SlideShare a Scribd company logo
1 of 25
Download to read offline
Product: ENGINE
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i02488070
Flywheel - Remove and Install
SMCS - 1156-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 2
B -
Guide Stud
1 - 14 by 6 inch
2
Start By:
a. Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed
Sensor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g01126776
1. Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1)
is approximately 170 kg (375 lb).
2. Remove two bolts (2) on each side of the crankshaft and install Tooling (B).
3. Remove remaining bolts (2).
4. Remove flywheel (1).
Note: If necessary, Use a prybar against Tooling (A) to remove the flywheel from the
crankshaft.
5. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 2
B -
Guide Stud
1 - 14 by 6 inch
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 2 g01126776
1. Raise the temperature of new ring gear (3). Install the ring gear on flywheel (1). Ensure that
the chamfer of the gear teeth will be toward the pinion of the starting motor.
2. Install Tooling (B) in the end of the crankshaft.
3. Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1)
is approximately 170 kg (375 lb).
4. Lift the flywheel into position onto Tooling (B). Ensure that the mark on the flywheel is
aligned with the mark on the crankshaft.
5. Apply clean engine oil to the threads of bolts (2). Install bolts (2).
6. Remove Tooling (A) and Tooling (B). Install remaining bolts (2). Tighten bolts (2) to a
torque of 1150 ± 60 N·m (848 ± 44 lb ft).
End By:
a. Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor
- Remove and Install".
3/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Product: ENGINE
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i03565063
Crankshaft Rear Seal and Wear Sleeve - Remove
SMCS - 1161-011; 7558-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
6V-3143
or
1U-7325
Distorter Adapter 1
C 5P-7409 Sleeve Distorter 1
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Every time that the crankshaft seal is removed from the wear sleeve, a
new wear sleeve and crankshaft seal must be installed.
Illustration 1 g00659239
1. Drill three evenly spaced holes in crankshaft rear seal (1) . Use Tooling (A) in order to
remove crankshaft rear seal (1) .
Illustration 2 g00659240
2. Insert Tooling (B) between the rear housing and wear sleeve (2) .
NOTICE
The use of excessive force on the sleeve distorter can cause the distorter
adapter to crack the housing. To help avoid damage to the engine, do
not use excessive force to remove the wear sleeve.
2/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Insert Tooling (C) between Tooling (B) and wear sleeve (2) . Carefully turn Tooling (C)
until the edge of the tool causes a crease in wear sleeve (2) .
Repeat this procedure several times around wear sleeve (2) until wear sleeve (2) can be
removed by hand.
3/3(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Product: ENGINE
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i06986865
Crankshaft Rear Seal and Wear Sleeve - Install
SMCS - 1161-012; 7558-012
Installation Procedure For Seals 113-8432 and 113-8433
Table 1
Required Tools
Tool Part Number Part Description Qty
D
6V-4003 (1)
Seal Locator As 1
2N-5006 ***#i06986865/i06603187.3*** Bolt 2
E 8T-3099 ***#i06986865/i06603187.3*** Seal Installer 1
F 9S-8858 ***#i06986865/i06603187.3*** Nut 1
G - (Loctite 620) -
H 484-7863 (2)
Tool As 1
(1)
For installation of seals 113-8432 and 113-8433
(2)
For Installation of seals 436-1478 and 436-1479
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the
crankshaft front seal and the wear sleeve are separated, these components cannot be used again.
1/4(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the
wear sleeve.
1. Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft
for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to
an out of round condition. Use a polishing cloth to remove any imperfections on the
crankshaft.
Illustration 1 g01136390
2. Clean the outside diameter of crankshaft (3) and the inside diameter of the new wear sleeve
(2). Clean the bore for the crankshaft front seal in front housing (4).Apply Tooling (G) to
the inner diameter of the wear sleeve and the surface of the crankshaft prior to assembly.
3. Install Tooling (D) on crankshaft (3).
4. Place crankshaft front seal (1) and wear sleeve (2) onto Tooling (D).
5. Position Tooling (E) onto Tooling (D). Lubricate the face of the washer on Tooling (F).
Install Tooling (F) onto Tooling (E). Tighten Tooling (F) until Tooling (E) contacts Tooling
(D).
6. Remove the Tooling from the crankshaft.
7. Check the crankshaft front seal and the wear sleeve for the correct installation.
Installation Procedure For Seals 436-1478 and 436-1479
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
NOTICE
Do not place engine oil on the crankshaft seal for installation.
Lubrication of the crankshaft seal can give a false indication of leakage
at a later time.
Note: Ensure that there are no imperfections on the mating surfaces of the crankshaft, the
installation tooling, or on the sealing surface of the crankshaft. Surface imperfections can distort
the seal during installation and will cause the seal to malfunction.
Illustration 2 g06042396
1. Using Tooling (H), install rear seal (1) as outlined in the following steps:
a. Install pilot (H1) to the crankshaft and install bolts (H2).
b. Position rear seal (1) onto pilot (H1).
c. Install driver (H3) onto the shaft of pilot (H1). Mark driver (H3) at the 12 O' Clock
position. Install bearing (H4) and nut (H5).
d. Tighten nut (H5) until the base of driver (H3) contacts the skirt of pilot (H1). Loosen
nut (H5) and rotate driver (H3) 180 degree. Retighten nut (H5) until driver (H3)
contacts the skirt of pilot (H1).
2. Remove Tooling (H).
End By:
a. Install the flywheel.
3/4(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i06705117
Flywheel Housing - Remove
SMCS - 1157-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
B
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
8B-7561 Step Plate 1
1P-0820 Hydraulic Puller 1
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
C 138-7573 Link Bracket 2
D -
Guide Stud
5/8 - 11 by 6 inch
2
E Loctite 7649 -
Start By:
a. Remove the starting motor. Refer to Disassembly and Assembly, "Air Starting Motor -
Remove". Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and
Install".
1/5(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
b. If the exhaust elbow is attached to the flywheel housing, remove the exhaust elbow and
remove the bracket for the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust
Elbow - Remove and Install".
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove".
d. Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed
Sensor - Remove and Install".
e. Remove the engine speed/timing sensor. Refer to Disassembly and Assembly, "Engine
Speed/Timing Sensor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01126909
1. Remove rear camshaft covers (1).
2. Remove timing pin (2) from the storage position.
3. Remove timing bolt (5) from the storage position. Remove cover (3) and plug (4) from the
flywheel housing.
4. Use Tooling (A) to turn the flywheel in order to install timing bolt (5) in the flywheel and
timing pin (2) in both camshafts. Refer to Testing and Adjusting, "Camshaft Timing". Refer
to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston".
2/5(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Remove the timing bolt from the flywheel.
6. Remove the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal and Wear Sleeve - Remove".
Illustration 2 g01126908
7. Remove tube (6).
8. Remove drain tubes (7) for the turbochargers. Remove the gaskets from the elbows.
9. Remove covers (8) and the gasket.
Illustration 3 g01316299
10. Remove bolt (9) and plate (10). Place the three washers from Tooling (B) behind plate (10)
and install bolt (9). Install Tooling (B) on camshaft drive gear (11). Apply 51675 kPa
(7500 psi) to the puller. Strike the screw on the puller with a hammer until camshaft drive
gear (11) is free from the camshaft. Remove Tooling (B) from the camshaft drive gear.
Remove camshaft drive gear (11) from the camshaft.
3/5(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Note: Plate (10) must be installed in order to keep camshaft drive gear (11) on the camshaft
during the removal procedure.
Illustration 4 g01316301
11. Remove bolt (12). Remove ring (13).
Illustration 5 g01316307
12. Place the three washers from Tooling (B) behind plate (10) and install bolt (12). Install
Tooling (B) on camshaft drive gear (14). Use Tooling (B) in order to remove camshaft drive
gear (14) from the camshaft. Apply 51675 kPa (7500 psi) to the puller. Strike the screw on
the puller with a hammer until camshaft drive gear (14) is free from the camshaft. Remove
Tooling (B) from the camshaft drive gear. Remove camshaft drive gear (14) from the
camshaft.
Note: Plate (10) must be installed in order to keep camshaft drive gear (14) on the camshaft
during the removal procedure.
4/5(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 6 g01316311
13. Install Tooling (C) and a suitable lifting device on flywheel housing (16). The weight of
flywheel housing (16) is approximately 235 kg (518 lb).
14. Remove two bolts (17) and install Tooling (D). Remove the remaining bolts (17) and
remove flywheel housing (16) from the cylinder block.
15. If necessary, remove plugs (15) from the flywheel housing.
Note: Ensure that the rear gear group and the crankshaft are properly protected during the
cleaning procedure. Ensure that the bolts are cleaned with a wire brush in order to remove
debris or residue. Ensure that the bores for the bolts in the cylinder block are tapped again.
Ensure that the bores for the bolts are cleaned in order to remove debris or residue.
16. After removing flywheel housing (16), clean the mating surface of the cylinder block and
the mating surface of the flywheel housing with Tooling (E). If necessary, use a gasket
scraper and a solvent in order to remove any residual gasket material. Both mating surfaces
must be clean, dry, and free of any oil before installation.
5/5(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Product: ENGINE
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i07522043
Flywheel Housing - Install
SMCS - 1157-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 138-7573 Link Bracket 2
D -
Guide Stud
5/8 - 11 by 6 inch
2
F -(1)
Loctite 5127 -
(1)
EAME
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Note: Refer to Engine News, 27, March 2006, "Sealing and Installing the Flywheel
Housing" for more information.
1. Ensure that the mating surfaces of the flywheel housing and the engine block are clean.
Both mating surfaces must be clean, dry, and free of any oil before Tooling (F) is applied.
Illustration 1 g01317446
2. Apply a 6.0 mm (0.25 inch) bead of Tooling (F) to the mating surface of the flywheel
housing. Refer to Illustration 1.
2/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 2 g01316311
3. Install Tooling (D) into the cylinder block.
4. Install Tooling (C) and a suitable lifting device on flywheel housing (16). The weight of
flywheel housing (16) is approximately 235 kg (518 lb).
5. Lift the flywheel housing into position onto Tooling (D).
6. Install bolts (17) and the hard washers that secure the flywheel housing to the cylinder
block. Remove Tooling (D) and install remaining bolts (17) and the hard washers.
Note: Refer to Parts Manual for the correct positions for bolts that secure the flywheel
housing to the cylinder block.
7. Tighten bolts (17) evenly. Tighten the 1/2 - NC bolts to a torque of 135 ± 20 N·m
(100 ± 15 lb ft). Tighten the 5/8 - NC bolts to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
8. Tighten plugs (15) to a torque of 70 ± 15 N·m (50 ± 11 lb ft).
9. Install the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal and Wear Sleeve - Install".
Illustration 3 g01140296
10. Install timing bolt (5) in the flywheel. Ensure that timing pin (2) is installed in each
camshaft. Refer to Testing and Adjusting, "Camshaft Timing". Refer to Testing and
Adjusting, "Finding the Top Center Position for the No. 1 Piston".
3/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g01316352
Illustration 5 g01316354
11. Use the following procedure to install camshaft drive gear (11) and camshaft drive gear
(14).
a. Clean the taper of the camshaft and the tapered bore of the camshaft gear with a lint
free cloth saturated with solvent to remove oil. Clean the parts again with a lint free
alcohol wipe to remove any residue. The alcohol wipe will dirty after cleaning the
parts. Clean the parts again with a lint free alcohol wipe until no residue is left on the
alcohol wipe.
Note: The taper of the camshaft and the tapered bore of the camshaft gear must be
clean, dry, and free of residue before assembly.
b. Ensure that the camshaft timing pins and the timing pin for the flywheel are installed.
c. Place camshaft drive gear (11) and camshaft drive gear (14) in position. Remove the
backlash by rotating the gears in the opposite direction of camshaft rotation.
Note: For "Standard Rotation" engines, turn the camshaft drive gears
COUNTERCLOCKWISE. For "Reverse Rotation" engines, turn the camshaft drive
gears CLOCKWISE.
d. Install bolt (9) and plate (10).
4/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
e. Install bolt (12) and ring (13). Ensure that the hole in the ring is properly seated on the
locating pin.
f. Tighten the bolt to a torque of 360 N·m (265 lb ft).
g. Place a mark on the bolt.
h. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver
with a hammer, three times, or four times.
i. Tighten the bolt again to a torque of 360 N·m (265 lb ft).
j. Repeat Steps 11.h and 11.i until the mark has turned at least 90 degrees.
Illustration 6 g01126909
12. Remove the timing pin from the camshafts. Install timing pin (2) in the storage position.
Install rear camshaft covers (1).
13. Remove the timing bolt from the flywheel. Install plug (4) in the timing hole. Install cover
(3) and timing bolt (5) in the storage position on the flywheel housing.
5/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 7 g01126908
14. Install tube (6) if equipped.
15. Install the gaskets on the elbows. Install drain tubes (7) for the turbochargers.
16. Install the gasket and covers (8) on the flywheel housing.
End By:
a. Install the engine speed/timing sensor. Refer to Disassembly and Assembly, "Engine
Speed/Timing Sensor - Remove and Install".
b. Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor
- Remove and Install".
c. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
d. If the exhaust elbow was removed, install the exhaust elbow. Refer to Disassembly and
Assembly, "Exhaust Elbow - Remove and Install".
e. Install the starting motors. Refer to Disassembly and Assembly, "Air Starting Motor -
Install". Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and
Install".
6/6(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Product: ENGINE
Model: 3512E ENGINE SY3
Configuration: 3512E Marine Engine SY300001-UP
Disassembly and Assembly
3512E and 3516E Marine Engines
Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018
i07525193
Engine Oil Sequence Valves - Remove and Install
SMCS - 1332-010
Removal Procedure
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
b. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g01135024
1. Remove bolts (1) and thrust plate (2). Remove balancer gear (3) from the balancer gear
shaft.
Note: The balancer gear is for the 3508C engine. The 3512C Engine, 3512E Engine, and the
3516C Engine do not have the balancer gear on the front of the engine.
Illustration 2 g01135028
Personal injury can result from parts and/or covers under spring
pressure.
2/7(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. Remove bolts (4) and cover (5) from the front of the cylinder block.
3. Remove plunger assembly (6) and spring (7) from the cylinder block.
Illustration 3 g01135030
4. Remove bolts (12) and thrust plate (13). Remove cluster idler gear (14) from the rear of the
cylinder block.
5. Remove bolts (8), idler shaft (9), camshaft idler gear (10), and thrust washer (11).
3/7(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g01135029
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
6. Remove bolts (15) and cover (16) from the rear of the cylinder block.
7. Remove plunger assembly (17) and spring (18) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g01135029
4/7(W)
w
2022/4/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

More Related Content

Similar to Caterpillar Cat 3512E Marine Engine (Prefix SY3) Service Repair Manual Instant Download (SY300001 and up).pdf

Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...cfvdssd
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...fujkse9didkke3
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...km7seyrduhdw
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...orrf0370383
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...8fusejkdmd9i
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...fuusejkddmmd3e
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...fujsekmd9idd
 
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...fjjseksxckmdme
 
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...fjkskedmme
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...jdjkskmikdkmd
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...paws21610697
 
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...ifkkdmdmdm
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...jdksme9ddkkd
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...f8uuseijdkmd3e
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...f7djidksmd3e
 

Similar to Caterpillar Cat 3512E Marine Engine (Prefix SY3) Service Repair Manual Instant Download (SY300001 and up).pdf (15)

Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual Inst...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
 
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
Caterpillar Cat C18 Industrial Engine (Prefix JDA) Service Repair Manual (JDA...
 
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
 
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
Caterpillar cat c18 industrial engine (prefix jda) service repair manual (jda...
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
 
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...
Caterpillar cat c13 industrial engine (prefix kwj) service repair manual (kwj...
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
 
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ...
 

More from ti76cui

Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...
Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...
Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...ti76cui
 
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...ti76cui
 
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...ti76cui
 
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...ti76cui
 
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...ti76cui
 
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...ti76cui
 
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...ti76cui
 
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...ti76cui
 
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...ti76cui
 
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...ti76cui
 
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...ti76cui
 
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...ti76cui
 
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...ti76cui
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...ti76cui
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...ti76cui
 

More from ti76cui (20)

Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...
Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...
Caterpillar Cat D5R2 TRACK-TYPE TRACTOR (Prefix WRE) Service Repair Manual In...
 
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...
Caterpillar Cat D5N TRACK-TYPE TRACTOR (Prefix AKD) Service Repair Manual Ins...
 
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...
Caterpillar Cat D5K XL TRACK-TYPE TRACTOR (Prefix WWW) Service Repair Manual ...
 
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix MT3) Service Repair Manual...
 
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...
Caterpillar Cat D4K2 XL TRACK-TYPE TRACTOR (Prefix KM2) Service Repair Manual...
 
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...
 
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Inst...
 
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix N3F) Service Repair Manual Inst...
 
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...
Caterpillar Cat C13 Industrial Engine (Prefix LGK) Service Repair Manual Inst...
 
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...
Caterpillar Cat C2.2 Industrial Engine (Prefix J26) Service Repair Manual Ins...
 
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...
Caterpillar Cat 3512B Industrial Engine (Prefix BR2) Service Repair Manual In...
 
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...
Caterpillar Cat 3512 Industrial Engine (Prefix SR2) Service Repair Manual Ins...
 
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...
 
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...
Caterpillar Cat 988B Wheel Loader (Prefix 50W) Service Repair Manual Instant ...
 
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...
Caterpillar Cat 988 988K XE Wheel Loader (Prefix E8X) Service Repair Manual I...
 
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...
Caterpillar Cat 977K TRACK LOADER (Prefix 48J) Service Repair Manual Instant ...
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 48J) Service Repair Manual Ins...
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
 
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
Caterpillar Cat 977K 977L TRACK LOADER (Prefix 11K) Service Repair Manual Ins...
 

Recently uploaded

一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样
一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样
一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样fsdfdsgf
 
Nokia Drone Networks - Customer Presentation - MWC2.pdf
Nokia Drone Networks - Customer Presentation - MWC2.pdfNokia Drone Networks - Customer Presentation - MWC2.pdf
Nokia Drone Networks - Customer Presentation - MWC2.pdfJosFerro15
 
Catalogue Yamaha Nouvo 115 S / Nouvo .pdf
Catalogue Yamaha Nouvo 115 S / Nouvo .pdfCatalogue Yamaha Nouvo 115 S / Nouvo .pdf
Catalogue Yamaha Nouvo 115 S / Nouvo .pdfHafizLaziz
 
原版定制奥尔良大学毕业证文凭证书密封成绩单
原版定制奥尔良大学毕业证文凭证书密封成绩单原版定制奥尔良大学毕业证文凭证书密封成绩单
原版定制奥尔良大学毕业证文凭证书密封成绩单ybefz
 
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样fsdfdsgf
 
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could Mean
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could MeanIs Your Porsche Cayenne Radio On The Fritz Here's What It Could Mean
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could MeanHuron Automotive
 
Battery Management System Circuit Diagram.pdf
Battery Management System Circuit Diagram.pdfBattery Management System Circuit Diagram.pdf
Battery Management System Circuit Diagram.pdfElectric Vehicle Geek
 
原版制作麦考瑞大学毕业证成绩单原件一模一样
原版制作麦考瑞大学毕业证成绩单原件一模一样原版制作麦考瑞大学毕业证成绩单原件一模一样
原版制作麦考瑞大学毕业证成绩单原件一模一样hbgfewda
 
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样yuslkdal
 
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书egfdgfd
 
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样A
 
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一0uyfyq0q4
 
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerKapil Thakar
 
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptx
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptxSolar Photovoltaic Plant Project Proposal by Slidesgo.pptx
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptxAmarHaddad
 
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书egfdgfd
 
一比一原版北雷克斯学院毕业证成绩单原件一模一样
一比一原版北雷克斯学院毕业证成绩单原件一模一样一比一原版北雷克斯学院毕业证成绩单原件一模一样
一比一原版北雷克斯学院毕业证成绩单原件一模一样CC
 
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...Bijay Sharma
 
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagra
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat ViagraToko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagra
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagraadet6151
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceKapil Thakar
 
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp Number 24/7
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp  Number 24/7ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp  Number 24/7
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp Number 24/7komalsharmaa480
 

Recently uploaded (20)

一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样
一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样
一比一原版(Temple毕业证书)美国天普大学毕业证成绩单原件一模一样
 
Nokia Drone Networks - Customer Presentation - MWC2.pdf
Nokia Drone Networks - Customer Presentation - MWC2.pdfNokia Drone Networks - Customer Presentation - MWC2.pdf
Nokia Drone Networks - Customer Presentation - MWC2.pdf
 
Catalogue Yamaha Nouvo 115 S / Nouvo .pdf
Catalogue Yamaha Nouvo 115 S / Nouvo .pdfCatalogue Yamaha Nouvo 115 S / Nouvo .pdf
Catalogue Yamaha Nouvo 115 S / Nouvo .pdf
 
原版定制奥尔良大学毕业证文凭证书密封成绩单
原版定制奥尔良大学毕业证文凭证书密封成绩单原版定制奥尔良大学毕业证文凭证书密封成绩单
原版定制奥尔良大学毕业证文凭证书密封成绩单
 
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样
一比一原版曼彻斯特城市大学毕业证成绩单原件一模一样
 
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could Mean
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could MeanIs Your Porsche Cayenne Radio On The Fritz Here's What It Could Mean
Is Your Porsche Cayenne Radio On The Fritz Here's What It Could Mean
 
Battery Management System Circuit Diagram.pdf
Battery Management System Circuit Diagram.pdfBattery Management System Circuit Diagram.pdf
Battery Management System Circuit Diagram.pdf
 
原版制作麦考瑞大学毕业证成绩单原件一模一样
原版制作麦考瑞大学毕业证成绩单原件一模一样原版制作麦考瑞大学毕业证成绩单原件一模一样
原版制作麦考瑞大学毕业证成绩单原件一模一样
 
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样
原版定制(UniSA毕业证书)澳大利亚南澳大学毕业证原件一模一样
 
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书
一比一定制加拿大安大略理工大学毕业证(UOIT毕业证书)学位证书
 
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样
一比一原版(Rutgers毕业证书)罗格斯大学毕业证成绩单原件一模一样
 
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一
如何办理澳洲南澳大学毕业证(UniSA毕业证书)成绩单本科学位证原版一比一
 
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
 
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptx
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptxSolar Photovoltaic Plant Project Proposal by Slidesgo.pptx
Solar Photovoltaic Plant Project Proposal by Slidesgo.pptx
 
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书
一比一定制加拿大新喀里多尼亚学院毕业证(UofL毕业证书)学位证书
 
一比一原版北雷克斯学院毕业证成绩单原件一模一样
一比一原版北雷克斯学院毕业证成绩单原件一模一样一比一原版北雷克斯学院毕业证成绩单原件一模一样
一比一原版北雷克斯学院毕业证成绩单原件一模一样
 
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
 
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagra
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat ViagraToko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagra
Toko Jual Viagra Asli Di Surabaya 081229400522 COD Obat Kuat Viagra
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming Sequence
 
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp Number 24/7
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp  Number 24/7ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp  Number 24/7
ℂall Girls Chirag Delhi ℂall Now Chhaya ☎ 9899900591 WhatsApp Number 24/7
 

Caterpillar Cat 3512E Marine Engine (Prefix SY3) Service Repair Manual Instant Download (SY300001 and up).pdf

  • 1. Product: ENGINE Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i02488070 Flywheel - Remove and Install SMCS - 1156-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7573 Lifting Bracket 2 B - Guide Stud 1 - 14 by 6 inch 2 Start By: a. Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 2. Illustration 1 g01126776 1. Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb). 2. Remove two bolts (2) on each side of the crankshaft and install Tooling (B). 3. Remove remaining bolts (2). 4. Remove flywheel (1). Note: If necessary, Use a prybar against Tooling (A) to remove the flywheel from the crankshaft. 5. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1). Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 138-7573 Lifting Bracket 2 B - Guide Stud 1 - 14 by 6 inch 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 3. Illustration 2 g01126776 1. Raise the temperature of new ring gear (3). Install the ring gear on flywheel (1). Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor. 2. Install Tooling (B) in the end of the crankshaft. 3. Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb). 4. Lift the flywheel into position onto Tooling (B). Ensure that the mark on the flywheel is aligned with the mark on the crankshaft. 5. Apply clean engine oil to the threads of bolts (2). Install bolts (2). 6. Remove Tooling (A) and Tooling (B). Install remaining bolts (2). Tighten bolts (2) to a torque of 1150 ± 60 N·m (848 ± 44 lb ft). End By: a. Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install". 3/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 4. Product: ENGINE Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i03565063 Crankshaft Rear Seal and Wear Sleeve - Remove SMCS - 1161-011; 7558-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1U-7600 Slide Hammer Puller 1 B 6V-3143 or 1U-7325 Distorter Adapter 1 C 5P-7409 Sleeve Distorter 1 Start By: A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE 1/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 5. Every time that the crankshaft seal is removed from the wear sleeve, a new wear sleeve and crankshaft seal must be installed. Illustration 1 g00659239 1. Drill three evenly spaced holes in crankshaft rear seal (1) . Use Tooling (A) in order to remove crankshaft rear seal (1) . Illustration 2 g00659240 2. Insert Tooling (B) between the rear housing and wear sleeve (2) . NOTICE The use of excessive force on the sleeve distorter can cause the distorter adapter to crack the housing. To help avoid damage to the engine, do not use excessive force to remove the wear sleeve. 2/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 6. 3. Insert Tooling (C) between Tooling (B) and wear sleeve (2) . Carefully turn Tooling (C) until the edge of the tool causes a crease in wear sleeve (2) . Repeat this procedure several times around wear sleeve (2) until wear sleeve (2) can be removed by hand. 3/3(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 7. Product: ENGINE Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i06986865 Crankshaft Rear Seal and Wear Sleeve - Install SMCS - 1161-012; 7558-012 Installation Procedure For Seals 113-8432 and 113-8433 Table 1 Required Tools Tool Part Number Part Description Qty D 6V-4003 (1) Seal Locator As 1 2N-5006 ***#i06986865/i06603187.3*** Bolt 2 E 8T-3099 ***#i06986865/i06603187.3*** Seal Installer 1 F 9S-8858 ***#i06986865/i06603187.3*** Nut 1 G - (Loctite 620) - H 484-7863 (2) Tool As 1 (1) For installation of seals 113-8432 and 113-8433 (2) For Installation of seals 436-1478 and 436-1479 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the crankshaft front seal and the wear sleeve are separated, these components cannot be used again. 1/4(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 8. Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the wear sleeve. 1. Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth to remove any imperfections on the crankshaft. Illustration 1 g01136390 2. Clean the outside diameter of crankshaft (3) and the inside diameter of the new wear sleeve (2). Clean the bore for the crankshaft front seal in front housing (4).Apply Tooling (G) to the inner diameter of the wear sleeve and the surface of the crankshaft prior to assembly. 3. Install Tooling (D) on crankshaft (3). 4. Place crankshaft front seal (1) and wear sleeve (2) onto Tooling (D). 5. Position Tooling (E) onto Tooling (D). Lubricate the face of the washer on Tooling (F). Install Tooling (F) onto Tooling (E). Tighten Tooling (F) until Tooling (E) contacts Tooling (D). 6. Remove the Tooling from the crankshaft. 7. Check the crankshaft front seal and the wear sleeve for the correct installation. Installation Procedure For Seals 436-1478 and 436-1479 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/4(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 9. NOTICE Do not place engine oil on the crankshaft seal for installation. Lubrication of the crankshaft seal can give a false indication of leakage at a later time. Note: Ensure that there are no imperfections on the mating surfaces of the crankshaft, the installation tooling, or on the sealing surface of the crankshaft. Surface imperfections can distort the seal during installation and will cause the seal to malfunction. Illustration 2 g06042396 1. Using Tooling (H), install rear seal (1) as outlined in the following steps: a. Install pilot (H1) to the crankshaft and install bolts (H2). b. Position rear seal (1) onto pilot (H1). c. Install driver (H3) onto the shaft of pilot (H1). Mark driver (H3) at the 12 O' Clock position. Install bearing (H4) and nut (H5). d. Tighten nut (H5) until the base of driver (H3) contacts the skirt of pilot (H1). Loosen nut (H5) and rotate driver (H3) 180 degree. Retighten nut (H5) until driver (H3) contacts the skirt of pilot (H1). 2. Remove Tooling (H). End By: a. Install the flywheel. 3/4(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 10. Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i06705117 Flywheel Housing - Remove SMCS - 1157-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 238-9586 Camshaft Drive Group 1 B 8B-7548 Push-Puller Tool Group 1 8B-7559 Adapter 2 8B-7561 Step Plate 1 1P-0820 Hydraulic Puller 1 5H-1504 Hard Washer 3 9U-6600 Hand Hydraulic Pump 1 C 138-7573 Link Bracket 2 D - Guide Stud 5/8 - 11 by 6 inch 2 E Loctite 7649 - Start By: a. Remove the starting motor. Refer to Disassembly and Assembly, "Air Starting Motor - Remove". Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". 1/5(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 11. b. If the exhaust elbow is attached to the flywheel housing, remove the exhaust elbow and remove the bracket for the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install". c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove". d. Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install". e. Remove the engine speed/timing sensor. Refer to Disassembly and Assembly, "Engine Speed/Timing Sensor - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g01126909 1. Remove rear camshaft covers (1). 2. Remove timing pin (2) from the storage position. 3. Remove timing bolt (5) from the storage position. Remove cover (3) and plug (4) from the flywheel housing. 4. Use Tooling (A) to turn the flywheel in order to install timing bolt (5) in the flywheel and timing pin (2) in both camshafts. Refer to Testing and Adjusting, "Camshaft Timing". Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston". 2/5(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 12. 5. Remove the timing bolt from the flywheel. 6. Remove the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Remove". Illustration 2 g01126908 7. Remove tube (6). 8. Remove drain tubes (7) for the turbochargers. Remove the gaskets from the elbows. 9. Remove covers (8) and the gasket. Illustration 3 g01316299 10. Remove bolt (9) and plate (10). Place the three washers from Tooling (B) behind plate (10) and install bolt (9). Install Tooling (B) on camshaft drive gear (11). Apply 51675 kPa (7500 psi) to the puller. Strike the screw on the puller with a hammer until camshaft drive gear (11) is free from the camshaft. Remove Tooling (B) from the camshaft drive gear. Remove camshaft drive gear (11) from the camshaft. 3/5(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 13. Note: Plate (10) must be installed in order to keep camshaft drive gear (11) on the camshaft during the removal procedure. Illustration 4 g01316301 11. Remove bolt (12). Remove ring (13). Illustration 5 g01316307 12. Place the three washers from Tooling (B) behind plate (10) and install bolt (12). Install Tooling (B) on camshaft drive gear (14). Use Tooling (B) in order to remove camshaft drive gear (14) from the camshaft. Apply 51675 kPa (7500 psi) to the puller. Strike the screw on the puller with a hammer until camshaft drive gear (14) is free from the camshaft. Remove Tooling (B) from the camshaft drive gear. Remove camshaft drive gear (14) from the camshaft. Note: Plate (10) must be installed in order to keep camshaft drive gear (14) on the camshaft during the removal procedure. 4/5(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 14. Illustration 6 g01316311 13. Install Tooling (C) and a suitable lifting device on flywheel housing (16). The weight of flywheel housing (16) is approximately 235 kg (518 lb). 14. Remove two bolts (17) and install Tooling (D). Remove the remaining bolts (17) and remove flywheel housing (16) from the cylinder block. 15. If necessary, remove plugs (15) from the flywheel housing. Note: Ensure that the rear gear group and the crankshaft are properly protected during the cleaning procedure. Ensure that the bolts are cleaned with a wire brush in order to remove debris or residue. Ensure that the bores for the bolts in the cylinder block are tapped again. Ensure that the bores for the bolts are cleaned in order to remove debris or residue. 16. After removing flywheel housing (16), clean the mating surface of the cylinder block and the mating surface of the flywheel housing with Tooling (E). If necessary, use a gasket scraper and a solvent in order to remove any residual gasket material. Both mating surfaces must be clean, dry, and free of any oil before installation. 5/5(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 15. Product: ENGINE Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i07522043 Flywheel Housing - Install SMCS - 1157-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty C 138-7573 Link Bracket 2 D - Guide Stud 5/8 - 11 by 6 inch 2 F -(1) Loctite 5127 - (1) EAME NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. 1/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 16. Note: Refer to Engine News, 27, March 2006, "Sealing and Installing the Flywheel Housing" for more information. 1. Ensure that the mating surfaces of the flywheel housing and the engine block are clean. Both mating surfaces must be clean, dry, and free of any oil before Tooling (F) is applied. Illustration 1 g01317446 2. Apply a 6.0 mm (0.25 inch) bead of Tooling (F) to the mating surface of the flywheel housing. Refer to Illustration 1. 2/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 17. Illustration 2 g01316311 3. Install Tooling (D) into the cylinder block. 4. Install Tooling (C) and a suitable lifting device on flywheel housing (16). The weight of flywheel housing (16) is approximately 235 kg (518 lb). 5. Lift the flywheel housing into position onto Tooling (D). 6. Install bolts (17) and the hard washers that secure the flywheel housing to the cylinder block. Remove Tooling (D) and install remaining bolts (17) and the hard washers. Note: Refer to Parts Manual for the correct positions for bolts that secure the flywheel housing to the cylinder block. 7. Tighten bolts (17) evenly. Tighten the 1/2 - NC bolts to a torque of 135 ± 20 N·m (100 ± 15 lb ft). Tighten the 5/8 - NC bolts to a torque of 270 ± 40 N·m (200 ± 30 lb ft). 8. Tighten plugs (15) to a torque of 70 ± 15 N·m (50 ± 11 lb ft). 9. Install the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Install". Illustration 3 g01140296 10. Install timing bolt (5) in the flywheel. Ensure that timing pin (2) is installed in each camshaft. Refer to Testing and Adjusting, "Camshaft Timing". Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston". 3/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 18. Illustration 4 g01316352 Illustration 5 g01316354 11. Use the following procedure to install camshaft drive gear (11) and camshaft drive gear (14). a. Clean the taper of the camshaft and the tapered bore of the camshaft gear with a lint free cloth saturated with solvent to remove oil. Clean the parts again with a lint free alcohol wipe to remove any residue. The alcohol wipe will dirty after cleaning the parts. Clean the parts again with a lint free alcohol wipe until no residue is left on the alcohol wipe. Note: The taper of the camshaft and the tapered bore of the camshaft gear must be clean, dry, and free of residue before assembly. b. Ensure that the camshaft timing pins and the timing pin for the flywheel are installed. c. Place camshaft drive gear (11) and camshaft drive gear (14) in position. Remove the backlash by rotating the gears in the opposite direction of camshaft rotation. Note: For "Standard Rotation" engines, turn the camshaft drive gears COUNTERCLOCKWISE. For "Reverse Rotation" engines, turn the camshaft drive gears CLOCKWISE. d. Install bolt (9) and plate (10). 4/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 19. e. Install bolt (12) and ring (13). Ensure that the hole in the ring is properly seated on the locating pin. f. Tighten the bolt to a torque of 360 N·m (265 lb ft). g. Place a mark on the bolt. h. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver with a hammer, three times, or four times. i. Tighten the bolt again to a torque of 360 N·m (265 lb ft). j. Repeat Steps 11.h and 11.i until the mark has turned at least 90 degrees. Illustration 6 g01126909 12. Remove the timing pin from the camshafts. Install timing pin (2) in the storage position. Install rear camshaft covers (1). 13. Remove the timing bolt from the flywheel. Install plug (4) in the timing hole. Install cover (3) and timing bolt (5) in the storage position on the flywheel housing. 5/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 20. Illustration 7 g01126908 14. Install tube (6) if equipped. 15. Install the gaskets on the elbows. Install drain tubes (7) for the turbochargers. 16. Install the gasket and covers (8) on the flywheel housing. End By: a. Install the engine speed/timing sensor. Refer to Disassembly and Assembly, "Engine Speed/Timing Sensor - Remove and Install". b. Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install". c. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install". d. If the exhaust elbow was removed, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install". e. Install the starting motors. Refer to Disassembly and Assembly, "Air Starting Motor - Install". Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". 6/6(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 21. Product: ENGINE Model: 3512E ENGINE SY3 Configuration: 3512E Marine Engine SY300001-UP Disassembly and Assembly 3512E and 3516E Marine Engines Media Number -M0075247-08 Publication Date -01/09/2018 Date Updated -11/09/2018 i07525193 Engine Oil Sequence Valves - Remove and Install SMCS - 1332-010 Removal Procedure Start By: a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove". b. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/7(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 22. Illustration 1 g01135024 1. Remove bolts (1) and thrust plate (2). Remove balancer gear (3) from the balancer gear shaft. Note: The balancer gear is for the 3508C engine. The 3512C Engine, 3512E Engine, and the 3516C Engine do not have the balancer gear on the front of the engine. Illustration 2 g01135028 Personal injury can result from parts and/or covers under spring pressure. 2/7(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 23. Suggest: For more complete manuals. Please go to the home page. https://www.ebooklibonline.com If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
  • 24. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. 2. Remove bolts (4) and cover (5) from the front of the cylinder block. 3. Remove plunger assembly (6) and spring (7) from the cylinder block. Illustration 3 g01135030 4. Remove bolts (12) and thrust plate (13). Remove cluster idler gear (14) from the rear of the cylinder block. 5. Remove bolts (8), idler shaft (9), camshaft idler gear (10), and thrust washer (11). 3/7(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 25. Illustration 4 g01135029 Personal injury can result from parts and/or covers under spring pressure. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. 6. Remove bolts (15) and cover (16) from the rear of the cylinder block. 7. Remove plunger assembly (17) and spring (18) from the cylinder block. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 5 g01135029 4/7(W) w 2022/4/3 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...