Caterpillar Cat 740 Articulated Truck (Prefix B1P) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
740 Articulated Truck

Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK B1P
Configuration: 740 Articulated Truck B1P00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
735, 740 and 740 EJECTOR Articulated Trucks Engine Supplement
Media Number -RENR5137-05 Publication Date -01/09/2014 Date Updated -19/09/2014
i01543729
Gear Pump (Aftercooler) - Disassemble
SMCS - 5073-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
Start By:
A. Remove the gear pump (Aftercooler). Refer to Disassembly and Assembly, "Gear Pump
(Aftercooler) - Remove".
Illustration 1 g00802101
1. Remove O-ring seal (1) and two elbows (2) from gear pump (3) .
1/5
740 Articulated Truck B1P00001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2. Place the gear pump on suitable cribbing and remove adapter (4). Remove four bolts (5) in
order to remove plate (6) from housing (7) .
3. Remove two dowels (8), seal (9) and pressure plate (10) from housing (7) .
2/5
2020/1/25

4. Remove seal (11) and backup seal (12) from pressure plate (10) .
5. Remove gear shaft (13) and idler gear (14) from housing (7) .
6. Remove pressure plate (15) from housing (7). Refer to step 4 in order to remove the seals.
3/5
2020/1/25

7. Remove housing (7) from flange (16) .
8. Remove seal (17) from housing (7) .
4/5
2020/1/25

9. Use a suitable pin punch in order to remove lip seal (19) from flange (16). Use tool (A) and
remove two rings (20). Use the pin punch to remove lip seal (21) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 25 11:55:38 UTC+0800 2020
5/5
2020/1/25

Shutdown SIS
Previous Screen
i01544464
Gear Pump (Aftercooler) - Assemble
SMCS - 5073-016
Assembly Procedure
Table 1
Required Tools
B 1P-0510 Driver Gp 1
1. Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar
parts for replacement.
2. On assembly, lubricate all internal components with the lubricant that is being sealed.
1/5
2020/1/25

3. Use tool (B) to install lip seal (21) with the lip of the seal toward flange (16). Use tool (A)
to install two ring (20) into the ring grooves in flange (16). Use tool (B) to install lip seal
(19) with the lip of the seal away from flange (16) .
4. Install two dowels (18) into flange (16) .
2/5
2020/1/25

5. Install seal (17) into housing (7) .
6. Align housing (7) with the dowel in flange (16) and position the housing on the flange.
7. Install pressure plate (15) into housing (7). Refer to step 9 for the installation of the seals.
3/5
2020/1/25

8. Install idler gear (14) and gear shaft (13) into housing (7) .
9. Install seal (11) and backup seal (12) into pressure plate (10) .
10. Carefully install pressure plate (10) onto housing (7). Install seal (9) and two dowels (8) .
4/5
2020/1/25

11. Align plate (6) with the two dowels in housing (7) and install four bolts (5). Tighten the
bolts to a torque of 44.5 ± 3.5 N·m (33 ± 2.5 lb ft). Install adapter (4) .
12. Install two elbows (2) and O-ring seal (1) to gear pump (3) .
End By: Install the gear pump (Aftercooler). Refer to Disassembly and Assembly, "Gear Pump
(Aftercooler) - Install".
Sat Jan 25 11:56:33 UTC+0800 2020
5/5
2020/1/25

Shutdown SIS
Previous Screen
i01538164
Gear Pump (Aftercooler) - Install
SMCS - 5073-012
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar
parts for replacement.
2. Install O-ring seal (5) onto gear pump (2). Apply a light coat of the lubricant that is being
sealed to the O-ring seal.
1/3
2020/1/25

3. Align the splines on the shaft of gear pump (2) with the spline in the engine drive train and
install the gear pump. Install two bolts (4) and the washers.
4. Connect two hoses (3) to gear pump (2) .
2/3
2020/1/25

5. Install coupling (1) into gear pump (2) .
End By:
a. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove and Install".
b. Check the oil level in the steering system. Refer to Operation and Maintenance Manual,
"Steering System Oil Level - Check".
Sat Jan 25 11:57:29 UTC+0800 2020
3/3
2020/1/25

Shutdown SIS
Previous Screen
i01586593
Gear Pump (Hydraulic Fan) - Remove
SMCS - 5073-011-HFN
S/N - AXM1-UP
S/N - AZZ1-UP
S/N - B1P1-UP
S/N - B1R1-UP
Removal Procedure
Start By:
A. Tilt the Cab. Refer to Operation and Maintenance Manual, "Cab - Tilt".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
2020/1/25

The gear pump for the hydraulic fan on the 740 Articulated Truck is located on the back of the
piston pump for the steering under the cab on the right side of the machine.
The cab has been removed for photographic clarity.
1. Loosen the two retaining nuts and disconnect two hoses (1) from gear pump (2) .
2. Remove two bolts (3) with the washers in order to remove gear pump (2) from piston pump
(4). Remove the O-ring seal from pump (2) (not shown). The weight of the gear pump is
12.5 kg (28 lb).
Sat Jan 25 11:58:25 UTC+0800 2020
2/2
2020/1/25

Shutdown SIS
Previous Screen
i01586063
Gear Pump (Hydraulic Fan) - Disassemble
SMCS - 5073-015-HFN
Disassembly Procedure
Table 1
Required Tools
Start By:
A. Remove the gear pump (hydraulic fan). Refer to Disassembly and Assembly, "Gear Pump
(Hydraulic Fan) - Remove".
1/5
2020/1/25

1. Remove fitting (1) from body (2). Remove O-ring seal (3) from the fitting.
2. Remove fitting (4) from body (2). Remove O-ring seal (5) from the fitting.
2/5
2020/1/25

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

3. Remove four nuts (7) and four washers (8) that secure flange (6) to body (2). Separate the
flange from the body.
4. Remove O-ring seal (9) from the back face of flange (6) .
3/5
2020/1/25

Caterpillar Cat 740 Articulated Truck (Prefix B1P) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 740 Articulated Truck (Prefix B1P) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 740 Articulated Truck (Prefix B1P) Service Repair Manual Instant Download.pdf (20)

More from 9fiisekodkdmd

More from 9fiisekodkdmd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 740 Articulated Truck (Prefix B1P) Service Repair Manual Instant Download.pdf