Clifford & Snell - Yodac V4 Beacon, Hazardous Area ATEX Zone 1 & 2 Beacons (Flashing)

•

0 likes•1,198 views

This document summarizes an intrinsically safe LED status beacon that is: 1) BASEEFA (ATEX) approved for use in hazardous zones, with up to 4 modules in combinations of lens colors like red, amber, green, opal, blue, or clear. 2) Rated for continuous use with high light intensity and a long life LED design. 3) Simple to install with a reliable, flame retardant ABS plastic enclosure that is also anti-static.

Technology

• BASEEFA (ATEX) approved
• 8 LED array allowing condition or status alert in ‘on or off ’ mode
• Continuously rated
• High light intensity
• Long life LED design
• Reliable and simple to install
• Red / White flame retardant ABS plastic enclosure
• Anti static enclosure and lens
• Up to 4 modules in any combination of lens colour ranging from
Red, Amber, Green, Opal, Blue, Clear
• Each beacon should be wired independently.
TECHNICAL SPECIFICATIONDIMENSIONS mm
MAIN FEATURES
Controlled document No. D7472-01-02 (CN100301) My DocumentsSALES DATAdata sheetsYodac
MOUNTING
All units are supplied separate from the back box for ease of
installation. The back box should be mounted to a reasonably flat
surface or bulkhead. A gasket is supplied, should the surface be
uneven, or if the unit is to be used in wet conditions.
The installation is completed by fitting the beacon onto the back box
by means of the supplied screws.
LINE MONITORING
Monitoring via reverse polarity
End of line resistor minimum 3K3 ohms 0.5 watts wire-wound or
metal film type
CONFIGURATOR
Unit Type
V4 LED Intrinsically Safe
‘Status’ Beacon
Supply Voltage
AmberRed
Lens Colours
Base Colours
White
Red Flame
ORDERING INFORMATION
Base Colours:
RF = Red flame
WN = White
RN = Red Normal
C l i f f o r d & S n e l l
Clifford & Snell a division of Signature Industries Ltd part of the Digital Angel Corporation
Intrinsically Safe LED ‘Status’ Beacons
• For use in Zones 0, 1 and 2
• Operating voltage 12Vdc, 18Vdc, 24Vdc via ATEX
approved barriers
• Operating temp range –20 to + 40deg C
• Storage temp range –40 to + 70deg C
• Relative humidity 90% @ 40deg C
• IP65 rated
• Weight: Single 0.15 Kg, Double 0.3 Kg, Triple 0.45 Kg, Quad
0.6 Kg
• EEx ia IIC T4
APPROVAL SPECIFICATION
ATEX DIRECTIVE - 9/94/EC
EN60079-0:2004 (EN50014:1997 + Amendments 1 & 2)
EN60079-1:2004 (EN50020:2002) EN50284:1999
Baseefa certificate No. BAS05ATEX0075
12, 18 & 24Vdc Via
ATEX approved barriers
Tom Cribb Road, Thamesmead,
London SE28 0BH
Tel: +44 (0)20 8316 4477
or (0)20 8317 1717
Fax: +44 (0)20 8317 2400
Email: sales@cliffordandsnell.com
Web Site: www.cliffordandsnell.com
Intrinsically Safe
‘Status’ Beacons
2nd
3rd
4th
1st
90 (3.5”)
90 (3.5”)
90 (3.5”)
90 (3.5”)
90 (3.5”)
Green Opal Blue Clear
1st
2nd
3rd
4th
1st 1st
2nd 2nd
1st
3rd
Depth = 81 (3.2”)
Single
Double
Triple
Quad
All dimensions quoted are approximate only and subject
to change without notice as are technical features resulting
from continual development and improvement.
Number of Modules (leave blank if single unit)
or 2,3 or 4
Single
Triple
Quadruple
Double
X
ATEX
Yodac
Red Normal
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK

Clifford & Snell is a UK-based company established in 1929 that specializes in audible and visual signaling equipment. The document provides information on Clifford & Snell's product range, which includes explosion proof sounders, strobes, and call point stations approved for hazardous and industrial applications. It also lists specifications for the company's Yodalex line of products and provides a product index with descriptions, types, and approvals for its sounders, strobes, and accessories.

Clifford & Snell - Yodalex YO9 - Hazardous Area (ATEX) Sounder

Thorne & Derrick International

The document provides specifications for the Yodalex explosion proof sounder including: - It has a sound output of 115dB at 1 meter and is IP66 and NEMA 4X rated for outdoor or indoor use. - The sounder is approved for use in gas and dust hazardous areas and is evaluated for marine use. - It has adjustable settings for tone, voltage, and bracket mounting and provides monitoring and alarm functions.

Clifford & Snell - Manual Call Point, Hazardous Area (ATEX) - Yodalex MCP

Thorne & Derrick International

This document provides specifications for manual call point stations made by Clifford & Snell, including: - Technical specifications for light weight GRP enclosures with glass or push button activation, monitoring capability, and weather resistant paint. - Dimensions of 132.5mm x 74mm x 98mm and approvals to ATEX, IECEx, and BS EN 54-11 standards for use in hazardous zones. - Options include LED indicators, labels, cable entries, finishes, switches, and end of line or in line resistors.

Clifford & Snell - Yodalex V6 - Hazardous Area ATEX Sounders (Horns) & Beacon...

Thorne & Derrick International

This document provides specifications for Clifford & Snell explosion proof sounders and beacons. The devices have omnidirectional high output sound, independently selectable 2-stage alarms, and share an explosion proof housing. They are approved by various standards including UL, CSA, ATEX, and IECEx. The sounders and beacons come in various voltage options and have IP66/NEMA 4X protection. Dimensions and current draw requirements are provided for the different models.

Clifford & Snell - YL4 Sounder - Hazardous Area (ATEX) Zone 1 & Zone 2

Thorne & Derrick International

This document provides specifications for intrinsically safe audible and visual alarms produced by Clifford & Snell. It includes details on: - Models of sounders and beacons that meet ATEX certification and UKOOA standards for use in hazardous zones - Technical specifications on operating voltages, temperatures, weights, sound outputs, and IP ratings - Dimensional drawings and mounting information for the different models - Recommended European approved barriers for use with the units - References for additional operating and installation instructions

Walsall - Hazardous Area ATEX Manual Call Points & Breakglass Units Zone 1 & ...

Thorne & Derrick International

Walsall Equipment is a British manufacturer of electrical equipment for hazardous, wet, and dusty environments. It has offices worldwide including Europe, Asia, Africa, and Australia. The company produces a wide range of ATEX-approved products for zone 1, 2, 21, and 22 applications, including junction boxes, lighting, control stations, and cable management systems. It has a purpose-built manufacturing facility with advanced equipment and invests heavily in new technology and product development.

MEDC Manual Call Points & Break Glass Units for Hazardous Areas

Thorne & Derrick International

This document provides specifications for manual call points used in fire alarm systems. It describes two models - breakglass and pushbutton - that are available in various protection levels including weatherproof, explosion protected, and intrinsically safe versions. Key features outlined include the polyester enclosure, operating elements, certification approvals, terminal and cable entry options, electrical ratings, and ordering requirements with a coding system.

Aluminium Control Panels - Walsall ASMCP/AL EEx d Control Panels

Thorne & Derrick International

This document provides information on electrical equipment for hazardous environments made by Walsall Ltd. It includes terminal enclosures, local control panels, distribution boards, lighting, and other equipment certified for use in explosive atmospheres. The company was founded in 1892 and originally manufactured bangles and metalwork, later expanding into electrical equipment. It offers a wide range of explosion proof products made from materials like stainless steel, aluminum, and GRP.

This document provides information on EFQL Miniature Automatic Circuit Breakers. It summarizes that the breakers are made of copper-free aluminum and painted according to RAL 6003. They can be used indoors or outdoors in hazardous locations. The document also lists control units that consist of explosion-proof enclosures completed with automatic circuit breakers, on-load switches, and selector switches up to 63A. It provides specifications on material, IP ratings, temperature range, certifications, standards, explosion-proof codes, surface treatment, entries, poles, voltage, and accessories.

Marechal SPeX ATEX Plug & Socket Power Connector - Zones 1, 2 21, 22

Thorne & Derrick International

Marechal SPeX Single Pole Power Connector Zone 1 & Zone 2 Zone 21, Zone 22 680 Amp IP65/IP66 Water & Dust-tight Marechal Hazardous Area Plugs & Sockets 1000V a.c. / 1500V d.c. single pole, 6800A ‘e' increased safety Marechal SPeX plug and socket power connector enables the user to connect and disconnect heavy duty equipment simply and safely in hazardous area zones 1, 2, 21 and 22. Designed for use in hazardous areas the Marechal SPeX plug and socket assembly is ATEX 94/9/CE approved for zones 1 & 2 (gas) and zones 21 & 22 (dust). Marechal SPeX offers automatic IP66/IP67 ingress protection rating as soon as the plug is inserted into the socket. Electromechanical interlocking is provided via a microswitch (which opens and closes all phases simultaneously) to protect the user and to prevent electrical destabilisation of equipment. The Marechal casing is manufactured in glassfibre-reinforced polyester which affords excellent mechanical protection (IK08) and resistance to UV and chemical agents. Typical applications include mobile gensets, ship-to-shore supplies, mines, offshore platforms etc. The incorrect mating of phases is mechanically impossible. Furthermore colour-coding enables a visual check. Marechal SPeX Single Pole Power Connector Marechal SPeX - EX ATEX Hazardous Area Plug, Socket Power Connector Enhanced protection mode « e » Compliant with ATEX 94/9/CE Directive Zones 1 and 2 (gas) and zones 21 and 22 (dust) Up to 680 A Up to 1000 V a.c. Interlock switch system via pilot contacts, synchronized connection and disconnection for all phasesMechanical keying system with 5 positions to discriminate between phases Visual identification of phases with standard colour codes Automatically IP65 dust and watertight IK08 shock resistant GRP casings Resistant to temperature changes: -40 °C to +60 °C

JAREL EXPORT

Paul Richardson

This document provides information on electrical products and services from Jarel Export for hazardous areas. It describes Jarel Export's specialization in hazardous area electrical products including lighting, control systems, power distribution, motor starters, and other equipment. Technical specifications and certifications are provided for several example products like bolted sockets, cable glands, luminaires, and motors.

ABB ATEX Industrial Plugs & Sockets - Hazardous Area Plugs & Sockets

Thorne & Derrick International

This document provides information on industrial plugs and sockets for use in explosive atmospheres that comply with ATEX directives. It defines ATEX as "ATmospheres EXplosive" and describes the European directives and standards regarding equipment used in explosive environments. The document outlines explosion zones and categories of equipment intended for different zones. It provides details on product labeling requirements and declarations of conformity. Product information and ordering codes are listed for various plug and socket options.

Stahl YA90 Sounder Signalling Device – ATEX Zone 1 Zone 2 Hazardous Area Sign...

Thorne & Derrick International

Zone 1 (ATEX) Bulkhead Fluorescent Fire Exit Luminaire - HDL108, (32 Watts)

Thorne & Derrick International

This document provides specifications for the Hadar Lighting HDL 108 bulkhead luminaire. It is designed for use in hazardous areas and includes two 18W compact fluorescent lamps, a steel or stainless steel enclosure, prismatic glass diffuser, and silicone gasket. It has a T3/T4 temperature rating and IP64 ingress protection. The luminaire can be surface or recessed mounted, with cable entries on any face or rear, and is available as a standard or emergency light.

Marechal DSN Compact & Watertight Decontactors - Industrial Plugs & Sockets I...

Thorne & Derrick International

Floodlights Zone 1 & Zone 2 (ATEX) - Hadar Hazardous Area Lighting

Thorne & Derrick International

The document provides information on lighting products from Hadar Lighting, including: - A range of luminaires suitable for hazardous areas certified for Zone 1 and Zone 2, incorporating the latest technologies. - Product lines include fluorescent, recessed, portable, bulkhead, wellglass, and LED luminaires. - Detailed specifications, dimensions, ordering information, and installation guidelines are provided for various luminaire models.

Wolf Safety Lamp - Zone 1 Hazardous Area Tank Lighting Kit (ATEX Certified)

Thorne & Derrick International

Tank Lighting - Wolf Hazardous Area Portable Lighting. Wolf Safety’s Zone 1 Hazardous Area Tank Lighting Kit, CE marked for ATEX compliance, provides a quick and easy portable temporary lighting solution in Zone 1 hazardous areas. The Tank Lighting Kit comprises a Zone 1, 230V or 110V to 24V Ex transformer supplying extra low voltage for use in tanks and vessels and four LL-500 fluorescent leadlamps, with either twin or quad lamp configuration. Each Wolf lamp is supplied with 20m SY cable and fitted with hazardous area ATX 2P+E plugs and sockets for connection in the explosive area, ATEX certified.

Zone 1 Floodlight (Ex de) Hazardous Area - Hadar HDL117 500 Watt Lamps

Thorne & Derrick International

This document provides specifications for the HDL 117 floodlight made by Hadar Lighting. Key features include various wattage discharge and halogen lamps from 150W to 500W, simple installation and maintenance, and a marine grade aluminum and stainless steel body. Electrical specifications include voltage ranges from 110V to 240V at 50/60Hz and Ex e certification for use in hazardous zones. An ordering matrix and installation instructions are also included.

Motor Starters - DOL Direct on Line ATEX 5.5KW - Walsall DOL5.5

Thorne & Derrick International

This document provides information on electrical equipment for hazardous environments made by Walsall Ltd. It includes terminal enclosures, junction boxes, local control panels, and other equipment. The company was founded in 1892 and began making electrical equipment for hazardous areas in the 1920s. It now offers a wide range of explosion proof certified equipment for use in zones 1, 2, 21, and 22.

Rotronic HygroFlex5-EX - HF5-EX Hazardous Area Humidity & Temperature Sensors...

Thorne & Derrick UK

This document describes intrinsically safe humidity and temperature transmitters for use in explosive atmospheres. The transmitters measure relative humidity and temperature with optional outputs for dew point and other calculated parameters. They have an intrinsically safe electrical construction allowing operation in areas with explosion risk without an intrinsically safe power supply. Interchangeable probes made of stainless steel can be used with a robust aluminum transmitter housing.

Zone 1 (ATEX) Recessed Luminaires Hadar HDL102 - (Twin 18 Watts)

Thorne & Derrick International

The document provides specifications for the HDL 102 recessed luminaire from Hadar Lighting. It can be installed in modular or non-modular ceilings and comes in different configurations with 2 or 4 lamps of 18, 36, or 58 watts each. The luminaire has an IP64 rating and is certified for use in hazardous zones. It has options for emergency lighting, different voltages and cable entries, and can be ordered in a configuration code that specifies fittings, voltage, lamps, and other details.

Explosion Proof Cable Glands - Prysmian Barrier Glands (424TP) for Lead Sheat...

Thorne & Derrick International

The document discusses explosion proof cable glands. It describes the Barr-Pb EEx d IIC brass barrier gland, which provides an IP66 seal for lead sheathed cables used in hazardous areas. It can be used in zones 1 and 2, and provides mechanical cable retention, electrical continuity to the armor wire and inner lead sheath. Technical data includes ATEX certification, a service temperature range of -60°C to +90°C, and zones in which it can be used. Tables provide gland details, references, thread sizes, and dimensions.

Zone 1 (ATEX) Bulkhead Fluorescent Fire Exit Luminaire - HDL109 (32 Watts)

Thorne & Derrick International

This document provides information on the HDL 109 bulkhead luminaire from Hadar Lighting. It is a Zone 1 approved explosion-proof bulkhead light fixture intended for use in hazardous locations. It uses 2 x 18W compact fluorescent lamps and has an emergency version. Key features include IP66/67 ingress protection, operating temperatures up to 100°C, mounting options of Unistrut, bracket or pole, and ATEX and IEC Ex certification.

Marechal DXN ATEX Plug & Socket Outlets (Decontactors) for Hazardous Areas Zo...

Thorne & Derrick International

The Marechal DXN Plug and Socket Outlets (decontactors) comply with ATEX Hazardous Area Certification for use in Explosive Atmospheres including Zones 1 and 2 (gas) and Zones 21 and 22 (dust). Marechal DXN ATEX certified hazardous area plugs and sockets are rated from 20-63amps, IP66/67 watertight ingress protection and with socket-outlet safety shutter providing IP4X protection. The Marechal DXN plugs and sockets also comply with EN 50018 (explosion proof safety "d") EN 50019 (increased safety "e"), EN 50281-1-1 (electrical equipment for use in flammable dust atmospheres) and IEC 60309-1 (plugs and socket-outlets for industrial purposes) standards.

Aswich Electrical: ERS Rapid Shut-down Switch(fire safety switch)

Aswich Electrical

Suitable for 3-string，4-string,5-string modules Maximum circuit current 55A Maximum cricuit voltage 1500vdc CE certificated Sheet metal material, IP66 protection grade Multi clock interface type optional (knockout hole / gland / MC4 terminal) The Isolation switches are TUV.CE.CB.SAA certificated Waterproof Vent valve to avoid condensation inside the shell Advanced temperature sensor is used to detect the highest temperature in the shell in real time temperature, when the internal temperature exceeds 70 degrees, automatic cut-off switch It is suitable for residential, industrial and commercial photovoltaic systems contact@aswich.com http://www.aswich.com/

ATEX Hazardous Area Electrical Enclosures, Zone 1 - GRP Enclosure - Petrel G40

Thorne & Derrick International

Petrel G40 range of GRP hazardous area electrical enclosures and terminal boxes are suitable for use in Zone 1 gas and dust environments and can be configured to client specification. Petrel Zone 1 GRP Electrical Enclosures for Hazardous Areas * Graphite loaded material minimises static build up within enclosure * Various standard hazardous area GRP enclosure sizes * GRP enclosures are simple to populate, terminals 2.5-120sqmm * Hazardous area T class ratings, T6 -20°C to +40°C, T5 -20°C to +55°C * IP66 GRP electrical enclosure suitable for Zone 1 hazardous areas Hazardous Area GRP Electrical Enclosures : EEx e dm ia II 2 GD IIC T6 Thorne & Derrick UK are official distributors for the Petrel Hazardous Area & Explosion Proof Electrical Equipment ranges for Zones 1 and Zone 2 installation with ATEX certification - this includes hazardous area lighting (well glass, fluorescent luminaire, bulkhead, floodlight) motor starters, isolators, push button starter units, control stations and electrical enclosures. Cast (aluminium alloy or iron) explosion proof enclosures suitable for use in Zone 1 hazardous area applications. EX Lighting Products from Petrel Hazardous Area Electrical Equipment : Ex de Well Glass, Ex d Emergency Flourescent Luminaire, Ex de Bulkhead, Ex de Zone 1 Floodlight, Zone 2 Floodlight, Ex ed Standard & Emergency Flourescent Luminaire, Zone 2 Standard & Emergency Flourescent Luminaire, Ex d Flourescent Luminaire, Zone 2 Bulkhead Luminaire, Ex ed Recessed Zone 1 Flourescent Luminaire.

Control Stations - Hazardous Area - Technor XAWG-XAWF-XAWFS

Thorne & Derrick International

The document describes control boxes/stations that provide explosion protection for use in hazardous environments. It includes specifications for several standard sizes of enclosures made of stainless steel or GRP. The boxes have IP66 protection, an operating temperature range of -20°C to +60°C, and drainage to prevent water penetration. They are ATEX approved and suitable for offshore, onshore, petrochemical and marine applications where explosive atmospheres may exist.

Hadar Hazardous Area Lighting - HDL102 - Recessed Zone 1

Thorne & Derrick International

The document provides specifications for the HDL 102 recessed luminaire from Hadar Lighting. It can be installed in modular or non-modular ceilings and comes in different sizes to accommodate various lamp configurations like 2x18W or 4x36W fluorescent lamps. The luminaire has an IP64 rating and Zone 1 certification making it suitable for use in hazardous areas where gas and dust may be present. Key features include ease of maintenance, high frequency electronic control gear, and overvoltage protection.

Zone 1 (ATEX) Bulkhead Fluorescent Fire Exit Luminaire - HDL108 (36 Watts)

Thorne & Derrick International

Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson Industrial

Thorne & Derrick International

What's hot

Control Stations - Hazardous Area - Technor EFQL

Thorne & Derrick International

Marechal SPeX ATEX Plug & Socket Power Connector - Zones 1, 2 21, 22

Thorne & Derrick International

JAREL EXPORT

Paul Richardson

ABB ATEX Industrial Plugs & Sockets - Hazardous Area Plugs & Sockets

Thorne & Derrick International

Stahl YA90 Sounder Signalling Device – ATEX Zone 1 Zone 2 Hazardous Area Sign...

Thorne & Derrick International

Zone 1 (ATEX) Bulkhead Fluorescent Fire Exit Luminaire - HDL108, (32 Watts)

Thorne & Derrick International

Marechal DSN Compact & Watertight Decontactors - Industrial Plugs & Sockets I...

Thorne & Derrick International

Floodlights Zone 1 & Zone 2 (ATEX) - Hadar Hazardous Area Lighting

Thorne & Derrick International

Wolf Safety Lamp - Zone 1 Hazardous Area Tank Lighting Kit (ATEX Certified)

Thorne & Derrick International

Zone 1 Floodlight (Ex de) Hazardous Area - Hadar HDL117 500 Watt Lamps

Thorne & Derrick International

Motor Starters - DOL Direct on Line ATEX 5.5KW - Walsall DOL5.5

Thorne & Derrick International

Rotronic HygroFlex5-EX - HF5-EX Hazardous Area Humidity & Temperature Sensors...

Thorne & Derrick UK

Zone 1 (ATEX) Recessed Luminaires Hadar HDL102 - (Twin 18 Watts)

Thorne & Derrick International

Explosion Proof Cable Glands - Prysmian Barrier Glands (424TP) for Lead Sheat...

Thorne & Derrick International

Zone 1 (ATEX) Bulkhead Fluorescent Fire Exit Luminaire - HDL109 (32 Watts)

Thorne & Derrick International

Marechal DXN ATEX Plug & Socket Outlets (Decontactors) for Hazardous Areas Zo...

Thorne & Derrick International

Aswich Electrical: ERS Rapid Shut-down Switch(fire safety switch)

Aswich Electrical

ATEX Hazardous Area Electrical Enclosures, Zone 1 - GRP Enclosure - Petrel G40

Thorne & Derrick International

Control Stations - Hazardous Area - Technor XAWG-XAWF-XAWFS

Thorne & Derrick International

What's hot (19)