The document appears to contain test results from a protection relay for a power transformer. It includes settings for the test object which is a transformer, nominal voltage and current values, test signals applied for different fault types and phases, and assessment of the test results showing the protection relay operated as expected for internal faults on the transformer.
The document summarizes relay protection testing performed at the CH Restitucion substation. Tests were conducted on the 110Vcc and 48Vcc circuit relays and auxiliary service relays. The tests included ramp, timing, and operation tests to verify the correct pickup values and time delays. Test reports provide details of the test configurations, parameters, results and evaluations for each relay tested. Sign off was obtained from the test executor, EDP specialist and Electroperu supervisor to approve the tests.
This document contains test protocols and results for protection relays of Generation Unit 1 at the CH Restitution power plant. It provides details of impedance testing and timing tests conducted on the 21G-R and 21G-S relays, including test configurations, element settings, and evaluation of test results. Sign-off was provided by three parties approving, conditionally approving, or not approving the tests and their results.
Original Digital Transistor KRC105 C105M C105 100mA 50V TO-92 NewAUTHELECTRONIC
This document provides specifications for 6 types of epitaxial planar NPN transistors (KRC101-KRC106). The transistors have built-in bias resistors to simplify circuit design. Key specifications include maximum voltage and current ratings, electrical characteristics like DC current gain and switching times, and I-V and G-I curves showing performance over temperature ranges.
Original NPN Transistor KRC106M C106 106 TO-92 New KECAUTHELECTRONIC
This document provides specifications for 6 types of epitaxial planar NPN transistors (KRC101-KRC106). The transistors have built-in bias resistors to simplify circuit design. Key specifications include maximum voltage and current ratings, electrical characteristics like DC current gain and switching times, and I-V and G-I curves showing performance over temperature ranges.
Original Transistor NPN MPSA18 MPS A18 TO 92 New ONauthelectroniccom
This document provides specifications for the MPSA18 low noise transistor, including:
1) Maximum ratings for voltage, current, and temperature parameters.
2) Typical electrical characteristics such as gain, voltage, and capacitance.
3) Noise characteristics including noise voltage, current, and figures across frequency ranges.
4) Package dimensions and ordering information for the TO-92 packaged transistor.
The document summarizes relay protection testing performed at the CH Restitucion substation. Tests were conducted on the 110Vcc and 48Vcc circuit relays and auxiliary service relays. The tests included ramp, timing, and operation tests to verify the correct pickup values and time delays. Test reports provide details of the test configurations, parameters, results and evaluations for each relay tested. Sign off was obtained from the test executor, EDP specialist and Electroperu supervisor to approve the tests.
This document contains test protocols and results for protection relays of Generation Unit 1 at the CH Restitution power plant. It provides details of impedance testing and timing tests conducted on the 21G-R and 21G-S relays, including test configurations, element settings, and evaluation of test results. Sign-off was provided by three parties approving, conditionally approving, or not approving the tests and their results.
Original Digital Transistor KRC105 C105M C105 100mA 50V TO-92 NewAUTHELECTRONIC
This document provides specifications for 6 types of epitaxial planar NPN transistors (KRC101-KRC106). The transistors have built-in bias resistors to simplify circuit design. Key specifications include maximum voltage and current ratings, electrical characteristics like DC current gain and switching times, and I-V and G-I curves showing performance over temperature ranges.
Original NPN Transistor KRC106M C106 106 TO-92 New KECAUTHELECTRONIC
This document provides specifications for 6 types of epitaxial planar NPN transistors (KRC101-KRC106). The transistors have built-in bias resistors to simplify circuit design. Key specifications include maximum voltage and current ratings, electrical characteristics like DC current gain and switching times, and I-V and G-I curves showing performance over temperature ranges.
Original Transistor NPN MPSA18 MPS A18 TO 92 New ONauthelectroniccom
This document provides specifications for the MPSA18 low noise transistor, including:
1) Maximum ratings for voltage, current, and temperature parameters.
2) Typical electrical characteristics such as gain, voltage, and capacitance.
3) Noise characteristics including noise voltage, current, and figures across frequency ranges.
4) Package dimensions and ordering information for the TO-92 packaged transistor.
This document summarizes the testing and calibration of protection relays for Generator 2 at the CH Restitucion power plant. It details 13 different protection relay tests, including tests for minimum impedance, loss of excitation, reverse power, overvoltage, ground fault, thermal, and overcurrent relays. The tests were performed on November 30, 2019 by technicians from Electroperu and were supervised by engineers from Estudios Supervision. All relays passed testing.
Original N-Channel Mosfet IRFB3077PBF IRFB3077 3077 75V 120A TO-220 New IRAUTHELECTRONIC
Original N-Channel Mosfet IRFB3077PBF IRFB3077 3077 75V 120A TO-220 New IR
https://authelectronic.com/original-n-channel-mosfet-irfb3077pbf-irfb3077-3077-75v-120a-to-220-new-ir
This document provides specifications for the BC337, BC337-25, and BC337-40 NPN silicon amplifier transistors. It includes maximum ratings, electrical characteristics, ordering information, and package dimensions. The transistors can handle currents up to 800mA and have DC current gains from 100-630 depending on the model. Thermal and electrical performance graphs are provided. The devices come in TO-92 plastic packages and are Pb-free.
This document provides specifications for the BC337, BC337-25, and BC337-40 NPN silicon amplifier transistors. It includes maximum ratings, electrical characteristics, ordering information, and package dimensions. The transistors can handle currents up to 800mA and have DC current gains from 100-630 depending on the model. Thermal and electrical performance graphs are provided. The devices come in TO-92 plastic packages and are RoHS-compliant Pb-free.
Original N-Channel Mosfet CS13N50 13N50 500V 13A TO-220 NewAUTHELECTRONIC
The document provides specifications for the CS13N50 A8H silicon N-channel power MOSFET, including its electrical characteristics, thermal properties, maximum ratings and applications. Key features include low on-resistance, fast switching speeds, and high single pulse avalanche energy rating. The MOSFET is intended for use in power switching circuits for applications such as adaptor and charger power switches.
Original Thyristor TYN825RG 825 25A 800V TO-220 New STMicroelectronicsAUTHELECTRONIC
Original Thyristor TYN825RG 825 25A 800V TO-220 New STMicroelectronics
https://authelectronic.com/original-thyristor-tyn825rg-tny825-25a-800v-to-220-new-stmicroelectronics
katalog agilent-34420 a-micro-ohm-meter-tridinamika, jual agilent 34420 a micro ohm meter, beli, info, harga, spesifikasi dan review
Dapatkan informasi lengkap tentang produk agilent di www.tridinamika.com
untuk informasi dan pemesanan hubungi sales@tridinamika.com
This document provides the results of relay protection testing conducted on the generators and transformers at the CH Restitucion power plant. It details the testing of 13 different relays for Generator 3, including relays for minimum impedance, loss of excitation, reverse power, overvoltage, ground fault, thermal overload, and negative sequence current. For each relay, it lists the test configuration, measurements taken during testing against expected thresholds, and whether the relay passed or failed each test. The tests were approved by three signatories on November 24, 2019.
Original PNP Transistor 327 BC32 BC327-025G TO-92 New ON semiconductorAUTHELECTRONIC
This document provides information on a series of PNP silicon amplifier transistors (BC327, BC327-16, BC327-25, BC327-40) from ON Semiconductor, including:
- Maximum ratings and characteristics like collector-emitter voltage, power dissipation, and thermal resistance.
- Electrical characteristics in active, saturation, and cutoff regions including current gain, voltage, and capacitance.
- Ordering information and package dimensions for the TO-92 package type.
- Graphs of characteristics like safe operating area, current gain vs. collector current, and capacitance vs. voltage/current.
This document provides specifications for Powerex's Dual SCR Isolated Module, model LDR3__50. It is a 500 ampere module that operates between 800-1800 volts. The document includes ordering information, outline drawings, electrical and thermal characteristics, and application information. It specifies the module's voltage and current ratings, dimensions, connection terminals, and that it is UL recognized.
This document provides specifications for Powerex's Dual SCR Isolated Module, model LDR3__50. It is a 500 ampere module that operates between 800-1800 volts. The document includes ordering information, outline drawings, electrical and thermal characteristics, application information, and notes on included lead kits. It allows for isolated mounting and mounting on a common heatsink.
Original N-Channel Mosfet PFF7N80 800V 7A TO-220F New WING ON GROUPAUTHELECTRONIC
This document describes the PFP7N80/PFF7N80 800V N-channel MOSFETs from Wing On STS. Key specifications include a continuous drain current of 7A, on-resistance of 1.55Ω typical, and gate charge of 35nC typical. The document provides detailed electrical characteristics, thermal characteristics, application information, and test methodology for the devices.
Original IGBT IRGP4068DPBF GP4068D 4068 600V 96A 330W TO-247 New Infineonauthelectroniccom
This document provides specifications for an insulated gate bipolar transistor (IGBT) with an ultra-low voltage drop diode for induction heating and soft switching applications. The IGBT has a maximum collector-emitter voltage of 600V, continuous collector current of 48A at 100°C junction temperature, and features low switching losses, high efficiency, and robust performance under transient conditions. The integrated ultra-low voltage drop diode provides tight parameter distribution and low forward voltage for increased efficiency.
Original IGBT Transistor GT60N322 60N322 N322 322 57A 1000V TO-3P New ToshibaAUTHELECTRONIC
This document provides specifications for the TOSHIBA Insulated Gate Bipolar Transistor Silicon N Channel IGBT GT60N322. Key details include:
- It is an enhancement mode IGBT with high speed (turn-off time of 0.11 μs) and low saturation voltage (2.4 V typical at 60 A collector current).
- It has a maximum collector-emitter voltage of 1000 V, collector current of 57 A continuous and 120 A pulsed. Junction temperature can reach 150°C.
- Electrical characteristics are provided including input capacitance, rise/fall times, switching times, forward voltage, and reverse recovery time.
- Thermal and safe operating characteristics
Original IGBT IRG4BC20KD G4BC20KD 600V 9A TO-220 NewAUTHELECTRONIC
This document provides specifications for an insulated gate bipolar transistor (IGBT) with an integrated ultrafast soft recovery diode. It lists maximum ratings, electrical characteristics, switching characteristics, and thermal characteristics for the device. Key parameters include a collector-emitter voltage of 600V, continuous collector current ratings of 16A and 9A, and ultrafast switching times below 100ns. Graphs illustrate characteristics such as output curves, gate charge, and switching losses. The document also contains a test circuit diagram and waveform definitions for evaluating the device performance.
This document summarizes the testing and calibration of protection relays for Generator 2 at the CH Restitucion power plant. It details 13 different protection relay tests, including tests for minimum impedance, loss of excitation, reverse power, overvoltage, ground fault, thermal, and overcurrent relays. The tests were performed on November 30, 2019 by technicians from Electroperu and were supervised by engineers from Estudios Supervision. All relays passed testing.
Original N-Channel Mosfet IRFB3077PBF IRFB3077 3077 75V 120A TO-220 New IRAUTHELECTRONIC
Original N-Channel Mosfet IRFB3077PBF IRFB3077 3077 75V 120A TO-220 New IR
https://authelectronic.com/original-n-channel-mosfet-irfb3077pbf-irfb3077-3077-75v-120a-to-220-new-ir
This document provides specifications for the BC337, BC337-25, and BC337-40 NPN silicon amplifier transistors. It includes maximum ratings, electrical characteristics, ordering information, and package dimensions. The transistors can handle currents up to 800mA and have DC current gains from 100-630 depending on the model. Thermal and electrical performance graphs are provided. The devices come in TO-92 plastic packages and are Pb-free.
This document provides specifications for the BC337, BC337-25, and BC337-40 NPN silicon amplifier transistors. It includes maximum ratings, electrical characteristics, ordering information, and package dimensions. The transistors can handle currents up to 800mA and have DC current gains from 100-630 depending on the model. Thermal and electrical performance graphs are provided. The devices come in TO-92 plastic packages and are RoHS-compliant Pb-free.
Original N-Channel Mosfet CS13N50 13N50 500V 13A TO-220 NewAUTHELECTRONIC
The document provides specifications for the CS13N50 A8H silicon N-channel power MOSFET, including its electrical characteristics, thermal properties, maximum ratings and applications. Key features include low on-resistance, fast switching speeds, and high single pulse avalanche energy rating. The MOSFET is intended for use in power switching circuits for applications such as adaptor and charger power switches.
Original Thyristor TYN825RG 825 25A 800V TO-220 New STMicroelectronicsAUTHELECTRONIC
Original Thyristor TYN825RG 825 25A 800V TO-220 New STMicroelectronics
https://authelectronic.com/original-thyristor-tyn825rg-tny825-25a-800v-to-220-new-stmicroelectronics
katalog agilent-34420 a-micro-ohm-meter-tridinamika, jual agilent 34420 a micro ohm meter, beli, info, harga, spesifikasi dan review
Dapatkan informasi lengkap tentang produk agilent di www.tridinamika.com
untuk informasi dan pemesanan hubungi sales@tridinamika.com
This document provides the results of relay protection testing conducted on the generators and transformers at the CH Restitucion power plant. It details the testing of 13 different relays for Generator 3, including relays for minimum impedance, loss of excitation, reverse power, overvoltage, ground fault, thermal overload, and negative sequence current. For each relay, it lists the test configuration, measurements taken during testing against expected thresholds, and whether the relay passed or failed each test. The tests were approved by three signatories on November 24, 2019.
Original PNP Transistor 327 BC32 BC327-025G TO-92 New ON semiconductorAUTHELECTRONIC
This document provides information on a series of PNP silicon amplifier transistors (BC327, BC327-16, BC327-25, BC327-40) from ON Semiconductor, including:
- Maximum ratings and characteristics like collector-emitter voltage, power dissipation, and thermal resistance.
- Electrical characteristics in active, saturation, and cutoff regions including current gain, voltage, and capacitance.
- Ordering information and package dimensions for the TO-92 package type.
- Graphs of characteristics like safe operating area, current gain vs. collector current, and capacitance vs. voltage/current.
This document provides specifications for Powerex's Dual SCR Isolated Module, model LDR3__50. It is a 500 ampere module that operates between 800-1800 volts. The document includes ordering information, outline drawings, electrical and thermal characteristics, and application information. It specifies the module's voltage and current ratings, dimensions, connection terminals, and that it is UL recognized.
This document provides specifications for Powerex's Dual SCR Isolated Module, model LDR3__50. It is a 500 ampere module that operates between 800-1800 volts. The document includes ordering information, outline drawings, electrical and thermal characteristics, application information, and notes on included lead kits. It allows for isolated mounting and mounting on a common heatsink.
Original N-Channel Mosfet PFF7N80 800V 7A TO-220F New WING ON GROUPAUTHELECTRONIC
This document describes the PFP7N80/PFF7N80 800V N-channel MOSFETs from Wing On STS. Key specifications include a continuous drain current of 7A, on-resistance of 1.55Ω typical, and gate charge of 35nC typical. The document provides detailed electrical characteristics, thermal characteristics, application information, and test methodology for the devices.
Original IGBT IRGP4068DPBF GP4068D 4068 600V 96A 330W TO-247 New Infineonauthelectroniccom
This document provides specifications for an insulated gate bipolar transistor (IGBT) with an ultra-low voltage drop diode for induction heating and soft switching applications. The IGBT has a maximum collector-emitter voltage of 600V, continuous collector current of 48A at 100°C junction temperature, and features low switching losses, high efficiency, and robust performance under transient conditions. The integrated ultra-low voltage drop diode provides tight parameter distribution and low forward voltage for increased efficiency.
Original IGBT Transistor GT60N322 60N322 N322 322 57A 1000V TO-3P New ToshibaAUTHELECTRONIC
This document provides specifications for the TOSHIBA Insulated Gate Bipolar Transistor Silicon N Channel IGBT GT60N322. Key details include:
- It is an enhancement mode IGBT with high speed (turn-off time of 0.11 μs) and low saturation voltage (2.4 V typical at 60 A collector current).
- It has a maximum collector-emitter voltage of 1000 V, collector current of 57 A continuous and 120 A pulsed. Junction temperature can reach 150°C.
- Electrical characteristics are provided including input capacitance, rise/fall times, switching times, forward voltage, and reverse recovery time.
- Thermal and safe operating characteristics
Original IGBT IRG4BC20KD G4BC20KD 600V 9A TO-220 NewAUTHELECTRONIC
This document provides specifications for an insulated gate bipolar transistor (IGBT) with an integrated ultrafast soft recovery diode. It lists maximum ratings, electrical characteristics, switching characteristics, and thermal characteristics for the device. Key parameters include a collector-emitter voltage of 600V, continuous collector current ratings of 16A and 9A, and ultrafast switching times below 100ns. Graphs illustrate characteristics such as output curves, gate charge, and switching losses. The document also contains a test circuit diagram and waveform definitions for evaluating the device performance.
Building a Raspberry Pi Robot with Dot NET 8, Blazor and SignalR - Slides Onl...Peter Gallagher
In this session delivered at Leeds IoT, I talk about how you can control a 3D printed Robot Arm with a Raspberry Pi, .NET 8, Blazor and SignalR.
I also show how you can use a Unity app on an Meta Quest 3 to control the arm VR too.
You can find the GitHub repo and workshop instructions here;
https://bit.ly/dotnetrobotgithub
1. PRUEBAS SAT
SEL 487E-3
.
.
Test Object - Device Settings
. . .
Substation/Bay:
Substation: SET SAN LUIS Substation address: SELVA ALEGRE - AREQUIPA
Bay: TRANSFORMADOR Bay address: =E00+R00
. . .
Device:
Name/description: SEL 487E 3 Manufacturer: SEL
Device type: DIFERENCIAL TRAFO Device address: =E00+R00
Serial/model number: 1221757137
Additional info 1: SEL-487E-3-R321-V0
Additional info 2: SEL PERU SAC
. . .
Nominal Values:
f nom: 60.00 Hz Number of phases: 3
V nom (secondary): 100.0 V V primary: 33.50 kV
I nom (secondary): 5.000 A I primary: 800.0 A
. . .
Residual Voltage/Current Factors:
VLN / VN: 1.000 IN / I nom: 1.000
VN (secondary): 57.74 V IN (secondary): 5.000 A
Residual Voltage
Direction:
3 * V0 Residual Current Direction: -3 * I0
. . .
Limits:
V max: 200.0 V I max: 50.00 A
. . .
Debounce/Deglitch Filters:
Debounce time: 3.000 ms Deglitch time: 0.00 s
. . .
Overload Detection:
Suppression time: 50.00 ms
. . .
Other Device Properties:
Drop-out time: 20.00 ms
4. Trip time 87T Fault A-B-C:
.
Test Settings
State Pre Fault Fault Transition
State
Post Fault
I W1 A 0.00 A 3.000 A 0.00 A 0.00 A
0.00 ° 0.00 ° 0.00 ° 0.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W1 B 0.00 A 3.000 A 0.00 A 0.00 A
-120.00 ° -120.00 ° -120.00 ° -120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W1 C 0.00 A 3.000 A 0.00 A 0.00 A
120.00 ° 120.00 ° 120.00 ° 120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 A 0.00 A 0.00 A 0.00 A 0.00 A
0.00 ° 0.00 ° 0.00 ° 0.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 B 0.00 A 0.00 A 0.00 A 0.00 A
-120.00 ° -120.00 ° -120.00 ° -120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 C 0.00 A 0.00 A 0.00 A 0.00 A
120.00 ° 120.00 ° 120.00 ° 120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
Max. State Time 60.00 cy 4.167 cy 1.000 cy 60.00 cy
Trigger Logic OR OR
Trip 1 Lado 33kV 1 0
Trip 2 Lado 33kV 1 0
User interaction no no no no
CMGPS trigger no no no no
IRIG-B/PTP triggerno no no no
Pulses / seconds 1 1 1 1
Delay after Tr. 0.00 cy 0.00 cy 0.00 cy 0.00 cy
On trigger jump to
test end
no no no no
Diagrams
Comment
. .
Test Module
Name: OMICRON State Sequencer Version: 4.31
Test Start: 11-May-2023 10:24:27 Test End: 11-May-2023 10:24:31
User Name: Manager:
Company:
Test Results
.
Time Assessment
Name Ignore
before
Start Stop Tnom Tdev- Tdev+ Tact Tdev Assess
Trip Time Fault Fault Trip 1 Lado
33kV 0>1
2.000 cy 0.3000 cy 0.3000 cy 2.250 cy 0.2520 cy +
Assess: + .. Passed x .. Failed o .. Not assessed
. . . . .
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
5. State
Assessment
Pre Fault Fault Transition
State
Post Fault
Assess o o + o
Tolerance 0.00 cy 0.00 cy 0.1000 cy 0.00 cy
Trip 1 Lado 33kV X X 1 X
Trip 2 Lado 33kV X X 1 X
Assess: + .. Passed x .. Failed o .. Not assessed
.
Cursor Data
Time Signal Value
Cursor 1 0.00 s <none> n/a
Cursor 2 123.25 s <none> n/a
C2 - C1 123.25 s n/a
6. .
Event recorder
Time Type Signal name Slope
62.25 cy Input Trip 1 Lado 33kV 0>1
62.25 cy Input Trip 2 Lado 33kV 0>1
62.25 cy Input Trip 1 Lado 10kV 0>1
67.72 cy Input Trip 1 Lado 33kV 1>0
67.72 cy Input Trip 2 Lado 33kV 1>0
67.72 cy Input Trip 1 Lado 10kV 1>0
.
Test State:
Test passed
Trip time 87T Fault A-N:
.
Test Settings
State Pre Fault Fault Transition
State
Post Fault
I W1 A 0.00 A 3.000 A 0.00 A 0.00 A
0.00 ° 0.00 ° 0.00 ° 0.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W1 B 0.00 A 0.00 A 0.00 A 0.00 A
-120.00 ° -120.00 ° -120.00 ° -120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W1 C 0.00 A 0.00 A 0.00 A 0.00 A
120.00 ° 120.00 ° 120.00 ° 120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 A 0.00 A 0.00 A 0.00 A 0.00 A
0.00 ° 0.00 ° 0.00 ° 0.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 B 0.00 A 0.00 A 0.00 A 0.00 A
-120.00 ° -120.00 ° -120.00 ° -120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
I W2 C 0.00 A 0.00 A 0.00 A 0.00 A
120.00 ° 120.00 ° 120.00 ° 120.00 °
60.000 Hz 60.000 Hz 60.000 Hz 60.000 Hz
Max. State Time 60.00 cy 4.167 cy 1.000 cy 60.00 cy
Trigger Logic OR OR
Trip 1 Lado 33kV 1 0
Trip 2 Lado 33kV 1 0
User interaction no no no no
CMGPS trigger no no no no
IRIG-B/PTP triggerno no no no
Pulses / seconds 1 1 1 1
Delay after Tr. 0.00 cy 0.00 cy 0.00 cy 0.00 cy
On trigger jump to
test end
no no no no
Diagrams
Comment
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
+90°
-90°
180° 0°
32.0 A
7. . .
Test Module
Name: OMICRON State Sequencer Version: 4.31
Test Start: 11-May-2023 10:16:00 Test End: 11-May-2023 10:16:04
User Name: Manager:
Company:
Test Results
.
Time Assessment
Name Ignore
before
Start Stop Tnom Tdev- Tdev+ Tact Tdev Assess
Trip Time Fault Fault Trip 1 Lado
33kV 0>1
2.000 cy 0.3000 cy 0.3000 cy 2.172 cy 0.1740 cy +
Assess: + .. Passed x .. Failed o .. Not assessed
. . . . .
State
Assessment
Pre Fault Fault Transition
State
Post Fault
Assess o o + o
Tolerance 0.00 cy 0.00 cy 0.1000 cy 0.00 cy
Trip 1 Lado 33kV X X 1 X
Trip 2 Lado 33kV X X 1 X
Assess: + .. Passed x .. Failed o .. Not assessed
8. .
Cursor Data
Time Signal Value
Cursor 1 0.00 s <none> n/a
Cursor 2 123.17 s <none> n/a
C2 - C1 123.17 s n/a
.
Event recorder
Time Type Signal name Slope
62.17 cy Input Trip 1 Lado 33kV 0>1
62.17 cy Input Trip 2 Lado 33kV 0>1
62.17 cy Input Trip 1 Lado 10kV 0>1
67.66 cy Input Trip 1 Lado 33kV 1>0
67.66 cy Input Trip 2 Lado 33kV 1>0
67.67 cy Input Trip 1 Lado 10kV 1>0
.
.
Test State:
Test passed
9. External Fault A-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
Graph:
Single Line View for Protected Object (YD11)
D11
Y
Supply
L1-E
10. . .
Test Module
Name: OMICRON Diff Configuration Version: 4.31
Test Start: 11-May-2023 10:22:58 Test End: 11-May-2023 10:23:22
User Name: Manager:
Company:
.
Test Settings
Test time: 60 s Apply Load Current: No
Load Side: n/a Load Current: 0.00 In
Fault Side: Winding S Supply Side: Winding W
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
. . . .
Binary Outputs
Test Results for Fault Type L1-E at Fault Location Winding S
. . .
ITest = 1.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 2.69A -180.0° 0.000A 0.000° 2.60A 0.0° 0.000A 0.000° n/a n/a n/a n/a
B 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 0.00A 0.0° 0.000A 0.000° 2.60A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 2.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 5.39A -180.0° 0.000A 0.000° 5.21A 0.0° 0.000A 0.000° n/a n/a n/a n/a
B 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 0.00A 0.0° 0.000A 0.000° 5.21A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 3.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 8.08A -180.0° 0.000A 0.000° 7.81A 0.0° 0.000A 0.000° n/a n/a n/a n/a
B 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 0.00A 0.0° 0.000A 0.000° 7.81A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 4.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
11. Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 10.77A -180.0° 0.000A 0.000° 10.42A 0.0° 0.000A 0.000° n/a n/a n/a n/a
B 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 0.00A 0.0° 0.000A 0.000° 10.42A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 5.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 13.46A -180.0° 0.000A 0.000° 13.02A 0.0° 0.000A 0.000° n/a n/a n/a n/a
B 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 0.00A 0.0° 0.000A 0.000° 13.02A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
.
Test State:
Test passed
5 out of 5 points tested.
5 points passed. 0
points failed.
External Fault B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
12. Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
Graph:
. .
Test Module
Name: OMICRON Diff Configuration Version: 4.31
Test Start: 11-May-2023 11:21:13 Test End: 11-May-2023 11:21:25
User Name: Manager:
Company:
.
Test Settings
Test time: 60 s Apply Load Current: No
Load Side: n/a Load Current: 0.00 In
Fault Side: Winding S Supply Side: Winding W
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
. . . .
Binary Outputs
Test Results for Fault Type L2-L3 at Fault Location Winding S
. . .
ITest = 1.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 0.00A 0.0° 0.000A 0.000° 2.60A 180.0° 0.000A 0.000° n/a n/a n/a n/a
B 2.69A -180.0° 0.000A 0.000° 5.21A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 2.69A 0.0° 0.000A 0.000° 2.60A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Single Line View for Protected Object (YD11)
D11
Y
Supply
L2-L3
13. Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 2.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 0.00A 0.0° 0.000A 0.000° 5.21A 180.0° 0.000A 0.000° n/a n/a n/a n/a
B 5.39A -180.0° 0.000A 0.000° 10.42A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 5.39A 0.0° 0.000A 0.000° 5.21A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 3.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 0.00A 0.0° 0.000A 0.000° 7.81A 180.0° 0.000A 0.000° n/a n/a n/a n/a
B 8.08A -180.0° 0.000A 0.000° 15.63A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 8.08A 0.0° 0.000A 0.000° 7.81A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 4.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 0.00A 0.0° 0.000A 0.000° 10.42A 180.0° 0.000A 0.000° n/a n/a n/a n/a
B 10.77A -180.0° 0.000A 0.000° 20.83A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 10.77A 0.0° 0.000A 0.000° 10.42A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 5.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 0.00A 0.0° 0.000A 0.000° 13.02A 180.0° 0.000A 0.000° n/a n/a n/a n/a
B 13.46A -180.0° 0.000A 0.000° 26.04A 0.0° 0.000A 0.000° n/a n/a n/a n/a
C 13.46A 0.0° 0.000A 0.000° 13.02A 180.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
.
Test State:
Test passed
5 out of 5 points tested.
5 points passed. 0
points failed.
14. External Fault A-B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
Graph:
Single Line View for Protected Object (YD11)
D11
Y
Supply
L1-L2-L3
15. . .
Test Module
Name: OMICRON Diff Configuration Version: 4.31
Test Start: 11-May-2023 11:21:39 Test End: 11-May-2023 11:21:54
User Name: Manager:
Company:
.
Test Settings
Test time: 60 s Apply Load Current: No
Load Side: n/a Load Current: 0.00 In
Fault Side: Winding S Supply Side: Winding W
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
. . . .
Binary Outputs
Test Results for Fault Type L1-L2-L3 at Fault Location Winding S
. . .
ITest = 1.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 2.69A -180.0° 0.000A 0.000° 4.51A 30.0° 0.000A 0.000° n/a n/a n/a n/a
B 2.69A 60.0° 0.000A 0.000° 4.51A -90.0° 0.000A 0.000° n/a n/a n/a n/a
C 2.69A -60.0° 0.000A 0.000° 4.51A 150.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 2.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 5.39A -180.0° 0.000A 0.000° 9.02A 30.0° 0.000A 0.000° n/a n/a n/a n/a
B 5.39A 60.0° 0.000A 0.000° 9.02A -90.0° 0.000A 0.000° n/a n/a n/a n/a
C 5.39A -60.0° 0.000A 0.000° 9.02A 150.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 3.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 8.08A -180.0° 0.000A 0.000° 13.53A 30.0° 0.000A 0.000° n/a n/a n/a n/a
B 8.08A 60.0° 0.000A 0.000° 13.53A -90.0° 0.000A 0.000° n/a n/a n/a n/a
C 8.08A -60.0° 0.000A 0.000° 13.53A 150.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 4.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
16. Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 10.77A -180.0° 0.000A 0.000° 18.04A 30.0° 0.000A 0.000° n/a n/a n/a n/a
B 10.77A 60.0° 0.000A 0.000° 18.04A -90.0° 0.000A 0.000° n/a n/a n/a n/a
C 10.77A -60.0° 0.000A 0.000° 18.04A 150.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
. . .
ITest = 5.00 In State: Tested Result: Passed
Phase Primary Secondary Tertiary
Itest Angle Imeas Angle Itest Angle Imeas Angle Itest Angle Imeas Angle
A 13.46A -180.0° 0.000A 0.000° 22.55A 30.0° 0.000A 0.000° n/a n/a n/a n/a
B 13.46A 60.0° 0.000A 0.000° 22.55A -90.0° 0.000A 0.000° n/a n/a n/a n/a
C 13.46A -60.0° 0.000A 0.000° 22.55A 150.0° 0.000A 0.000° n/a n/a n/a n/a
N 0.00A 0.0° 0.000A 0.000° 0.00A 0.0° 0.000A 0.000° n/a n/a n/a n/a
Phase Imeas_diff Imeas_bias
A 0.000 In 0.000 In
B 0.000 In 0.000 In
C 0.000 In 0.000 In
.
.
Test State:
Test passed
5 out of 5 points tested.
5 points passed. 0
points failed.
17. Diff Characteristic Slope 1 A-B:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:22:13 Test End: 11-May-2023 11:24:01
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
18. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-L2 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.890 In 1.73 % 0.0151 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
19. Diff Characteristic Slope 1 B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:24:12 Test End: 11-May-2023 11:26:02
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
20. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L2-L3 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.884 In 1.04 % 0.0091 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
21. Diff Characteristic Slope 1 C-A:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:26:17 Test End: 11-May-2023 11:28:08
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
22. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L3-L1 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.890 In 1.73 % 0.0151 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
23. Diff Characteristic Slope 1 A-B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 10:02:14 Test End: 11-May-2023 10:04:24
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.87 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
24. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-L2-L3 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.890 In 1.73 % 0.0151 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
25. Diff Characteristic Slope 1 A-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 10:19:55 Test End: 11-May-2023 10:21:46
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
26. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.890 In 1.73 % 0.0151 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
27. Diff Characteristic Slope 1 B-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:28:49 Test End: 11-May-2023 11:30:40
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
28. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L2-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.884 In 1.04 % 0.0091 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
29. Diff Characteristic Slope 1 C-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:30:55 Test End: 11-May-2023 11:32:45
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 1.50 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 0.68 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
30. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L3-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.300 In 0.297 In -0.83 % -0.0025 In Tested Passed
1.50 In 0.375 In 0.389 In 3.70 % 0.0139 In Tested Passed
2.50 In 0.625 In 0.638 In 2.12 % 0.0132 In Tested Passed
3.50 In 0.875 In 0.890 In 1.73 % 0.0151 In Tested Passed
4.50 In 1.125 In 1.137 In 1.02 % 0.0115 In Tested Passed
5.50 In 1.375 In 1.389 In 1.02 % 0.0140 In Tested Passed
6.50 In 1.625 In 1.639 In 0.84 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
5 10 15 20 25 30 35
Idiff [In]
0
1
2
3
4
5
6
7
8
9
31. Diff Characteristic Slope 2 A-B:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:33:05 Test End: 11-May-2023 11:34:20
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.02 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
32. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-L2 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.774 In 3.14 % 0.0235 In Tested Passed
2.50 In 1.250 In 1.271 In 1.70 % 0.0212 In Tested Passed
3.50 In 1.750 In 1.771 In 1.18 % 0.0206 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.773 In 0.83 % 0.0229 In Tested Passed
6.50 In 3.250 In 3.269 In 0.58 % 0.0189 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
33. Diff Characteristic Slope 2 B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:34:42 Test End: 11-May-2023 11:35:57
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.02 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
34. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L2-L3 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.768 In 2.44 % 0.0183 In Tested Passed
2.50 In 1.250 In 1.271 In 1.70 % 0.0212 In Tested Passed
3.50 In 1.750 In 1.771 In 1.18 % 0.0206 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.773 In 0.83 % 0.0229 In Tested Passed
6.50 In 3.250 In 3.269 In 0.58 % 0.0189 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
35. Diff Characteristic Slope 2 C-A:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:36:19 Test End: 11-May-2023 11:37:34
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.02 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
36. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L3-L1 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.774 In 3.14 % 0.0235 In Tested Passed
2.50 In 1.250 In 1.271 In 1.70 % 0.0212 In Tested Passed
3.50 In 1.750 In 1.771 In 1.18 % 0.0206 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.773 In 0.83 % 0.0229 In Tested Passed
6.50 In 3.250 In 3.269 In 0.58 % 0.0189 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
37. Diff Characteristic Slope 2 A-B-C:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:37:49 Test End: 11-May-2023 11:39:04
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.02 In Prefault time: 0.025 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
38. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-L2-L3 at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.758 In 1.05 % 0.0078 In Tested Passed
2.50 In 1.250 In 1.263 In 1.02 % 0.0127 In Tested Passed
3.50 In 1.750 In 1.759 In 0.50 % 0.0088 In Tested Passed
4.50 In 2.250 In 2.261 In 0.50 % 0.0113 In Tested Passed
5.50 In 2.750 In 2.764 In 0.50 % 0.0137 In Tested Passed
6.50 In 3.250 In 3.263 In 0.41 % 0.0135 In Tested Passed
.
.
Test State:
Test passed
7 out of 7 points tested.
7 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
39. Diff Characteristic Slope 2 A-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:39:24 Test End: 11-May-2023 11:40:32
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.85 In Prefault time: 0.125 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
40. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L1-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.426 In 6.61 % 0.0265 In Tested Passed
1.50 In 0.750 In 0.774 In 3.14 % 0.0235 In Tested Passed
2.50 In 1.250 In 1.280 In 2.38 % 0.0297 In Tested Passed
3.50 In 1.750 In 1.776 In 1.51 % 0.0265 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.773 In 0.83 % 0.0229 In Tested Passed
.
.
Test State:
Test passed
6 out of 6 points tested.
6 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
41. Diff Characteristic Slope 2 B-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:40:54 Test End: 11-May-2023 11:42:02
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.85 In Prefault time: 0.125 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
42. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L2-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.774 In 3.14 % 0.0235 In Tested Passed
2.50 In 1.250 In 1.271 In 1.70 % 0.0212 In Tested Passed
3.50 In 1.750 In 1.771 In 1.18 % 0.0206 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.764 In 0.50 % 0.0137 In Tested Passed
.
.
Test State:
Test passed
6 out of 6 points tested.
6 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
43. Diff Characteristic Slope 2 C-N:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
. .
Test Module
Name: OMICRON Diff Operating
Characteristic
Version: 4.31
Test Start: 11-May-2023 11:42:19 Test End: 11-May-2023 11:43:27
User Name: Manager:
Company:
.
Test Settings
.
General Settings:
Testing: Winding S / Winding W
Max. Test Time: 0.06 s Delay Time: 0.08 s
Prefault: Yes
Prefault current: 1.85 In Prefault time: 0.125 s
Vout enabled: No Vout winding: Winding S
Time-triggered: No Winding/leg output: Winding S
.
Search Test Settings:
Ignore Default Char.: No
44. Resolution Relative: 0.10 % Resolution Absolute: 0.010 In
. . . .
Binary Outputs
Test Results for Fault Location L3-E at Reference Side Winding S
Ibias Idiff
Nominal
Idiff Actual Dev (rel) Dev (abs) Check Test State Result
0.80 In 0.400 In 0.421 In 5.14 % 0.0206 In Tested Passed
1.50 In 0.750 In 0.774 In 3.14 % 0.0235 In Tested Passed
2.50 In 1.250 In 1.271 In 1.70 % 0.0212 In Tested Passed
3.50 In 1.750 In 1.771 In 1.18 % 0.0206 In Tested Passed
4.50 In 2.250 In 2.269 In 0.84 % 0.0188 In Tested Passed
5.50 In 2.750 In 2.773 In 0.83 % 0.0229 In Tested Passed
.
.
Test State:
Test passed
6 out of 6 points tested.
6 points passed. 0
points failed.
Operating Characteristic Diagram
Ibias [In]
2 4 6 8 10 12 14 16 18
Idiff [In]
0
1
2
3
4
5
6
7
8
9
45. Diff 2nd Harmonic Blocking:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
Harmonic Settings:
HR tol abs: 1.00 % HR tol rel: 5.00 %
Harmonic
Order
Start point End point
Ixf/Idiff Idiff/In Ixf/Idiff Idiff/In
2 15.00 % 0.30 15.00 % 8.00
4 inf % 0.50 inf % 8.00
5 35.00 % 0.30 35.00 % 8.00
. .
Test Module
Name: OMICRON Diff Harmonic Restraint Version: 4.31
Test Start: 11-May-2023 10:25:45 Test End: 11-May-2023 10:26:56
User Name: Manager:
Company:
.
Test Settings
Testing: Winding S Tested Harmonic: 2
Max. Test Time: 1.50 s Delay Time: 0.08 s
Postfault active: No Postfault Time: 0.04 s
Ignore Default Char.: No Search resolution: 0.010
46. Vout enabled: No Vout winding: Winding S
. . . .
Binary Outputs
Test Results for Testphase L1-L2-L3 at Reference Side Winding S for 2. Harmonic
Idiff Ixf/Idiff
Nominal
Ixf/Idiff
Actual
Angle
(Ixf,Idiff)
Dev (rel) Dev.(abs) Check Test State Result
1.00 I/In 15.000 % 15.04 % -120.0 ° 0.23 % 0.0351 Tested Passed
2.00 I/In 15.000 % 15.02 % -120.0 ° 0.13 % 0.0195 Tested Passed
3.00 I/In 15.000 % 15.01 % -120.0 ° 0.08 % 0.0117 Tested Passed
.
State:
3 out of 3 points tested. 3 points
passed. 0 points failed.
General Assessment: Test
passed
Harmonic Restraint Test Plane
I2f/Idiff [%]
2 4 6 8 10 12 14 16
Idiff/In [In]
0
1
2
3
4
5
6
7
8
9
47. Diff 5th Harmonic Blocking:
Test Object - Differential Parameters
Protected Object:
Protected Object: Transformer
Vector Group: YD11
Winding/Leg Name: Winding S Winding W
Voltage: 33.50 kV 10.00 kV
Power: 25.00 MVA 25.00 MVA
Starpoint Grounding: Yes No
Delta-connected CT: No No
CT:
Winding/Leg Name: Winding S Winding W
CT Current Prim: 800.00 A 1600.00 A
CT Current Sec: 5.00 A 5.00 A
CT Grounding: tow. Prot. Obj. tow. Prot. Obj.
Gnd CT Prim Current: 200.00 A 800.00 A
Gnd CT Sec Current: 1.00 A 1.00 A
Gnd CT Grounding: n/a n/a
.
Protection device:
Reference Winding: Winding S
Ibias Calculation: ( |Ip| + |Is| ) / K1 (K1 = 1.00)
Zero Seq. Elimination: IL-I0
Reference Current: PO nominal current
Ground CT Used: No
Disable Comb. char.: Yes
Idiff>: 0.30 In tdiff>: 0.01 s
Idiff>>: 8.00 In tdiff>>: 0.01 s
Itol rel: 5.00 % ttol rel: 1.00 %
Itol abs: 0.02 In ttol abs: 0.07 s
Harmonic Settings:
HR tol abs: 1.00 % HR tol rel: 5.00 %
Harmonic
Order
Start point End point
Ixf/Idiff Idiff/In Ixf/Idiff Idiff/In
2 15.00 % 0.30 15.00 % 8.00
4 inf % 0.50 inf % 8.00
5 35.00 % 0.30 35.00 % 8.00
. .
Test Module
Name: OMICRON Diff Harmonic Restraint Version: 4.31
Test Start: 11-May-2023 10:28:22 Test End: 11-May-2023 10:29:42
User Name: Manager:
Company:
.
Test Settings
Testing: Winding S Tested Harmonic: 5
Max. Test Time: 1.50 s Delay Time: 0.08 s
Postfault active: No Postfault Time: 0.04 s
Ignore Default Char.: Yes Search resolution: 0.010
48. Vout enabled: No Vout winding: Winding S
. . . .
Binary Outputs
Test Results for Testphase L1-L2-L3 at Reference Side Winding S for 5. Harmonic
Idiff Ixf/Idiff
Nominal
Ixf/Idiff
Actual
Angle
(Ixf,Idiff)
Dev (rel) Dev.(abs) Check Test State Result
1.00 I/In n/a 36.27 % -120.0 ° n/a n/a Tested Passed
2.00 I/In n/a 36.23 % -120.0 ° n/a n/a Tested Passed
3.00 I/In n/a 36.12 % -120.0 ° n/a n/a Tested Passed
.
State:
3 out of 3 points tested. 3 points
passed. 0 points failed.
General Assessment: Test
passed
Harmonic Restraint Test Plane
I5f/Idiff [%]
5 10 15 20 25 30 35 40
Idiff/In [In]
0
1
2
3
4
5
6
7
8
9
49. Winding S Overcurrent A-B lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:10:52 Test End: 11-May-2023 11:11:17
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 100.0 mA
Load angle: -10.00 °
50. Prefault time: 200.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L1-L2 (---) n/a 5.000 A n/a 3.325 s 2.865 s 3.894 s
L1-L2 (---) n/a 7.000 A n/a 1.705 s 1.546 s 1.875 s
L1-L2 (---) n/a 9.000 A n/a 1.248 s 1.143 s 1.357 s
L1-L2 (---) n/a 11.00 A n/a 1.027 s 942.4 ms 1.114 s
L1-L2 (---) n/a 13.00 A n/a 895.0 ms 820.6 ms 970.4 ms
L1-L2 (---) n/a 15.00 A n/a 805.9 ms 737.7 ms 874.6 ms
L1-L2 (---) n/a 17.00 A n/a 741.1 ms 677.1 ms 805.4 ms
L1-L2 (---) n/a 19.00 A n/a 691.6 ms 630.6 ms 752.8 ms
L1-L2 (---) n/a 21.00 A n/a 652.3 ms 59.67 ms 711.2 ms
L1-L2 (---) n/a 23.00 A n/a 100.0 ms 59.67 ms 677.4 ms
L1-L2 (---) n/a 25.00 A n/a 100.0 ms 59.67 ms 140.3 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L1-L2 (---) n/a 5.000 A n/a 3.325 s 3.345 s 0.6050 % No Passed
L1-L2 (---) n/a 7.000 A n/a 1.705 s 1.720 s 0.8895 % No Passed
L1-L2 (---) n/a 9.000 A n/a 1.248 s 1.263 s 1.217 % No Passed
L1-L2 (---) n/a 11.00 A n/a 1.027 s 1.043 s 1.496 % No Passed
L1-L2 (---) n/a 13.00 A n/a 895.0 ms 903.9 ms 0.9904 % No Passed
L1-L2 (---) n/a 15.00 A n/a 805.9 ms 816.4 ms 1.307 % No Passed
L1-L2 (---) n/a 17.00 A n/a 741.1 ms 750.4 ms 1.253 % No Passed
L1-L2 (---) n/a 19.00 A n/a 691.6 ms 698.1 ms 0.9382 % No Passed
L1-L2 (---) n/a 21.00 A n/a 652.3 ms 660.5 ms 1.254 % No Passed
L1-L2 (---) n/a 23.00 A n/a 100.0 ms 126.7 ms 26.70 % No Passed
L1-L2 (---) n/a 25.00 A n/a 100.0 ms 125.9 ms 25.90 % No Passed
.
Charts for Fault Types:
Type Angle
L1-L2 n/a
51. .
Test State:
11 out of 11 points tested.
11 points passed.
0 points failed.
Test passed
Winding S Overcurrent B-C lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
I/A
5 7 10 20 30 50 70
t/s
0.10
1.00
10.00
100.00
1000.00
10000.00
52. Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:12:52 Test End: 11-May-2023 11:13:15
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L2-L3 (---) n/a 5.000 A n/a 3.325 s 2.865 s 3.894 s
L2-L3 (---) n/a 7.000 A n/a 1.705 s 1.546 s 1.875 s
L2-L3 (---) n/a 9.000 A n/a 1.248 s 1.143 s 1.357 s
L2-L3 (---) n/a 11.00 A n/a 1.027 s 942.4 ms 1.114 s
L2-L3 (---) n/a 13.00 A n/a 895.0 ms 820.6 ms 970.4 ms
L2-L3 (---) n/a 15.00 A n/a 805.9 ms 737.7 ms 874.6 ms
L2-L3 (---) n/a 17.00 A n/a 741.1 ms 677.1 ms 805.4 ms
L2-L3 (---) n/a 19.00 A n/a 691.6 ms 630.6 ms 752.8 ms
L2-L3 (---) n/a 21.00 A n/a 652.3 ms 59.67 ms 711.2 ms
L2-L3 (---) n/a 23.00 A n/a 100.0 ms 59.67 ms 677.4 ms
L2-L3 (---) n/a 25.00 A n/a 100.0 ms 59.67 ms 140.3 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
53. Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L2-L3 (---) n/a 5.000 A n/a 3.325 s 3.344 s 0.5810 % No Passed
L2-L3 (---) n/a 7.000 A n/a 1.705 s 1.718 s 0.7898 % No Passed
L2-L3 (---) n/a 9.000 A n/a 1.248 s 1.263 s 1.217 % No Passed
L2-L3 (---) n/a 11.00 A n/a 1.027 s 1.039 s 1.097 % No Passed
L2-L3 (---) n/a 13.00 A n/a 895.0 ms 901.3 ms 0.6999 % No Passed
L2-L3 (---) n/a 15.00 A n/a 805.9 ms 813.6 ms 0.9597 % No Passed
L2-L3 (---) n/a 17.00 A n/a 741.1 ms 747.4 ms 0.8484 % No Passed
L2-L3 (---) n/a 19.00 A n/a 691.6 ms 697.8 ms 0.8948 % No Passed
L2-L3 (---) n/a 21.00 A n/a 652.3 ms 658.4 ms 0.9316 % No Passed
L2-L3 (---) n/a 23.00 A n/a 100.0 ms 125.8 ms 25.80 % No Passed
L2-L3 (---) n/a 25.00 A n/a 100.0 ms 126.0 ms 26.00 % No Passed
.
Charts for Fault Types:
Type Angle
L2-L3 n/a
.
Test State:
11 out of 11 points tested.
11 points passed.
0 points failed.
Test passed
I/A
5 7 10 20 30 50 70
t/s
0.10
1.00
10.00
100.00
1000.00
10000.00
54. Winding S Overcurrent C-A lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:13:31 Test End: 11-May-2023 11:13:54
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
55. Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L3-L1 (---) n/a 5.000 A n/a 3.325 s 2.865 s 3.894 s
L3-L1 (---) n/a 7.000 A n/a 1.705 s 1.546 s 1.875 s
L3-L1 (---) n/a 9.000 A n/a 1.248 s 1.143 s 1.357 s
L3-L1 (---) n/a 11.00 A n/a 1.027 s 942.4 ms 1.114 s
L3-L1 (---) n/a 13.00 A n/a 895.0 ms 820.6 ms 970.4 ms
L3-L1 (---) n/a 15.00 A n/a 805.9 ms 737.7 ms 874.6 ms
L3-L1 (---) n/a 17.00 A n/a 741.1 ms 677.1 ms 805.4 ms
L3-L1 (---) n/a 19.00 A n/a 691.6 ms 630.6 ms 752.8 ms
L3-L1 (---) n/a 21.00 A n/a 652.3 ms 59.67 ms 711.2 ms
L3-L1 (---) n/a 23.00 A n/a 100.0 ms 59.67 ms 677.4 ms
L3-L1 (---) n/a 25.00 A n/a 100.0 ms 59.67 ms 140.3 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L3-L1 (---) n/a 5.000 A n/a 3.325 s 3.344 s 0.5810 % No Passed
L3-L1 (---) n/a 7.000 A n/a 1.705 s 1.720 s 0.9071 % No Passed
L3-L1 (---) n/a 9.000 A n/a 1.248 s 1.261 s 1.008 % No Passed
L3-L1 (---) n/a 11.00 A n/a 1.027 s 1.040 s 1.234 % No Passed
L3-L1 (---) n/a 13.00 A n/a 895.0 ms 907.7 ms 1.415 % No Passed
L3-L1 (---) n/a 15.00 A n/a 805.9 ms 815.6 ms 1.208 % No Passed
L3-L1 (---) n/a 17.00 A n/a 741.1 ms 746.6 ms 0.7404 % No Passed
L3-L1 (---) n/a 19.00 A n/a 691.6 ms 697.6 ms 0.8659 % No Passed
L3-L1 (---) n/a 21.00 A n/a 652.3 ms 660.5 ms 1.254 % No Passed
L3-L1 (---) n/a 23.00 A n/a 100.0 ms 124.2 ms 24.20 % No Passed
L3-L1 (---) n/a 25.00 A n/a 100.0 ms 125.0 ms 25.00 % No Passed
.
Charts for Fault Types:
Type Angle
L3-L1 n/a
56. .
Test State:
11 out of 11 points tested.
11 points passed.
0 points failed.
Test passed
Winding S Overcurrent A-B-C lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
I/A
5 7 10 20 30 50 70
t/s
0.10
1.00
10.00
100.00
1000.00
10000.00
57. Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 10:39:10 Test End: 11-May-2023 10:39:33
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L1-L2-L3 (---) n/a 5.000 A n/a 3.325 s 2.865 s 3.894 s
L1-L2-L3 (---) n/a 7.000 A n/a 1.705 s 1.546 s 1.875 s
L1-L2-L3 (---) n/a 9.000 A n/a 1.248 s 1.143 s 1.357 s
L1-L2-L3 (---) n/a 11.00 A n/a 1.027 s 942.4 ms 1.114 s
L1-L2-L3 (---) n/a 13.00 A n/a 895.0 ms 820.6 ms 970.4 ms
L1-L2-L3 (---) n/a 15.00 A n/a 805.9 ms 737.7 ms 874.6 ms
L1-L2-L3 (---) n/a 17.00 A n/a 741.1 ms 677.1 ms 805.4 ms
L1-L2-L3 (---) n/a 19.00 A n/a 691.6 ms 630.6 ms 752.8 ms
L1-L2-L3 (---) n/a 21.00 A n/a 652.3 ms 59.67 ms 711.2 ms
L1-L2-L3 (---) n/a 23.00 A n/a 100.0 ms 59.67 ms 677.4 ms
L1-L2-L3 (---) n/a 25.00 A n/a 100.0 ms 59.67 ms 140.3 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
58. Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L1-L2-L3 (---) n/a 5.000 A n/a 3.325 s 3.343 s 0.5479 % No Passed
L1-L2-L3 (---) n/a 7.000 A n/a 1.705 s 1.718 s 0.7605 % No Passed
L1-L2-L3 (---) n/a 9.000 A n/a 1.248 s 1.259 s 0.8722 % No Passed
L1-L2-L3 (---) n/a 11.00 A n/a 1.027 s 1.038 s 1.078 % No Passed
L1-L2-L3 (---) n/a 13.00 A n/a 895.0 ms 902.6 ms 0.8452 % No Passed
L1-L2-L3 (---) n/a 15.00 A n/a 805.9 ms 811.8 ms 0.7364 % No Passed
L1-L2-L3 (---) n/a 17.00 A n/a 741.1 ms 746.8 ms 0.7674 % No Passed
L1-L2-L3 (---) n/a 19.00 A n/a 691.6 ms 698.1 ms 0.9382 % No Passed
L1-L2-L3 (---) n/a 21.00 A n/a 652.3 ms 657.5 ms 0.7937 % No Passed
L1-L2-L3 (---) n/a 23.00 A n/a 100.0 ms 121.3 ms 21.30 % No Passed
L1-L2-L3 (---) n/a 25.00 A n/a 100.0 ms 121.7 ms 21.70 % No Passed
.
Charts for Fault Types:
Type Angle
L1-L2-L3 n/a
.
Test State:
11 out of 11 points tested.
11 points passed.
0 points failed.
Test passed
I/A
5 7 10 20 30 50 70
t/s
0.10
1.00
10.00
100.00
1000.00
10000.00
59. Winding S Overcurrent A-N lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:15:43 Test End: 11-May-2023 11:15:55
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
60. Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L1-E (---) n/a 300.0 mA n/a 200.0 ms 159.7 ms No trip
L1-E (---) n/a 500.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L1-E (---) n/a 700.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L1-E (---) n/a 900.0 mA n/a 200.0 ms 9.667 ms 240.3 ms
L1-E (---) n/a 1.100 A n/a 50.00 ms 9.667 ms 240.3 ms
L1-E (---) n/a 1.300 A n/a 50.00 ms 9.667 ms 90.33 ms
L1-E (---) n/a 1.500 A n/a 50.00 ms 9.667 ms 90.33 ms
L1-E (---) n/a 1.700 A n/a 50.00 ms 9.667 ms 90.33 ms
L1-E (---) n/a 1.900 A n/a 50.00 ms 9.667 ms 90.33 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L1-E (---) n/a 300.0 mA n/a 200.0 ms 223.4 ms 11.70 % No Passed
L1-E (---) n/a 500.0 mA n/a 200.0 ms 218.0 ms 9.000 % No Passed
L1-E (---) n/a 700.0 mA n/a 200.0 ms 216.0 ms 8.000 % No Passed
L1-E (---) n/a 900.0 mA n/a 200.0 ms 209.9 ms 4.950 % No Passed
L1-E (---) n/a 1.100 A n/a 50.00 ms 76.50 ms 53.00 % No Passed
L1-E (---) n/a 1.300 A n/a 50.00 ms 73.40 ms 46.80 % No Passed
L1-E (---) n/a 1.500 A n/a 50.00 ms 66.70 ms 33.40 % No Passed
L1-E (---) n/a 1.700 A n/a 50.00 ms 67.90 ms 35.80 % No Passed
L1-E (---) n/a 1.900 A n/a 50.00 ms 67.60 ms 35.20 % No Passed
.
Charts for Fault Types:
Type Angle
L1-E n/a
61. .
Test State:
9 out of 9 points tested.
9 points passed.
0 points failed.
Test passed
Winding S Overcurrent B-N lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
I/A
0.2 0.5 1.0 2.0 5.0 10.0 20.0 50.0
t/s
0.010
0.100
1.000
10.000
100.000
1000.000
10000.000
62. Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:16:08 Test End: 11-May-2023 11:16:19
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L2-E (---) n/a 300.0 mA n/a 200.0 ms 159.7 ms No trip
L2-E (---) n/a 500.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L2-E (---) n/a 700.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L2-E (---) n/a 900.0 mA n/a 200.0 ms 9.667 ms 240.3 ms
L2-E (---) n/a 1.100 A n/a 50.00 ms 9.667 ms 240.3 ms
L2-E (---) n/a 1.300 A n/a 50.00 ms 9.667 ms 90.33 ms
L2-E (---) n/a 1.500 A n/a 50.00 ms 9.667 ms 90.33 ms
L2-E (---) n/a 1.700 A n/a 50.00 ms 9.667 ms 90.33 ms
L2-E (---) n/a 1.900 A n/a 50.00 ms 9.667 ms 90.33 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
63. Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L2-E (---) n/a 300.0 mA n/a 200.0 ms 223.1 ms 11.55 % No Passed
L2-E (---) n/a 500.0 mA n/a 200.0 ms 215.6 ms 7.800 % No Passed
L2-E (---) n/a 700.0 mA n/a 200.0 ms 215.6 ms 7.800 % No Passed
L2-E (---) n/a 900.0 mA n/a 200.0 ms 210.0 ms 5.000 % No Passed
L2-E (---) n/a 1.100 A n/a 50.00 ms 76.50 ms 53.00 % No Passed
L2-E (---) n/a 1.300 A n/a 50.00 ms 68.00 ms 36.00 % No Passed
L2-E (---) n/a 1.500 A n/a 50.00 ms 67.60 ms 35.20 % No Passed
L2-E (---) n/a 1.700 A n/a 50.00 ms 66.90 ms 33.80 % No Passed
L2-E (---) n/a 1.900 A n/a 50.00 ms 65.50 ms 31.00 % No Passed
.
Charts for Fault Types:
Type Angle
L2-E n/a
.
Test State:
9 out of 9 points tested.
9 points passed.
0 points failed.
Test passed
I/A
0.2 0.5 1.0 2.0 5.0 10.0 20.0 50.0
t/s
0.010
0.100
1.000
10.000
100.000
1000.000
10000.000
64. Winding S Overcurrent C-N lado 33kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50SP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Yes 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
No 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50SG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
Yes 50SG2 IEC Definite Time 0.20 Iref 0.05 s 0.95 Non Directional
No 50SG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50SQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50SQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 11:16:33 Test End: 11-May-2023 11:16:44
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
65. Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L3-E (---) n/a 300.0 mA n/a 200.0 ms 159.7 ms No trip
L3-E (---) n/a 500.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L3-E (---) n/a 700.0 mA n/a 200.0 ms 159.7 ms 240.3 ms
L3-E (---) n/a 900.0 mA n/a 200.0 ms 9.667 ms 240.3 ms
L3-E (---) n/a 1.100 A n/a 50.00 ms 9.667 ms 240.3 ms
L3-E (---) n/a 1.300 A n/a 50.00 ms 9.667 ms 90.33 ms
L3-E (---) n/a 1.500 A n/a 50.00 ms 9.667 ms 90.33 ms
L3-E (---) n/a 1.700 A n/a 50.00 ms 9.667 ms 90.33 ms
L3-E (---) n/a 1.900 A n/a 50.00 ms 9.667 ms 90.33 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 33kV 1
Trip 2 Lado 33kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L3-E (---) n/a 300.0 mA n/a 200.0 ms 222.0 ms 11.00 % No Passed
L3-E (---) n/a 500.0 mA n/a 200.0 ms 218.2 ms 9.100 % No Passed
L3-E (---) n/a 700.0 mA n/a 200.0 ms 213.9 ms 6.950 % No Passed
L3-E (---) n/a 900.0 mA n/a 200.0 ms 215.9 ms 7.950 % No Passed
L3-E (---) n/a 1.100 A n/a 50.00 ms 73.40 ms 46.80 % No Passed
L3-E (---) n/a 1.300 A n/a 50.00 ms 72.70 ms 45.40 % No Passed
L3-E (---) n/a 1.500 A n/a 50.00 ms 68.10 ms 36.20 % No Passed
L3-E (---) n/a 1.700 A n/a 50.00 ms 65.90 ms 31.80 % No Passed
L3-E (---) n/a 1.900 A n/a 50.00 ms 68.30 ms 36.60 % No Passed
.
Charts for Fault Types:
Type Angle
L3-E n/a
66. .
Test State:
9 out of 9 points tested.
9 points passed.
0 points failed.
Test passed
I/A
0.2 0.5 1.0 2.0 5.0 10.0 20.0 50.0
t/s
0.010
0.100
1.000
10.000
100.000
1000.000
10000.000
67. Winding W Overcurrent A-B lado 10kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50WP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
Yes 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50WG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
No 50WG2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 10:45:56 Test End: 11-May-2023 10:46:29
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
68. Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L1-L2 (---) n/a 7.000 A n/a 4.324 s 3.314 s 6.022 s
L1-L2 (---) n/a 8.000 A n/a 2.466 s 2.076 s 2.966 s
L1-L2 (---) n/a 9.000 A n/a 1.787 s 1.555 s 2.057 s
L1-L2 (---) n/a 10.00 A n/a 1.433 s 1.267 s 1.618 s
L1-L2 (---) n/a 11.00 A n/a 1.215 s 1.083 s 1.358 s
L1-L2 (---) n/a 12.00 A n/a 1.067 s 954.5 ms 1.185 s
L1-L2 (---) n/a 13.00 A n/a 958.7 ms 859.9 ms 1.062 s
L1-L2 (---) n/a 14.00 A n/a 876.5 ms 786.9 ms 969.3 ms
L1-L2 (---) n/a 15.00 A n/a 811.6 ms 728.8 ms 896.7 ms
L1-L2 (---) n/a 16.00 A n/a 758.9 ms 681.3 ms 838.4 ms
L1-L2 (---) n/a 17.00 A n/a 715.3 ms 641.7 ms 790.3 ms
L1-L2 (---) n/a 18.00 A n/a 678.5 ms 608.1 ms 750.0 ms
L1-L2 (---) n/a 19.00 A n/a 646.9 ms 579.2 ms 715.6 ms
L1-L2 (---) n/a 20.00 A n/a 619.6 ms 554.1 ms 685.9 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 10kV 1
Trip 2 Lado 10kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L1-L2 (---) n/a 7.000 A n/a 4.324 s 4.350 s 0.5950 % No Passed
L1-L2 (---) n/a 8.000 A n/a 2.466 s 2.484 s 0.7231 % No Passed
L1-L2 (---) n/a 9.000 A n/a 1.787 s 1.806 s 1.043 % No Passed
L1-L2 (---) n/a 10.00 A n/a 1.433 s 1.448 s 1.013 % No Passed
L1-L2 (---) n/a 11.00 A n/a 1.215 s 1.231 s 1.314 % No Passed
L1-L2 (---) n/a 12.00 A n/a 1.067 s 1.081 s 1.341 % No Passed
L1-L2 (---) n/a 13.00 A n/a 958.7 ms 975.5 ms 1.754 % No Passed
L1-L2 (---) n/a 14.00 A n/a 876.5 ms 891.2 ms 1.682 % No Passed
L1-L2 (---) n/a 15.00 A n/a 811.6 ms 825.4 ms 1.705 % No Passed
L1-L2 (---) n/a 16.00 A n/a 758.9 ms 772.8 ms 1.829 % No Passed
L1-L2 (---) n/a 17.00 A n/a 715.3 ms 726.6 ms 1.581 % No Passed
L1-L2 (---) n/a 18.00 A n/a 678.5 ms 688.8 ms 1.523 % No Passed
L1-L2 (---) n/a 19.00 A n/a 646.9 ms 659.5 ms 1.943 % No Passed
L1-L2 (---) n/a 20.00 A n/a 619.6 ms 630.7 ms 1.795 % No Passed
.
69. Charts for Fault Types:
Type Angle
L1-L2 n/a
Test State:
14 out of 14 points tested.
14 points passed.
0 points failed.
Test passed
Winding W Overcurrent B-C lado 10kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50WP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
Yes 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50WG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
No 50WG2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
I/A
7 10 20 30 50 70 100
t/s
1.0
10.0
100.0
1000.0
10000.0
70. .
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 10:46:44 Test End: 11-May-2023 10:47:17
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L2-L3 (---) n/a 7.000 A n/a 4.324 s 3.314 s 6.022 s
L2-L3 (---) n/a 8.000 A n/a 2.466 s 2.076 s 2.966 s
L2-L3 (---) n/a 9.000 A n/a 1.787 s 1.555 s 2.057 s
L2-L3 (---) n/a 10.00 A n/a 1.433 s 1.267 s 1.618 s
L2-L3 (---) n/a 11.00 A n/a 1.215 s 1.083 s 1.358 s
L2-L3 (---) n/a 12.00 A n/a 1.067 s 954.5 ms 1.185 s
L2-L3 (---) n/a 13.00 A n/a 958.7 ms 859.9 ms 1.062 s
L2-L3 (---) n/a 14.00 A n/a 876.5 ms 786.9 ms 969.3 ms
L2-L3 (---) n/a 15.00 A n/a 811.6 ms 728.8 ms 896.7 ms
L2-L3 (---) n/a 16.00 A n/a 758.9 ms 681.3 ms 838.4 ms
L2-L3 (---) n/a 17.00 A n/a 715.3 ms 641.7 ms 790.3 ms
L2-L3 (---) n/a 18.00 A n/a 678.5 ms 608.1 ms 750.0 ms
L2-L3 (---) n/a 19.00 A n/a 646.9 ms 579.2 ms 715.6 ms
L2-L3 (---) n/a 20.00 A n/a 619.6 ms 554.1 ms 685.9 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
71. Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 10kV 1
Trip 2 Lado 10kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L2-L3 (---) n/a 7.000 A n/a 4.324 s 4.345 s 0.4909 % No Passed
L2-L3 (---) n/a 8.000 A n/a 2.466 s 2.484 s 0.7352 % No Passed
L2-L3 (---) n/a 9.000 A n/a 1.787 s 1.801 s 0.7908 % No Passed
L2-L3 (---) n/a 10.00 A n/a 1.433 s 1.445 s 0.7964 % No Passed
L2-L3 (---) n/a 11.00 A n/a 1.215 s 1.229 s 1.166 % No Passed
L2-L3 (---) n/a 12.00 A n/a 1.067 s 1.078 s 1.069 % No Passed
L2-L3 (---) n/a 13.00 A n/a 958.7 ms 975.9 ms 1.796 % No Passed
L2-L3 (---) n/a 14.00 A n/a 876.5 ms 892.9 ms 1.876 % No Passed
L2-L3 (---) n/a 15.00 A n/a 811.6 ms 823.1 ms 1.422 % No Passed
L2-L3 (---) n/a 16.00 A n/a 758.9 ms 773.8 ms 1.960 % No Passed
L2-L3 (---) n/a 17.00 A n/a 715.3 ms 728.9 ms 1.903 % No Passed
L2-L3 (---) n/a 18.00 A n/a 678.5 ms 691.8 ms 1.965 % No Passed
L2-L3 (---) n/a 19.00 A n/a 646.9 ms 661.9 ms 2.314 % No Passed
L2-L3 (---) n/a 20.00 A n/a 619.6 ms 629.8 ms 1.649 % No Passed
.
Charts for Fault Types:
Type Angle
L2-L3 n/a
.
Test State:
14 out of 14 points tested.
14 points passed.
0 points failed.
Test passed
I/A
7 10 20 30 50 70 100
t/s
1.0
10.0
100.0
1000.0
10000.0
72. Winding W Overcurrent C-A lado 10kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50WP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
Yes 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50WG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
No 50WG2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
.
Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
. .
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 10:47:32 Test End: 11-May-2023 10:48:05
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
73. Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L3-L1 (---) n/a 7.000 A n/a 4.324 s 3.314 s 6.022 s
L3-L1 (---) n/a 8.000 A n/a 2.466 s 2.076 s 2.966 s
L3-L1 (---) n/a 9.000 A n/a 1.787 s 1.555 s 2.057 s
L3-L1 (---) n/a 10.00 A n/a 1.433 s 1.267 s 1.618 s
L3-L1 (---) n/a 11.00 A n/a 1.215 s 1.083 s 1.358 s
L3-L1 (---) n/a 12.00 A n/a 1.067 s 954.5 ms 1.185 s
L3-L1 (---) n/a 13.00 A n/a 958.7 ms 859.9 ms 1.062 s
L3-L1 (---) n/a 14.00 A n/a 876.5 ms 786.9 ms 969.3 ms
L3-L1 (---) n/a 15.00 A n/a 811.6 ms 728.8 ms 896.7 ms
L3-L1 (---) n/a 16.00 A n/a 758.9 ms 681.3 ms 838.4 ms
L3-L1 (---) n/a 17.00 A n/a 715.3 ms 641.7 ms 790.3 ms
L3-L1 (---) n/a 18.00 A n/a 678.5 ms 608.1 ms 750.0 ms
L3-L1 (---) n/a 19.00 A n/a 646.9 ms 579.2 ms 715.6 ms
L3-L1 (---) n/a 20.00 A n/a 619.6 ms 554.1 ms 685.9 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0
Binary Inputs:
Trigger Logic: Or
Name Trigger State
Trip 1 Lado 10kV 1
Trip 2 Lado 10kV 1
.
Shot Test Results:
Type Relative To Factor Magnitude Angle tnom tact Deviation Overload Result
L3-L1 (---) n/a 7.000 A n/a 4.324 s 4.346 s 0.5117 % No Passed
L3-L1 (---) n/a 8.000 A n/a 2.466 s 2.483 s 0.7028 % No Passed
L3-L1 (---) n/a 9.000 A n/a 1.787 s 1.802 s 0.8468 % No Passed
L3-L1 (---) n/a 10.00 A n/a 1.433 s 1.447 s 0.9639 % No Passed
L3-L1 (---) n/a 11.00 A n/a 1.215 s 1.228 s 1.076 % No Passed
L3-L1 (---) n/a 12.00 A n/a 1.067 s 1.080 s 1.294 % No Passed
L3-L1 (---) n/a 13.00 A n/a 958.7 ms 974.1 ms 1.608 % No Passed
L3-L1 (---) n/a 14.00 A n/a 876.5 ms 891.4 ms 1.705 % No Passed
L3-L1 (---) n/a 15.00 A n/a 811.6 ms 824.8 ms 1.632 % No Passed
L3-L1 (---) n/a 16.00 A n/a 758.9 ms 775.0 ms 2.118 % No Passed
L3-L1 (---) n/a 17.00 A n/a 715.3 ms 729.2 ms 1.945 % No Passed
L3-L1 (---) n/a 18.00 A n/a 678.5 ms 690.3 ms 1.744 % No Passed
L3-L1 (---) n/a 19.00 A n/a 646.9 ms 659.0 ms 1.866 % No Passed
L3-L1 (---) n/a 20.00 A n/a 619.6 ms 632.5 ms 2.085 % No Passed
.
74. Charts for Fault Types:
Type Angle
L3-L1 n/a
.
Test State:
14 out of 14 points tested.
14 points passed.
0 points failed.
Test passed
Winding W Overcurrent A-B-C lado 10kV:
Test Object - Overcurrent Parameters
.
General - Values:
TimeTolAbs: 0.04 s VT connection: n/a
TimeTolRel: 1.00 % CT starpoint connection: n/a
CurrentTolAbs: 0.02 Iref
CurrentTolRel: 5.00 %
Directional: No
.
Elements - Phase:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WP1 IEC Definite Time 4.40 Iref 0.10 s 0.95 Non Directional
No 50WP2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WP3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 51O01 C1 Standard Inverse 0.70 Iref 0.17 0.95 Non Directional
Yes 51O02 C1 Standard Inverse 1.17 Iref 0.11 0.95 Non Directional
No 51O03 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O04 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O05 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O06 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O07 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O08 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O09 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
No 51O10 U1 Moderately Inverse 0.20 Iref 1.00 0.95 Non Directional
.
Elements - Residual:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
Yes 50WG1 IEC Definite Time 0.05 Iref 0.20 s 0.95 Non Directional
No 50WG2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WG3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
I/A
7 10 20 30 50 70 100
t/s
1.0
10.0
100.0
1000.0
10000.0
75. Elements - Negative Sequence:
Active Name Tripping characteristic I Pick-up Time Reset Ratio Direction
No 50WQ1 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ2 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
No 50WQ3 IEC Definite Time +∞Iref 0.00 s 0.95 Non Directional
Test Module
Name: OMICRON Overcurrent Version: 4.31
Test Start: 11-May-2023 10:48:42 Test End: 11-May-2023 10:49:15
User Name: Manager:
Company:
Test Settings:
.
Fault Model:
Time reference: Fault inception
Load current: 0.00 A
Load angle: n/a
Prefault time: 100.0 ms
Abs. max time: 240.0 s
Post fault time: 500.0 ms
Rel. max time: 100.0 %
Enable voltage output: No
Fault voltage LN (for all but two phase faults): n/a
Fault voltage LL (for two phase faults): n/a
Decaying DC active: No
Time constant: n/a
CB char min time: 50.00 ms
Thermal reset active: No
Thermal reset method: n/a
Thermal reset message: n/a
.
Shot Test:
Type Relative To Factor Magnitude Angle tnom tmin tmax
L1-L2-L3 (---) n/a 7.000 A n/a 4.324 s 3.314 s 6.022 s
L1-L2-L3 (---) n/a 8.000 A n/a 2.466 s 2.076 s 2.966 s
L1-L2-L3 (---) n/a 9.000 A n/a 1.787 s 1.555 s 2.057 s
L1-L2-L3 (---) n/a 10.00 A n/a 1.433 s 1.267 s 1.618 s
L1-L2-L3 (---) n/a 11.00 A n/a 1.215 s 1.083 s 1.358 s
L1-L2-L3 (---) n/a 12.00 A n/a 1.067 s 954.5 ms 1.185 s
L1-L2-L3 (---) n/a 13.00 A n/a 958.7 ms 859.9 ms 1.062 s
L1-L2-L3 (---) n/a 14.00 A n/a 876.5 ms 786.9 ms 969.3 ms
L1-L2-L3 (---) n/a 15.00 A n/a 811.6 ms 728.8 ms 896.7 ms
L1-L2-L3 (---) n/a 16.00 A n/a 758.9 ms 681.3 ms 838.4 ms
L1-L2-L3 (---) n/a 17.00 A n/a 715.3 ms 641.7 ms 790.3 ms
L1-L2-L3 (---) n/a 18.00 A n/a 678.5 ms 608.1 ms 750.0 ms
L1-L2-L3 (---) n/a 19.00 A n/a 646.9 ms 579.2 ms 715.6 ms
L1-L2-L3 (---) n/a 20.00 A n/a 619.6 ms 554.1 ms 685.9 ms
.
Binary Outputs:
Name State
Bin. Out 1 0
Bin. Out 2 0
Bin. Out 3 0
Bin. Out 4 0