Caterpillar Cat 745C Articulated Truck (Prefix LFK) Service Repair Manual (LFK00001 and up).pdf

Service Repair Manual
Models
745C Articulated Truck

Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 745C ARTICULATED TRUCK LFK
Configuration: 745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
735C, 740C EJECTOR and 745C Articulated Trucks Power Train
Media Number -UENR4227-04 Publication Date -01/09/2015 Date Updated -02/07/2018
i06530696
Torque Converter - Install
SMCS - 3101-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5472 Lifting Eye Assembly 2
B FT-3307 Installation Tool 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/4
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine(SE...
2020/1/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g03862127
Note: Note the position of the wiring harness clips.
1. If necessary, remove housing (6).
2. Install Tooling (A) and a suitable lifting device to torque converter (5). The weight of torque
converter (5) is approximately 95 kg (209 lb).
Note: The torque converter needs to make three spline connections and spin freely to be
properly seated.
3. Install torque converter (5) Remove the suitable lifting device and Tooling (A).
2/4
2020/1/2

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

4. Position a new gasket and install housing (6). Install bolts (7) the washers and the clips.
Note: Install a new retaining ring (3) Do not reuse old retaining ring (3).
5. Install plate (4). Install retaining ring (3).
3/4
2020/1/2

6. Using tooling (A), install the O-ring seals onto pilot (2) and install pilot (2). Install retaining
ring (1).
End By:
a. Install the transmission.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 2 10:22:30 UTC+0800 2020
4/4
2020/1/2

Shutdown SIS
Previous Screen
i06668607
Gear Pump (Transmission Scavenge) - Remove and Install
SMCS - 3066-010; 3115-010
Removal Procedure
Start By:
a. Release the system pressure.
b. Install the steering frame lock.
1. Tilt the cab. Refer to the Operations and Maintenance Manual, "Cab - Tilt" for the correct
procedure.
2. Disconnect hose assembly (1) and tube (2).
3. Remove bolts (3) and the washers. Remove transmission pump (4) and the O-ring seal.
1/2
2020/1/2

Shutdown SIS
Previous Screen
i06219270
Transmission Oil Filter - Remove and Install
SMCS - 3067-010
Removal Procedure
Start By:
a. Release the system pressure.
NOTICE
containing fluids.
Cat®
products.
1/3
2020/1/2

1. Removing housing (5) and the O-ring seal. Remove the filter.
2. To remove the transmission oil filter base, complete the following steps.
3. Disconnect three hose assemblies (2). Disconnect harness assemblies (1) and (4).
4. Remove bolts (3) and the oil filter base.
5. Remove harness assembly (6).
1. Install the transmission oil filter in the reverse order of removal.
a. If the transmission oil filter base was removed. Tighten harness assembly (6) to a
torque of 15 ± 3 N·m (133 ± 27 lb in).
b. Tighten housing (5) to a minimum torque of 50 N·m (37 lb ft) to a maximum torque
of 100 N·m (74 lb ft). Tighten housing (5) with 1-1/2 inch socket or box end wrench.
Thu Jan 2 10:24:22 UTC+0800 2020
2/3
2020/1/2

Shutdown SIS
Previous Screen
i06219401
Main Drive Shaft - Remove and Install
SMCS - 3175-010; 3253-010-MV
Removal Procedure
Table 1
Required Tools
A
8S-7610 Base 1
396-9840 Cylinder 1
350-7768 Electric Hydraulic Pump115V
1
350-7769 Electric Hydraulic Pump Gp230V
1
8S-7615 Pin 1
B 155-3597 Wheel Chock 2
Start By:
a. Remove the cooling package.
Personal injury or death can result from improper lifting or blocking.
When a hoist or jack is used to lift any part or component, stand clear of
the area. Be sure the hoist or jack has the correct capacity to lift a
component. Install blocks or stands before performance of any work
under a heavy component.
1/4
2020/1/2

Approximate weights of the components are shown. Clean all surfaces
where parts are to be installed.
Personal injury can result from driveline torque windup under load.
Unequal wheel speed can result in driveline torque windup which can
cause driveline components to be under load during disassembly.
Relieve the driveline torque windup before disassembly.
NOTICE
containing fluids.
Cat®
products.
1. Install Tooling (B) to stabilize the machine.
2/4
2020/1/2

2. Use Tooling (A) in order to raise the front axle until one of the wheels clears the ground.
This will release the driveline torque windup in the drive train. Lower the machine and
remove Tooling (A).
3. Disconnect and set tube (2) to the side. Set hose assembly (1) to the side.
Main drive shaft connection at the transfer gears.
3/4
2020/1/2

Main drive shaft connection at the transmission.
4. Attach a suitable lifting device to main drive shaft (3). The weight of main drive shaft (3) is
approximately 65 kg (143 lb).
5. Remove four bolts (4) and (5).
6. Remove main drive shaft (3) from the machine.
1. Install main drive shaft (3) in the reverse order of removal.
a. Inspect the drive shaft and replace any parts as needed.
b. Install the slip shaft with the female end toward the transmission.
c. Position main drive shaft (3) and align the keyways. Tighten bolts (4) and (5) to a
torque of 135 ± 20 N·m (100 ± 15 lb ft).
Thu Jan 2 10:25:17 UTC+0800 2020
4/4
2020/1/2

Shutdown SIS
Previous Screen
i06220256
Front Drive Shaft - Remove and Install
SMCS - 3253-010-FR
Removal Procedure
Table 1
Required Tools
A
8S-7610 Base 1
396-9840 Cylinder 1
350-7768 Electric Hydraulic Pump (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
8S-7615 Pin 1
Start By:
a. Install the steering frame lock.
Personal injury or death can result from improper lifting or blocking.
When a hoist or jack is used to lift any part or component, stand clear of
the area. Be sure the hoist or jack has the correct capacity to lift a
component. Install blocks or stands before performance of any work
under a heavy component.
1/3
2020/1/2

Approximate weights of the components are shown. Clean all surfaces
where parts are to be installed.
NOTICE
containing fluids.
Cat®
products.
1. Install Tooling (B) to stabilize the machine.
2/3
2020/1/2

2. Use tooling (A) in order to raise the front axle until one of the wheels clears the ground.
This will release the driveline torque windup in the drive train. Lower the front axle and
remove Tooling (A).
3. Mark the orientation of front drive shaft (2). The weight of front drive shaft (2) is
approximately 32 kg (70 lb). Remove eight bolts (1). Use two people and remove front
drive shaft (2).
1. Install front drive shaft (2) in the reverse order of removal.
a. Inspect front drive shaft (2) for damage and replace any parts as needed.
b. Position front drive shaft (2) and align keyways. Tighten eight bolts (1) to a torque of
135 ± 20 N·m (100 ± 15 lb ft).
Thu Jan 2 10:26:13 UTC+0800 2020
3/3
2020/1/2

Shutdown SIS
Previous Screen
i06220267
Hitch Drive Shaft - Remove and Install
SMCS - 3253-010
Removal Procedure
Table 1
Required Tools
A
8S-7610 Base 1
396-9840 Cylinder 1
350-7768 Electric Hydraulic Pump (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
8S-7615 Pin 1
Start By:
a. Install the steering frame lock.
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
1/3
2020/1/2

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Connect the steering frame lock link between the front and rear frames
before working on machine.
Do not disconnect the lock link until the machine is made operational
and the commissioning procedure is completed.
1. Use Tooling (B) in order to stabilize the machine.
2. Use Tooling (A) in order to raise the front axle until one of the wheels clears the ground.
This releases driveline torque windup in the front axle. Lower the front axle and remove
Tooling (A).
2/3
2020/1/2

3. The weight of hitch drive shaft (2) is approximately 37 kg (81 lb).
4. Mark orientation and remove eight bolts (1) and from hitch drive shaft (2).
5. Use two people in order to remove hitch drive shaft (2) from the machine.
1. Install hitch drive shaft (2) in the reverse order of removal.
a. Inspect hitch drive shaft (2) for damage and replace any parts as needed.
b. Align the keyways and install bolts (1) in order to connect hitch drive shaft (2).
c. Tighten bolts (1) to a torque of 105 ± 20 N·m (77 ± 15 lb ft).
Thu Jan 2 10:27:09 UTC+0800 2020
3/3
2020/1/2

Shutdown SIS
Previous Screen
i06222300
Hitch Drive Shaft Bearings - Remove
SMCS - 3253-011-BD
Removal Procedure
Table 1
Required Tools
A 154-6182 Forcing Bolt 2
B 136-1452 Internal Tip Pliers 1
C 8B-7551 Bearing Puller Gp 1
D 154-6181 Forcing Bolt 2
E 4C-3085 Two Jaw Puller 1
Start By:
a. Remove the center drive shaft.
b. Remove the hitch drive shaft.
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
1/6
2020/1/2

Connect the steering frame lock link between the front and rear frames
before working on machine.
Do not disconnect the lock link until the machine is made operational
and the commissioning procedure is completed.
Typical Example
View from the underside of the rear frame.
1. Remove bolts (1) in order to remove locking plate (2) from thrust flange (3) and bearing
carrier (4).
Typical Example
2. Turn over locking plate (2) and position the dowels on locking plate (2) into the holes in
thrust flange (3). Insert a suitable 3/4 inch breaker bar into the locking plate in order to turn
the thrust flange counterclockwise and remove thrust flange (3) from bearing carrier (4).
2/6
2020/1/2

Caterpillar Cat 745C Articulated Truck (Prefix LFK) Service Repair Manual (LFK00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 745C Articulated Truck (Prefix LFK) Service Repair Manual (LFK00001 and up).pdf

Similar to Caterpillar Cat 745C Articulated Truck (Prefix LFK) Service Repair Manual (LFK00001 and up).pdf (20)

More from yushantuanjing

More from yushantuanjing (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 745C Articulated Truck (Prefix LFK) Service Repair Manual (LFK00001 and up).pdf