CS Unitec offers Pneumatic, Electric and Hydraulic models and a wide range of options for portable cutting of pipe, structural steel, tanks and other materials.
CS Unitec offers pneumatic and hydraulic models of chain saws. They are ideal for use in polyethylene plants, petrochemical industries, utilities, underground mines and marine applications.
CS Unitec Portable Magnetic Drills: AIRBOR AB-4300CS Unitec
This document summarizes the specifications of the AIRBORTM AB-4300 portable magnetic drill. It has three main features:
1) It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments.
2) It has a fail-safe permanent magnet that is activated and deactivated by air pressure, and will not disengage if air flow is lost.
3) It can drill holes up to 2-1/16 inches in diameter and has a powerful 1.6 HP pneumatic motor and long drill stroke of up to 10-1/4 inches.
The document is describing the AIRBORTM AB-4300 portable magnetic drill. [1] It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments. [2] It has a 1.6 HP pneumatic motor, can drill up to 2-1/16" diameters, and has a long drill stroke of up to 10-1/4". [3] It is approved for use in hazardous atmospheres by ATEX and features automatic lubrication to reduce sparking.
CS Unitec Reciprocating Air Saws are compact, quiet, and reliable. Models are ideal for cutting pipe, metals, fiberglass, timber, light-gauge metal & fiberboard. Portable reciprocating saws are also available for hand-held or clamp-on cutting in tough environments.
This document provides information about the P1 portable magnetic drill. It can drill holes up to 1-3/8 inches in diameter using annular cutters or twist drills. The drill features a 10 amp motor, weighs 26.5 pounds, and has a 4 inch stroke length. It comes equipped with safety features and accessories like a carrying case, lubrication pump, and safety strap. Optional accessories allow it to function as a standard drill press as well.
CS Unitec Portable Magnetic Drills: AutoMAB 1500CS Unitec
The AutoMAB 1500 is a portable magnetic drill with a 1-1/2 inch cutter capacity. It has a 10.5 amp double insulated motor and weighs 37.5 lbs, making it compact and lightweight. It features an automatic feed mechanism that controls drill pressure and feed rate for optimal cutting. Standard equipment includes automatic lubrication, safety accessories, and annular cutters for drilling up to 1-1/2 inches in diameter.
CS Unitec offers pneumatic and hydraulic models of chain saws. They are ideal for use in polyethylene plants, petrochemical industries, utilities, underground mines and marine applications.
CS Unitec Portable Magnetic Drills: AIRBOR AB-4300CS Unitec
This document summarizes the specifications of the AIRBORTM AB-4300 portable magnetic drill. It has three main features:
1) It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments.
2) It has a fail-safe permanent magnet that is activated and deactivated by air pressure, and will not disengage if air flow is lost.
3) It can drill holes up to 2-1/16 inches in diameter and has a powerful 1.6 HP pneumatic motor and long drill stroke of up to 10-1/4 inches.
The document is describing the AIRBORTM AB-4300 portable magnetic drill. [1] It is powered completely by compressed air, making it safer than electric magnetic drills in hazardous environments. [2] It has a 1.6 HP pneumatic motor, can drill up to 2-1/16" diameters, and has a long drill stroke of up to 10-1/4". [3] It is approved for use in hazardous atmospheres by ATEX and features automatic lubrication to reduce sparking.
CS Unitec Reciprocating Air Saws are compact, quiet, and reliable. Models are ideal for cutting pipe, metals, fiberglass, timber, light-gauge metal & fiberboard. Portable reciprocating saws are also available for hand-held or clamp-on cutting in tough environments.
This document provides information about the P1 portable magnetic drill. It can drill holes up to 1-3/8 inches in diameter using annular cutters or twist drills. The drill features a 10 amp motor, weighs 26.5 pounds, and has a 4 inch stroke length. It comes equipped with safety features and accessories like a carrying case, lubrication pump, and safety strap. Optional accessories allow it to function as a standard drill press as well.
CS Unitec Portable Magnetic Drills: AutoMAB 1500CS Unitec
The AutoMAB 1500 is a portable magnetic drill with a 1-1/2 inch cutter capacity. It has a 10.5 amp double insulated motor and weighs 37.5 lbs, making it compact and lightweight. It features an automatic feed mechanism that controls drill pressure and feed rate for optimal cutting. Standard equipment includes automatic lubrication, safety accessories, and annular cutters for drilling up to 1-1/2 inches in diameter.
This document provides information about various modules for cutting systems, including:
- Loaders, joggers, sorting and buffering equipment that prepare and organize paper reams for cutting
- Cutting machines ranging from 1150-3000mm that precisely cut paper and other materials
- Unloading equipment that efficiently remove cut materials from the cutting area using grippers, pushers and air tables
- The ROBOCUT is highlighted as a fully automatic cutting system that works with a 4 axis robot and precision unloader to cut and remove materials.
CS Unitec Drill and Drive Units Catalog PagesCS Unitec
CS Unitec's catalog pages for quality industrial power tools including drill and drive units, tube rolling motors, tube expanding motors, electri drills and drive units, and drill motors and power drivers.
Mirage Machines is a UK-based company founded in 1993 that designs and manufactures portable on-site machining equipment. The company's products include flange facing machines, orbital milling machines, pipe cutting saws, hot tapping machines, milling machines, and more. Mirage serves a variety of industries including oil and gas, wind, nuclear, and shipbuilding. The document provides an overview of Mirage's history and product lines.
This document provides information on welding carriages from SteelMax, including small and large fillet welders and a track burner. The small and large fillet welders use permanent magnets and closed-loop control systems to precisely position welding torches. The large fillet welder can also incorporate an optional oscillation unit. The track burner uses connected rails to accurately cut steel plates up to 45 degrees.
CS Unitec Portable Magnetic Drills: MAB 150CS Unitec
The document provides specifications for the MAB 150 portable magnetic drill. It has a 9.25 amp motor, weighs 24 lbs, and can drill holes up to 1.5 inches in diameter. It features automatic internal lubrication, integrated cable routing for safety, and electronic torque control. The MAB 150 comes with standard equipment like annular cutters, a shipping case, safety gear, and an operating manual.
The document discusses Barnes Engineered Pressure Sewer systems. It provides details on their grinder pumps, basin options, level control options, control panel options, and accessories. The grinder pumps come in a variety of horsepower sizes and configurations. The basins are available as fiberglass or with c-channel rails in various diameters and lengths. Level control options include the Environmentally Sealed Pressure Switch and float trees. Control panels include Stealth panels in simplex and duplex configurations. A range of accessories such as flexible piping, valves, and remote alarms are also available.
Auger Monster (JWC Environmental) - Modular Headworks System _ InglesVibropac
The document summarizes the Auger Monster modular headworks system. It is an all-in-one wastewater screening system that combines grinding, screening, washing and dewatering functions into a compact footprint. Solids and debris first enter a grinder that shreds materials. They then enter a perforated screening zone where solids are lifted and removed by a rotating auger. Wash water cleans solids off the screen and returns organic material to flow. Cleaned screenings are conveyed and can be compacted before disposal to reduce odors and costs. The system integrates multiple technologies to provide efficient pre-treatment with minimal civil works or installation requirements.
CS Unitec Wet stone Polisher/Grinder: EPO 1301CS Unitec
This document provides a list of 55 replacement parts for the CS UNITEC polishing machine Model EPO 1301, including the part number, item number, and description for each replacement part. It also lists the manufacturer and model number being summarized, as well as contact information for CS UNITEC.
CS Unitec Electric Magnetic Drills Schematic: MAB 525CS Unitec
The document provides a parts breakdown and list for the CS Unitec portable magnetic drill Model MAB 525. It includes 57 numbered parts for the motor breakdown and 32 numbered parts for the stand breakdown. The parts are identified by part number, description, and position number. The document also provides contact information for CS Unitec and instructions for ordering replacement parts or schematics.
CS Unitec Electric Drills and Drive Units: EHB 32/4.2 SCS Unitec
This document lists 65 parts that make up an electric drill model EHB 32/4.2. It provides the part number, item number, description, and any relevant notes for each part. Some parts are replacements for older part numbers. The document was produced by CS Unitec and lists their contact information at the bottom.
This document provides a parts list for a pneumatic nut runner model 6 1015 0010. It contains a list of over 60 individual parts identified by position number, item number, and description. It also provides information on the product group and effective date for the parts list.
This document is a parts list for a pneumatic concrete chain saw model CS 71773-0. It contains over 50 numbered parts and their descriptions. The parts are grouped into plates, governors, valves and other assemblies. Replacement kits are also listed. The document provides contact information for CS Unitec, Inc., the manufacturer located in Norwalk, Connecticut.
Anchor Stand Schematic for CS Unitec Core Drills: 256 955 ECS Unitec
This document contains two parts lists for an Anchor Stand Model 256 955 E. The first list contains 36 items that make up the main parts of the stand. The second list contains 18 items that make up the carriage assembly of the stand. Both lists provide the part number, description, and in some cases replacement part information for each item.
This document provides a parts list for a pneumatic nut runner model 6 1015 0010. It contains a list of over 60 individual parts identified by position number, item number, and description. It also provides information on the product group and effective date for the parts list.
Slotting, Tuck-Pointing and Grinding Tool: EBS 125.4CS Unitec
This document is a parts list for a Model EBS 125.4 concrete grinder from CS Unitec, Inc. It contains 58 numbered parts with descriptions and part numbers. Several parts are noted as replacements for older part numbers. The parts list provides the essential components and replacement part information for the Model EBS 125.4 concrete grinder.
CS Unitec Portable Pipe Sander Case StudyCS Unitec
1) AAMS Corporation took on projects to fabricate stainless steel pipe handrails for a new engineering college and aluminum ramp railings for a retail building, both requiring a polished finish.
2) AAMS' angle grinder could not produce the required polished finish and was difficult to maneuver, so they searched for an alternative finishing tool.
3) AAMS chose the CS Unitec pipe sander, finding it lightweight, portable, and suitable for the range of pipe diameters in their projects.
4) Using progressively finer abrasives, the pipe sander produced a polished finish on the rails in half the time of hand polishing, with less physical stress on operators.
This document is a parts list for the CS UNITEC Pneumatic Chain Saws Models 5 1007 0010-0020-0040. It contains 196 item numbers with descriptions of replacement parts for the chain saws. The parts list provides the item number, description, and in some cases old item numbers for each replacement part listed. It also notes that prices are subject to change without notice and they are not responsible for typographical errors.
This document provides information about various modules for cutting systems, including:
- Loaders, joggers, sorting and buffering equipment that prepare and organize paper reams for cutting
- Cutting machines ranging from 1150-3000mm that precisely cut paper and other materials
- Unloading equipment that efficiently remove cut materials from the cutting area using grippers, pushers and air tables
- The ROBOCUT is highlighted as a fully automatic cutting system that works with a 4 axis robot and precision unloader to cut and remove materials.
CS Unitec Drill and Drive Units Catalog PagesCS Unitec
CS Unitec's catalog pages for quality industrial power tools including drill and drive units, tube rolling motors, tube expanding motors, electri drills and drive units, and drill motors and power drivers.
Mirage Machines is a UK-based company founded in 1993 that designs and manufactures portable on-site machining equipment. The company's products include flange facing machines, orbital milling machines, pipe cutting saws, hot tapping machines, milling machines, and more. Mirage serves a variety of industries including oil and gas, wind, nuclear, and shipbuilding. The document provides an overview of Mirage's history and product lines.
This document provides information on welding carriages from SteelMax, including small and large fillet welders and a track burner. The small and large fillet welders use permanent magnets and closed-loop control systems to precisely position welding torches. The large fillet welder can also incorporate an optional oscillation unit. The track burner uses connected rails to accurately cut steel plates up to 45 degrees.
CS Unitec Portable Magnetic Drills: MAB 150CS Unitec
The document provides specifications for the MAB 150 portable magnetic drill. It has a 9.25 amp motor, weighs 24 lbs, and can drill holes up to 1.5 inches in diameter. It features automatic internal lubrication, integrated cable routing for safety, and electronic torque control. The MAB 150 comes with standard equipment like annular cutters, a shipping case, safety gear, and an operating manual.
The document discusses Barnes Engineered Pressure Sewer systems. It provides details on their grinder pumps, basin options, level control options, control panel options, and accessories. The grinder pumps come in a variety of horsepower sizes and configurations. The basins are available as fiberglass or with c-channel rails in various diameters and lengths. Level control options include the Environmentally Sealed Pressure Switch and float trees. Control panels include Stealth panels in simplex and duplex configurations. A range of accessories such as flexible piping, valves, and remote alarms are also available.
Auger Monster (JWC Environmental) - Modular Headworks System _ InglesVibropac
The document summarizes the Auger Monster modular headworks system. It is an all-in-one wastewater screening system that combines grinding, screening, washing and dewatering functions into a compact footprint. Solids and debris first enter a grinder that shreds materials. They then enter a perforated screening zone where solids are lifted and removed by a rotating auger. Wash water cleans solids off the screen and returns organic material to flow. Cleaned screenings are conveyed and can be compacted before disposal to reduce odors and costs. The system integrates multiple technologies to provide efficient pre-treatment with minimal civil works or installation requirements.
CS Unitec Wet stone Polisher/Grinder: EPO 1301CS Unitec
This document provides a list of 55 replacement parts for the CS UNITEC polishing machine Model EPO 1301, including the part number, item number, and description for each replacement part. It also lists the manufacturer and model number being summarized, as well as contact information for CS UNITEC.
CS Unitec Electric Magnetic Drills Schematic: MAB 525CS Unitec
The document provides a parts breakdown and list for the CS Unitec portable magnetic drill Model MAB 525. It includes 57 numbered parts for the motor breakdown and 32 numbered parts for the stand breakdown. The parts are identified by part number, description, and position number. The document also provides contact information for CS Unitec and instructions for ordering replacement parts or schematics.
CS Unitec Electric Drills and Drive Units: EHB 32/4.2 SCS Unitec
This document lists 65 parts that make up an electric drill model EHB 32/4.2. It provides the part number, item number, description, and any relevant notes for each part. Some parts are replacements for older part numbers. The document was produced by CS Unitec and lists their contact information at the bottom.
This document provides a parts list for a pneumatic nut runner model 6 1015 0010. It contains a list of over 60 individual parts identified by position number, item number, and description. It also provides information on the product group and effective date for the parts list.
This document is a parts list for a pneumatic concrete chain saw model CS 71773-0. It contains over 50 numbered parts and their descriptions. The parts are grouped into plates, governors, valves and other assemblies. Replacement kits are also listed. The document provides contact information for CS Unitec, Inc., the manufacturer located in Norwalk, Connecticut.
Anchor Stand Schematic for CS Unitec Core Drills: 256 955 ECS Unitec
This document contains two parts lists for an Anchor Stand Model 256 955 E. The first list contains 36 items that make up the main parts of the stand. The second list contains 18 items that make up the carriage assembly of the stand. Both lists provide the part number, description, and in some cases replacement part information for each item.
This document provides a parts list for a pneumatic nut runner model 6 1015 0010. It contains a list of over 60 individual parts identified by position number, item number, and description. It also provides information on the product group and effective date for the parts list.
Slotting, Tuck-Pointing and Grinding Tool: EBS 125.4CS Unitec
This document is a parts list for a Model EBS 125.4 concrete grinder from CS Unitec, Inc. It contains 58 numbered parts with descriptions and part numbers. Several parts are noted as replacements for older part numbers. The parts list provides the essential components and replacement part information for the Model EBS 125.4 concrete grinder.
CS Unitec Portable Pipe Sander Case StudyCS Unitec
1) AAMS Corporation took on projects to fabricate stainless steel pipe handrails for a new engineering college and aluminum ramp railings for a retail building, both requiring a polished finish.
2) AAMS' angle grinder could not produce the required polished finish and was difficult to maneuver, so they searched for an alternative finishing tool.
3) AAMS chose the CS Unitec pipe sander, finding it lightweight, portable, and suitable for the range of pipe diameters in their projects.
4) Using progressively finer abrasives, the pipe sander produced a polished finish on the rails in half the time of hand polishing, with less physical stress on operators.
This document is a parts list for the CS UNITEC Pneumatic Chain Saws Models 5 1007 0010-0020-0040. It contains 196 item numbers with descriptions of replacement parts for the chain saws. The parts list provides the item number, description, and in some cases old item numbers for each replacement part listed. It also notes that prices are subject to change without notice and they are not responsible for typographical errors.
CS Unitec Electric Drills and Drive Units: EHB 20/2.4CS Unitec
CS Unitec, Inc. is located in Norwalk, CT and provides an electric drill model EHB 20/2.4 and EHB 20/2.4 S. The document lists the parts for these electric drill models and their corresponding part numbers, with notes on any replacements. There are 50 individual parts listed, along with their item numbers and brief descriptions. Contact information is provided for CS Unitec at the bottom of each page.
This document is a parts list for a Hacksaw Model 5 1212 0010/0050. It contains 315 part numbers with descriptions. The parts include items like a motor, gears, pins, screws, springs and o-rings that make up the various components of the hacksaw.
Slotting, Tuck-Pointing and Grinding Tool: M 1509 FRCS Unitec
This document provides a parts list for a Tuck Point Machine Model F 1509 FR, listing 82 individual parts by position number, item number, and description. It includes replacement part numbers and notes on some items. The parts list is produced by CS UNITEC and is effective as of August 18, 2005.
The document contains parts lists for an air nut runner motor, gearbox, drive assembly, and level handle with oiler. It lists each part's position number, item number, description, and any reference numbers. The parts lists include bearings, rings, shafts, housings, and other components that make up the pneumatic tool.
CS Unitec, Inc. is a manufacturer of pneumatic mixers and related parts located in Norwalk, CT. The document provides parts lists and part numbers for a Pneumatic Mixer Model 7 1113 0010, its pneumatic motor, gearbox, and twist throttle components. Replacement part numbers are included to ensure customers can find the correct replacement parts for their CS Unitec pneumatic mixing equipment.
This document is a parts list for a Model L 1509 FR Angle Grinder from CS Unitec, Inc. located in Norwalk, CT. It contains 63 numbered parts with descriptions and part numbers. The parts listed are for the various components that make up the angle grinder, including the armature, magnetic field, motor case, control lever, electronic components, gears, bearings, spindle, switch, and guard.
CS Unitec's portable saws and tools are ideal for cutting pipe, structural steel, tanks, bolts, angle iron, concrete and other materials, including plastic and wood. We offer the widest range of portable pneumatic, electric and hydraulic saws in the industry.
Growth in industrial technology is increasing demand for new equipment like rebar processing machines. The document discusses various types of equipment used for cutting, bending, and tying rebar, including electric cutters that can cut rebar up to 16mm, heavy duty cutters that can cut rebar up to 42mm, wire rope cutters that can cut steel rope from 1.5mm to 20mm, and automatic bending machines that can bend rebar up to 32mm. It also discusses manual and automatic rebar tying machines. The equipment allows for high production volumes in minimal time with minimal waste and flexibility.
The hydraulic lopper can cut branches up to 2 inches in diameter. It has a rotating cutting head that can lock in position. Models are available in 74-inch and 87-inch lengths and weigh less than 6 pounds. The lopper uses an open/closed hydraulic system with a pistol grip handle. A swivel hose is also available to prevent tangling.
Swaging is a method of securing wire rope with fittings like aluminum sleeves and stainless steel tension swage studs. The connection will exceed the rated breaking strength of the wire rope or cable when properly applied. Therefore,swaging is widely used to accomplish tasks of light-duty projects and industrial applications. The proper swaging connections require quality sleeve,corresponding wire rope, and correct swaging tool. IWISS with its sub-brand iCrimp offers a series of swaging tools for virtually any type of swaging connections, from wire rope cutter, manual swager, bench mounted swager, to pneumatic swaging machine. The tools offer all key features of modern tools, such as:
1. Made of premium steel, the tools are high strength durable for long service life. With special surface treatment, the tools achieve a high degree of water proof, and corrosion-resistant
2. Accurate hole design and well-polished jaws makes every connection perfect with virtually all sleeve and wire rope in the market
3. Adjustable function makes tight and trust- worth connection even after a long time using.
4. Ergonomic handle ensures optimal force-transmission and anti-fatigue operation.
IWISS tools are designed to make connections much easier. We insist on innovation and released new style swaging tools in the past years. We don’t follow the trend, but we lead it.
The document discusses two handheld drilling motors, the CDM163 and CDM203. It summarizes their key features, which include durability, reliability, ergonomics, and a 2-year warranty. Their technical specifications are also provided, such as power output, RPM ranges, maximum drilling diameters, and weight. The document also introduces some associated drilling accessories like core bits and drilling stands.
I Norton Clippers CDM-sortiment ingår två modeller: CDM163 som har en motoreffekt på 1.800 W och är avsedd för våtborrning med borrkronor med en diameter på upp till 160 mm, och CDM203 med en motor på 2.000 W som kan användas för både torr- och våtborrning med borrkronor upp till 200 mm diameter. Den senare är särskilt lämplig för håltagning i armerad betong.
This document provides information on various types of pipes and pipe fittings available from a supplier, including:
- Plastic pipes made from fiberglass, HDPE, and other materials
- Manhole covers and gratings made from GRP and ductile iron
- Carbon steel and stainless steel seamless pipes in various grades and sizes
- Ductile iron pipes, fittings, valves and flanges protected by zinc coating and cement lining
- Casing pipes meeting API standards
- Pipe alignment and reforming clamps for welding small to large diameter pipes
- Pipe cutting and beveling machines for accurate cuts
- Expansion joints, hangers, hoses and other accessories to compensate for pipe movement
- Drain
This document provides information on various types of pipes and pipe fittings including:
- Plastic pipes made from fiberglass, HDPE, and PVC
- Manhole covers and gratings made from GRP and ductile iron
- Carbon steel and stainless steel seamless pipes for high temperature, fluid conveyance, and oil/gas/water pipelines
- Ductile iron pipes coated for corrosion protection and lined internally
- Mechanical pipe joining systems for water treatment plants
- Casing pipes for oil and gas wells
- Pipe alignment and reforming clamps for welding
- Pipe cutting and beveling machines
- Expansion joints, hangers, and hoses to compensate for pipe movement
Cembre HT81-U
Cembre HT81-U Hydraulic Crimping Tools
Cembre HT81-U hydraulic crimping tool is lightweight and compact for the crimping and compression of low and high voltage cable lugs, splices and connectors up to 240sqmm.
Cembre HT81-U crimping tool features a patented closure and release mechanism for the die locking pin - a wide range of electrical connectors can be crimped with a minimal number of die sets due to their unique, double groove styling.
Cembre HT81-U hydraulic crimping tool features a double speed crimping action : a fast advancing speed for rapid approach of the die sets to the electrical connector and a slower more powerful speed for crimping. For ease of operation and comfort of the electrical engineer or cable jointer the Cembre HT81-U crimp tool head can be fully rotated through 180 degrees.
Cembre HT81-U hydraulic crimping tools feature built-in safety valves which by-pass the oil supply when the maximum pressure is reached.
The HT 81-U hydraulic crimping tool and RHU 81 hydraulic presshead are lightweight tools for crimping connectors up to 240 mm2. The HT 81-U features a patented die locking pin and can crimp a wide range of connectors with interchangeable dies. The RHU 81 connects to a hydraulic pump and is suitable for crimping in confined spaces. Both tools come with storage cases and feature double speed crimping action for rapid crimping of connectors.
This document provides specifications for the RCO40 wire rope cutter. The cutter can cut steel wire ropes up to 38mm in diameter with a maximum tensile strength of 1960N/mm2. It is designed for cutting wire ropes, cables, and umbilicals under heavy working conditions. The cutter has a stainless steel body and alloy steel cylinder that provide corrosion resistance and a long life for the cutting blade and anvil.
The Macron Single Rail Screw Table can be customized with travel lengths up to 48 inches and load capacities suitable for specific applications. It uses a NEMA 23 motor as standard, with other motor sizes available. Repeatability is +/- 0.005 inches per 36 inches of travel as a maximum. Shipping weights vary depending on the length of travel. The table is supplied with mounting holes and references an 80x40mm extrusion for dimensions.
This document provides specifications for the RCO40LP wire rope cutter, including its cutting capacity of steel wire ropes up to 38mm in diameter with a maximum tensile strength of 1960N/mm2. The cutter is suitable for cutting wire ropes, cables, and umbilicals with a stainless steel body and corrosion resistant materials that provide long life. It also has an open design that allows for easy positioning on cables and can be used at any water depth.
CS Unitec Portable Magnetic Drills: MDM-40CS Unitec
This document provides information about the MDM-40 portable magnetic drill. It can drill holes up to 1-1/2 inches in diameter and features a powerful 9.25 amp motor, compact 13 inch height, and lightweight 24 pound design. It has integrated cutting oil reservoirs and automatic internal lubrication. The magnetic base provides strong holding power of 2,640 pounds on a 1 inch thick plate. It is designed for continuous use with intelligent electronic torque control. Standard equipment includes the drill, pilot pin, shipping case, safety chain, hex key, manual, and warranty.
Oil Field Supplies is an engineering and management consulting firm with 7 years of experience in the OCTG industry. They specialize in manufacturing and trading casing, tubing, drill pipe, and various thread protectors made from pressed steel, plastic, composite materials, and cast steel. Their goal is to provide quality OCTG products at cost effective prices and ensure customer satisfaction.
Measurement solutions for steel mill industryAMETEK STC
Measurement Solutions for the Steel Mill Industry is providing simple and informative overview of the process and the ideal measurement instrumentation. We cover linear position (LDT), Rotary position, brakes, level measurement, pressure measurement and the mill-duty cable and hose carriers Catrac as well. Read the brochure for inspiration to the optimal solutions in steel mill or similar heavy industry
CS Unitec's Catalog of Surface Finishing Tools and AccessoriesCS Unitec
CS Unitec's surface finishing tools and accessories offer professional power tools and abrasive accessories for surface finishing on steel, stainless steel, aluminum and other metals, as well as rigid plastics and wood.
CS Unitec Complete Magnetic Drill CatalogCS Unitec
CS Unitec's portable magnetic drills are idea for drilling structural steel and virtually any metal and are heavy-duty for use in construction and industry.
CS Unitec's core drill is a power tool for boring holes through concrete, reinforced concrete, brick, block, stone and masonry. Specialized core bits - hollow steel cylinders fitted with segmented diamond teeth - grind away the surface to create a hole.
CS Unitec Portable Magnetic Drills & AccessoriesCS Unitec
This document provides information on portable magnetic drilling machines made by CS Unitec. It describes the features and specifications of their line of portable magnetic drills, including electric, pneumatic, and hydraulic models. The drills are designed for continuous operation and drilling of structural steel and metal. They offer variable speed controls, quick-change tool holders, and safety features like overheating protection and electronic shutoff sensors.
CS Unitec Portable Magnetic Drilling MachineCS Unitec
The document provides information about portable magnetic drilling machines made by CS Unitec. It summarizes the key features of their line of magnetic drills including the maximum annular cutter, twist drill, and tapping diameters for each model. It also lists other specifications like stroke, weight, speed ranges, cooling features, and magnet sizes. Accessories and consumables like cutters, lubricants, and vacuum plates are also described. The document promotes CS Unitec as the industry leader in power-to-weight ratios and magnetic drilling strength and touts the reliability and customization of their machines.
This document provides information on Corner Drills and Drives from CSU Nitec, including:
1) Pneumatic and hydraulic corner drills and drives for drilling, reaming, and driving in tight spaces with self-closing throttles and built-in oilers.
2) Slow-speed, high-torque straight drive units that are ideal for heavy-duty reaming, tube expanding, and tapping applications.
3) Technical specifications for pneumatic corner drills, hydraulic corner drills, and pneumatic drive units including torque output, speed, power requirements, and dimensions.
CS Unitec AutoMAB1500 Portable Magnetic DrillCS Unitec
The AutoMAB 1500 is a heavy-duty, compact magnetic drill that automatically controls drill pressure and feed rate for optimal drilling performance. It has a powerful 10.5 amp motor and can drill holes up to 1-1/2 inches in diameter. The drill is portable, lightweight, and ideal for contractors, fabricators, and maintenance professionals. It comes with standard equipment like a carrying case, safety gear, and annular cutters.
Annular cutters can drill burr-free holes without predrilling or stepdrilling. They have precision-ground flutes for efficient chip clearance and hardened tool steel. This increases drilling productivity and reduces tool breakage compared to twist drills.
CS Unitec offers a complete line of High-Quality Non-Sparking, Non-Magnetic and Corrosion-Resistant Safety Tools. CS Unitec is a leader in special Copper Alloy Safety Hand Tools manufactured for use in high-risk areas where a spark can create a disaster.
This document is a parts list for CS UNITEC air motors and geared motors. It contains 52 numbered parts with descriptions and item numbers. It provides contact information for CS UNITEC, including their website and email for inquiries. The parts list contains components for the motor housing, gears, bearings, seals and other internal pieces of the air and geared motors. Prices are subject to change without notice.
This document is a parts list for a CS 3400 P pneumatic nibbler. It contains 30 items including descriptions, item numbers, and parts such as the housing, dies, punches, handles, seals, and valves that make up the nibbler. The list provides the key components and replacement parts for the Model CS 3400 P pneumatic nibbler.
This document is a spare parts list for a Hydraulic Nut Runner Model 3 6242 0010 from CS UNITEC, INC. It contains 81 numbered parts with descriptions and item numbers. The list provides replacement parts for the nut runner's gearbox housing, planetary wheels, shafts, bearings, and other internal components.
[OReilly Superstream] Occupy the Space: A grassroots guide to engineering (an...Jason Yip
The typical problem in product engineering is not bad strategy, so much as “no strategy”. This leads to confusion, lack of motivation, and incoherent action. The next time you look for a strategy and find an empty space, instead of waiting for it to be filled, I will show you how to fill it in yourself. If you’re wrong, it forces a correction. If you’re right, it helps create focus. I’ll share how I’ve approached this in the past, both what works and lessons for what didn’t work so well.
How information systems are built or acquired puts information, which is what they should be about, in a secondary place. Our language adapted accordingly, and we no longer talk about information systems but applications. Applications evolved in a way to break data into diverse fragments, tightly coupled with applications and expensive to integrate. The result is technical debt, which is re-paid by taking even bigger "loans", resulting in an ever-increasing technical debt. Software engineering and procurement practices work in sync with market forces to maintain this trend. This talk demonstrates how natural this situation is. The question is: can something be done to reverse the trend?
HCL Notes and Domino License Cost Reduction in the World of DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdfChart Kalyan
A Mix Chart displays historical data of numbers in a graphical or tabular form. The Kalyan Rajdhani Mix Chart specifically shows the results of a sequence of numbers over different periods.
AppSec PNW: Android and iOS Application Security with MobSFAjin Abraham
Mobile Security Framework - MobSF is a free and open source automated mobile application security testing environment designed to help security engineers, researchers, developers, and penetration testers to identify security vulnerabilities, malicious behaviours and privacy concerns in mobile applications using static and dynamic analysis. It supports all the popular mobile application binaries and source code formats built for Android and iOS devices. In addition to automated security assessment, it also offers an interactive testing environment to build and execute scenario based test/fuzz cases against the application.
This talk covers:
Using MobSF for static analysis of mobile applications.
Interactive dynamic security assessment of Android and iOS applications.
Solving Mobile app CTF challenges.
Reverse engineering and runtime analysis of Mobile malware.
How to shift left and integrate MobSF/mobsfscan SAST and DAST in your build pipeline.
Essentials of Automations: Exploring Attributes & Automation ParametersSafe Software
Building automations in FME Flow can save time, money, and help businesses scale by eliminating data silos and providing data to stakeholders in real-time. One essential component to orchestrating complex automations is the use of attributes & automation parameters (both formerly known as “keys”). In fact, it’s unlikely you’ll ever build an Automation without using these components, but what exactly are they?
Attributes & automation parameters enable the automation author to pass data values from one automation component to the next. During this webinar, our FME Flow Specialists will cover leveraging the three types of these output attributes & parameters in FME Flow: Event, Custom, and Automation. As a bonus, they’ll also be making use of the Split-Merge Block functionality.
You’ll leave this webinar with a better understanding of how to maximize the potential of automations by making use of attributes & automation parameters, with the ultimate goal of setting your enterprise integration workflows up on autopilot.
Your One-Stop Shop for Python Success: Top 10 US Python Development Providersakankshawande
Simplify your search for a reliable Python development partner! This list presents the top 10 trusted US providers offering comprehensive Python development services, ensuring your project's success from conception to completion.
In the realm of cybersecurity, offensive security practices act as a critical shield. By simulating real-world attacks in a controlled environment, these techniques expose vulnerabilities before malicious actors can exploit them. This proactive approach allows manufacturers to identify and fix weaknesses, significantly enhancing system security.
This presentation delves into the development of a system designed to mimic Galileo's Open Service signal using software-defined radio (SDR) technology. We'll begin with a foundational overview of both Global Navigation Satellite Systems (GNSS) and the intricacies of digital signal processing.
The presentation culminates in a live demonstration. We'll showcase the manipulation of Galileo's Open Service pilot signal, simulating an attack on various software and hardware systems. This practical demonstration serves to highlight the potential consequences of unaddressed vulnerabilities, emphasizing the importance of offensive security practices in safeguarding critical infrastructure.
Freshworks Rethinks NoSQL for Rapid Scaling & Cost-EfficiencyScyllaDB
Freshworks creates AI-boosted business software that helps employees work more efficiently and effectively. Managing data across multiple RDBMS and NoSQL databases was already a challenge at their current scale. To prepare for 10X growth, they knew it was time to rethink their database strategy. Learn how they architected a solution that would simplify scaling while keeping costs under control.
Introduction of Cybersecurity with OSS at Code Europe 2024Hiroshi SHIBATA
I develop the Ruby programming language, RubyGems, and Bundler, which are package managers for Ruby. Today, I will introduce how to enhance the security of your application using open-source software (OSS) examples from Ruby and RubyGems.
The first topic is CVE (Common Vulnerabilities and Exposures). I have published CVEs many times. But what exactly is a CVE? I'll provide a basic understanding of CVEs and explain how to detect and handle vulnerabilities in OSS.
Next, let's discuss package managers. Package managers play a critical role in the OSS ecosystem. I'll explain how to manage library dependencies in your application.
I'll share insights into how the Ruby and RubyGems core team works to keep our ecosystem safe. By the end of this talk, you'll have a better understanding of how to safeguard your code.
Main news related to the CCS TSI 2023 (2023/1695)Jakub Marek
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
"Choosing proper type of scaling", Olena SyrotaFwdays
Imagine an IoT processing system that is already quite mature and production-ready and for which client coverage is growing and scaling and performance aspects are life and death questions. The system has Redis, MongoDB, and stream processing based on ksqldb. In this talk, firstly, we will analyze scaling approaches and then select the proper ones for our system.
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Discover top-tier mobile app development services, offering innovative solutions for iOS and Android. Enhance your business with custom, user-friendly mobile applications.
Fueling AI with Great Data with Airbyte WebinarZilliz
This talk will focus on how to collect data from a variety of sources, leveraging this data for RAG and other GenAI use cases, and finally charting your course to productionalization.
1. Portable Hacksaws for Tough Duty
On-site cutting of pipe up to 24" OD and structural steel
Pneumatic • Electric • Hydraulic
PORTABLE HACKSAWS
CS Unitec's power hacksaws offer a wide range
of options for portable cutting of pipe, structural
steel, tanks and other materials. Our saws are
designed for the toughest service in refineries,
power plants, utilities, offshore oil, construction
and demolition applications and are ideal for
shutdowns and turnarounds in process piping
industries. CS Unitec's pneumatic saws are
safer than cutting with a welding torch in
hazardous areas or confined spaces.
• Compact size, ideal for cutting in confined spaces
• 2 3/8" blade stroke
• Pipe clamps for 90˚ cutting of up to 24" OD pipe
• Profile clamps for structural steel
• Wide variety of blades and accessories for
cutting steel, stainless steel, aluminum, plastic,
wood and ductile iron
• Optional blade guide to ensure right-angle cuts
• Automatically cut pipe with our optional self-
feeding, pneumatic-powered pipe clamp system
Assorted pipe clamps for
pipes up to 24" OD or profile
clamps for structural steel Twist or lever throttle
(see page 17)
Manual or Pneumatic, electric
automatic feed or hydraulic motor
Pneumatic:
Heavy-duty saw 3/4" NPT Connection
blades from 8" to Electric:
37" long 110 Volt (220V available)
Hydraulic:
1/2" FF (HTMA) Couplings
HSS, HSS-SL,
carbide-coated Optional saw blade guide
and Diamond- for added blade stability –
coated ensures straight cutting!
blades Two sizes available
available (Not required – see page 18)
(see page 19)
14 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
2. Portable Pneumatic Power Hacksaws
Pneumatic power for hazardous environments
Model 5 1212 0050 • Pneumatic motor with variable speeds
with lever throttle
• Ideal for cutting pipe, tanks, structural
PORTABLE HACKSAWS
Pneumatic
steel, profiles and other materials
• Designed for the toughest service in
refineries, chemical plants, utilities,
pipelines,
ATEX Certified
construction, Pipe Capacity
3/4" NPT Air Connection offshore oil and 24" OD
ATEX Certified for Ex Zone EX II 2 GcT5 demolition
applications Profile Capacity
• Cut pipe up to 24" 21 3/4" h x 11 1/2" w
Throttle Types for Pneumatic Saws:
OD in one pass
Roll Throttle
(air model 5 1212 0010 only) – • Chain clamps and profile clamps
used only with automatic feed available for accurate 90˚ cutting of
pipe clamp (see page 18)
pipe and structural steel
Lever Throttle
(model 5 1212 0050) – provides • 2 3/8" stroke for heavy-duty cutting
on/off paddle switch for manual • Ideal for cutting in confined spaces
cutting with clamp
• Accommodate heavy-duty blades up
to 37" long
• Optional saw blade guides to increase
Clamps blade stability (see page 18)
Manual Automatic • Pneumatic pipe clamp system
available for automatically cutting
pipe; easily attaches to pneumatic
hacksaw and shares same air supply
(see accessory No. 5 1208 9980 on
page 18)
Accessory Saw Blades
Clamps for Pipes and Profiles – manual and (see page 19)
automatic-feed clamps for straight, 90˚ cutting
of pipes and profiles (see pages 17-18)
• HSS (High-speed Steel), HSS-SL (for
stainless steel and hard metal), Carbide
Coated and Diamond Coated
Model Strokes Blade Weight
Power Throttle Motor Specifications Hose
No. per Min. Stroke (lbs.)
Pneumatic - 3/4" ID NPT Air Connection
5 1212 0010 1.5 HP Roll Air Consumption: 51 CFM 100-350 2 3/8" 1/2" ID 15.4
5 1212 0050 1.5 HP Lever Air Pressure: 90 PSI 100-350 2 3/8" 1/2" ID 15.4
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 15
3. Portable Power Hacksaws
Electric and hydraulic power
• Electric or hydraulic motor with variable speeds
Model 5 1215 0070
with variable speed • Ideal for cutting pipe, tanks, structural steel,
PORTABLE HACKSAWS
Electric profiles and other materials
• Designed for the toughest Pipe Capacity
service in refineries, chemical
24" OD
plants, utilities, pipelines,
construction, offshore oil and Profile Capacity
demolition applications 21 3/4" h x 11 1/2" w
11 Amps / 110 Volt (220 Volt Available) • Cut pipe up to 24" OD in one
pass
• Chain clamps and profile clamps available for
Model 5 1220 0050 accurate 90˚ cutting of pipe and structural steel
with lever throttle
Hydraulic • 2 3/8" stroke for heavy-duty cutting
• Ideal for cutting in confined spaces
• Accommodate heavy-duty blades up to 37" long
• Optional saw blade guides to increase
blade stability (see page 18)
1/2" FF Couplings • Automatic-feed pipe clamp system available
for automatically cutting pipe – saves operator
time and makes work easier
(see accessory No. 5 1208 9990 on page 18)
Clamps
Accessory Manual Automatic
Saw Blades
(see page 19)
• HSS (High-speed Steel), HSS-SL
(for stainless steel and hard metal),
Carbide Coated and Diamond Coated
Clamps for Pipes and Profiles – manual and
automatic-feed clamps for straight, 90˚ cutting
of pipes and profiles (see pages 17-18)
Model Strokes Blade Weight
Power Throttle Motor Specifications Hose
No. per Min. Stroke (lbs.)
Electric - 11 Amps / 110 Volt**
5 1215 0070* 1.5 HP Trigger 110V/60 Hz (220V/50Hz is available) 200-400 2 3/8" Cable 13
Hydraulic - 1/2" FF (HTMA) Couplings
5 1220 0050 3.8 HP Lever Oil Flow: 4 GPM at 2000 PSI 100-500 2 3/8" 1/2" ID 13.5
* Model 5 1215 0070 has an electronic speed control dial. **Also available as 220 Volt/50 Hz
16 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
4. Hacksaw Accessories
Heavy-duty cutting of pipe and structural steel
Clamps for Pipes and Profiles
Ensure 90˚ cuts through pipe and profiles
HACKSAW ACCESSORIES
Large Pipe Clamp with lever Model No. 5 1207 9910
lock for no-tools tightening, 2" to 6" OD pipe clamp
Model 5 1202 9950 (below)
Model No. 5 1202 9950
4" to 12 3/4" OD pipe clamp –
lever lock provides no-tools
tightening of chain (up to Small Pipe Clamp,
24" OD with extension chain Model 5 1207 9910
shown below)
Model No. 5 1202 9960
4" to 12 3/4" OD pipe clamp –
manual tightening of chain Up to 6"
(up to 24" OD with extension pipe dia.
Large Pipe Clamp, chain shown below)
Model 5 1202 9960
Profile Clamp,
Lever Lock Assembly Model 5 1207 8970
Part No. 5 1202 9970
Model No. 5 1207 8970
Can be used to retrofit 21 5/8" x 11 3/8" profile
manual clamp 5 1202 9960
for no-tools tightening of clamp
chain. Also fits similar clamps.
Extension Chains for Pipe Clamps
• Extend capacity of pipe clamps up to 24" OD
Model No. 5 1201 9010 – 17 3/4" chain extension
Model No. 5 1201 9030 – 39 3/8" chain extension
(allows pipe clamp Nos. 5 1202 9960 and 5 1208 9940 to fit 24" OD pipe)
Clamps for Pipes and Profiles
Model No. CP1 – Universal Clamp
• Self-aligning feet adjust to the form of the
workpiece (round, square and angled)
• Accommodates 1/2" to 12 3/4" OD [up to 24" OD
with extension chain no. CP1/10 (393/8" long)]
• CP1 easily attaches to most of our
reciprocating saws for 90˚ cuts in tight spaces
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 17
5. Hacksaw Accessories
Automatic feed pipe clamps save time and effort
Self-feeding Pipe Clamp for Pneumatic Saws
HACKSAW ACCESSORIES
Air-Powered Model No. 5 1208 9980 – Automatic Clamp
Clamp • Save time and effort by automatically cutting
pipe up to 12 3/4" OD (up to 24" OD with
extension chain – see page 17)
• Self-feeding device saves
operator time, increases
safety and makes
work easier
• Easily attaches to CS Unitec air hacksaw
and shares same 90 PSI air supply (Pipe
clamp for use only with CS Unitec air
hacksaw Model No. 5 1212 0010)
• Blade guide for straight cutting through
pipe and difficult materials is optional
(see below)
Self-feeding Pipe Clamp for Electric and Hydraulic Saws
Model No. 5 1208 9990 – Automatic Clamp
Self-Feeding
Mechanical • Save time and effort by automatically cutting pipe up to
Clamp 12 3/4" OD (up to 24" OD with
extension chain – see page 17)
• Self-contained gas cylinder
provides constant feed pressure to
saw blade
• Saves operator time, increases
safety and makes work easier
• Easily attaches to CS Unitec
electric hacksaw 5 1215 0070 or
hydraulic hacksaw 5 1220 0050
• Optional blade guide for straight
cutting through pipe and difficult
materials (see below)
Blade Guides
Optional guides with two roller bearings
• Ensure straight cutting through pipe and difficult materials
Model No. 5 1207 9970 for pipes up to 13" (20" min. blade length required)
Model No. 5 1207 8910 for pipes up to 21" (30" min. blade length required)
18 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
6. Hacksaw Blades - 8" up to 37" long
Heavy-duty cutting of pipe and structural steel
HACKSAW BLADES
Extra thick for 90˚ cutting
HSS or HSS-SL Saw Blade Shown *Use HSS-SL Blades for best cutting
performance on stainless steel and hard metal.
Use ProLube™ Specialty Lubricants with Hacksaw Blades to help tools work cooler, longer and more efficiently.
ProLube Lubricants are non-toxic and ideal for stainless steel and hard metal cutting applications. See page 34.
Dimensions Steel and Plastic Ductile/Cast Iron Max. Dia.
Order No.
Length Teeth/Inch Thickness Nonferrous Metal and Wood and Masonry of Cut
Z22-9 HSS 8" 8 1/16" Steel/Aluminum Plastics – 31/8"
Z22-10 HSS 8" 16 1/16" Steel – – 31/8"
Z22-11 HSS 8" 24 1/16" Sheet Metal – – 31/8"
Z22-6 HSS 12" 16 1/16" Steel – – 65/8"
Z22-6 HSS-SL* 12" 16 1/16" Stainless Steel – – 65/8"
Z22-6 Carbide 12" Coated 3/16" – – Masonry 65/8"
Z22-31 HSS 12" 12 1/16" Steel – – 65/8"
Z22-71 HSS 12" 4 1/16" – Plastics/Wood – 65/8"
Z22-83 TDS 12" Coated 3/32" – – Ductile Iron 65/8"
Z22-7 HSS 16" 16 1/16" Steel – – 105/8"
Z22-7 Carbide 16" 16 1/16" – – Masonry 105/8"
Z22-29 HSS 16" 8 1/16" Steel/Aluminum Plastics – 105/8"
Z22-32 HSS 16" 4 1/16" – Plastics/Wood – 105/8"
Z22-33 HSS 16" 6 1/16" Cast Iron Plastics Cast Iron 105/8"
Z22-86 TDS 19" Coated 7/64" – – Ductile Iron 13"
Z22-72 HSS 20" 14 5/64" Steel – – 145/8"
Z22-72 Carbide 20" Coated 3/16" – – Masonry 145/8"
Z22-30 HSS 21" 12 1/16" Steel – – 155/8"
Z22-30 HSS-SL* 21" 12 1/16" Stainless Steel – – 155/8"
Z22-40 HSS 21" 4 1/16" – Plastics/Wood – 155/8"
Z22-73 HSS 24" 14 5/64" Steel – – 181/2"
Z22-73 Carbide 24" Coated 3/16" – – Masonry 181/2"
Z22-74 HSS 24" 8 5/64" Steel/Aluminum Plastic – 181/2"
Z22-75 HSS 30" 12 5/64" Steel – – 247/8"
Z22-75 HSS-SL* 30" 12 5/64" Stainless Steel – – 247/8"
Z22-76 HSS 30" 6 5/64" Plastics/Wood 247/8"
– –
Z22-37 HSS 37" 12 5/64" Steel 317/8"
– –
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 19