CS Unitec Reciprocating Air Saws are compact, quiet, and reliable. Models are ideal for cutting pipe, metals, fiberglass, timber, light-gauge metal & fiberboard. Portable reciprocating saws are also available for hand-held or clamp-on cutting in tough environments.
CS Unitec offers Pneumatic, Electric and Hydraulic models and a wide range of options for portable cutting of pipe, structural steel, tanks and other materials.
This document provides information about the P1 portable magnetic drill. It can drill holes up to 1-3/8 inches in diameter using annular cutters or twist drills. The drill features a 10 amp motor, weighs 26.5 pounds, and has a 4 inch stroke length. It comes equipped with safety features and accessories like a carrying case, lubrication pump, and safety strap. Optional accessories allow it to function as a standard drill press as well.
CS Unitec offers pneumatic and hydraulic models of chain saws. They are ideal for use in polyethylene plants, petrochemical industries, utilities, underground mines and marine applications.
CS Unitec Drill and Drive Units Catalog PagesCS Unitec
CS Unitec's catalog pages for quality industrial power tools including drill and drive units, tube rolling motors, tube expanding motors, electri drills and drive units, and drill motors and power drivers.
CS Unitec Portable Magnetic Drills: AIRBOR AB-4300CS Unitec
This document summarizes the specifications of the AIRBORTM AB-4300 portable magnetic drill. It has three main features:
1) It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments.
2) It has a fail-safe permanent magnet that is activated and deactivated by air pressure, and will not disengage if air flow is lost.
3) It can drill holes up to 2-1/16 inches in diameter and has a powerful 1.6 HP pneumatic motor and long drill stroke of up to 10-1/4 inches.
The document is describing the AIRBORTM AB-4300 portable magnetic drill. [1] It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments. [2] It has a 1.6 HP pneumatic motor, can drill up to 2-1/16" diameters, and has a long drill stroke of up to 10-1/4". [3] It is approved for use in hazardous atmospheres by ATEX and features automatic lubrication to reduce sparking.
CS Unitec offers Pneumatic, Electric and Hydraulic models and a wide range of options for portable cutting of pipe, structural steel, tanks and other materials.
This document provides information about the P1 portable magnetic drill. It can drill holes up to 1-3/8 inches in diameter using annular cutters or twist drills. The drill features a 10 amp motor, weighs 26.5 pounds, and has a 4 inch stroke length. It comes equipped with safety features and accessories like a carrying case, lubrication pump, and safety strap. Optional accessories allow it to function as a standard drill press as well.
CS Unitec offers pneumatic and hydraulic models of chain saws. They are ideal for use in polyethylene plants, petrochemical industries, utilities, underground mines and marine applications.
CS Unitec Drill and Drive Units Catalog PagesCS Unitec
CS Unitec's catalog pages for quality industrial power tools including drill and drive units, tube rolling motors, tube expanding motors, electri drills and drive units, and drill motors and power drivers.
CS Unitec Portable Magnetic Drills: AIRBOR AB-4300CS Unitec
This document summarizes the specifications of the AIRBORTM AB-4300 portable magnetic drill. It has three main features:
1) It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments.
2) It has a fail-safe permanent magnet that is activated and deactivated by air pressure, and will not disengage if air flow is lost.
3) It can drill holes up to 2-1/16 inches in diameter and has a powerful 1.6 HP pneumatic motor and long drill stroke of up to 10-1/4 inches.
The document is describing the AIRBORTM AB-4300 portable magnetic drill. [1] It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments. [2] It has a 1.6 HP pneumatic motor, can drill up to 2-1/16" diameters, and has a long drill stroke of up to 10-1/4". [3] It is approved for use in hazardous atmospheres by ATEX and features automatic lubrication to reduce sparking.
This hydro-test report summarizes the pressure testing of a 4" diameter and 158m long gas pipeline. Key details include:
- Water will be used to fill, flush, and pressure test the pipeline at 147 bar, which is 150% of the design pressure of 98 bar.
- Calculations are provided to determine the volume of water needed, expected back pressures, and pump requirements. Factors like elevation changes, pipe dimensions, and friction losses are accounted for.
- Test equipment will be calibrated and certified. Instruments will monitor and record pressure and temperature during the test.
- The pipeline will be isolated and prepared, then filled and pressure tested. Any leaks will be repaired before re-
The document provides instructions for hydrostatic testing circulating fluidized bed units. It outlines procedures for filling the unit with treated water, performing the hydrostatic test at 1.5 times the design pressure, and post-test procedures like pressurizing the unit with nitrogen and removing test plugs from safety valves. The key requirements are to fill the superheater and boiler with treated water, test to at least 1.5 times the design pressure, and pressurize the unit with nitrogen after testing.
The document provides information about pressure relief devices and safety valve testing procedures. It discusses what pressure relief devices are, common types like safety valves and pressure relief valves, and their key characteristics such as set pressure, overpressure tolerance, and blowdown percentage. It also outlines safety valve testing procedures like verifying the set pressure, repeatability testing, seat tightness testing, shell testing, and bellows integrity testing. Specifications for testing tolerances on set pressure at different temperature ranges are also presented.
Safety is the most important factor in designing a process system. Some undesired conditions might happen leading to damage in a system. Control systems might be installed to prevent such conditions, but a second safety device is also needed. One kind of safety device which is commonly used in the processing industry is the relief valve. A relief valve is a type of valve to control or limit the pressure in a system by allowing the pressurised fluid to flow out from the system.
Shaikh Nooruddin Yaqubali has over 12 years of experience as a piping supervisor for oil and gas projects. He has worked on numerous projects in the UAE and Saudi Arabia, managing fabrication, erection, welding, and quality control activities. He is knowledgeable in codes and standards like ASME and experienced in tasks like preparing test packs and as-built drawings.
When fluid flows through pipes, there are two types of losses - minor and major losses. Major losses are due to friction along the pipe walls and are quantified using the Darcy-Weisbach equation. The Darcy friction coefficient f depends on both the Reynolds number Re and the relative roughness κ/D. Plotting log f versus log Re for different pipes allows identification of the three sub-regions of turbulent flow - smooth, rough, and transitional - and how f varies in each sub-region.
This document discusses laminar and turbulent flow in pipes. It defines the critical Reynolds number that distinguishes between the two flow regimes. For non-circular pipes, it introduces the hydraulic diameter to characterize the pipe geometry. The document then covers topics such as the developing flow region, fully developed flow profiles and pressure drop, the friction factor, minor losses, pipe networks, and pump selection.
This document provides an overview of piping fundamentals for fresher engineers. It discusses what a piping system is, components like pipes, fittings, valves, supports and insulation. It also covers piping layout, modeling software, stress analysis, sizing calculations considering flow rates, pressures and material selection based on fluid properties. Critical high pressure and temperature piping in power plants requires special design considerations for material selection and allowing for expansion.
This document provides information on the design of pressure vessels. It defines pressure vessels as containers designed to operate above 15 Psi and discusses why proper design is important to prevent failure. The document outlines various codes used for pressure vessel design and stresses that vessels experience from internal pressure, weight, and other loads. It also describes common pressure vessel components like shells, heads, nozzles, and supports, and provides formulas for calculating thicknesses of different vessel components.
Piping Training course-How to be an Expert in Pipe & Fittings for Oil & Gas c...Varun Patel
Course Description
Piping a must know skill to work in Oil & Gas and similar Process Industries.
Oil and Gas industry is become a very competitive in the current time. Getting right mentor and right exposer within industry is difficult. With limited training budget spent by company on employee training, it is difficult to acquire the knowledge to success.
Knowing cross-functional skill give you an edge over others in your career success.
This course design based on years of field experience to ensure student will comprehend technical details easily and enjoy overall journey.
Learn in detail every aspect of Pipe & Pipe Fittings used in process industry
•Different types of Pipe, Pipe fittings (Elbow, Tee, reducers, Caps etc.), Flanges, Gaskets, Branch Connection, Bolting materials
•Materials (Metal-Carbon Steel, Stainless Steel, Alloy Steel etc. Non-Metal- PVC/VCM, HDPE, GRE-GRP etc.)
•Manufacturing methods
•Heat treatment requirements
•Inspection and Testing requirements (Non Destructive Testing, Mechanical & Chemical testing)
•Dimensions & Markings requirements
•Code & Standard used in piping
Content and Overview
With 2 hours of content including 30 lectures & 8 Quizzes, this course cover every aspect of Pipe, Pipe fittings, flanges, gaskets, branch connections and bolting material used in Process Piping.
This Course is divided in three parts.
1st part of the course covers fundamental of process industries. In this Part, you will learn about fundamental process piping. You will also learn about Code, Standard & Specification used in process industries.
2nd part cover various types of material used in process industries. In this part, you will learn about Metallic and Non-Metallic material used to manufacture pipe and other piping components.
3rd parts covers in detail about pipe and piping components used in Process piping. In this part we will learn about Industry terminology of Piping components, types of industrial material grade used in manufacturing and entire manufacturing process of these components. You will learn about different manufacturing methods, Heat treatment requirements, Destructive and Non-destructive testing, Visual & Dimensional inspection and Product marking requirements.
Upon completion, you will be able to use this knowledge direct on your Job and you can easily answer any interview question on pipe & fittings.
TRUMPF continues being a specialist in the metal processing industry for many years. They have combined their experience with the newest technology in their battery-powered cordless tools to help professionals get their work done with perfect results. Their new 18 V battery-powered tools are a perfect addition to their 10.8 V model line and offer the best solution for any need. The 18 V tools feature a robust gear head and brushless motors for longer run times, as well as Li-Ion batteries protected from overheating.
The document provides information about TRUMPF power tools for roofing and facade work. It describes several cutting and shearing tools, including slitting shears that can cut materials up to 2.5mm thick. It also details nibblers that can cut a variety of metal materials and profiles. Technical specifications are provided for each tool, including maximum material thickness, battery life, weight and included accessories. Contact information is given for TRUMPF locations in Switzerland and the UK.
CS Unitec's lubricants are ideal for cutting steel, stainless steel and hard metals. Your cutting tools will work cooler, longer and more efficiently. Available in liquid, solid and paste.
The document describes three new nibblers - the TruTool N 200, PN 200, and PN 201 - from TRUMPF that can be used on the same machine base. The nibblers are lightweight, easy to maneuver, and can cut sheet metal up to 2mm thick at speeds up to 2.2 meters per minute. Tools and cutting directions can be changed quickly without additional tools.
TRUMPF is a manufacturer of machine tools, laser technology, and electronics. They are certified to ISO 9001 quality standards. This document provides an overview of TRUMPF's electric and cordless power tools for various industries such as sheet metal fabrication, automotive, construction, and more. Key tools discussed include slitting shears, nibblers, profile nibblers, and a panel cutter for cutting sheet metal, ducts, and sandwich panels.
Sales7(at)tobeepump.com
Tobee® SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Design Features:
√ Less wear, less corrosion
Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
• Abrasion resistant A05 Ultrachrome® alloy.
• Abrasion/corrosion-resistant A49 Hyperchrome® alloy.
• Corrosion-resistant stainless steels.
• Natural and synthetic elastomers.
√ No submerged bearing failures
The robust cantilever shaft avoids the need for lower submerged bearings - which are often the source of premature bearing failure.
• Heavy duty roller bearings, above mountingplate.
• No submerged bearings.
• Labyrinth/flinger bearing protection.
• Rigid, large diameter shaft.
√ No shaft sealing problems
The vertical cantilever design requires no shaft seal.
√ No priming required
The top and bottom inlet design is ideally suited for “snore” conditions.
√ Less risk of blocking
The screened inlets and large impeller passages reduce the risk of blockages.
√ Zero ancillary water costs
The vertical cantilever design with no gland or submerged bearings avoids the need for expensive gland or bearing flushing water.
Tobee® SP/SPR Vertical Slurry Pumps Applications:
The SP/SPR verical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts.
The document discusses various types of toolholders including steep tapers, flanges, HSK, and shrink fit connections. It describes the characteristics of common toolholder types like CAT, BT, DIN, and ISO. It also covers topics like toolholder identification, balancing, accuracy, and best practices for maintaining toolholder accuracy.
Specifications of lapping, honing and broaching machineKaran Prajapati
This slide is prepared with the collective effort of Karan Prajapati, Athar Kothawal, Yudhishthir Ramnani and Samiraj Anupam who are doing B.Tech in Mechanical Engineering at School of Technology, Pandit Deendayal Petroleum University. The presentation describes the main terms of specifications in lapping, honing and broaching machines and also explaining the respective manufacturing processes. These machines are used for super-finishing processes.
(www.gbtechindia.com) We offer a large variety of office automation office automation system that are exclusively engineered to work efficiently in their specific applications. Our manufactured office automation system are cost effective and stylish in design. Our wide product range includes laminating machines, office binding machines, shredding machine and paper cutter.
This hydro-test report summarizes the pressure testing of a 4" diameter and 158m long gas pipeline. Key details include:
- Water will be used to fill, flush, and pressure test the pipeline at 147 bar, which is 150% of the design pressure of 98 bar.
- Calculations are provided to determine the volume of water needed, expected back pressures, and pump requirements. Factors like elevation changes, pipe dimensions, and friction losses are accounted for.
- Test equipment will be calibrated and certified. Instruments will monitor and record pressure and temperature during the test.
- The pipeline will be isolated and prepared, then filled and pressure tested. Any leaks will be repaired before re-
The document provides instructions for hydrostatic testing circulating fluidized bed units. It outlines procedures for filling the unit with treated water, performing the hydrostatic test at 1.5 times the design pressure, and post-test procedures like pressurizing the unit with nitrogen and removing test plugs from safety valves. The key requirements are to fill the superheater and boiler with treated water, test to at least 1.5 times the design pressure, and pressurize the unit with nitrogen after testing.
The document provides information about pressure relief devices and safety valve testing procedures. It discusses what pressure relief devices are, common types like safety valves and pressure relief valves, and their key characteristics such as set pressure, overpressure tolerance, and blowdown percentage. It also outlines safety valve testing procedures like verifying the set pressure, repeatability testing, seat tightness testing, shell testing, and bellows integrity testing. Specifications for testing tolerances on set pressure at different temperature ranges are also presented.
Safety is the most important factor in designing a process system. Some undesired conditions might happen leading to damage in a system. Control systems might be installed to prevent such conditions, but a second safety device is also needed. One kind of safety device which is commonly used in the processing industry is the relief valve. A relief valve is a type of valve to control or limit the pressure in a system by allowing the pressurised fluid to flow out from the system.
Shaikh Nooruddin Yaqubali has over 12 years of experience as a piping supervisor for oil and gas projects. He has worked on numerous projects in the UAE and Saudi Arabia, managing fabrication, erection, welding, and quality control activities. He is knowledgeable in codes and standards like ASME and experienced in tasks like preparing test packs and as-built drawings.
When fluid flows through pipes, there are two types of losses - minor and major losses. Major losses are due to friction along the pipe walls and are quantified using the Darcy-Weisbach equation. The Darcy friction coefficient f depends on both the Reynolds number Re and the relative roughness κ/D. Plotting log f versus log Re for different pipes allows identification of the three sub-regions of turbulent flow - smooth, rough, and transitional - and how f varies in each sub-region.
This document discusses laminar and turbulent flow in pipes. It defines the critical Reynolds number that distinguishes between the two flow regimes. For non-circular pipes, it introduces the hydraulic diameter to characterize the pipe geometry. The document then covers topics such as the developing flow region, fully developed flow profiles and pressure drop, the friction factor, minor losses, pipe networks, and pump selection.
This document provides an overview of piping fundamentals for fresher engineers. It discusses what a piping system is, components like pipes, fittings, valves, supports and insulation. It also covers piping layout, modeling software, stress analysis, sizing calculations considering flow rates, pressures and material selection based on fluid properties. Critical high pressure and temperature piping in power plants requires special design considerations for material selection and allowing for expansion.
This document provides information on the design of pressure vessels. It defines pressure vessels as containers designed to operate above 15 Psi and discusses why proper design is important to prevent failure. The document outlines various codes used for pressure vessel design and stresses that vessels experience from internal pressure, weight, and other loads. It also describes common pressure vessel components like shells, heads, nozzles, and supports, and provides formulas for calculating thicknesses of different vessel components.
Piping Training course-How to be an Expert in Pipe & Fittings for Oil & Gas c...Varun Patel
Course Description
Piping a must know skill to work in Oil & Gas and similar Process Industries.
Oil and Gas industry is become a very competitive in the current time. Getting right mentor and right exposer within industry is difficult. With limited training budget spent by company on employee training, it is difficult to acquire the knowledge to success.
Knowing cross-functional skill give you an edge over others in your career success.
This course design based on years of field experience to ensure student will comprehend technical details easily and enjoy overall journey.
Learn in detail every aspect of Pipe & Pipe Fittings used in process industry
•Different types of Pipe, Pipe fittings (Elbow, Tee, reducers, Caps etc.), Flanges, Gaskets, Branch Connection, Bolting materials
•Materials (Metal-Carbon Steel, Stainless Steel, Alloy Steel etc. Non-Metal- PVC/VCM, HDPE, GRE-GRP etc.)
•Manufacturing methods
•Heat treatment requirements
•Inspection and Testing requirements (Non Destructive Testing, Mechanical & Chemical testing)
•Dimensions & Markings requirements
•Code & Standard used in piping
Content and Overview
With 2 hours of content including 30 lectures & 8 Quizzes, this course cover every aspect of Pipe, Pipe fittings, flanges, gaskets, branch connections and bolting material used in Process Piping.
This Course is divided in three parts.
1st part of the course covers fundamental of process industries. In this Part, you will learn about fundamental process piping. You will also learn about Code, Standard & Specification used in process industries.
2nd part cover various types of material used in process industries. In this part, you will learn about Metallic and Non-Metallic material used to manufacture pipe and other piping components.
3rd parts covers in detail about pipe and piping components used in Process piping. In this part we will learn about Industry terminology of Piping components, types of industrial material grade used in manufacturing and entire manufacturing process of these components. You will learn about different manufacturing methods, Heat treatment requirements, Destructive and Non-destructive testing, Visual & Dimensional inspection and Product marking requirements.
Upon completion, you will be able to use this knowledge direct on your Job and you can easily answer any interview question on pipe & fittings.
TRUMPF continues being a specialist in the metal processing industry for many years. They have combined their experience with the newest technology in their battery-powered cordless tools to help professionals get their work done with perfect results. Their new 18 V battery-powered tools are a perfect addition to their 10.8 V model line and offer the best solution for any need. The 18 V tools feature a robust gear head and brushless motors for longer run times, as well as Li-Ion batteries protected from overheating.
The document provides information about TRUMPF power tools for roofing and facade work. It describes several cutting and shearing tools, including slitting shears that can cut materials up to 2.5mm thick. It also details nibblers that can cut a variety of metal materials and profiles. Technical specifications are provided for each tool, including maximum material thickness, battery life, weight and included accessories. Contact information is given for TRUMPF locations in Switzerland and the UK.
CS Unitec's lubricants are ideal for cutting steel, stainless steel and hard metals. Your cutting tools will work cooler, longer and more efficiently. Available in liquid, solid and paste.
The document describes three new nibblers - the TruTool N 200, PN 200, and PN 201 - from TRUMPF that can be used on the same machine base. The nibblers are lightweight, easy to maneuver, and can cut sheet metal up to 2mm thick at speeds up to 2.2 meters per minute. Tools and cutting directions can be changed quickly without additional tools.
TRUMPF is a manufacturer of machine tools, laser technology, and electronics. They are certified to ISO 9001 quality standards. This document provides an overview of TRUMPF's electric and cordless power tools for various industries such as sheet metal fabrication, automotive, construction, and more. Key tools discussed include slitting shears, nibblers, profile nibblers, and a panel cutter for cutting sheet metal, ducts, and sandwich panels.
Sales7(at)tobeepump.com
Tobee® SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Design Features:
√ Less wear, less corrosion
Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
• Abrasion resistant A05 Ultrachrome® alloy.
• Abrasion/corrosion-resistant A49 Hyperchrome® alloy.
• Corrosion-resistant stainless steels.
• Natural and synthetic elastomers.
√ No submerged bearing failures
The robust cantilever shaft avoids the need for lower submerged bearings - which are often the source of premature bearing failure.
• Heavy duty roller bearings, above mountingplate.
• No submerged bearings.
• Labyrinth/flinger bearing protection.
• Rigid, large diameter shaft.
√ No shaft sealing problems
The vertical cantilever design requires no shaft seal.
√ No priming required
The top and bottom inlet design is ideally suited for “snore” conditions.
√ Less risk of blocking
The screened inlets and large impeller passages reduce the risk of blockages.
√ Zero ancillary water costs
The vertical cantilever design with no gland or submerged bearings avoids the need for expensive gland or bearing flushing water.
Tobee® SP/SPR Vertical Slurry Pumps Applications:
The SP/SPR verical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts.
The document discusses various types of toolholders including steep tapers, flanges, HSK, and shrink fit connections. It describes the characteristics of common toolholder types like CAT, BT, DIN, and ISO. It also covers topics like toolholder identification, balancing, accuracy, and best practices for maintaining toolholder accuracy.
Specifications of lapping, honing and broaching machineKaran Prajapati
This slide is prepared with the collective effort of Karan Prajapati, Athar Kothawal, Yudhishthir Ramnani and Samiraj Anupam who are doing B.Tech in Mechanical Engineering at School of Technology, Pandit Deendayal Petroleum University. The presentation describes the main terms of specifications in lapping, honing and broaching machines and also explaining the respective manufacturing processes. These machines are used for super-finishing processes.
(www.gbtechindia.com) We offer a large variety of office automation office automation system that are exclusively engineered to work efficiently in their specific applications. Our manufactured office automation system are cost effective and stylish in design. Our wide product range includes laminating machines, office binding machines, shredding machine and paper cutter.
Growth in industrial technology is increasing demand for new equipment like rebar processing machines. The document discusses various types of equipment used for cutting, bending, and tying rebar, including electric cutters that can cut rebar up to 16mm, heavy duty cutters that can cut rebar up to 42mm, wire rope cutters that can cut steel rope from 1.5mm to 20mm, and automatic bending machines that can bend rebar up to 32mm. It also discusses manual and automatic rebar tying machines. The equipment allows for high production volumes in minimal time with minimal waste and flexibility.
This document provides information on hydraulic breakers and demolition tools from Atlas Copco, including:
- Descriptions of small (SB), medium (MB), heavy (HB), and bulk pulverizer (BP) series of hydraulic breakers with specifications for each model.
- Features of Atlas Copco's breakers like noise damping systems, lubrication systems, dust protection, and impact control systems.
- Information on compatible tools for different materials like concrete, asphalt, and rock.
- Specifications for combi cutters (CC) and demolition pulverizers (DP) that can be used for demolition, reduction, and recycling.
As a technique, crimping can produce long-lasting joints, efficiently and easily with very little training. Nowadays, Crimping has taken the place of soldering in many electrical applications and now is the most extensively used way for connections. When crimped properly, the strands remain individual even upon entering the insulation crimp, making the chances of strands breaking low,which ensure mechanically stability and corrosion-resistance. The proper crimping requires the contact, corresponding wire, and the most essential part--a suitable crimping tool.
IWISS with its sub-brand iCrimp offers crimping tools for virtually all types of electrical connections in the market, non-insulated, insulated, battery lug,open barrel, closed barrel, etc.
1.Made of high-quality steel, durable enough for long term service.
2.Accurate jaw design guarantees perfect crimping every time
3.Upgraded structure brings an effortless and stable operation
In the past decades, our team committed to R&D and released various new style crimping tools to make the crimping more efficiently and easily. To meet requirements in different countries, we also made the tools in both metric and imperial standards.
IWISS tools are designed to create more efficient power to make perfect crimping. We keep working to fulfill our commitment to providing every customer with high-quality tools for electrical applications.
This document provides information on the mission, vision, certifications, facilities, machinery, processes, and products of a company that manufactures custom designed heavy commercial vehicle bodies. The company's mission is to become a leading manufacturer in this industry by offering flexible, high-quality products at competitive rates. It aims to create a positive work environment for employees and maintain long-term relationships with vendors and suppliers. The company also strives to contribute to economic growth and environmental preservation in the local community.
18V Slitting shear used for multiple industries for cold cutting on building sites and factories. The tool is designed primarily for the Ducting Trade.
The document discusses the M6 chipbreaker tool from Seco Tools. It provides 3 key points:
1. The M6 chipbreaker is intended for semi-roughing and roughing of steel with a well-balanced design that provides excellent chip control and relatively low cutting forces.
2. It is well-suited for machining ferritic and martensitic stainless steels and ductile cast iron. The M6 chipbreaker is available in several grades to enhance productivity and tool life.
3. Test results showed the M6 chipbreaker provided lower cutting forces, noise levels, chipping and crater wear compared to the M5 and MR7 chipbreakers, resulting in longer tool life.
CS Unitec's Catalog of Surface Finishing Tools and AccessoriesCS Unitec
CS Unitec's surface finishing tools and accessories offer professional power tools and abrasive accessories for surface finishing on steel, stainless steel, aluminum and other metals, as well as rigid plastics and wood.
CS Unitec Complete Magnetic Drill CatalogCS Unitec
CS Unitec's portable magnetic drills are idea for drilling structural steel and virtually any metal and are heavy-duty for use in construction and industry.
CS Unitec's core drill is a power tool for boring holes through concrete, reinforced concrete, brick, block, stone and masonry. Specialized core bits - hollow steel cylinders fitted with segmented diamond teeth - grind away the surface to create a hole.
CS Unitec Portable Magnetic Drills & AccessoriesCS Unitec
This document provides information on portable magnetic drilling machines made by CS Unitec. It describes the features and specifications of their line of portable magnetic drills, including electric, pneumatic, and hydraulic models. The drills are designed for continuous operation and drilling of structural steel and metal. They offer variable speed controls, quick-change tool holders, and safety features like overheating protection and electronic shutoff sensors.
CS Unitec Portable Magnetic Drilling MachineCS Unitec
The document provides information about portable magnetic drilling machines made by CS Unitec. It summarizes the key features of their line of magnetic drills including the maximum annular cutter, twist drill, and tapping diameters for each model. It also lists other specifications like stroke, weight, speed ranges, cooling features, and magnet sizes. Accessories and consumables like cutters, lubricants, and vacuum plates are also described. The document promotes CS Unitec as the industry leader in power-to-weight ratios and magnetic drilling strength and touts the reliability and customization of their machines.
This document provides information on Corner Drills and Drives from CSU Nitec, including:
1) Pneumatic and hydraulic corner drills and drives for drilling, reaming, and driving in tight spaces with self-closing throttles and built-in oilers.
2) Slow-speed, high-torque straight drive units that are ideal for heavy-duty reaming, tube expanding, and tapping applications.
3) Technical specifications for pneumatic corner drills, hydraulic corner drills, and pneumatic drive units including torque output, speed, power requirements, and dimensions.
CS Unitec AutoMAB1500 Portable Magnetic DrillCS Unitec
The AutoMAB 1500 is a heavy-duty, compact magnetic drill that automatically controls drill pressure and feed rate for optimal drilling performance. It has a powerful 10.5 amp motor and can drill holes up to 1-1/2 inches in diameter. The drill is portable, lightweight, and ideal for contractors, fabricators, and maintenance professionals. It comes with standard equipment like a carrying case, safety gear, and annular cutters.
Annular cutters can drill burr-free holes without predrilling or stepdrilling. They have precision-ground flutes for efficient chip clearance and hardened tool steel. This increases drilling productivity and reduces tool breakage compared to twist drills.
CS Unitec offers a complete line of High-Quality Non-Sparking, Non-Magnetic and Corrosion-Resistant Safety Tools. CS Unitec is a leader in special Copper Alloy Safety Hand Tools manufactured for use in high-risk areas where a spark can create a disaster.
This document is a parts list for CS UNITEC air motors and geared motors. It contains 52 numbered parts with descriptions and item numbers. It provides contact information for CS UNITEC, including their website and email for inquiries. The parts list contains components for the motor housing, gears, bearings, seals and other internal pieces of the air and geared motors. Prices are subject to change without notice.
Introduction of Cybersecurity with OSS at Code Europe 2024Hiroshi SHIBATA
I develop the Ruby programming language, RubyGems, and Bundler, which are package managers for Ruby. Today, I will introduce how to enhance the security of your application using open-source software (OSS) examples from Ruby and RubyGems.
The first topic is CVE (Common Vulnerabilities and Exposures). I have published CVEs many times. But what exactly is a CVE? I'll provide a basic understanding of CVEs and explain how to detect and handle vulnerabilities in OSS.
Next, let's discuss package managers. Package managers play a critical role in the OSS ecosystem. I'll explain how to manage library dependencies in your application.
I'll share insights into how the Ruby and RubyGems core team works to keep our ecosystem safe. By the end of this talk, you'll have a better understanding of how to safeguard your code.
Essentials of Automations: Exploring Attributes & Automation ParametersSafe Software
Building automations in FME Flow can save time, money, and help businesses scale by eliminating data silos and providing data to stakeholders in real-time. One essential component to orchestrating complex automations is the use of attributes & automation parameters (both formerly known as “keys”). In fact, it’s unlikely you’ll ever build an Automation without using these components, but what exactly are they?
Attributes & automation parameters enable the automation author to pass data values from one automation component to the next. During this webinar, our FME Flow Specialists will cover leveraging the three types of these output attributes & parameters in FME Flow: Event, Custom, and Automation. As a bonus, they’ll also be making use of the Split-Merge Block functionality.
You’ll leave this webinar with a better understanding of how to maximize the potential of automations by making use of attributes & automation parameters, with the ultimate goal of setting your enterprise integration workflows up on autopilot.
"Choosing proper type of scaling", Olena SyrotaFwdays
Imagine an IoT processing system that is already quite mature and production-ready and for which client coverage is growing and scaling and performance aspects are life and death questions. The system has Redis, MongoDB, and stream processing based on ksqldb. In this talk, firstly, we will analyze scaling approaches and then select the proper ones for our system.
zkStudyClub - LatticeFold: A Lattice-based Folding Scheme and its Application...Alex Pruden
Folding is a recent technique for building efficient recursive SNARKs. Several elegant folding protocols have been proposed, such as Nova, Supernova, Hypernova, Protostar, and others. However, all of them rely on an additively homomorphic commitment scheme based on discrete log, and are therefore not post-quantum secure. In this work we present LatticeFold, the first lattice-based folding protocol based on the Module SIS problem. This folding protocol naturally leads to an efficient recursive lattice-based SNARK and an efficient PCD scheme. LatticeFold supports folding low-degree relations, such as R1CS, as well as high-degree relations, such as CCS. The key challenge is to construct a secure folding protocol that works with the Ajtai commitment scheme. The difficulty, is ensuring that extracted witnesses are low norm through many rounds of folding. We present a novel technique using the sumcheck protocol to ensure that extracted witnesses are always low norm no matter how many rounds of folding are used. Our evaluation of the final proof system suggests that it is as performant as Hypernova, while providing post-quantum security.
Paper Link: https://eprint.iacr.org/2024/257
Northern Engraving | Nameplate Manufacturing Process - 2024Northern Engraving
Manufacturing custom quality metal nameplates and badges involves several standard operations. Processes include sheet prep, lithography, screening, coating, punch press and inspection. All decoration is completed in the flat sheet with adhesive and tooling operations following. The possibilities for creating unique durable nameplates are endless. How will you create your brand identity? We can help!
This talk will cover ScyllaDB Architecture from the cluster-level view and zoom in on data distribution and internal node architecture. In the process, we will learn the secret sauce used to get ScyllaDB's high availability and superior performance. We will also touch on the upcoming changes to ScyllaDB architecture, moving to strongly consistent metadata and tablets.
How information systems are built or acquired puts information, which is what they should be about, in a secondary place. Our language adapted accordingly, and we no longer talk about information systems but applications. Applications evolved in a way to break data into diverse fragments, tightly coupled with applications and expensive to integrate. The result is technical debt, which is re-paid by taking even bigger "loans", resulting in an ever-increasing technical debt. Software engineering and procurement practices work in sync with market forces to maintain this trend. This talk demonstrates how natural this situation is. The question is: can something be done to reverse the trend?
LF Energy Webinar: Carbon Data Specifications: Mechanisms to Improve Data Acc...DanBrown980551
This LF Energy webinar took place June 20, 2024. It featured:
-Alex Thornton, LF Energy
-Hallie Cramer, Google
-Daniel Roesler, UtilityAPI
-Henry Richardson, WattTime
In response to the urgency and scale required to effectively address climate change, open source solutions offer significant potential for driving innovation and progress. Currently, there is a growing demand for standardization and interoperability in energy data and modeling. Open source standards and specifications within the energy sector can also alleviate challenges associated with data fragmentation, transparency, and accessibility. At the same time, it is crucial to consider privacy and security concerns throughout the development of open source platforms.
This webinar will delve into the motivations behind establishing LF Energy’s Carbon Data Specification Consortium. It will provide an overview of the draft specifications and the ongoing progress made by the respective working groups.
Three primary specifications will be discussed:
-Discovery and client registration, emphasizing transparent processes and secure and private access
-Customer data, centering around customer tariffs, bills, energy usage, and full consumption disclosure
-Power systems data, focusing on grid data, inclusive of transmission and distribution networks, generation, intergrid power flows, and market settlement data
"Scaling RAG Applications to serve millions of users", Kevin GoedeckeFwdays
How we managed to grow and scale a RAG application from zero to thousands of users in 7 months. Lessons from technical challenges around managing high load for LLMs, RAGs and Vector databases.
Skybuffer SAM4U tool for SAP license adoptionTatiana Kojar
Manage and optimize your license adoption and consumption with SAM4U, an SAP free customer software asset management tool.
SAM4U, an SAP complimentary software asset management tool for customers, delivers a detailed and well-structured overview of license inventory and usage with a user-friendly interface. We offer a hosted, cost-effective, and performance-optimized SAM4U setup in the Skybuffer Cloud environment. You retain ownership of the system and data, while we manage the ABAP 7.58 infrastructure, ensuring fixed Total Cost of Ownership (TCO) and exceptional services through the SAP Fiori interface.
Conversational agents, or chatbots, are increasingly used to access all sorts of services using natural language. While open-domain chatbots - like ChatGPT - can converse on any topic, task-oriented chatbots - the focus of this paper - are designed for specific tasks, like booking a flight, obtaining customer support, or setting an appointment. Like any other software, task-oriented chatbots need to be properly tested, usually by defining and executing test scenarios (i.e., sequences of user-chatbot interactions). However, there is currently a lack of methods to quantify the completeness and strength of such test scenarios, which can lead to low-quality tests, and hence to buggy chatbots.
To fill this gap, we propose adapting mutation testing (MuT) for task-oriented chatbots. To this end, we introduce a set of mutation operators that emulate faults in chatbot designs, an architecture that enables MuT on chatbots built using heterogeneous technologies, and a practical realisation as an Eclipse plugin. Moreover, we evaluate the applicability, effectiveness and efficiency of our approach on open-source chatbots, with promising results.
"$10 thousand per minute of downtime: architecture, queues, streaming and fin...Fwdays
Direct losses from downtime in 1 minute = $5-$10 thousand dollars. Reputation is priceless.
As part of the talk, we will consider the architectural strategies necessary for the development of highly loaded fintech solutions. We will focus on using queues and streaming to efficiently work and manage large amounts of data in real-time and to minimize latency.
We will focus special attention on the architectural patterns used in the design of the fintech system, microservices and event-driven architecture, which ensure scalability, fault tolerance, and consistency of the entire system.
Main news related to the CCS TSI 2023 (2023/1695)Jakub Marek
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
Connector Corner: Seamlessly power UiPath Apps, GenAI with prebuilt connectorsDianaGray10
Join us to learn how UiPath Apps can directly and easily interact with prebuilt connectors via Integration Service--including Salesforce, ServiceNow, Open GenAI, and more.
The best part is you can achieve this without building a custom workflow! Say goodbye to the hassle of using separate automations to call APIs. By seamlessly integrating within App Studio, you can now easily streamline your workflow, while gaining direct access to our Connector Catalog of popular applications.
We’ll discuss and demo the benefits of UiPath Apps and connectors including:
Creating a compelling user experience for any software, without the limitations of APIs.
Accelerating the app creation process, saving time and effort
Enjoying high-performance CRUD (create, read, update, delete) operations, for
seamless data management.
Speakers:
Russell Alfeche, Technology Leader, RPA at qBotic and UiPath MVP
Charlie Greenberg, host
Have you ever been confused by the myriad of choices offered by AWS for hosting a website or an API?
Lambda, Elastic Beanstalk, Lightsail, Amplify, S3 (and more!) can each host websites + APIs. But which one should we choose?
Which one is cheapest? Which one is fastest? Which one will scale to meet our needs?
Join me in this session as we dive into each AWS hosting service to determine which one is best for your scenario and explain why!
What is an RPA CoE? Session 1 – CoE VisionDianaGray10
In the first session, we will review the organization's vision and how this has an impact on the COE Structure.
Topics covered:
• The role of a steering committee
• How do the organization’s priorities determine CoE Structure?
Speaker:
Chris Bolin, Senior Intelligent Automation Architect Anika Systems
Dandelion Hashtable: beyond billion requests per second on a commodity serverAntonios Katsarakis
This slide deck presents DLHT, a concurrent in-memory hashtable. Despite efforts to optimize hashtables, that go as far as sacrificing core functionality, state-of-the-art designs still incur multiple memory accesses per request and block request processing in three cases. First, most hashtables block while waiting for data to be retrieved from memory. Second, open-addressing designs, which represent the current state-of-the-art, either cannot free index slots on deletes or must block all requests to do so. Third, index resizes block every request until all objects are copied to the new index. Defying folklore wisdom, DLHT forgoes open-addressing and adopts a fully-featured and memory-aware closed-addressing design based on bounded cache-line-chaining. This design offers lock-free index operations and deletes that free slots instantly, (2) completes most requests with a single memory access, (3) utilizes software prefetching to hide memory latencies, and (4) employs a novel non-blocking and parallel resizing. In a commodity server and a memory-resident workload, DLHT surpasses 1.6B requests per second and provides 3.5x (12x) the throughput of the state-of-the-art closed-addressing (open-addressing) resizable hashtable on Gets (Deletes).
"Frontline Battles with DDoS: Best practices and Lessons Learned", Igor IvaniukFwdays
At this talk we will discuss DDoS protection tools and best practices, discuss network architectures and what AWS has to offer. Also, we will look into one of the largest DDoS attacks on Ukrainian infrastructure that happened in February 2022. We'll see, what techniques helped to keep the web resources available for Ukrainians and how AWS improved DDoS protection for all customers based on Ukraine experience
GraphRAG for LifeSciences Hands-On with the Clinical Knowledge Graph
CS Unitec Reciprocating Saws
1. Reciprocating Air Saws ATEX Certified
Compact, Quiet & Reliable
Low Vibration/Low Air Volume
Cut Pipe, Structural Steel, Sheet
Metal, Fiberglass, Plastic and More.
RECIPROCATING SAWS
• Piston air motors use low air volume (CFM)
while maintaining a fast cutting speed (2000 PL Saws - For High-volume p. 5
to 10,000 strokes per minute) Production Environments
• Safe around gas and other flammable
materials; recommended for fire and rescue
applications where high CFM isn't available
• ATEX Certified – for use in hazardous areas
• CL and PL saws use standard hand hacksaw
blades; convert to a 3/4" blade size simply by
changing the nosepiece
• Rugged saw bodies constructed of heavy- CL Saws - For Demanding
p. 6
duty cast steel and aluminum Maintenance Applications
• Built-in lubrication system automatically
lubricates the motor
• Safety STOP/Isolator button disconnects
air supply
JP Saws - For Fiberglass
p. 7
and Sheet Metal Production
Cengar Air Saw Blades
1/2" Wide Bi-metal Blades (for CL50, JP901 and PL905)
HB300/18 Hand 18 TPI 12" L
HB300/24 Hand 24 TPI 12" L
HB300/32 Hand 32 TPI 12" L
MC220/24 Machine 24 TPI 81/2" L
MYN150/18 Notched Yellow 18 TPI 6" L
MYT150/18 Tapered Yellow 18 TPI 6" L
3/4" Wide Bi-metal Blades (for CL75)
MB150/18 Machine 18 TPI 6" L
MB200/10-14 Machine 10/14 TPI 8" L
Lubricating Oils (see p. 29) MB200/18 Machine 18 TPI 8" L
• ProLube™ is a super-premium, low-viscosity
synthetic air tool lubricant MB200/24 Machine 24 TPI 8" L
MB250/18 Machine 18 TPI 10" L
• ProLube-ATL/AF is a special blend preventing
MB250/24 Machine 24 TPI 10" L
freezing in cold climate conditions
MB300/10-14 Machine 10/14 TPI 12" L
MS Cleaner (MS 9105) MB300/18 Machine 18 TPI 12" L
• An ideal conditioner for air tools used underwater
4 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
2. ReciprocatingECO32-TAK
ECO32-T and Air Saws ATEX Certified
Reversible motor for drilling and tappingand more
Ideal for cutting pipe, metals, fiberglass applications
Cutter
capacity
11/4" dia.
RECIPROCATING SAWS
Model PL905
Sturdy air saw for continuous use
Low Vibration • Low Noise
• Ideal for high-volume production applications
such as cutting steel, repairing wooden pallets,
building and repairing truck bodies and cutting
fiberglass
• Also widely used by oil and gas contractors and
fire rescue services
• Sturdy cast steel and aluminum saw body
• Low air volume – only 4 CFM
• 7/8" blade stroke, up to
2000 strokes per minute
• Fitted with easy-to-use
Cut Sheet Metal STOP/Isolator button on
the handle for safety when
changing blades
Standard Equipment:
carrying case, five
• Uses any 1/2" (12mm) wide
MC220/24 saw blades, Bi-metal hand, machine or
air tool oil, CD operating yellow blades
manual, allen key. Cut Nails
Cengar Saw Blades and Accessories (see page 4) Model PL905
• 1/2" wide Bi-metal Blades suit a wide range Motor Power 1 HP
of applications Stroke Length 7/8"
Strokes per Min. 2000
Weight 5 1/4 lbs.
Length x Height x Width 113/4" x 51/4" x 15/8"
Air Consumption 4 CFM
Air Pressure 90 PSI
Air Connection 1/4" NPT
Air Hose 1/4" ID
Noise Level (dB) 69
Vibration Level (m/s2) 1.73
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 5
3. Reciprocating Air Saws ATEX Certified
Ideal for cutting metal, timber and fiberglass
RECIPROCATING SAWS
Models CL50 & CL75
Rugged air saws for versatile applications
Low Vibration • Low Noise
• Workhorses for use in the fabrication,
shipbuilding, ship repair, oil and
petrochemical, boat building and
aircraft maintenance fields
• Also utilized by fire and rescue
professionals
• 13/4" blade stroke, up to 1200 strokes
per minute
• Fitted with easy-to-use STOP/Isolator
button on the handle for safety when
changing blades
• CL50 uses any 1/2" (12mm) wide
Bi-metal hand or machine blade and
can be easily converted to a CL75 by
changing the nosepiece Standard Equipment: carrying case,
• CL75 uses a 3/4"
(19mm) wide five MC220/24 saw blades, air tool oil,
Bi-metal machine blade CD operating manual, allen key.
Models CL50 & CL75
Cengar Saw Blades and Accessories (see page 4)
Motor Power 1 HP
• 1/2" and 3/4" wide Bi-metal Blades suit a wide Stroke Length 1 3/4"
range of applications
Strokes per Min. 1200
• To fit our 3/4" Bi-metal blades, order 3/4" Weight 51/2 lbs.
nosepiece – Part. No. 5075
Length x Height x Width 153/4" x 51/4" x 15/8"
Air Consumption 53/4 CFM
Air Pressure 90 PSI
Air Connection 1/4" NPT
Air Hose 1/4" ID
Noise Level (dB) 83
Vibration Level (m/s2) 3.69
6 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
4. ReciprocatingECO32-TAK
ECO32-T and Air Saws ATEX Certified
Ideal for cutting fiberglass, light-gauge metal & fiberboard
Reversible motor for drilling and tapping applications
Cutter
capacity
11/4" dia.
RECIPROCATING SAWS
Model JP901
Speedy, lightweight air saw for repair and construction environments
Low Vibration • Low Noise
• Ideal for cutting fiberglass,
light-gauge metal and fiberboard
up to 3/8" (10mm) thick
• Utilized by boat builders and in the
construction and repair of car, bus
and truck bodies
• Low air consumption – only 4 CFM
• 3/8" blade stroke, up to 10,000 strokes
per minute
• Has automatic lubrication and an easy-
to-use STOP/Isolator button on the
handle for safety when changing blades
• JP901 uses any 1/2" (12mm) wide
Bi-metal hand, machine or yellow
blades and can be easily converted
to use 3/4" blades by simply changing
the nosepiece
Standard Equipment: carrying case, five MYN150/18
saw blades, five MYT150/18 saw blades, air tool oil, Model JP901
CD operating manual, allen key.
Motor Power 1 HP
Stroke Length 3/8"
Cengar Saw Blades and Accessories (see page 4)
Strokes per Min. 10,000
• 1/2" and 3/4" wide Bi-metal Blades suit a wide Weight 31/2 lbs.
range of applications Length x Height x Width 103/4" x 23/4" x 15/8"
• To fit our 3/4" Bi-metal blades, order 3/4" Air Consumption 4 CFM
nosepiece – Part. No. 5075 Air Pressure 75 PSI
Air Connection 1/4" NPT
Air Hose 1/4" ID
Noise Level (dB) 69
Vibration Level (m/s2) 1.23
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 7
5. Portable Reciprocating Saws
The most powerful
in the industry!
Hand-held or clamp-on cutting
RECIPROCATING SAWS
in tough environments
ATEX Certified
Pneumatic • Hydraulic • Electric
The CAT - 1.3 HP Pneumatic
Ideal for a wide range of industries, Reciprocating Saw p. 10
including subsea, gas utilities,
offshore oil, petrochemical, power
generation, industrial plant
maintenance and construction
• Fast cutting of pipe, structural steel,
bolts, nails, pallets and other material
• The best power-to-weight ratios The WOLF - 1.6 HP Pneumatic
Reciprocating Saw p. 11
in the industry
• Compact size allows cutting in
confined spaces
• ANC gear drive reduces friction and
increases gear life and power output
• Cut steel pipe and channel up to
6" dia. (or plastic pipe up to 8" dia.)
• 90˚ cuts with optional clamps
The SHARK - 2 HP Hydraulic
p. 12
Reciprocating Saw
Two Models:
Spade (below) or D-handle
(right) available.
Pipe Clamps for The FOX - 9.5 and 12 Amp
p. 12
90˚ Cutting Electric Reciprocating Saws
Cut faster by increasing
your leverage 5x
Pipe Clamp for Pipes & Profiles
while safely Model No. CP1 Universal Clamp
securing the • Easily attaches to recip saws and
90˚ saw with our
Pipe Clamps.
portable hacksaws for 90˚ cuts in
tight spaces
• Self-aligning feet adjust to
1/2" the form of the workpiece
- 2" Pipe Vise Clamp – Model No. 259.983 (round, square and angled)
2 1/2" - 4" Pipe Vise Clamp – Model No. 563.100 • 1/2" to 6" capacity with recip
1/2" - 6" Pipe Chain Clamp – Model No. 251.259 saws – see page 16 for use
with portable hacksaws
8 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
6. Reciprocating Saws
The New Generation Gear Head
ANC = All-round Needle-bearing Crank Drive
CS Unitec's reciprocating saws cut faster and last longer
RECIPROCATING SAWS
than other saws in their class. The ANC gear drive and
heavy-duty air or electric motor provide the best power-to-weight ratio in the industry.
Universal 1/2" tang, double- Ergonomically Pipe Patented Silicone Patented ANC Powerful, heavy-
tang or M-Tooth blade moves shaped clamp saw blade gasket square gear duty pneumatic
in aggressive orbital action housing grip connection mount lift rod drive or electric motor
ANC Gear Drive: Low Friction • High Torque
The new, unique design of the ANC gear:
• reduces friction and wear, resulting in less
heat and longer service life.
• resists dust and water, making the gear head
maintenance free.
• allows for aggressive high-torque cutting,
providing good chip flow and long blade life.
Reciprocating Saw Blades
Standard Blades Extremely versatile, CS Unitec's
All CS Unitec reciprocating saws can use reciprocating saws use the
the widely available standard reciprocating universal 1/2" tang or special
blades with the 1/2" universal tang. double-tang saw blades (see page 13).
Our extra-thick saw blades resist
Heavy-duty Blades bending and cut pipe at right angles
These blades are much thicker than with a pipe clamp.
standard blades and have a stronger
double-tang mount for heavy-duty In addition, CS Unitec's Mega Sharp
cutting, either free-hand or with a clamp. M-Tooth saw blades (see page 13)
have a unique, patented tooth
geometry that allows these blades
Cut in M-Tooth Blades to cut quickly with each stroke,
Both Directions! Unique tooth geometry allows forward and back, saving time
these blades to cut in both and money.
directions – twice as fast!
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 9
7. 1.3 HP Pneumatic Reciprocating Saw
Ideal for cutting pipes, structural steel, pallets and more
The
RECIPROCATING SAWS
CAT
Model 5 1217 0020
Use hand-held or with a clamp
• Cuts steel pipe and channel 1/2" to 4" dia., plastic
pipe to 8" dia.
• Ideal for the toughest use in refineries, chemical
plants, gas utilities, construction, offshore oil,
mining, marine and demolition industries
• 1.3 HP air motor provides more power than
conventional air saws
Model 5 1217 0020 includes carrying case
and two No. 1001 heavy-duty blades. • 11/8" blade stroke for fast, efficient cutting
• Can be mounted on a pipe clamp to make
ATEX Certified 90˚ cuts
• Variable speed of 0-1800 strokes per minute
• Accepts universal saw blades or thicker, heavy-
duty double-tang saw blades (see page 13)
• Molded rubber boot for ergonomic grip
• One-year warranty
Pipe Clamps for Straight
Cutting up to 6" dia.
• Increase leverage
5x for faster cutting
Saw Kit (5 1217 0060) • Safely secure the
includes saw, 6" pipe clamp, saw while cutting
case and five No. 1001
heavy-duty blades.
Model 5 1217 0020
Motor Power 1.3 HP
Reciprocating Saw Blades
and Accessories (see page 13) Stroke Length 1 1/8"
Strokes per Min. 0-1800
• Universal saw blades
Weight 9 lbs.
• Thicker, heavy-duty double- Length 15 7/8"
tang blades for 90˚ cuts Air Consumption 46 CFM
• M-Tooth blades to cut on Air Pressure 90 PSI
forward and back stroke Air Connection 1/2" NPT (ID)
Saw Kit Order Model 5 1217 0060
10 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
8. 1.6 HP Pneumatic Reciprocating Saw
ECO32-T and ECO32-TAK
Ideal for cutting pipe, structural steel and other materials
Reversible motor for drilling and tapping applications
Cutter
Selector switch for capacity
straight or orbital stroke 11/4" dia.
RECIPROCATING SAWS
The
WOLF
Model 5 6005 0010
Use hand-held or with a clamp
Shown with side handle
• Cuts steel pipe and channel 1/2" to 6" dia., plastic pipe
to 8" dia.
• Powerful 1.6 HP motor with reciprocating action for
steel and long orbital stroke for cutting soft materials
including wood, plastic and aluminum
• Can be mounted on a pipe clamp to make 90˚ cuts
• 11/8" blade stroke for fast, efficient cutting Pipe Clamps for Straight
• Selector switch changes stroke setting to either Cutting up to 6" dia.
straight or orbital • Increase leverage
• Variable speed from 0-2200 strokes per minute 5x for faster cutting
• Accepts universal saw blades • Safely secure the
saw while cutting
or thicker, heavy-duty double-tang
saw blades (see page 13)
• Molded rubber boot for
ergonomic grip; side
handle included
• One-year warranty
Saw Kit (5 6005 0060) includes saw, 6" pipe
clamp, case, side handle and five No. 1001
heavy-duty blades.
Model 5 6005 0010
Motor Power 1.6 HP
Reciprocating Saw Blades Stroke Length 1 1/8"
and Accessories (see page 13) Strokes per Min. 0-2200
• Universal saw blades Weight 10 3/4 lbs.
• Thicker, heavy-duty double- Length 17 3/4"
tang blades for 90˚ cuts Air Consumption 51 CFM
• M-Tooth blades to cut on Air Pressure 90 PSI
forward and back stroke Air Connection 1/2" NPT (ID)
Saw Kit Order Model 5 6005 0060
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 11
9. ECO50-T and ECO50-TAK
Hydraulic Reciprocating Saw
Reversible motor for drilling and tapping applications
Subsea, mining, utility and construction applications
Cutter
capacity
2" dia. The SHARK
RECIPROCATING SAWS
• Marine, mining, utility and
construction applications
• Operate on 2000 PSI / 6 GPM Model 5 1219 0010
(up to 13 GPM) hydraulic oil Use hand-held or with a clamp
• Cut wood up to 6" dia., metal
up to 3/4" dia.
Model 5 1219 0010
Reciprocating Saw Blades Motor Power 2 HP
and Accessories (see page 13) Oil Pressure 2000 PSI
• Universal saw blades Oil Flow 6 GPM (up to 13)
Strokes per Min. 1700
• Thicker, heavy-duty double-
tang blades for 90˚ cuts Weight 13.2 lbs.
Hydraulic Connection M 18 x 1.5 Male
• M-Tooth blades to cut on
forward and back stroke Hose ID* 1/2" ID with 1/2" FF Couplings
* Hoses are not included
Electric Reciprocating Saw Models 5 6002 0000 and 5 6002 6000
with spade handle. Model 5 6002 6000
has variable-speed
The FOX control dial.
mini hacksaws –
industry's most powerful
electric recip saws!
• Cut steel pipe and channel 1/2" to
4" dia., plastic pipe to 8" dia.
• Powerful 9.5 and 12 Amp motors,
110 Volt/60Hz (or 220 Volt/50Hz) Model 5 6002 7000 with
D-handle variable-
• Ideal for plumbing and electrical Accept universal speed trigger.
contractors as well as demolition saw blades or
jobs, pallet cutting and more thicker, heavy-
duty double-tang
• 11/8" blade stroke for fast cutting saw blades (see
• 0-2200 variable stroke speed for page 13)
models 5 6002 6000 and 5 6002 7000
Standard Stroke Strokes Weight
Model No. Power Length per Min. Handle Style Length (lbs.)
equipment
includes 2"
Single Speed
pipe clamp
(#259.983), 5 6002 0000 9.5 Amp, 110V* 11/8" 2200 Spade 19" 6
carrying case Variable Speed
and two No. 5 6002 6000** 12 Amp, 110V* 11/8" 0-2200 Spade 19" 6
1001 blades
5 6002 7000** 9.5 Amp, 110V* 11/8" 0-2200 D-handle 19" 6
* 220 Volt also available ** 5 6002 6000 with speed control dial, 5 6002 7000 with variable-speed trigger.
12 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
10. Reciprocating Saw Blades
Super quick and precise for pipe, steel, plastic, etc.
**Use ProLube™ Specialty Lubricants with your Reciprocating Saw Blades to help your
tools work cooler, longer and more efficiently. ProLube Lubricants are non-toxic and
ideal for stainless steel and hard metal cutting applications. See page 31 for details.**
RECIPROCATING SAW BLADES
Extra-thick Blades for 90˚ Cutting with a Pipe Clamp, Double Shank*
No. 1001 Cuts pipe up to 2" 8 TPI 6" L x 1" W x .060" T
No. 1002 Cuts pipe up to 4" 8 TPI 8" L x 1" W x .060" T
No. 007D/200* Cuts pipe up to 4" M-Tooth 8" L x 1" W x .050" T
* 007D/200 has universal 1/2" tang • Ask for special blades to cut stainless steel.
Heavy-duty HSS-Bi-metal Blades for Freehand Sawing, Double Shank
Made of tough, resilient steel with 10/14 variable tooth pitch. The large blade width and double-shank mount
deliver excellent cutting performance and durability.
No. 1005 10/14 TPI 6" L x 1" W x .035" T
No. 1003 10/14 TPI 8" L x 1" W x .035" T
No. 1004 10/14 TPI 12" L x 1" W x .035" T
General-purpose Bi-metal Saw Blades with Universal 1/2" Shank
Metal 1/8" and Thicker
No. 3013/150 14 TPI 6" L x 3/4" W x .035" T
No. 3013/200 14 TPI 8" L x 3/4" W x .035" T
No. 3018/280 10 TPI 12" L x 3/4" W x .035" T
Metal up to 1/8" Thick
No. 3014/150 18 TPI 6" L x 3/4" W x .035" T
Metal up to 1/8" Thick (for Curved Cuts)
No. 3017/90 18 TPI 35/8" L x 5/16" W x .035" T
Plastic, Wood, Plasterboard
No. 3021/150 6 TPI 6" L x 3/4" W x .035" T
No. 3021/225 6 TPI 8" L x 3/4" W x .035" T
No. 3021/300 6 TPI 12" L x 3/4" W x .035" T
All Woods with Steel (i.e. Embedded Nails)
No. 810C/150 8/10 TPI 6" L x 3/4" W x .035" T
No. 810C/225 8/10 TPI 9" L x 3/4" W x .035" T
Cast Steel, Ductile Iron, Ceramics and Glass Fiber Products
No. D12/200 Tungsten Carbide Coarse 8" L x 3/4" W
Mega Sharp M-Tooth Saw Blades for Freehand Cutting with Standard 1/2" Shank
CUTS TWICE AS FAST!
M42 Bi-metal for cutting steel and stainless steel
Metal 1/8" and Thicker
No. 007/150 M-Tooth 6" L x 3/4" W x .035" T
No. 007/200 M-Tooth 8" L x 3/4" W x .035" T
No. 007/280 M-Tooth 12" L x 3/4" W x .035" T Cuts in
The patented M-Tooth saw
Metal up to 1/8" Thick blade cuts 2x faster than ordinary Both Directions!
No. 006/150 M-Tooth 6" L x 3/4" W x .035" T blades. The teeth are designed
to cut on the forward and back
No. 006/250 M-Tooth 7" L x 3/4" W x .035" T strokes, thereby saving time.
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 13