This document is a curriculum vitae for Hazem Mahmoud Abdelaziz, a mechanical engineer with over 9 years of experience in welding, non-destructive testing, and in-service inspection of equipment like pressure vessels, heat exchangers, and pipelines. He is certified in inspection standards like API 510, API 653, and ASNT Level II. He has worked as a senior inspection engineer conducting inspections and evaluating equipment integrity at Egyptian Natural Gas Co.

1. CURRICULUM VITAE
HAZEM MAHMOUD ABDELAZIZ
MECHANICAL ENGINEER
( 9 ) years' experience
PERSONAL DETAILS
Residential Address : 202-elyassmin (8)-fifth Settlement-New Cairo–Cairo-Egypt.
Mobile: +201114538781 / +201227918930
Date of Birth: 22- February- 1985
Nationality: Egyptian
E-mail: hazem_abdelaziz@yahoo.com
Military status / passport: exempted / passport no. ( A17067264 )
Martial state: married + (2) children
summary
I have more than 9 years of experience in the field of Welding, NDT and In-service
Inspection of plant static equipment's including pressure vessels, columns, drums, heat
exchangers, boilers, coolers, safety relief valves, plant process piping networks, pipelines
and aboveground storage tanks in oil and gas industry.
Certified API 653 Aboveground Storage Tank Inspector, API 510 Pressure Vessel Inspector,
API 570 Piping Inspector and ASNT Level II – VT, RT, UT, MT & PT.
EDUCATION HISTORY
may 2007 B.Sc. of Mechanical engineering ( Power section ) –
shoupra Faculty of engineering – banha University
June 2011 Post graduate Diploma of pipe lines & turbines & pumps – Faculty
of engineering – Cairo University
TRAINING & CERTIFICATIONS
2013 API 570 INSPECTOR certificate no. (51040)
2014 API 510 INSPECTOR certificate no. (53270)
2015 API 653 INSPECTOR certificate no. (63016)
2010 ASNT II (R.T. , U.T. , M.T. , P.T. , and V.T. )
2011 ASME B (31.8) , ( VIII )
2009 AUTOCAD (I)

2. 2015 cathodic protection principles
2016 PMP preparation course
WORK EXPERIENCE
Period : From 17/03/2008 to Present Egyptian Natural Gas Co. (GASCO)
Job Title: senior inspection engineer / plant inspector
Job details :
 Conduct off-stream and on-stream inspection on the plant stationary
equipment including pressure vessels, heat exchangers, drums, tanks, top
side structures, PRD’s and piping systems according to Company established
policies and procedures and issues inspection reports Perform in-service
pipeline inspection
 Planning, supervision and coordination of all on-stream and shutdown
inspection/NDT activities of plant static equipment's including pressure
vessels, separators, desalters, dehydrators, heat exchangers, coolers,
columns, heaters, PSVs, piping, pipelines, aboveground storage tanks, etc.
 Implement the computerized inspection program through Validation of the
asset registry, equipment details and the inspection results.
 Conduct fitness for service assessment for the different equipment, set the
scope of corrective action, set and implement the quality control scope and
testing.
 Coordinates with the Operations , Planning and Maintenance supervisors such
activities as the scheduling and planning of inspections, obtaining the
required permits and performing any required special audits of equipment.
 Upon failures of equipment such as pumps and vessels, inspect material and
assist in the preliminary failure assessments; prepare report and issue
recommendations, where applicable, via supervisor for action by relevant
departments.
 Review and analysis of previous inspection reports to summarize the integrity
status of the plant equipment's, piping systems and pipelines.
 Carrying out initial, detailed and final internal visual inspection complemented
with NDT examination for the static equipment's including pressure vessels,
separators, dehydrator, heat exchangers, coolers, columns, heaters and
tanks etc
 Preparation of inspection reports/certificates with all findings, abnormalities
and recommendations.
 Assist and participate in RBI analysis and developing the inspection
plans/frequencies for static equipment's, piping and pipelines.
 Witnessing of pressure relief valves calibration and testing
 Carrying out Inspection & thickness measurement for all platforms piping.
 Retirement thickness calculation, corrosion rate calculation, remaining service
life calculation for process piping systems and advising for any
repairs/replacement/re-rating requirements.

3.  Carrying out Inspection, Calibration & Testing for all relieve devices (RVs &
PSVs).
 Identifying areas of special concern and deterioration (e.g., dead legs,
injection points, corrosion under insulation (CUI), erosion &
corrosion/erosion), preparation of inspection procedures to follow-up their
resolution to improve Plant integrity.
 Review and comment of inspection test plan (ITP) .
 perform online inspection of pipeline with MFL PIGGING (INTELLIGENT
PIGGING) .
 Verify the Result of Inspection on the Gas Pipeline ( Distance & Clock ) with
GPS.
 Studying of inspection reports and FFP reports and making the repair plan of
the defects.
 Repair the pipelines defects with complete welding sleeve or half sleeve or
clock spring or wrapping.
 Construction site manager of Beni suiaf / dahshor pipeline ( 36" –
130 km )
 Mechanical fabrication supervision of gas pipeline stations ( filter – heater –
pressure reduction – metering ).
 perform pipeline shutdown – pipeline developing – pipeline route change ( by
open cut – Boring – HDD ).
 Review and approve of WPS , PQR , WQR , PWHT.
 Review and approve of NDT procedures.
 Evaluate and approve results of NDT procedures.
 Review/Approve hydrostatic test package for pipelines & pressure vessels.
 Pre-commissioning & Commissioning and Start-up for Gas pipelines including
cleaning and Drying of pipeline with Pi-directional pig , foam pigs and Purging
pipelines with nitrogen and gas-in for pipelines (2500 KM of pipelines ).
 perform hot tap of pipelines ( 0.5" to 24" ) for GASCO and other companies (
Nat gas – Petropel – Town gas ).
 Prepare and issue of technical specifications for Pre-commissioning &
Commissioning and Start-up for new pipelines .
 Review and comment and approval of sub-contractor documents and
submittals.
 Familiar with in-service inspection and construction codes/RPs such
as API (1104 , 570 , 577 , 571 , 578 , 574 , 510 , 572 , 576 , 653 , 650
, 651 , 652 , 575 , 580 ), ASME ( 31.8 , 31.3 , IX , V , VIII , 16.5A )
 Technical Member of HAZOP Team to study the following:-
1. Abo Homos / Elnubaria 24"Natural Gas Pipeline 65 km.
2. Elnubaria / Metnama 32" Natural Gas Pipeline 105 km.
Duties:
 Inspects plant stationary equipment by entering into vessels, boilers and
towers, during shutdowns, to check condition of equipment. Includes noting
observations on cracks, pits, thinning and any other pattern of erosion,
corrosion and other interior failure. Makes interpretations of findings,
analyses for failure, prepares report and issues recommendation. .

4. Supervision and coordination of all on-stream and shutdown inspection/NDT
activities of plant static equipment's including pressure vessels, separators,
desalters, dehydrators, heat exchangers, coolers, columns, heaters,
PSVs,piping, pipelines, tanks, etc - arranging loops for inspection according
design & operation parameters.
 Identifying areas of special concern and deterioration (e.g., dead legs,
injection points, buried piping, corrosion under insulation (CUI), erosion &
corrosion / erosion), preparation of inspection procedures to follow-up their
resolution to improve Plant integrity.
 Attend several shutdowns "turnarounds" & conducting internal inspection by
entering into vessels, spheres, heater and towers, to check condition of
equipment. Includes noting observations on cracks, pits, thinning and any
other pattern of erosion, corrosion and other interior failure.
 Carrying out visual inspection, internal, external & on-stream inspections on
Vessel, tanks, Columns, Towers, Heaters & Piping to determine if a weldment
or equipment meets the acceptance criteria in accordance with API 570 ,
API 510 , API 653.
 Preparation of inspection reports/certificates with all findings, abnormalities
and recommendations.
 Risk based integrity according to API 580.
 Damage mechanism according to API 571
 Familiar with RBI analysis and developing the inspection plans/frequencies for
plant equipment's, piping, pipelines & tanks
 In-service pipeline & plant inspection
-Calculating the corrosion rate ( LONG C.R. –SHORT C.R. )Inspection
intervals, the remaining life, the maximum allowable working pressure in
accordance with API 570 & API 510 & API 653.
 Complete isometric Drawings for piping systems using P&IDs.
 Identifying Damage Mechanisms and Failure Modes with corrosion specialist
 Determination TMLs according to API Recommended practice and corrosion
studies
 Review Materials certificates.
 Review PQR & WPS.
 Review the drawing
 Visual Inspection of the welding.
 Non Destructive Testing for Joints (MT, PT, RT & UT)
 Inspection of heat treatment.
 making punch and outstanding lists.
 Choosing TML and profile radiography points.
Period : From 10/01/2007 to 01/03/2008 Quality Control Company
Job Title: QC engineer
Job details :
 Review and comment inspection test plan (ITP).
 Review and comment NDT procedures.
 Demonstration of NDT procedures.

5.  Review and comment NDT results.
 Inspection of oil tanks , pressure vessels , steel structure building , piping
,towers and columns.
Duties:
 Review Materials certificates.
 Review PQR.
 Review WPS.
 Review the drawing.
 Inspection of Fit up.
 Supervising of Welding Process.
 Inspection of Tightening.
 Dimensional Inspection.
 Visual Inspection of the welding.
 Non Destructive Testing for Joints (MT, PT, RT & UT).
 Inspection of heat treatment.
 Inspection of Hydro Test.
 Inspection of sand blasting.
 Inspection of Painting.
OTHER SKILLS
Computer Skills:
 Microsoft XP applications (Word, Excel, Office, PowerPoint, Outlook, Access) , AutoCAD ,
primavera.
Language Skills:
English : fluent ( Speaking & Writing & listening )
Arabic : native language
French : beginner
Other:
 International driving license
PERSONAL COMPETENCIES
 Able to work under pressure and sincere in assignments.
 Adapt quickly and easily the concept/quality of work.
 Able to interact and co-ordinate at various levels.
 Good communication skills and have patience with problem solving abilities.
 Good team player/leader.
REFRENCES
Available upon request.