Dhruv Patel is an experienced electrical design engineer seeking a position to enhance product development through innovative solutions. He has a strong background in project execution, technical design, and team management, notably with companies like Modtech Machine Pvt. Ltd. and Electrotherm India Ltd., focusing on electrical systems and automation. He holds a bachelor's degree in Electrical & Electronics Engineering and has certifications in various engineering and management disciplines.

1. DHRUV PATEL
PROFILE • ABOUT ME
Seeking the position of an Electrical Design Engineer in a developing organization where
my skills, Experience, and knowledge of updating design techniques would boost the
development of products. I take part dedicatedly to raise efficiency, productivity, and
profitability of organization through the development and execution of innovative, cost-
effective solutions for products.
WORK EXPERIENCE
Modtech machine Pvt. Ltd, Ahmedabad, Gujarat
Sr. Design Engineer July 2021
 Lead team of engineer and draftsman for project/order execution.
 Selection of switch gear; load calculations; Cables; Control supply power backup
design; Body and control earth design in Panel; LV Motors selection; Cooling and
Lighting design for electrical panel to meet functional specifications with relevant
standards.
 Prepare SAP-ERP bill of material for projects.
 Prepare & review detail costing of equipment to comply budget for design.
Electrotherm India Ltd, Ahmedabad, Gujarat Apr-2019 to
July-2021
Sr. Design Engineer
 Guide team for project execution.
 Represent department to management committee for ISO 9001:2015 QMS.
 Consult with Vendors for selection of component and Discussion with engineers,
customers to improve existing or potential engineering projects or products.
 Verifying Troubleshooting and Maintenance Manual.
 Draw up field failure report which can provide instant guide to service team to ease
troubleshoot while solving critical breakdown.
 Study and analyze customer complain report, plan actions for product improvement
as well to start new product development.
 PLC-ladder logic & HMI Screen design preparation and check.
Electrotherm India Ltd, Ahmedabad, Gujarat Oct-2014 to
Apr-2019
Electrical Design Engineer
 Compose technical details such as Single line diagram, Electrical Load calculation for
inquiry order, wiring drawing and harness (Cable routing) specifications of electrical
systems, or topographical maps to ensure that installation and operations as per
standard norms and customer requirements.
 Selection of electrical equipment, components, and systems as like Switchgear;
Cables; Supply transformers.
 Prepare SAP-ERP bill of material for projects.
 Construct report of operational details and related documentation by testing with
various instruments such as Oscilloscope, Rogowski and harmonic analyzer.
EDUCATION
Electrical & Electronics, Bachelor of Engineering Completed
June 2014
[CGPA] 9.24 out of 10
GUJARAT TECHNOLOGICAL UNIVERSITY, Ahmedabad, Gujarat
PROJECTS
Project – 1: Implementation of Industrial Internet of things (IIoT) in Induction system
(Power supply and Mechanics)
Project type: List out objectives, ways to complete them to implement IIoT. Wherever
possible check with small scale hardware such as Raspberry Pi, Arduino
UNO R3.
Team Size: 2 (Self + team)
Role: I am selected by HOD and management to improve product with current
technology which can cover entire operation.
Ahmedabad, Gujarat, India
+91.9664891697,
“ +91.9687085646
dhruvpatel72835@gmail.com
http://www.linkedin.com/in/
‘ dhruvpatel1993
SKILLS
Auto-CAD
E-Plan
Matlab
Power Sim
PC-Schematic
GX-Developer
(PLC)
GT-Designer
(HMI)
MS Office suite
CERTIFICATIONS
 Scilab, Indian Institute of
technology Bombay – 2013
 Six Sigma White Belt, Aveta
business Institute– 2016
 LaTex, Indian Institute of
technology Bombay – 2014
 Lean Management, 7QC
Tools, Value stream
mapping , Electrotherm
Learning & Development team

2. Project – 2: Develop 50Ton Wax injection machine (CE Mark Equipment), UK
Project type: Design Wax injection machine electrical based on B&R PLC and HMI.
Team Size: 3 (Ele. Eng. + Mech. Eng. + draftsman)
Role: I was responsible to design power circuit as well as control circuit of
Electrical panel. Preparation of wiring harness, SLD, selection of VFD
mixer and motor starter switchgears for hydraulics. Selection of sensors
such as curtain sensors, proximity, level sensors etc.
Other: Confer with vendors to propose requirement of material with current CE
standard (Low voltage directive). Prepare full technical construction file
for the same.
More than 3 such system supplied by company after successful testing of
this equipment.
Project – 3: Design of end of line robotics solutions for pidilite.
Project type: Design case packer, case erector, and case mover with kuka robotics.
Team Size: 6 (Ele. Eng. + 3-Mech. Eng. + 2-draftsman)
Role: My task for this project is to overview electrical/automation part; such as
preparing SLD, select LV/MV switchgear, cables and motors with VFD.
Design specifications for VCB, ACB, PCC, MCC, and VFD Panels. Prepare
logic to handle equipment. Select sensors for line.
Other: Total 6 different line, out of it 1st line is successfully tested.
Project – 4: Fusion Bonded Epoxy coating line for steel bar. (Re-Bar coating)
Project type: Provide consultancy for greenfield line setup with in-house design,
manufacturing and erection-commissioning support.)
Team Size: 5 (Ele. Eng. + 2-Mech. Eng. + 2-draftsman)
Role: My task for this project is to overview electrical/automation part; such as
preparing SLD, select LV/MV switchgear, cables and motors with VFD.
Design specifications for VCB, ACB, PCC, MCC, and VFD Panels. Prepare
ladder logic for controlling movement of bar and interlocking PLC with line
equipment such as Induction heater, Shot blasting equipment, coating
equipment. Designed 750kW, 3kHz IGBT based induction heater power
supply unit for project.
Other: After successful commissioning of project, company supplied 3 such fully
functional line.
Project – 5: Continuous aluminum cast bar heater for cable production using
Induction (CSA / Ul mark equipment), CANADA
Project type: Design power supply unit for heating equipment to increase temperature
of aluminum cast bar from 410ᵒC to 525ᵒC for annealing. (Line final
product is Aluminum LV-MV cable)
Team Size: 3 (Ele. Eng. + Mech. Eng. + draftsman)
Role: Designed converter panel using IGBT. Developed control circuit with soft
start logic for 450kW whose output frequency is 1kHz. Also, selected
various switchgears for panel and motor control center of water
circulation system.
Other: Confer with vendors to propose requirement of material with current CSA
/ Ul standard.
Declaration
I, DHRUV PATEL, hereby declare that the information contained herein is true and correct
to the best of my knowledge and belief.
Ahmedabad ___________________
Soft Skill
Leadership quality
Problem Solving
Decision Making
Languages
English
Hindi
Gujarati
Personal Information
Birthday
26/08/1993
Gender
Male
Marital status
Married
Father’s Name
Mr.Dahyabhai Bhikhabhai Patel
Nationality
Indian
Engineering H/W
 Raspberry Pi - General
Purpose development board
 Arduino Uno R3 - General
Purpose development board
ISO 9001-2015 (INTERNAL
AUDITOR)
Best Kaizen Awards –
Electrotherm India (2018; 2019)