This document provides instructions for removing and installing piston cooling jets on a C13 Industrial Engine.
The removal procedure involves using a puller tool to remove the jets from the cylinder block. For installation, new jets are pressed into the cylinder block using a pilot and driver tool. Proper orientation of the jets is important for correct cooling.
The document provides instructions for removing and installing a cylinder liner on a C13 Industrial Engine. It describes using puller tools to remove the liner and checking measurements when installing the new liner. Proper installation of camshaft bearings and timing of the camshaft gear to crankshaft gear is emphasized.
- The document provides instructions for removing and installing a cylinder liner on a C13 Industrial Engine.
- To remove the liner, drain the coolant and use a liner puller tool by inserting it into the liner and pulling it out of the engine block.
- To install the new liner, apply a sealant to the block mating surface, insert the liner and check that it is flush with the top of the block.
This document provides installation and removal instructions for various engine components of a Caterpillar C13 Industrial Engine, including:
1. Camshaft installation which requires using alignment tools and ensuring timing marks are aligned.
2. Camshaft gear removal which involves pressing off the gear and removing a woodruff key.
3. Camshaft bearing installation which uses a tool to set the bearing depths correctly.
It provides detailed step-by-step instructions and illustrations for precise reassembly.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, bolts and the housing itself.
- Procedures for removing and installing the front gear group, which involves removing shafts, bushings, plates and gears.
- Steps for removing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety and cleaning notes are included to handle fluids and prevent contamination.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, and bolts.
- Procedures for removing and installing the front gear group, which involves removing shafts and bushings.
- Steps for removing and installing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which houses components like the oil filter and dampers.
- Procedures for removing and installing the front gear group, which involves bushings and shafts.
- Steps for removing the rear housing, which covers the rear of the engine and requires disconnecting hoses and brackets.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
The document provides instructions for removing and installing a cylinder liner on a C13 Industrial Engine. It describes using puller tools to remove the liner and checking measurements when installing the new liner. Proper installation of camshaft bearings and timing of the camshaft gear to crankshaft gear is emphasized.
- The document provides instructions for removing and installing a cylinder liner on a C13 Industrial Engine.
- To remove the liner, drain the coolant and use a liner puller tool by inserting it into the liner and pulling it out of the engine block.
- To install the new liner, apply a sealant to the block mating surface, insert the liner and check that it is flush with the top of the block.
This document provides installation and removal instructions for various engine components of a Caterpillar C13 Industrial Engine, including:
1. Camshaft installation which requires using alignment tools and ensuring timing marks are aligned.
2. Camshaft gear removal which involves pressing off the gear and removing a woodruff key.
3. Camshaft bearing installation which uses a tool to set the bearing depths correctly.
It provides detailed step-by-step instructions and illustrations for precise reassembly.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, bolts and the housing itself.
- Procedures for removing and installing the front gear group, which involves removing shafts, bushings, plates and gears.
- Steps for removing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety and cleaning notes are included to handle fluids and prevent contamination.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, and bolts.
- Procedures for removing and installing the front gear group, which involves removing shafts and bushings.
- Steps for removing and installing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which houses components like the oil filter and dampers.
- Procedures for removing and installing the front gear group, which involves bushings and shafts.
- Steps for removing the rear housing, which covers the rear of the engine and requires disconnecting hoses and brackets.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive, which involves removing pulleys, gears, bearings, seals, and other components.
2) Removing and installing the valve mechanism cover and valve mechanism cover base, which connect to the cylinder head.
3) Removing the rocker arm and shaft assembly, which controls the valves.
4) Disassembling the rocker arm, including removing adjustment screws and seals.
The document contains detailed step-by-step instructions accompanied by illustrations and lists of required tools for each procedure. Safety notices are provided to keep parts clean and prevent damage.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive, which involves removing pulleys, gears, bearings, seals, and other components.
2) Removing and installing the valve mechanism cover and valve mechanism cover base, which connect to the cylinder head.
3) Removing the rocker arm and shaft assembly, which controls the valves.
4) Disassembling the rocker arm, involving removing adjustment screws and other small parts.
The document contains detailed step-by-step instructions accompanied by illustrations and lists of required tools for each procedure. Safety notices are provided to keep parts clean and prevent
This document provides instructions for servicing components of a C27 Industrial Engine, including:
- Disassembling and assembling the auxiliary drive (front).
- Removing and installing the valve mechanism cover and valve mechanism cover base.
- Removing the rocker arm and shaft assembly.
- Disassembling and assembling the rocker arms.
The summaries provide the essential steps and components for each service procedure in 3 sentences or less.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine. It describes how to remove and install the auxiliary drive, valve mechanism covers, valve mechanism cover base, rocker arms and shafts. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety notices are provided to keep parts clean and prevent contamination.
This document provides instructions for removing and installing various components of a C13 Industrial Engine, including the valve mechanism cover base, rocker arm and shaft, rocker arm, cylinder head, lifter group, and camshaft. The procedures include illustrations of the components and steps to disconnect harness assemblies, remove bolts, and lift components out of the engine. Safety precautions and notes about component weights and lubrication are also provided.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
More Related Content
Similar to Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ00001 and up).pdf
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive, which involves removing pulleys, gears, bearings, seals, and other components.
2) Removing and installing the valve mechanism cover and valve mechanism cover base, which connect to the cylinder head.
3) Removing the rocker arm and shaft assembly, which controls the valves.
4) Disassembling the rocker arm, including removing adjustment screws and seals.
The document contains detailed step-by-step instructions accompanied by illustrations and lists of required tools for each procedure. Safety notices are provided to keep parts clean and prevent damage.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive, which involves removing pulleys, gears, bearings, seals, and other components.
2) Removing and installing the valve mechanism cover and valve mechanism cover base, which connect to the cylinder head.
3) Removing the rocker arm and shaft assembly, which controls the valves.
4) Disassembling the rocker arm, involving removing adjustment screws and other small parts.
The document contains detailed step-by-step instructions accompanied by illustrations and lists of required tools for each procedure. Safety notices are provided to keep parts clean and prevent
This document provides instructions for servicing components of a C27 Industrial Engine, including:
- Disassembling and assembling the auxiliary drive (front).
- Removing and installing the valve mechanism cover and valve mechanism cover base.
- Removing the rocker arm and shaft assembly.
- Disassembling and assembling the rocker arms.
The summaries provide the essential steps and components for each service procedure in 3 sentences or less.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine. It describes how to remove and install the auxiliary drive, valve mechanism covers, valve mechanism cover base, rocker arms and shafts. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety notices are provided to keep parts clean and prevent contamination.
This document provides instructions for removing and installing various components of a C13 Industrial Engine, including the valve mechanism cover base, rocker arm and shaft, rocker arm, cylinder head, lifter group, and camshaft. The procedures include illustrations of the components and steps to disconnect harness assemblies, remove bolts, and lift components out of the engine. Safety precautions and notes about component weights and lubrication are also provided.
Similar to Caterpillar Cat C13 Industrial Engine (Prefix KWJ) Service Repair Manual (KWJ00001 and up).pdf (14)
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03551630
Camshaft - Install
SMCS - 1210-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7638 Magnetic Holding Tool 18
B
201-4211 Camshaft Pilot 1
201-4212 Camshaft Pilot 1
1/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01292428
1. Install Tooling (B).
Note: Ensure that camshaft (6) and Tooling (B) are clean. Apply clean engine oil to the
lobes and journals of camshaft (6) and Tooling (B).
Note: During installation of camshaft (6), rotate the camshaft in both directions in order to
prevent binding in the camshaft bearing bores.
2. Carefully install camshaft (6) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01292427
3. Ensure that the timing Marks (X) on the idler gear aligned with the timing marks on the
crankshaft gear and the camshaft drive gear.
4. Remove Tooling (A) and Tooling (B).
Illustration 3 g01878141
5. Install cover (2). Install hose assembly (3) and tube assembly (4).
3/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 4 g01011039
6. Install bolts (1).
End By:
a. Install the camshaft position sensor.
b. Install the front cover.
c. Install the rocker arm and shaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:06:17 UTC+0800 2020
4/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i04587192
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
A. Remove the camshaft.
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00522082
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. NOTICE
Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove drive gear (1) from camshaft (3) .
3. Remove woodruff key (2) .
Installation Procedure
Illustration 2 g00522082
1. Install woodruff key (2) in camshaft (3) .
2. Raise the temperature of drive gear (1) to a temperature of 315° C (600° F).
3. Install drive gear (1) on the end of camshaft (3) .
End By: Install the camshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:07:12 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03551900
Camshaft Bearings - Remove
SMCS - 1211-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
201-4214 Receiving Sleeve 1
201-4213 Puller Plate 1
201-4209 Bearing Pilot 1
201-4208 Backup Plate 1
6F-7032 Bolt 1
8M-8778 Taperlock Stud 1
8S-8292 Extension (Short) 2
8S-8293 Extension (Long) 1
B 185-3989 Thread Lubricant 1
Start By:
a. Remove the lifter group.
b. Remove the camshaft.
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g01016694
1. Install Tooling (A). Apply Tooling (B) on the threads.
2. Remove camshaft bearings (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:08:08 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03551921
Camshaft Bearings - Install
SMCS - 1211-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
201-4214 Receiving Sleeve 1
201-4213 Puller Plate 1
201-4209 Bearing Pilot 1
201-4208 Backup Plate 1
6F-7032 Bolt 1
8M-8778 Taperlock Stud 1
8S-8292 Extension (Short) 2
8S-8293 Extension (Long) 1
1/3(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g01133376
1. Position new camshaft bearing (1) in Tooling (A) and install the bearing from the rear to the
front of the engine.
Illustration 2 g01133395
2. The camshaft bearings are installed with Tooling (A). Measure the depth of the camshaft
bearings from the front face of the cylinder block to the following distances:
a. Dimension (A) is 36.50 mm (1.437 inch).
b. Dimension (B) is 192.50 mm (7.579 inch).
c. Dimension (C) is 348.50 mm (13.720 inch).
d. Dimension (D) is 504.50 mm (19.862 inch).
2/3(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. e. Dimension (E) is 660.50 mm (26.004 inch).
f. Dimension (F) is 816.50 mm (32.146 inch).
g. Dimension (G) is 972.50 mm (38.287 inch).
NOTICE
Camshaft bearings must be installed into their correct position. Failure
to do so will result in engine damage.
Illustration 3 g01133403
(2) Bearing joint
(3) Oil hole
(H) Bearing oil hole is located at a 45 degree angle from vertical. All seven bearings have the
same angle.
End By:
a. Install the camshaft.
b. Install the lifter group.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:09:04 UTC+0800 2020
3/3(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i04970472
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 596 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil into a suitable container. Refer to Operation and Maintenance Manual, "Refill
Capacities and Recommendations".
1/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g02466033
2. Remove bolts (1), washers (2), fastener assemblies (3) and remove oil pan (4) .
Installation Procedure
Illustration 2 g02466177
Note: Ensure that the oil pan and mating surfaces are clean and free of oil.
1. Apply Tooling (A) at four locations marked (A). Tooling (A) should be applied in 4 ± 1 mm
(0.16 ± 0.04 inch) diameter beads.
Note: All joints using Tooling (A) must be assembled within ten minutes of the application.
2/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g02466556
2. Install fastener assemblies (3) and the gasket (not shown) onto oil pan (4) .
Illustration 4 g02466576
Illustration 5 g02466597
Torque Sequence
3. Position oil pan (4), washers (2), and bolts (1) into place.
3/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 4. Tighten bolts (1) in the above sequence.
5. Fill the engine with oil. Refer to Operation and Maintenance Manual, "Refill Capacities and
Recommendations".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:10:00 UTC+0800 2020
4/4(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03551963
Cylinder Liner - Remove
SMCS - 1216-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-8665 Cylinder Liner Puller Gp 1
Start By:
a. Remove the pistons and the connecting rods.
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g01005579
1. Use Tooling (A) to remove cylinder liner (1).
2. Remove the O-ring seals from cylinder liner (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:10:55 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03551988
Cylinder Liner - Install
SMCS - 1216-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 2P-8260 Cylinder Liner Installer 1
C 5P-3975 Rubber Lubricant 1
Illustration 1 g01133518
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 1. Install the O-ring seals on cylinder liner (1).
2. Apply Tooling (C) on the O-ring seals.
Note: Refer to Testing and Adjusting, "Cylinder Liner Projection" for more information.
Note: If you are installing a cylinder pack, ensure that the corresponding crankshaft throw is
at bottom center.
3. Use Tooling (B) to install cylinder liner (1).
End By:
a. Install the pistons and the connecting rods.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:11:51 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03554761
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan.
NOTICE
Special care must be taken not to bend the piston cooling jets because
the piston cooling jets are precision aligned with a coolant passage in
the pistons.
There is only one position for each cooling jet. The notch in the bottom
of the piston allows clearance for the piston cooling jet when the piston
is at bottom dead center.
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 1 g01133547
1. Remove bolt (1) and piston cooling jet (2).
Installation Procedure
1. Install piston cooling jet (2) in reverse order of removal.
a. Tighten bolt (1) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:12:47 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C13 INDUSTRIAL ENGINE KWJ
Configuration: C13 Industrial Engine KWJ00001-UP
Disassembly and Assembly
C13 Engine and C13 Industrial Engine
Media Number -KENR8165-03 Publication Date -01/11/2017 Date Updated -14/11/2017
i03554787
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Start By:
a. Remove the cylinder head.
b. Remove the engine oil pan.
Illustration 1 g01268763
1. Place an identification mark on the connecting rod and connecting rod cap (2). The number
should match the cylinder number. The bearing retainer notch should be on the right side.
1/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 2. Remove connecting rod cap (2). Remove the lower half of connecting rod bearing (1) from
connecting rod cap (2).
3. Push the piston and connecting rod away from the crankshaft. Remove the upper half of the
connecting rod bearing.
Note: Careful handling is required for fractured connecting rods. Fractured faces for the
connecting rod and connecting rod cap should not be placed on any surface. The connecting
rod and the connecting rod cap should be placed on the sides in order to prevent damage.
When possible, the connecting rod and the connecting rod cap should be bolted together in
order to prevent damage.
4. Remove the piston and connecting rod from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 23:13:42 UTC+0800 2020
2/2(W)
w
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...