This document discusses aluminum foil jumbo rolls used for hair foil in hair treatments. It describes the differences between DC and CC aluminum foil, including that CC foil has higher strength and faster work hardening during rolling. The manufacturing process for aluminum foil rolls is also outlined, noting the use of different rolling oils - a conventional oil for rough and finish rolling and a low flash point oil for winding to help remove oil residues during annealing.

1. Aluminum Foil Jumbor Roll for Hair Foil
Abstract: Haomei Aluminum offers 1200 and 1235 aluminum foil jumbo roll for
hair foil. How about the differences between DC and CC aluminum foil? And
what is the manufacturing process? Learn more.
Aluminum Foil Jumbo Roll
The hair foil is used to wrap the hair during various perm and dyeing. It has a
heat preservation effect, which can shorten the time of hair treatment and
avoid the pollution of hairdressing chemicals. It also contributes to the the rich
hair styles.
The present aluminum for hairdressing is cut from aluminum jumbo roll with
a smooth surface. Some hair foil producer likes to paint the aluminum foils to
get different colors. Haomei Alumium offers 1200 and 1235 aluminum foil with
different thicknesses. In this month, one of our old British customers just
ordered 10 tons of 1235 aluminum foil in 17 microns.
Our aluminum jumbo roll has the following advantages:
1. It is of small specific gravity and low cost.
2. It has high conductivity.

2. 3. It has good thermal conductivity and strong radiation heat insulation ability.
4. It has good air tightness.
5. It has high strength ratio.
6. It is more corrosion resistant in daily environment.
7. It has good cold deformation performance.
8. It is not magnetized.
The Specification of Aluminum Hair Foil Jumbo Roll
Alloy Temper Thickness Inner
Diameter
Maximum
Outer
Diameter
8011 O 0.01-0.025mm 76 mm 500mm
1200 O 0.01-0.025mm 76 mm 500mm
1235 O 0.01-0.025mm 76 mm 500mm
DC Aluminium Foil for Hair Foil
The aluminum jumbo roll from heavy gauge aluminum foil to light gauge foil is
of wide applications. In food packaging, it has rich varieties, including
household foil, container foil, flexible packaging foil, Tetra Pak/Combi
packaging foil, beer sealing foil, etc.
In addition to food aluminum foil, it is also used as medicinal foil, cigarette foil,
hairdressing foil, and decorative foil for interior walls of buildings and interior
furniture. Other application fields include battery foil, battery soft foil, electronic
label foil, circuit board foil, aluminum foil for air-conditioning ducts,etc.

3. Light gauge foil can be further cut or painted as the hair foil. It is widely used in
hairdressing in Europe and America. It has a heat preservation effect, which
can shorten the time of hair treatment and avoid the pollution of hairdressing
chemicals.
The common used alloys are 1235 and 1200 DC aluminum foil. In terms of the
processing technology, do you know the differences between DC and CC
aluminum foil?
Compared with hot-rolled billets, the quality of cast-rolled billets is more difficult
to control. Since the deformation of aluminum foil rolled with cast-rolled billets
(thickness of 6-8mm) is much smaller, the quality of cast-rolled billets, such as
air passages, inclusions, segregation, coarse grains, and other defects, has a
greater impact on aluminum foil rolling quality.

4. If the electrolytic aluminum liquid is used to directly for the production of
aluminum foil blanks, the production process eliminates the casting and
remelting procedures of aluminum ingots, greatly reducing the energy
consumption of remelting and casting, and reducing the secondary remelting.
It has been widely used by smelting and processing enterprises.
However, due to the characteristics of electrolytic aluminum liquid, its injection
into the mixing furnace makes it difficult to formulate and control the
subsequent casting-rolling, cold-rolling, foil-rolling, annealing and other
production processes. Therefore, in the entire production process, the strict
control of the process are very important.
The aluminum foil blanks produced by the casting-rolling method and the
hot-rolling method have different mechanical properties during the aluminum
foil rolling process. The CC material has high strength, the rolling work
hardening speed is fast, and the final annealing performance of the aluminum
foil is also different.
After annealing at the same temperature and time, the aluminum foil produced
by CC material has high strength, while the aluminum foil produced by DC
material has low strength.
Therefore, to produce aluminum foil
with different blanks, different
rolling, slitting, and annealing
processes should be used.
Welcome to leave message below
to inquire 1200 aluminum foil for
hairdressing.
Cast-rolling method and hot-rolling
method have their own advantages
and disadvantages. The
casting-rolling method has short process flow and low cost, but it is only

5. suitable for some alloys and kinds.
The Manufacturing Process of Aluminum Jumbo Roll
Health and beauty is a big industry in many countries. Perm and hair dyeing
are familiar hairdressing methods for many women. Hair foil made of aluminum
jumbo roll is shorten the time of hair treatment and avoid the pollution of
hairdressing chemicals. What is its manufacturing process? Let’s have a look.
Aluminum foil production is an industry with high investment, high energy
consumption and high cost. During the aluminum foil manufacturing process,
the metal tends to be deformed due to a large friction force and a high
temperature produced by the high-speed rolling. Therefore, it is necessary to
add MOA-80 base oil( conventional rolling oil), which plays a role of lubrication
and cooling.
In the aluminum foil coiling process, the roughness of the shiny and dull side is
different. The dull side is relatively rough compared to the bright side. The
conventional rolling oil attached to the dark side of the aluminum foil is more
than the bright side.
Because the conventional rolling oil has high viscosity and wide distillation
range, it is not easy to volatilize during annealing. In addition, because of
different residue of rolling oil of different sides, usually the oil on the bright side
has been completely removed after a certain temperature and time, but the
dark side still has some. That will affects the surface quality of the aluminum

6. foil and has a serious impact on subsequent reprocessing.
To solve this problem, Haomei Aluminum the manufacturing process. We
choose to spray conventional rolling oil during rough rolling, intermediate
rolling and finishing rolling, and spray low flash point rolling oil during the
winding process. The use of low flash point rolling oil can effectively reduce the
interlayer friction coefficient caused by metal deformation during rolling and
reduce the number of pinholes in the aluminum foil.
More importantly, during the annealing process, due to the the low flash point
rolling oil’s short distillation range and low initial and final distillation
temperature, it is easy to anneal and remove oil, thereby reducing annealing
time, greatly improving equipment utilization, and reducing production costs.