ceramic (AlSiTi).
Vibrational Analysis Of Cracked Rod Having Circumferential Crack IDES Editor
The frequency ratio of torsional vibration of a rod without crack and of rod with crack subjected to torque at the free end for various crack depth and varying crack location is investigated. It is found that even a cracked of small depth is
dangerous at the fixed end, also as the crack depth is increases more than 50% of diameter of rod there is a considerable drop in natural frequency of the rod .
Study of Damage to ABS Specimens Submitted To Uniaxial Loadingtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
The International Journal of Engineering & Science would take much care in making your article published without much delay with your kind cooperation.
SLIDING WEAR OF AA6061/CARBON BLACK METAL MATRIX COMPOSITESIAEME Publication
In this study, the effects of carbon black amount on fracture and wear behaviors of AA6061-carbon black metal matrix composites produced by stir casting route were investigated. Wear tests were performed in a pin on type wear apparatus under different loads of 10, 20, 30 N with different sliding speeds of 2, 3 and 4 m/s, at three different sliding distances of 500, 750 and 1000 m. The design of experiments was carried out as per Taguchi technique. Wear rate function was determined in terms of volume fraction, normal load, sliding speed and sliding distance. It was found that there was a good agreement between the theoretical and the experimental value of wear rate. Maximum sliding wear of 68.72% was attributed sliding distance. Sliding wear resistance increases by 42.56% for AA6061/30%CB metal matrix composites as compared to the matrix alloy AA6061
Shear Field Size Effect on Determining the Shear Modulus of Glulam beam - Cri...CrimsonPublishersRDMS
Shear Field Size Effect on Determining the Shear Modulus of Glulam beam by Niaz Gharavi* in Crimson Publishers: Peer Reviewed Material Science Journals
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Implementation of 1D Brinson model in 3D SMA specimens Influenced by stress c...irjes
The application of small-size SMA components has grown rapidly in various industries over the last
few years. Due to their complex nature, local constitutive models for those components have proven somehow
impractical; whereas global models have been unable to take the stress concentration into consideration and
hence cannot predict the nucleation and stress patterns accurately, especially in small samples. Moreover, FE
analyses are impossible to conduct in cases where a large number of evaluations are required to design a suitable
SMA sample. This paper proposes a new iterative method to accurately calculate the stress and martensitic
volume fraction in samples with stress concentration using 1D Brinson model. The method is implemented in
the form of a computer code which is then refined iteratively using FEM model which is validated based on
experimental data. Final assessments show that the proposed method could predict the stress values accurately
at negligible computational costs.
Behaviour Analysis of Corroded Wires Based on Statistical ModelsIJERDJOURNAL
ABSTRACT: Steel wires are the primary components of a lifting wire rope. The behaviour of a wire governs the behaviour of the whole of the cable. The physico-chemical processes like rates of degradation due to the environment (corrosion, etc.) are different for each layer, external layers being more exposed. The analysis of steel wires behaviour is traditionally based on statistical models describing the variability of its properties. For this purpose a statistical study was carried out on two populations of healthy and corroded wires by applying the Student distribution to select the most reliable results and the Weibull distribution to define the survival probability and the failure probability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Prediction Models for Sliding Wear of AA3003/Al2O3 CompositesIJERA Editor
In the present work, the AA3003/Al2O3 metal matrix composites were manufactured at 10% and 30% volume
fractions of Al2O3. The composites were wear tested at different levels of normal load, sliding speed and sliding
distances. The microstructure of worn surfaces pertaining to AA3003/ Al2O3 composite reveals the fracture of
AA3033 alloy matrix as well as the detachment of Al2O3 particles from the matrix.
In a multi-storied building, the beam-column joint is one of the most critical regions. Usually the beam-column joint was considered as rigid frames. Various researchers over the past years indicated that the joint is not rigid. Now it is also stated that instead of the failure in beam and column, failure can also occur in joint hence joint must be considered as a structural member. The Indian standards define a joint as the portion of the column within the depth of the deepest beam that frames into the column. In framed structures the bending moment and shear forces are maximum at the junction area. So, beam column joint is one of the failure zones. Among the beam column joints, the exterior joint is more critical. The exterior beam column joint have been a study for about 30 years since now. Still there are many more to be understood. In the present work a building is designed in STAAD. Pro V8i and an exterior beam column joint is considered. This joint is modelled in NX CAD and imported to ANSYS to analyse it to derive the shear stress and the corresponding deformation. Pramod Verma | Prof. Pratiksha Malviya "Exterior Beam Column Joint: An Assessment" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-2 , February 2019, URL: https://www.ijtsrd.com/papers/ijtsrd21589.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/21589/exterior-beam-column-joint-an-assessment/pramod-verma
Optimisation of Welds with Manufacturing ConsiderationsSIMULIA
Fatigue is the main in-service failure mode for automotive chassis & suspension parts, especially weld fatigue. Over the years, Tata Steel Automotive Engineering (TSAE) has developed techniques for CAE durability assessment including the optimisation of seam-welded chassis/suspension structures. Seam weld optimisation at TSAE has previously been based on a constant weld length and constant gap between welds for each weld run. This method has two drawbacks; weld patterns generated are regular in nature, reducing the flexibility to position welds where they are most effective and• excessively short welds are often left at the end of a run of welds. The objective was to develop an improved optimisation technique using Isight that always produced a manufacturing feasible design and allowed more flexible and irregular positioning of welds. Manufacturing constraints considered were minimum weld length, minimum gap length and minimising the number of start/stop operations. To reduce the number of design variables, a new load-case-weighted optimisation scheme was developed using a single weighting factor for each load case. These factors were used to generate weld patterns by scaling the strain energy density in finite elements from an initial fully welded design. Weld elements were selected for retention/deletion by comparing a weighted sum across all load cases with a threshold value. During each optimisation, Isight varied the weighting factors as “design variables” to minimise overall weld length, while achieving stiffness and fatigue life targets. The process has been extended to function for laser weld designs where an intermittent weld pattern is generally the most effective.
Experimental And FE Analysis Of Eccentric Loaded Symmetrical And Unsymmetrica...IJERA Editor
This paper presents experimental and FE analysis of eccentric loaded bolted joint under symmetric and unsymmetrical bolt system with consider bolt pretension. A cad model of a bolted joint has been developed using modeling software PROE5.0 and FE analysis was carried out by using ANSYSWORKBENCH12.0.stress analysis has been carried out by varying bolt pattern of bolted joint for predict maximum heavily loaded bolt. Experimental work was conducted to measure maximum shear strength of the specimens for validation of the developed FE model. Experimental work was carried out on hydraulic jack and specimen of bolted joint was tested to know maximum shear strength of bolt. The results from both FE analysis and experimental work were then compared and show close results among them.
Experimental and Numerical Assessment of Crash Behavior of Welded Thin Wall R...IDES Editor
The crash behavior of Cold Rolled Mild Steel
(CRMS) closed form thin section produced by stitch welding
at periodic intervals of length was studied by conducting axial
compressive tests at loading velocities of 5 mm/min and 6000
mm/min. The deformation shape, peak forces and energy
absorption capacity of the sections estimated numerically
showed a good correlation with the experimental data.
Probabilistic Design Hollow of Airfoil Wing by Using Finite Element MethodIJERA Editor
This study represents simulation of Airfoil composite beam by using Monte Carlomethod. A three dimensional static analysis of large displacement type has been carried out. Finite element analysis of NACA0012 airfoil composite structure has been carried out and uncertainty in bending stress is analyzed. Bending stress was objective function. Chord length , beam length ,elastic modulus in XY,YZ,XZ,shear modulus of epoxy graphite in in XY,YZ,XZ, ply angle and ply thickness of airfoil section, force are varied within effective range and their effect on bending stress has been analyzed. In order to validate the results, one loop of simulation is benchmarked from results in literature. Ultimately, best set of probabilistic design variable is proposed to reduce bending stress under static loading condition.
Shear Field Size Effect on Determining the Shear Modulus of Glulam beam - Cri...CrimsonPublishersRDMS
Shear Field Size Effect on Determining the Shear Modulus of Glulam beam by Niaz Gharavi* in Crimson Publishers: Peer Reviewed Material Science Journals
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Implementation of 1D Brinson model in 3D SMA specimens Influenced by stress c...irjes
The application of small-size SMA components has grown rapidly in various industries over the last
few years. Due to their complex nature, local constitutive models for those components have proven somehow
impractical; whereas global models have been unable to take the stress concentration into consideration and
hence cannot predict the nucleation and stress patterns accurately, especially in small samples. Moreover, FE
analyses are impossible to conduct in cases where a large number of evaluations are required to design a suitable
SMA sample. This paper proposes a new iterative method to accurately calculate the stress and martensitic
volume fraction in samples with stress concentration using 1D Brinson model. The method is implemented in
the form of a computer code which is then refined iteratively using FEM model which is validated based on
experimental data. Final assessments show that the proposed method could predict the stress values accurately
at negligible computational costs.
Behaviour Analysis of Corroded Wires Based on Statistical ModelsIJERDJOURNAL
ABSTRACT: Steel wires are the primary components of a lifting wire rope. The behaviour of a wire governs the behaviour of the whole of the cable. The physico-chemical processes like rates of degradation due to the environment (corrosion, etc.) are different for each layer, external layers being more exposed. The analysis of steel wires behaviour is traditionally based on statistical models describing the variability of its properties. For this purpose a statistical study was carried out on two populations of healthy and corroded wires by applying the Student distribution to select the most reliable results and the Weibull distribution to define the survival probability and the failure probability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Prediction Models for Sliding Wear of AA3003/Al2O3 CompositesIJERA Editor
In the present work, the AA3003/Al2O3 metal matrix composites were manufactured at 10% and 30% volume
fractions of Al2O3. The composites were wear tested at different levels of normal load, sliding speed and sliding
distances. The microstructure of worn surfaces pertaining to AA3003/ Al2O3 composite reveals the fracture of
AA3033 alloy matrix as well as the detachment of Al2O3 particles from the matrix.
In a multi-storied building, the beam-column joint is one of the most critical regions. Usually the beam-column joint was considered as rigid frames. Various researchers over the past years indicated that the joint is not rigid. Now it is also stated that instead of the failure in beam and column, failure can also occur in joint hence joint must be considered as a structural member. The Indian standards define a joint as the portion of the column within the depth of the deepest beam that frames into the column. In framed structures the bending moment and shear forces are maximum at the junction area. So, beam column joint is one of the failure zones. Among the beam column joints, the exterior joint is more critical. The exterior beam column joint have been a study for about 30 years since now. Still there are many more to be understood. In the present work a building is designed in STAAD. Pro V8i and an exterior beam column joint is considered. This joint is modelled in NX CAD and imported to ANSYS to analyse it to derive the shear stress and the corresponding deformation. Pramod Verma | Prof. Pratiksha Malviya "Exterior Beam Column Joint: An Assessment" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-2 , February 2019, URL: https://www.ijtsrd.com/papers/ijtsrd21589.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/21589/exterior-beam-column-joint-an-assessment/pramod-verma
Optimisation of Welds with Manufacturing ConsiderationsSIMULIA
Fatigue is the main in-service failure mode for automotive chassis & suspension parts, especially weld fatigue. Over the years, Tata Steel Automotive Engineering (TSAE) has developed techniques for CAE durability assessment including the optimisation of seam-welded chassis/suspension structures. Seam weld optimisation at TSAE has previously been based on a constant weld length and constant gap between welds for each weld run. This method has two drawbacks; weld patterns generated are regular in nature, reducing the flexibility to position welds where they are most effective and• excessively short welds are often left at the end of a run of welds. The objective was to develop an improved optimisation technique using Isight that always produced a manufacturing feasible design and allowed more flexible and irregular positioning of welds. Manufacturing constraints considered were minimum weld length, minimum gap length and minimising the number of start/stop operations. To reduce the number of design variables, a new load-case-weighted optimisation scheme was developed using a single weighting factor for each load case. These factors were used to generate weld patterns by scaling the strain energy density in finite elements from an initial fully welded design. Weld elements were selected for retention/deletion by comparing a weighted sum across all load cases with a threshold value. During each optimisation, Isight varied the weighting factors as “design variables” to minimise overall weld length, while achieving stiffness and fatigue life targets. The process has been extended to function for laser weld designs where an intermittent weld pattern is generally the most effective.
Experimental And FE Analysis Of Eccentric Loaded Symmetrical And Unsymmetrica...IJERA Editor
This paper presents experimental and FE analysis of eccentric loaded bolted joint under symmetric and unsymmetrical bolt system with consider bolt pretension. A cad model of a bolted joint has been developed using modeling software PROE5.0 and FE analysis was carried out by using ANSYSWORKBENCH12.0.stress analysis has been carried out by varying bolt pattern of bolted joint for predict maximum heavily loaded bolt. Experimental work was conducted to measure maximum shear strength of the specimens for validation of the developed FE model. Experimental work was carried out on hydraulic jack and specimen of bolted joint was tested to know maximum shear strength of bolt. The results from both FE analysis and experimental work were then compared and show close results among them.
Experimental and Numerical Assessment of Crash Behavior of Welded Thin Wall R...IDES Editor
The crash behavior of Cold Rolled Mild Steel
(CRMS) closed form thin section produced by stitch welding
at periodic intervals of length was studied by conducting axial
compressive tests at loading velocities of 5 mm/min and 6000
mm/min. The deformation shape, peak forces and energy
absorption capacity of the sections estimated numerically
showed a good correlation with the experimental data.
Probabilistic Design Hollow of Airfoil Wing by Using Finite Element MethodIJERA Editor
This study represents simulation of Airfoil composite beam by using Monte Carlomethod. A three dimensional static analysis of large displacement type has been carried out. Finite element analysis of NACA0012 airfoil composite structure has been carried out and uncertainty in bending stress is analyzed. Bending stress was objective function. Chord length , beam length ,elastic modulus in XY,YZ,XZ,shear modulus of epoxy graphite in in XY,YZ,XZ, ply angle and ply thickness of airfoil section, force are varied within effective range and their effect on bending stress has been analyzed. In order to validate the results, one loop of simulation is benchmarked from results in literature. Ultimately, best set of probabilistic design variable is proposed to reduce bending stress under static loading condition.
Flexibility Analysis In Industrial Piping Through The Finite Elements And Pho...IJERA Editor
The industry needs predictability to work on a large scale without complications, only this way you can ensure your productivity. The piping flexibility analysis provides a prediction of future problems and proposes applicable solutions, with the objective of preventing pipes to suffer collapses, that can impact the production process and costs, and provide safety to workers and the environment, while avoid leaks and possible contamination. The aim of this study is analyse the flexibility of industrial piping through the finite elements and photoelasticity methods. For stresses analysis, using a computerized body of proof, it`s possible to find, through finite elements and photoelasticity`s practical project, the values of the stresses and the places where they are being applied. To guarantee that the computerized and practical models are consistent with reality, a mathematical model, already tested and proved, will also be implemented and compared to the others, so there are evidences that all models used are really reliable and can be used in large-scale industrial projects, with complex studies. A comparison of a mathematical model through balanced guided beam, a finite elements model using the software ANSYS® and a photoelasticity of a resin pipe will show that the method with better applicability in industries is the computational, showing trustable stress, reaction and deformation values as well as a detailed visualization of them distribution along the object of study.
Abstract The present research work is to determine buckling load per unit length in rectangular plate with circular cut-outs under bi-axial compression using 2D finite element analysis. The commercial finite element analysis software ANSYS has been successfully executed. The buckling factors are evaluated by changing the position of the holes, length to thickness ratio. The effect of changing the position of holes, a/b ratio, b/t ratio and buckling load per unit length is discussed. The results shows that buckling load per unit length is in clamped-clamped boundary conditions and buckling load is more at top positioned hole, decreases with increase in aspect ratio, decrease with increase breadth to thickness ratio. Keywords: Buckling analysis, Finite element method, Buckling load per unit length , carbon/epoxy composite plate, aspect ratio, b/t ratio, and Biaxial load.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Effect of lamination angle on maximum deflection of simply supported composit...RAVI KUMAR
In this project a composite laminated beam is studied with glass-epoxy and graphite-epoxy combination. The beam is composed of four layers of different combination of composite material (glass epoxy and graphite epoxy composite). The beam is simply supported at both the ends and is subjected to uniformly distributed load along the length. Transverse deflection is computed for different lamination angle (0^0-〖90〗^0) by using Euler- Bernoulli’s theory (or CLPT). Maximum transverse deflection analysis is carried out using derived analytical expressions. The research carried out in this project will enable to determine the beam strength due to bending loads. The importance of fibre reinforcement in the manufacturing of the beam is studied in terms of bending strength of the beam. MATLAB codes are generated to implement analytical expiations of the composite beam.
The main objective of the paper is to find out the lamination angle at which minimum deflection is obtained & to find out the effect of lamination angle on maximum transverse deflection of the beam.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Prediction of Fatigue Life of Boom Nose End Casting Using Linear Elastic Frac...IJERA Editor
The main objective of this study is to get the life estimation of Boom nose end casting using theoretical approach and compaired it with finite element method. Therefore, this study consists of three major sections : (1) dynamic load analysis (2) FEM and stress analysis (3) prediction of fatigue life for Boom nose end casting. In this study a dynamic loads were obtained from cyclic loading at different time. Finite element analysis was performed to obtain the variation of stress magnitude at the crack locations. This loads and boundary condition were applied to the FE model in ANSYS. The analysis was carried out for different crack length on the surface area of circle of Boom Nose End Casting. As a result, fatigue life for different crack length on the Boom Nose End Casting is obtained. The main objective of this study is to investigate the fatigue life of Boom Nose End Casting under complex loading conditions. Due to the repeated bending and tensile loading acting, Boom Nose End Casting fails, as cracks forms in surface area of circle. Hence, fatigue plays an important role in Boom Nose End Casting development. Accurate prediction of fatigue life is very important to insure safety of components and its reliability. The Linear Elastic Fracture Mechanics approach is used to predict the fatigue life of Boom Nose End Casting.
OPTIMIZATION AND FATIGUE ANALYSISOF A CRANE HOOK USING FINITE ELEMENT METHODijmech
Stress analysis plays an important role in the design of structures like crane hook under loading conditions.
Crane hook is a reliable lifting component being used in industries. Structure failure of crane hook occurs
because of the stress induced due to repetitive loading and unloading conditions. In this study, solid
modeling of crane hook having trapezoidal cross-section referring to one of its existing design is done
using SOLIDWORKS. Further, analyses are carried out in ANSYS Workbench and nCode DesignLife. The
lengths of two parallel sides of the cross-section of crane hook are varied and different candidates are
obtained for loading capacity of 30 ton on the basis of Mass, total Displacement and Von-Mises stress.This
is done to reduce weight and balance economy. Further, out of these candidates, best candidates are
considered and fatigue analysis is performed on these candidates.
Finite Element Analysis of Damping Performance of VEM Materials Using CLD Tec...IJERA Editor
Most engineering structures experiences vibrational motion, this unwanted vibrations can result in premature
structural failure. Many methods are developed which enhances capability of damping such as constrained layer
damping. Shear motion is produced in VEM due to constraining layer to resist unwanted vibrational energy.
This paper shows theeffect of varying the thickness of viscoelastic materials on damping performance of CLD
beam.The damping performance is measured in terms of modal loss factor.
Role of Simulation in Deep Drawn Cylindrical PartIJSRD
Simulation is widely used in forming industry due to its speed and lower cost and it has been proven to be effective in prediction of formability and spring back behavior. The purpose of finite element simulation in the sheet metal forming process is to minimize the time and cost in the design phase by predicting key outcomes such as the final shape of the part, the possibility of various defects and the flow of material. Such simulation is most useful and efficient when it is performed in the early stage of design by designers, rather than by analysis specialists after the detailed design is complete. The accuracy of such simulation depends on knowledge of material properties, boundary conditions and processing parameters. In the industry today, numerical sheet metal forming simulation is very important tool for reducing load time and improving part quality. In this paper finite element model for the deep-drawing of cylindrical cups is constructed and the simulation results are obtained by using different simulation parameters, i.e. punch velocity, coefficient of friction and blank holder force of the FE mesh-elements and these results are compared with experimental work.
IRJET-Finite Element Analysis of Glazed SurfaceIRJET Journal
Raghunath .D. Deshpande, Gayatri Chiniwal, Laxmi Golsangi, "Finite Element Analysis of Glazed Surface", International Research Journal of Engineering and Technology (IRJET), Vol2,issue-01 March 2015. e-ISSN:2395-0056, p-ISSN:2395-0072. www.irjet.net
Abstract
In the present work finite element analysis of a glazed surface of a structure is performed. Considering particular location, topography and terrain and considering glass panel of a particular type, size and thickness, analysis is performed for wind pressure and suction acting on the surface. Different cases are considered – (i) varying truss widths, (ii) varying cable position and (iii) varying number of cables. The results of this work show that displacement, stress and weight of the steel of structure vary linearly with the variation in truss width. Displacement is found to be least for a certain range of truss width. Stresses decrease with increase in truss width and the weight of steel increases with increase in truss width. Having known this, one can choose economical and efficient steel supporting structure to support the glazing.
A computational approach for evaluating helical compression springseSAT Journals
Abstract Helical compression springs are generally synthesized and evaluated by determining the maximum torsional stress, fatigue life, natural frequency, and/or load loss due to stress relaxation. To this end, researchers have developed finite element analysis (FEA) modeling methods to simulate the design performance of helical compression springs. The intent of this paper was to make a useful contribution to the published works for evaluating round wire helical compression springs. Specifically, commercially available FEA software was used to construct a structural model of a helical compression spring to simulate its full range of compression. The proposed FEA modeling methodology considers coil-to-coil contact and the end coils were modeled as rigid surfaces. With 9 mm of compression, the predicted spring rate correlated with the analytically calculated value to within 5%. Keywords: Helical compression spring, machine component design, spring FEA
A computational approach for evaluating helical compression springs
Gy3113381349
1. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
Design and Assessment of Low Cycle Fatigue Life of a Heavy
Duty Press
A.V.Pradeep*, Kona Ram Prasad**, CH.Jagadeesh***
* (Department of Mechanical Engineering , S.V.P.Engineering College, Visakhapatnam)
**(Department of Mechanical Engineering , S.V.P.Engineering College, Visakhapatnam)
***(Department of Mechanical Engineering , S.V.P.Engineering College, Visakhapatnam)
ABSTRACT
Our project involves investigations on 1.1 OBJECTIVE OF THE PROJECT
the failure of an 8000 ton heavy duty press. This The main objective of the project is to investigate the
press is used for forming boiler drums by U-shell failure and suggest remedial measures for extending
pressing operation. The failure of the press had the life of the press.
occurred due to formation of several cracks in
the upper tool part of the press. 1.2 WORK CARRIED OUT
Initially the detailed three dimensional The design of the upper tool part of the
model of the upper tool is developed using the press has been analyzed using FEA for the extreme
popular solid modeling package, Pro/E. Later load conditions to which the press is subjected. The
meshing of the model is done in Hypermesh and work comprises of preparing detailed three
analysis of the meshed model is carried out using dimensional models using solid modeling packages
the analysis package Ansys 8.0. The upper tool of like Pro/E and analysis of the existing design using
the press has been analysed using analysis package like Ansys along with meshing
After getting the stresses and strain packages like Hypermesh. The stress analysis
values in the upper tool body from the analysis, involves elasto-plastic analysis. The complexity of
the expected low cycle fatigue life of the press is the analysis required use of advanced concepts like
predicted using the Coffin-Manson’s relations. elasto-plastic analysis, Sub modeling, use of macros
These investigations have clearly brought out the etc. After the analysis, the expected life of the press
cause of the failure of the press. The upper tool is predicted.
part of the press has a finite life design as regards These investigations have clearly brought
cold correction operations, and, low cycle fatigue out the cause of the failure of the press. The upper
is the life consuming mechanism responsible for tool part of the press has a finite life design as
its failure. regards cold correction operations, and, low cycle
Further recommendations are made for fatigue is the life consuming mechanism responsible
extension of life of upper tool part of press by for its failure. Recommendations are made for the
way of stiffening. The scope of the work is extension of life of the upper tool part of press by
further enhanced by finding the real stress way of stiffening.
distribution and strains existing in the upper tool The suggested modifications strengthen the
by Neuber’s approximation method. Thereafter upper tool and thereby reduce the stresses resulting
the reliability of the method is discussed. in extension of life. This work involves many trials
of stiffening arrangements and their analyses to
1. INTRODUCTION work out the most suitable arrangement.
In the last three-four decades, with the The scope of the work is further enhanced
advent of computer based design packages of solid by carrying out basic studies on the application of
modeling and FEA, the field of mechanical design the method of Sub modeling in elasto-plastic
has undergone a sea change. These methods have analysis. Also studies are made in respect of
equally contributed in the failure analysis and life methods of computation of elasto-plastic strains
estimation of structures. Though commonly used, using Neuber‟s approximation method.
the real test of all these techniques lies in their
application to real life problem. This thesis presents 2.ELASTO-PLASTIC ANALYSIS AND
a real life problem of failure analysis of an 8000 T SUBMODELING
heavy duty Press. Detailed investigations are carried 2.1 Elasto-Plastic (Nonlinear) Analysis:
out to analyze the failure of press. Also design The elasto-plastic analysis is the analysis
modifications are suggested for its life extension. which takes into consideration the deformations of
the body unlike the elastic analysis, which assumes
that the body is perfectly elastic. The elastic analysis
is valid only in the situations where the stresses
induced in the body are below the yield value of the
1338 | P a g e
2. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
material. There is always a permanent deformation
when the yield value of the material is crossed.
In those situations performing the elasto-
plastic analysis becomes very much necessary. It
gives the exact values of the stresses and strains
taking into consideration the deformations. One of
the primary purposes of theory of plasticity is the
explanation of the deformational behaviour of the
materials stressed beyond the elastic limit. A second
purpose is to determine the stresses at which the
plastic behaviour initially begins.
The discussion of elasto-plastic analysis is
started taking the classical example of the
overhanging beam. Later it is extended to the press
problem. The geometry of the beam along with the Fig – 2.3: At load 250N
boundary conditions is as shown in figure 2.1
Fig – 2.1
The following attributes are specified in
Ansys for the present problem;
1. Element Type: Solid 42,i.e. Plane element with
two D.O.F
2. Material Properties:
Elastic Modulus; E = 169000 N/sq.mm Fig – 2.4: At load 300N
Poisson‟s Ratio = 0.3
Yield Stress = 310 MPa
Tangent Modulus = 8450
The value of tangent modulus is generally taken in
between E/20 and E/30. Here it is taken as E/20.
Load Force in Stress in X-
Step Newton direction (MPa)
1 200 243.589
2 250 304.486
3 300 328.922
4 350 316.681
5 200 192.488
6 0 78.155
The results for the six load steps are shown in
the figures 2.2 to 2.8. Fig – 2.5: At load 350N
Fig – 2.2: At load 200 N
Fig – 2.6: At load 200N
1339 | P a g e
3. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
To obtain more accurate results in such a region,
you have two options:
(a) Reanalyze the entire model with greater mesh
refinement, or
(b) Generate an independent, more finely meshed
model of only the region of interest and
analyze it. Obviously, option (a) can be time-
consuming and costly (depending on the size of
the overall model). Option (b) is the
Submodeling technique
Submodeling is also known as the cut-
boundary displacement method or the specified
boundary displacement method. The cut boundary is
the boundary of the submodel, which represents a
Fig – 2.7: At load 0N Residual stress cut through the coarse model. Displacements
calculated on the cut boundary of the coarse model
are specified as boundary conditions for the
submodelInitially the concept of Submodeling is
illustrated with the classical problem of a Plate with
a central hole (Later it will be extended to the main
problem of 8000T Press). The geometry is
symmetrical about X andY-axis
Fi
Fig – 2.8: At load 0N Residual strain
The yield stress of the material is given as
310 MPa. So in the third load step the yield value is Fig – 2.9
crossed and the elastoplastic method is used by the
software. Till the yield value is reached the elastic For the purpose of analysis only the upper
analysis only is performed. right quarter portion of the plate is considered which
Once the yield value is crossed the is as follows;
elastoplastic attributes are considered and the
analysis proceeds as the elastoplastic analysis taking
into consideration the permanent deformations.
It is also observed that the stresses for the
first load step and the fifth load step are different
even though the values of the forces are same i.e.
200N. This is because of the elastoplastic
considerations. Initially there is no deformation for
first load step. But for the fifth load step there is
some deformation and due to this stresses are
reduced. In the sixth load step even though there is
zero loading there is some stress remaining. This is
the residual stress in the beam.
Fig – 2.10
2.2 Concept of Submodeling
Submodeling is a finite element technique 2.3 Elasto-Plastic analysis and Submodeling for
used to get more accurate results in a region of the the plate with hole:
given model. Often in finite element analysis, the Initially the full geometry of the 2-D plate
finite element mesh may be too coarse to produce is created in Ansys 8.0, by creating keypoints, lines
satisfactory results in a region of interest, such as a and areas. The geometry is then meshed with coarse
stress concentration region in a stress analysis .The meshing. The element type selected is Solid 42, i.e
results away from this region, however, may be Plane element with two degrees of freedom. Meshed
adequate. model is shown in figure 2.11;
1340 | P a g e
4. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
The Von-Misses stress distribution in the plate for
all the five load steps are as follows;
Fig – 2.11
The following material properties are specified for
performing the Elasto-plastic analysis;
a. Elastic modulus = 169000 MPa
b. Poisson‟s Ratio = 0.3
c. Yield Stress = 310 MPa
d. Tangent Modulus = 8450
As the concept of Elasto-Plastic analysis is
previously discussed the presentation directly
proceeds with the present problem of concern.
Due to symmetry of the geometry only the
quarter portion of the plate is considered for the
analysis purpose. As the upper right quarter of the
plate is considered, the following constraints should Fig – 2.12 to 2.16 Von-Misses stress distribution
be applied on the plate; in the plate for the five load steps
a. Constraints of symmetry on the left vertical
face CHAPTER 3
b. Constraints in Y-direction on the bottom face STRESS ANALYSIS OF UPPER TOOL OF
The geometry, mesh and the displacement THE PRESS
boundary conditions are ready for our analysis 3.1 INTRODUCTION:
purpose. Now apply a negative pressure (i.e. In this chapter the stress analysis concepts
tensile pressure) on the top face of the plate and see which were discussed in the preceding chapters, like
the stressdistribution. Elasto-Plastic Analysis, Submodeling etc are
Because it is Elasto-Plastic analysis the applied to the upper tool of the press to find the
pressure is not applied in a single load step. Pressure actual stress distribution in the component.
is applied in five load steps with the following
values;25MPa, 50 MPa, 75 MPa, 100 MPa, 125 3.2 SOLID MODEL OF THE UPPER TOOL:
MPa. The three dimensional solid model of the
upper tool of the 8000 T press is modeled using the
part modeling module of Pro/Engineer. Before
modeling it must be ensured that the units are set to
the required system. The units followed here are
“mm” for length and “Newton” for force. The solid
model of the central four limbs of the upper tool on
which the total loading of 8000T is applied during
cold working is shown in figure 3.1;
1341 | P a g e
5. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
Fig – 3.1Solid Model Of The Upper Tool
It is evident from the above shown figure
that there is symmetry in the geometry. So for the FIG -3.3 : Geometry along with mesh
purpose of analyzing the upper tool all the four After meshing is successfully done, the
limbs need not be considered. The symmetry is three dimensional brick elements are organised into
exploited as illustrated in Fig. 3.2; a new collector and all other collectors containing
the geometric entities and shell elements are deleted.
The elements in the new collector are specified with
an element type Solid 45, which is of first order
type. Now the elements are exported to Ansys via
data file.
3.4 IMPORTING THE MODEL INTO ANSYS
AND PERFORMING ELASTIC ANALYSIS:
The „.dat‟ file created in Hypermesh is
imported into Ansys and the nodes and elements are
available for analysis as shown in figure 3.4;
Fig – 3.2
Fig – 3.2 : The symmetry is exploited
The quarter model is considered for
analysis purpose and here after only the quarter
model is dealt with. The boundary conditions are
selected based on the quarter part. FIG - 3.4 : Nodes and elements are available for
analysis
3.3 MESHING OF THE UPPER TOOL: Now the boundary conditions and loads
The geometry of the upper tool is first can be applied to the component. The following
imported into Hypermesh from Pro/E. Hypermesh degrees of freedom constraints are applied on the
has the ability to read Pro/E files directly. F.E.model;
Also the “iges” file can be created in Pro/E Constraints in X-direction on the Z face
and then read in Hypermesh. IGES stands for Initial nodes to account for the symmetry.
Graphics Exchange Specification. Constraints in Y-direction on the top face
The geometry is then meshed with eight nodes to fix the upper tool.
noded brick element by performing mapped Constraints in Z-direction on the X face
meshing. The geometry along with mesh looks as nodes to account for the symmetry.
shown in fig.3.3; A pressure of 90.61 N/sq.mm is applied on
the bottom face of the tool. The pressure applied is
90.61 N/sq.mm because it is the equivalent value of
pressure to the force of 500T acting on the quarter
model.
The pressure is 90.61 N/sq.mm because;
Total load on four limbs = 8000T
Load per limb = 2000T
Load per half limb = 1000T
Load per quarter limb = 500T = 500000kg =
4905000 N
1342 | P a g e
6. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
Equivalent Pressure = Load / Bottom area
= 4905000/54164.2
= 90.61 N/mm ²
After the loads and boundary conditions are applied
the F.E.model looks as follows;
Fig – 3.8: Stresses at the critical regions on which
concentration must be.
The submodel is selected and it looks as follows
along with the mesh;
Fig – 3.5: F.E.model of the tool
The problem is completely defined and
ready to be solved. So the problem is solved to
obtain the solution. The results are shown below in
fig. 3.6 and 3.7;
Fig – 3.9: Submodel of the selected region with
the mesh.
Now the nodes on the top, bottom and right
side face are selected and a node file is written. The
FIG – 3.6 : Stress in Y- Direction window is closed and the previous problem with
unconverged solution is opened. This is used as the
coarse model for interpolating the boundary
conditions. Here the node file is read and the load
file is written. Again the submodel is opened and the
load file is read. The interpolated boundary
conditions are applied to the submodel in the form
of degrees of freedom constraints. The submodel
along with the boundary conditions is as shown in
figure 8.10;
Fig –3.7: Von – misses stress
Performing a single analysis may not be
sufficient to present the converged results in F.E.M.
This can be said by looking at the percentage
difference between the values of SMN and SMNB
in the „Stress in Y-direction plot‟ and SMX and
SMXB in the „Von-Misses Stress plot‟. It is
customary that the percentage difference is not
allowed to be more than about 10%. But here the
difference is around 20%. So it is needed to refine FIG – 3.10 : Submodel along with the boundary
the mesh and resolve the problem. It is unnecessary conditions
to solve the problem with the total geometry. So the Now, giving the same material properties
concept of Submodeling is followed to solve for the this problem is solved to obtain the results. The
stresses at the critical regions. There are three results are shown in the figures 8.11 and 8.12.
regions on which concentration must be paid. They
are shown in figure 3.8;
1343 | P a g e
7. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
FIG – 3.11 : Stress in Y- Direction
Fig – 3.15: Von – misses stress
It is clearly evident from the results (fig. 3.14 and
8.15) that the solution is converged. This is because
the percentage difference between SMN & SMNB
in „Stress in Y-direction‟ plot and SMX & SMXB in
„Von-Misses Stress‟ plot is around 10%.
Also to cross check the convergence of the
solution the submodel is again remeshed with finer
elements and the problem is solved. It is observed
Fig – 3.12: Von – misses stress that the results are more or less the same as the
above results.
Even this solution seems not converged
because the percentage difference between SMN So the final results for the elastic solution of upper
and SMNB in „Stress in Y-direction‟ plot and SMX tool of the press are tabulated below:
and SMXB in „Von-Misses plot‟ is about 16%. So Stress in Y-direction Von-Misses Stress
again the mesh is refined and the problem is
- 448.961 MPa 454.519 MPa
resolved. The submodel along with new refined
mesh and the results are shown in the following
page. The same procedure followed previously is to 3.5 ELASTOPLASTIC ANALYSIS
be followed to obtain the solution. PERFORMED ON THE UPPER TOOL OF
THE 8000T PRESS
First the quarter portion of the upper tool is
considered as done in elastic analysis previously and
it is meshed with eight noded coarse brick elements
in Hypermesh. Then the data file is created in
hypermesh and that file is read into Ansys. So the
elements and nodes are ready for analysis. Now the
elastoplastic analysis is carried out on the upper tool
Fig – 3.13 Submodel along with new refined mesh with the necessary boundary conditions and the
loads. Later the results are noted.
Fig – 3.14 : Stress in Y- Direction
FIG - 3.16: The coarse model meshed in
Hypermesh
1344 | P a g e
8. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
1. Now a pressure of 50 MPa is applied at the
bottom surface as the first load step.
2. Later three more load steps are applied as
follows;
3. Now the four load steps are solved to obtain the
results. The results are as follows;
As this meshing is coarse the solution
cannot be considered as the converged solution. So
it is tried to refine the mesh and solve the problem
again and again till the converged solution is Fig - 3.18: Submodel in hyper mesh
obtained. Unfortunately as the mesh is refined
continuously the size of the problem goes on 5. Now select the nodes on the top, bottom and
increasing tremendously to such an extent that the right face of the submodel as shown in figure
computer cannot solve the problem. 8.19;
So the size of the problem needs to be
reduced and at the same time a fine mesh is needed
to get a converged solution. Now at this juncture the
classic method of Submodeling is followed to
reduce the size of the problem so that the computer
can solve the problem without demanding for much
memory space.
The problem is to be solved using both the FIG – 3.19: Nodes of the submodel
concepts of Elasto-plastic analysis and
Submodeling. 6. Now write the nodes file with the following
command in Ansys;
3.6 Elasto-Plastic Analysis and Submodeling nwrite, submodel, nod
Applied to the Upper Tool Here ‘submodel’ is the name and ‘nod’ is the
As Submodeling is described and extension for the node file.
illustrated with an example previously, directly the 7. Close the window and open the coarse full
list of the step by step approach for performing model, which is solved and has some
Submodeling along with Elasto-plastic analysis is preliminary solution.
provided. 8. Here it must be ensured that the solution is in
Steps: the first load step. To ensure this, read the
1. First it must be ensured that the Elasto-plastic results of the first load step through GUI (or)
solution for the full geometry (quarter section) use the following command;
with coarse meshing is available. This solution lsread, 1
is any how ready in the previous section 8.5. 9. Later the following procedure must be
2. Suitable submodel must be selected so that all followed,
the critical regions are available in it. General Postprocessor > Submodeling > Interpolate
3. Now the submodel is meshed with finer mesh D.O.F
(8 noded brick elements) than the full model Now a window appears as follows;
using Hypermesh and later the nodes and
elements are transferred into Ansys. Same mesh
size is maintained as in the case of elastic
Submodeling done previously.
4. At this stage the submodel is ready in Ansys
and is as shown in figure 3.17;
Here the node file is provided as input and the
loads at the top and bottom surfaces of the submodel
are interpolated from the full model. All the loads
are interpolated as degree of freedom constraints
and the load file for the first load step is written with
the name ‘submodel1.lod’.
10. Thereafter steps 8 and 9 are repeated for all the
remaining load steps and the following load
files are written;
FIG – .3.17: Submodel in ansys submodel2.lod,submodel3.lod, submodel4.lod
1345 | P a g e
9. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
11. Now the full model with coarse mesh is closed under the action of the external forces is assumed to
and again the submodel is opened. Suitable be known. The method can be conveniently
material properties are provided and then the explained with the help of the following figure 8.20;
following steps are followed, The elasto-plastic solution can be found out
The following command is given; from the Neuber‟s curve by looking at the point
*use, submodel1.lod where it cuts the Stress-Strain curve. The Neuber‟s
Then the loads interpolated from the first hyperbola must be constructed such that it travels
load step in the full model are applied in the form of from the elastic solution curve to the stress-strain
degrees of freedom constraints on the submodel. (hardening) curve.
Now write this loading situation as the first load
step.
Now read the remaining load files as
follows subsequently writing the second, third and
fourth load steps after each load file is read;
12. Now solve all the four load steps to get the
solution. Here the submodel with the loading
situation interpolated from the full coarse model
is being solved.
13. The results obtained with the submodel will Fig – 3.20 Stress-strain (hardening) curve
tally with those results obtained if the full
model is solved with the same mesh size as that After getting the Strain and Stress values
of the submodel. This was experimentally they are plotted with suitable scale on the same
showed previously taking the example of plate graph on which the Ramberg-Osgood stress-strain
with hole. curve is plotted. The point where both the curves
14. The results of the submodel i.e. the upper tool meet gives the elasto-plastic solution. In our present
of the press are as follows; case;
Load Pressure Stress in Y- Von- Neuber's Conversion
Step Applied direction Misses 500
No: Stress 400
1 50 -247.743 250.811
2 75 -325.887 318.323 300
Stress-Strain Curve By Ramberg-
Stress
Osgood Method
Neuber's Curve
3 90.61 -347.741 319.541 200
4 125 -378.494 337.558 100
With a pressure of 90.61 N/sq.mm the
0
stresses are as shown above in bold. Also the values 0 0.25 0.5 0.75 1
% Strain
1.25 1.5 1.75 2
of stresses and total strain are tabulated below; From the above graph in figure 3.21 the
following results can be drawn;
Pressure Stress in Von Total
Applied Y- Misses Strain Equivalent Total 0.35 %
direction Stress Strain
90.61 MPa -347.741 319.541 0.002851 Elastic Strain 0.18 %
MPa MPa Plastic Strain 0.17 %
Real (elasto-plastic) 320 MPa
3.7 NEUBER’S APPROXIMATION METHOD Stress
TO FIND ELASTO PLASTIC SOLUTION:
Neuber‟s rule is used to convert an These results are nearer to the results
elastically computed stress or stain into the real obtained in the Elasto-Plastic analysis. The results
stress or strain when plastic deformation occurs. The do not match exactly because this is an
Neuber‟s method of finding the elasto-plastic approximation method and also does not take into
solution is a formula based mathematical approach consideration the geometry and the loading
by which one can find the elasto-plastic solution
conditions of the problem. The method evaluates the
without performing the elasto-plastic analysis. solution based on the value of the elastic stress.It is
This is an approximation technique that can evident from the five stress distributions that the
be used to take into account the redistribution of maximum stress is always prevailing at the same
stress caused by plastic flow in a zone of stress point due to stress concentration. The values of the
concentration, a case often met in practice. The maximum stress for the five load steps are tabulated
conditions of validity of this method are that the below;
plastic zone must remain sufficiently contained
(surrounded by elastic zone) and that the loading
must be radial. The elastic solution of the problem
1346 | P a g e
10. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
Coarse Mesh Results Max Tensile Max Compressive Von-Misses
Pressure Von- Stress(MPa) Stress(MPa) Stress(MPa)
Load Step Applied On Misses 44.298 - 448.961 454.519
Number the Top Face Stress
Now the following modifications are made to the
(MPa) (MPa)
design to reduce the max compressive stress value
1 25 101.309
to less than 250MPa. The stress value is tried to be
2 50 202.618 kept below 250MPa taking into consideration the
3 75 303.927 low cycle fatigue, to which the component is
4 100 312.524 subjected to.
5 125 318.255 4.2 FIRST VERSION OF DESIGN
properties are assigned same as the coarse model to ENHANCEMENT
the submodel also. 1. Half Part with Middle Cut Rib:
Let the file name for the submodel be assigned as In this model one rib of 50mm thickness
submodel.db and 150mm height is provided in the half symmetry
The submodel‟s geometry is created in Ansys 8.0 portion and the other rib remains the same as in the
and it is meshed with fine elements. The geometry original model. The middle rib is cut at the top
along with the mesh is shown in the figure 3.22. portion to provide provision for holes. The figure
and the results are shown;
Fig –4.2: Half part with middle cut rib
Max
Max Tensile Von-Misses
Compressive
Stress(MPa) Stress(MPa)
Fig – 3.22 Stress(MPa)
85.678 -381.377 359.449
Now, from this submodel the nodes on the
top face are selected and written to a node file with
the following name and extension; 2. Part with Back Plate:
In this model a back plate of 25mm
thickness is provided to the body. The stresses are as
In the second version of design enhancement, the shown in the table;
main objective is to reduce the thickness of the plate welded to
the body of the upper tool, in the successful model of the first
version of design because the plate thickness is 50mm and
welding such a big plate with 50mm thickness practically
poses many problems during and even after welding.
So initially the following geometry is tried out;
CHAPTER 4
MODIFICATION IN DESIGN OF THE Fig – 4.3 Part with back plate
UPPER TOOL
4.1 Introduction: 3. Outer Plate With Middle Rib:
Before discussing about the modifications This model consists of an outer plate of
done to the existing design a glance at the existing 50mm thickness and a center rib of 50mm thickness
model of the press is required. The stress values (25mm due to quarter symmetry) and 150mm
observed in the analysis are also tabulated below; height. The stresses are as tabulated below;
Fig – 4.4: Outer Plate With Middle Rib
Fig – 4.1: First normal solid model
1347 | P a g e
11. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
CHAPTER 5 appreciable because of the plate thickness being
DISCUSSION OF RESULTS 50mm. It is not a good practice to weld structures of
After the accomplishment of the detailed such high thickness and thus weight. This makes the
stress analysis and life calculations the following welding weak.
results were arrived at: Therefore the design is modified once again in the
The maximum stress values in the upper second version as follows;
tool of the press observed in the Elastic Analysis a. A plate of 32mm is welded to the body of the
along with Submodeling are as follows; upper tool.
STRESS IN Y- VON-MISSES b. Two ribs of 50mm thickness are provided on
DIRECTION STRESS the plate.
- 448.961 MPa 454.519 MPa c. A rib of 25mm thickness is provided in
between the two ribs of 50mm thickness.
The above values are far more than the
The stress values in the second version of design
yield value of the upper tool material which is enhancement are as follows;
310MPa and hence the Elasto-plastic analysis is
carried out along with Submodeling to find the
actual values of stresses and strains. CHAPTER 6
The actual stress values observed in the Elasto- CONCLUSIONS
Plastic Analysis are as follows; After successfully completing the project
Now the Elasto-plastic solution is found the following conclusions can be made in
out using the Neuber‟s method. As mentioned accordance to the work done;
earlier this method aims at finding the Elasto-plastic Rigorous Elasto-Plastic Analysis is carried
solution without actually performing it, rather the out on the heavy duty press to predict the life.
solution is arrived at based on empirical relations Submodeling is equally valid for Elasto-Plastic
taking the elastic stress as the input. The Elasto- analysis as it is for the elastic problems. This is
plastic solution found out by this method produces proved in the dissertation by taking the example of
the following results; the plate with hole.
The Stress-Strain curve developed using
Neuber’s Elasto- Neuber’s Elasto-plastic the Ramberg-Osgood relations satisfactorily
plastic stress strain matches with the original Stress-Strain curve of the
material. Neuber‟s Conversion Method to calculate
320 MPa 0.35 the stresses and strains for elasto-plastic problems
gives reasonably good results.
By comparing the above results with the The Coffin-Mansion‟s relations provide a
results obtained in Elasto-plastic analysis it can be method satisfactorily to predict the life of
said that the Neuber‟s method gave a satisfactory engineering components. The finite life of the press
result. But it does not give exact results because the has been consumed in twenty years due to the
method does not take into consideration the excessive operations involving high loads.
geometry and the loading conditions of the problem. Modification is done to the design of the
The only thing it considers is the value of the Elastic upper tool to ensure that it can withstand the loading
Stress. Also, this method is applicable only if the conditions. The modified design can satisfactorily
plastic stress is contained between elastic stresses. withstand the loading conditions.
Based on the values of stresses and strains
in the Elasto-plastic analysis the life of the press is
CHAPTER 7
estimated to be 22000 cycles using the Coffin-
Manson‟s relations. RECOMMENDATIONS FOR FUTURE
By seeing the values of the stresses one can WORK
say that the existing design needs to be strengthened No work in the universe has a final solution
by providing modifications to the design. The or conclusion. So it will be hypocritical to say, the
following modifications are suggested to be project work is complete. There is always
provided in the upper tool as shown in Fig.-- refinement to solutions in any calculations,
a. A plate of 50mm is welded to the body of the especially in engineering calculations. There is lot
upper tool. of scope for work to be carried out in the case of the
b. Two ribs of 50mm thickness are provided on press even though lot of work has been done. A lot
the plate. of research work can be done in the following areas;
The suggested modifications bring down 1. Even though the optimum geometry is proposed
the stress values considerably, which help in the Optimization of the geometry can be carried
extending the life of tool. The stress values in the out using the available Finite Element
modified design of upper tool are as follows. Packages.
The stress values are observed to be 2. The Optimization of the weight can also be
satisfactory but the design is not practically carried out using the Finite Element packages.
1348 | P a g e
12. A.V.Pradeep, Kona Ram Prasad, CH.Jagadeesh / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 3, Issue 1, January -February 2013, pp.1338-1349
3. The Life Calculation is done in the present
work using the Coffin-Manson relations. This
can be cross checked by performing the Life
Calculation using the popular Finite Element
Packages. Also the life can be calculated for the
modified design.
REFERENCES
1. Low Cycle Fatigue and Life Prediction:
Amzallag, Leis and Rabbe Publisher
A.S.T.M International.
2. Journal of Applied Mechanics and
Technical Physics C/C of Zhurnal
Prikladnoi Mekhaniki I Tekhnicheskoi
Fiziki 28
3. Journal of Strain Analysis For Engineering
Design
4. Transactions - American Society of
Mechanical Engineers Journal of
Engineering Materials and Technology
5. Materials Science and Engineering
(Lausanne)
6. Transactions - American Society of
Mechanical Engineers Journal of
Engineering Materials and Technology
7. International Journal of Pressure Vessels
and Piping
8. Fatigue and Fracture of Engineering
Materials and Structures
1349 | P a g e