4. How to reduce Ground Bounce Reduction on PCBAs.pdf
•
0 likes•2 views
How to reduce Ground Bounce Reduction on PCBAs 1. Minimize return paths The shorter the return paths, the lower the inductance between components and the ground plane. Therefore, digital components should be placed directly over digital ground areas and mixed-signal devices should be positioned above bridges between digital and analog ground areas, whenever possible. 2. Use short component leads Using packages with shorter component leads reduces the series inductance. This is also accomplished by using BGAs and vias. Decoupling capacitors should also be used to funnel disturbances to ground as quickly as possible. It is probably a good idea to use these for all IC and transistor ground pins. 3. Use multiple vias Another way to quickly dissipate disturbances or noise from your circuits is to use multiple vias to route to ground. 4. Offset switching, if possible The parasitics that cause ground bounce may not be able to be completely eliminated; however, by offsetting switching times, you can minimize the extent or magnitude of the ground bounce. 5. Use slower switching components, if possible This technique should be used in conjunction with offsets to allow damping to occur prior to the next switching event. This will prevent it from being added to the noise that may be already present. If you have request, contact Cynthia at sales11@hitechpcb.com
Report
Share
Report
Share
Download to read offline
Recommended
Circuit Board Layout Techniques - www.circuitsinc.tk
This document provides guidelines for laying out analog circuit boards to minimize noise. It recommends using multilayer boards with separate analog and digital ground and power planes. Traces should be short and avoid loops or 90 degree turns. Digital signals should be routed away from analog components. Bypass capacitors are needed at power inputs and op amps to filter different frequency ranges. Following these techniques can help reduce conducted and radiated noise by 20 decibels or more.
12 wp5 slides_authors_dp_dec_26_2012
This document summarizes a presentation on reducing digital to RF crosstalk in PCB designs with antennas. It discusses challenges in PCB antenna design due to noise coupling and examines techniques to reduce coupling, such as partitioning boards by component interfaces, minimizing return path discontinuities, and applying phase shifts between digital buses. Simulation is used to analyze noise sources, identify failure points, and optimize designs through multiple iterations. Reducing interaction between antenna and digital interface return currents can lower crosstalk.
Bt31482484
This document summarizes some key challenges for digital circuits related to process, voltage, and temperature variations. It discusses techniques to prevent latchup and electrostatic discharge issues in integrated circuits. It also describes simultaneous switching noise that can occur when large numbers of circuits switch simultaneously. The document proposes using adaptive body biasing techniques to compensate for PVT variations and control output slope under different conditions. Simulation results show this approach can adjust rising and falling times of an output buffer for different substrate bias voltage conditions.
In building solution module 2.2
This document provides contact information for Sumon Saha of IBS Planning & Optimization at Grameenphone Limited. It also contains summaries of passive materials used for in-building wireless networks like coaxial cable, jumper cables, leaky feeders, connectors, trays, and antennas. Guidelines are provided for technical surveys of indoor wireless sites, including necessary tools, goals of collecting coverage and capacity information, and steps like taking photos, collecting GPS coordinates, understanding architecture and requirements, selecting equipment positions and feeder paths.
Emi emc design guide lines
General guidelines for design and review based on EEMI EMC free products. Product performance improvement in initial design stage
Simple Wireless Radio Data Link
This summarizes a document describing a simple wireless data link design between two computers using radio frequency transmission. It consists of a transmitter circuit built with inexpensive components that is connected to a computer's serial port to transmit data. On the receiving end, a standard FM radio is used but requires modification to extract the digital signal from the discriminator circuit for decoding by a receiver circuit. The design was able to reliably transmit data at 19.2 kbps over short ranges of around 20 meters.
Timing and synchronization for 5G over optical networks
At OFC, Nir Laufer reviewed the options for delivering accurate timing using PTP and SyncE over OTN/WDM networks. The presentation focused on robust mechanisms for delivering unprecedented levels of precision synchronization, including how a dedicated out-of-band optical timing channel can be leveraged to overcome technical and economical challenges and provide sub-100nsec accuracy.
AN102_ANTENNA_DESIGN_FEB_11.pdf
The document discusses different types of small antennas that can be used for EnOcean-based products, including quarter-wave monopole antennas, helical antennas, chip antennas, and PCB antennas. It emphasizes that the antenna design is critical for RF performance and range. A quarter-wave monopole antenna provides good overall performance but may be too long at lower frequencies. A helical antenna can significantly reduce the size while maintaining good performance. PCB antennas can be a low-cost solution if enough ground plane is available. The size and shape of the ground plane is important for all these antenna types to function properly.
Recommended
Circuit Board Layout Techniques - www.circuitsinc.tk
This document provides guidelines for laying out analog circuit boards to minimize noise. It recommends using multilayer boards with separate analog and digital ground and power planes. Traces should be short and avoid loops or 90 degree turns. Digital signals should be routed away from analog components. Bypass capacitors are needed at power inputs and op amps to filter different frequency ranges. Following these techniques can help reduce conducted and radiated noise by 20 decibels or more.
12 wp5 slides_authors_dp_dec_26_2012
This document summarizes a presentation on reducing digital to RF crosstalk in PCB designs with antennas. It discusses challenges in PCB antenna design due to noise coupling and examines techniques to reduce coupling, such as partitioning boards by component interfaces, minimizing return path discontinuities, and applying phase shifts between digital buses. Simulation is used to analyze noise sources, identify failure points, and optimize designs through multiple iterations. Reducing interaction between antenna and digital interface return currents can lower crosstalk.
Bt31482484
This document summarizes some key challenges for digital circuits related to process, voltage, and temperature variations. It discusses techniques to prevent latchup and electrostatic discharge issues in integrated circuits. It also describes simultaneous switching noise that can occur when large numbers of circuits switch simultaneously. The document proposes using adaptive body biasing techniques to compensate for PVT variations and control output slope under different conditions. Simulation results show this approach can adjust rising and falling times of an output buffer for different substrate bias voltage conditions.
In building solution module 2.2
This document provides contact information for Sumon Saha of IBS Planning & Optimization at Grameenphone Limited. It also contains summaries of passive materials used for in-building wireless networks like coaxial cable, jumper cables, leaky feeders, connectors, trays, and antennas. Guidelines are provided for technical surveys of indoor wireless sites, including necessary tools, goals of collecting coverage and capacity information, and steps like taking photos, collecting GPS coordinates, understanding architecture and requirements, selecting equipment positions and feeder paths.
Emi emc design guide lines
General guidelines for design and review based on EEMI EMC free products. Product performance improvement in initial design stage
Simple Wireless Radio Data Link
This summarizes a document describing a simple wireless data link design between two computers using radio frequency transmission. It consists of a transmitter circuit built with inexpensive components that is connected to a computer's serial port to transmit data. On the receiving end, a standard FM radio is used but requires modification to extract the digital signal from the discriminator circuit for decoding by a receiver circuit. The design was able to reliably transmit data at 19.2 kbps over short ranges of around 20 meters.
Timing and synchronization for 5G over optical networks
At OFC, Nir Laufer reviewed the options for delivering accurate timing using PTP and SyncE over OTN/WDM networks. The presentation focused on robust mechanisms for delivering unprecedented levels of precision synchronization, including how a dedicated out-of-band optical timing channel can be leveraged to overcome technical and economical challenges and provide sub-100nsec accuracy.
AN102_ANTENNA_DESIGN_FEB_11.pdf
The document discusses different types of small antennas that can be used for EnOcean-based products, including quarter-wave monopole antennas, helical antennas, chip antennas, and PCB antennas. It emphasizes that the antenna design is critical for RF performance and range. A quarter-wave monopole antenna provides good overall performance but may be too long at lower frequencies. A helical antenna can significantly reduce the size while maintaining good performance. PCB antennas can be a low-cost solution if enough ground plane is available. The size and shape of the ground plane is important for all these antenna types to function properly.
Monopole
The document discusses various types of small antennas that can be used for EnOcean-based products, including quarter-wave monopole antennas, helical antennas, chip antennas, and PCB antennas. It emphasizes that the antenna design is critical for radio performance and range. The antenna and a sufficiently sized ground plane form a resonant circuit. Common pitfalls in antenna design are an undersized ground plane or traces and components placed too close to the antenna.
04299154
This document presents a high gain printed ultra wideband antenna concept covering 3-10 GHz. It summarizes a printed antenna design with circular dipole radiation elements fed by a planar printed circuit. A metallic reflector is used to shape the radiation pattern, providing a half-space radiation pattern in azimuth and moderate beamwidth in elevation. Simulation and measurement results show the antenna achieves a gain of 7-8 dBi across the band with a 180 degree azimuth beamwidth. The design offers a low-cost, easily integrated solution and was tested in a vehicle entertainment application.
8 wireless part b
The document discusses Cisco wireless LAN technologies and configurations. It covers topics such as wired vs wireless networks, wireless bands and channels, encryption methods, Cisco wireless LAN controller deployment models, and wireless service sets. Cisco offers different wireless LAN controller deployment models including centralized, cloud-based, embedded, and mobility express, suitable for different network sizes. Wireless networks use radio frequencies to transmit data without wires, dividing frequency bands into non-overlapping channels to allow multiple access points to operate simultaneously without interference.
Newtec FlexACM
This white paper compares two technologies for optimizing satellite capacity efficiency for IP trunking networks: adaptive coding and modulation (ACM) and signal cancellation. It analyzes a reference network delivering symmetrical and asymmetrical services from a hub in Sudan to 10 remote sites in Africa. Using conventional fixed modulation, a minimum of 3 transponders is needed for symmetrical services but asymmetrical services require too much bandwidth to fit in two transponders. The paper will evaluate if ACM or signal cancellation can provide bandwidth savings.
Newtec - Optimisation of Satellite Capacity Efficiency for IP Trunking Applic...
This white paper compares two technologies for optimizing satellite capacity efficiency for IP trunking networks: adaptive coding and modulation (ACM) and signal cancellation. It analyzes a reference network delivering symmetrical and asymmetrical services from a hub in Sudan to 10 remote sites in Africa. Using conventional fixed modulation, a minimum of 3 transponders is needed for symmetrical services but asymmetrical services require too much bandwidth to fit in two transponders. The paper will evaluate if ACM or signal cancellation can provide a more efficient implementation.
Power Gating Based Ground Bounce Noise Reduction
As low power circuits are most popular the decrease in supply voltage leads to increase in leakage power with respect to the technology scaling. So for removing this kind of leakages and to provide a better power efficiency many power gating techniques are used. But the leakage due to ground connection to the active part of the circuit is very high rather than all other leakages. As it is mainly due to the back EMF of the ground connection it was called it as ground bounce noise. To reduce this noise different methodologies are designed. In this paper the design of such an efficient technique related to ground bounce noise reduction using power gating circuits and comparing the results using DSCH and Microwind low power tools. In this paper the analysis of adders such as full adders using different types of power gated circuits using low power VLSI design techniques and to present the comparison results between different power gating methods.
GPS Timing_The Cell Site
Global positioning timing is essential for mobile call processing and handoffs between cell sites. Precise timing is maintained between sites to within 1 millisecond or even 1 microsecond. GPS signals contain pseudo-random codes that help receivers synchronize to within trillionths of a second. The GPS antenna requires a clear view of the sky and should be installed within 100 feet of the GPS equipment using a special low-loss cable. Correct antenna placement and installation of a ground plane are important to minimize signal degradation.
High performance domino full adder design under different body biased technology
This document presents the design and analysis of different body-biased domino full adder circuits at 150nm and 45nm technologies. Six different body biasing schemes are proposed and their performance is compared in terms of power consumption, delay, and noise. Simulation results show that connecting the NMOS substrate to its source and the PMOS substrate to the clock (SB6 biasing) provides the best performance with minimum power consumption and delay. This design is shown to be effective across both technology nodes, indicating technology independence. Overall, the document evaluates body biasing techniques for optimizing domino logic circuits at reduced technology scales.
Gas insulated substation.
The document summarizes a seminar presentation on gas insulated substations (GIS). It defines GIS as substations that use sulfur hexafluoride gas (SF6) as an insulating medium to allow for a compact design. The document outlines the key internal equipment of GIS, including circuit breakers, disconnectors, buses, transformers, and more. It discusses the advantages of GIS such as reduced space requirements and reliability. GIS are well-suited for applications requiring a small footprint, such as urban or indoor installations.
8 wireless parta v1
This document provides an overview of key topics in wireless networking, including the differences between wired and wireless networks, wireless technologies, basic service sets (BSS), radio frequency (RF), wireless bands and channels, and wireless encryption. It discusses how wireless networks remove the need for wires but introduce challenges with transmitting data through open space without physical protection. Access points and BSSIDs are described as creating closed wireless groups with a common standard and coverage area.
FUNDAMENTALS OF MICROWAVE RADIO COMMUNICATION FOR IP AND TDM
1) The document provides an introduction to microwave radio communication fundamentals and IP applications. It discusses topics such as microwave spectrum, terrestrial microwave links and applications, microwave range, how microwave radios communicate, and extenders range with repeaters.
2) It then covers Layer 2 radio technology, the importance of propagation analysis, antennas and feeder systems, and RF protection. Diagrams and examples are provided to illustrate key concepts.
3) The goal is to provide network engineers an understanding of microwave fundamentals needed to design carrier Ethernet and IP microwave networks that transport voice, data, and online media with requirements for quality of service and reliability.
FUNDAMENTALS OF HIGH SPEED DESIGN.pdf
This document discusses fundamentals of high speed PCB design. It covers topics like what constitutes a high speed design, signal propagation, transmission lines, impedance matching, stackup selection, routing guidelines, and do's/don'ts. Key aspects addressed include maintaining consistent impedance, minimizing reflections, controlling skew, ensuring return current paths, and using proper termination and vias. Designing high speed circuits requires attention to these factors to optimize signal integrity.
Sub-100ns accuracy at cell sites over commercial WDM networks
In his ITSF 2020 presentation, Nir Laufer explained how robust timing with nanosecond precision can be achieved by delivering timing over PTP-optimized optical transport channels. He discussed tackling GNSS vulnerabilities – including the growing threat of jamming and spoofing attacks – by ensuring robust backup from ePRTC core clocks to the aggregation site.
IRJET - 5G Architecture using GAN based Digital Transmitter in VLSI Desig...
This document discusses the design of a 5G architecture using a fully digital transmitter chain with a GaN-based digital power amplifier and low pass filter in VLSI design. A digital transmitter chain converts the baseband signal into a binary bit stream, which is amplified and filtered to reconstruct the analog output signal. The transition to a fully digital design approach allows for reduced size, increased reconfigurability, improved frequency flexibility and power savings compared to traditional analog transmitters. The key components discussed are the switch-mode power amplifier using GaN, a output low pass filter to reconstruct the analog signal from the amplified binary output, and a modulator implemented using digital logic for high efficiency and integrated digital predistortion capabilities. Simulation results show the design
Reconfigurable C and Ku band antenna Using Duelpatch
This document describes the design of a reconfigurable C and Ku band antenna using a dual-patch structure. The antenna can operate at 4, 5, 10, and 12 GHz bands by using two C-slots and two PIN diode switches to independently control the patch elements. When one patch is switched on and the other off, different frequency sets are achieved. Simulations show the antenna achieves 500 MHz bandwidth in the C-band and 1 GHz bandwidth in the Ku-band. The compact antenna size of 80x60x1.57mm makes it suitable for applications such as satellite TV reception and WLAN. Challenges in the design include impedance matching between elements and mutual coupling between closely spaced patches.
PMC_6G
This document describes a 4.9-6.4 Gb/s transceiver designed for backplane communications. It uses an adaptive decision feedback equalizer and achieves bit error rates below 10-15 over a 34-inch legacy FR4 backplane. Key components include a phase locked loop for clock synthesis, a transmitter with single-tap pre-emphasis, and a receiver with adaptive equalization and digital clock recovery. Measurement results demonstrate error-free performance over various backplane lengths.
Sprabj7
This document provides guidelines for designing the printed circuit board (PCB) power distribution network (PDN) for TI OMAP3630, AM37xx, and DM37xx microprocessors. It outlines a 5-step methodology: 1) Requirements for the PCB stackup, 2) Optimizing the physical layout, 3) Static IR drop analysis, 4) AC analysis, and 5) Design checklist. Key recommendations include closely coupling power and ground planes, minimizing dielectric thickness, and optimizing via and trace routing to reduce parasitic inductance and improve high-frequency performance.
An Aperture Coupled Printed Antenna for Broadband Radio Services
1) The document describes the design and simulation of an aperture coupled microstrip patch antenna for broadband radio services.
2) The antenna is designed to resonate at 2.56 GHz using an aperture coupling technique for improved isolation and lower cross polarization.
3) Simulation results show the antenna has a return loss of -24.5 dB at 2.56 GHz with a 140 MHz bandwidth, a maximum gain of 3.08 dBi, and radiation patterns suitable for broadband applications.
AinaBpresentation29122020_bh 06012021.pptx
The document discusses a hybrid phase shift beamforming technique that combines true time delay and phase shift approaches to mitigate beam squint over wide bandwidths. This technique is well-suited for 5G communications and wideband radar applications by improving accuracy and sensitivity. A comparison is made between traditional electronic phase shifters and proposed photonic integrated optical phase shifters, finding advantages in the optical approach such as wider bandwidth, higher resolution, lower power consumption and faster switching. Challenges with conventional electronic beamforming are outlined along with specifications for a proposed hybrid photonic/electronic architecture intended to overcome these limitations and enable applications such as indoor 5G and radar beam steering.
Identify and explain key technologies for evolutionary change in spa.pdf
Identify and explain key technologies for evolutionary change in spaceborne communications.
Solution
The Air Force should invest in those satellite communications technologies unavailable in the
commercial sector that are critical for military-specific, core communications services; other
technologies and services can be adapted from commercial practice. From the foregoing
discussion these critical technologies are:
• Antenna systems that efficiently direct downlink power to users (even at unplanned locations)
and reject jamming on the uplinks by use of multi-beam, real-time adaptive antenna patterns
• Very high-rate (many gigabits per second) communications for sensor data relay and
dissemination among spacecraft, airplanes, and ground sites; optical communications is the
method of choice
• Onboard processing for jamming protection that despreads and demodulates uplink signals and
routes them to appropriate downlinks, providing interconnection of disparate users (including
packet communications)
The present state of practice for advanced antenna arrays is to use global spot multibeam routing
and switching. However, recent advances on antenna arrays have provided limited adaptive beam
forming. Based on the present development, a 3 Gbps data throughput rate should be achievable
on satellites before the end of the century. It will be necessary to continue shifting the RF
communication band to a higher frequency with wider bandwidth to obtain increased data rates.
Therefore, it is essential to continue to develop the electronics required to send telemetry at a
higher operating frequency.
The use of real-time adaptive beam patterns on up-link and down-link on communications
satellites has been very limited. Today, commercial satellites have multiple beams, but they are
usually fixed in anticipation of a particular orbital location and an intended customer base. For
military communications, neither of these is likely since the theater of operations is
scenariodependent. The ability to create multiple narrow-beam downlinks allows the satellite
transmitter power to be directed only to the intended users, as well as permitting frequency re-
use (important in the crowded spectrum allocations). Both factors result in increased capacity
through the satellite. The ability to create multiple narrow-beam uplinks provides high receiving
gain that in turn allows either smaller earth terminals to close the link or higher data rates to be
transmitted. Substantial reductions in ground terminal costs will result. More importantly,
narrow-beam uplinks can be used to reject interfering sources (jammers) out-of-beam, and,
through combining of multiple beams, to reject jamming sources within a beamwidth. The ability
to do such realtime adaptive antenna beam formation to create very deep, narrow nulls anywhere
within the field of view of the satellite over the very wide bandwidths necessary for AJ
modulation is not something that the commercial sector will develop (c.
Best Competitive Marble Pricing in Dubai - ☎ 9928909666
Stone Art Hub offers the best competitive Marble Pricing in Dubai, ensuring affordability without compromising quality. With a wide range of exquisite marble options to choose from, you can enhance your spaces with elegance and sophistication. For inquiries or orders, contact us at ☎ 9928909666. Experience luxury at unbeatable prices.
4 Benefits of Partnering with an OnlyFans Agency for Content Creators.pdf
In the competitive world of content creation, standing out and maximising revenue on platforms like OnlyFans can be challenging. This is where partnering with an OnlyFans agency can make a significant difference. Here are five key benefits for content creators considering this option:
More Related Content
Similar to 4. How to reduce Ground Bounce Reduction on PCBAs.pdf
Monopole
The document discusses various types of small antennas that can be used for EnOcean-based products, including quarter-wave monopole antennas, helical antennas, chip antennas, and PCB antennas. It emphasizes that the antenna design is critical for radio performance and range. The antenna and a sufficiently sized ground plane form a resonant circuit. Common pitfalls in antenna design are an undersized ground plane or traces and components placed too close to the antenna.
04299154
This document presents a high gain printed ultra wideband antenna concept covering 3-10 GHz. It summarizes a printed antenna design with circular dipole radiation elements fed by a planar printed circuit. A metallic reflector is used to shape the radiation pattern, providing a half-space radiation pattern in azimuth and moderate beamwidth in elevation. Simulation and measurement results show the antenna achieves a gain of 7-8 dBi across the band with a 180 degree azimuth beamwidth. The design offers a low-cost, easily integrated solution and was tested in a vehicle entertainment application.
8 wireless part b
The document discusses Cisco wireless LAN technologies and configurations. It covers topics such as wired vs wireless networks, wireless bands and channels, encryption methods, Cisco wireless LAN controller deployment models, and wireless service sets. Cisco offers different wireless LAN controller deployment models including centralized, cloud-based, embedded, and mobility express, suitable for different network sizes. Wireless networks use radio frequencies to transmit data without wires, dividing frequency bands into non-overlapping channels to allow multiple access points to operate simultaneously without interference.
Newtec FlexACM
This white paper compares two technologies for optimizing satellite capacity efficiency for IP trunking networks: adaptive coding and modulation (ACM) and signal cancellation. It analyzes a reference network delivering symmetrical and asymmetrical services from a hub in Sudan to 10 remote sites in Africa. Using conventional fixed modulation, a minimum of 3 transponders is needed for symmetrical services but asymmetrical services require too much bandwidth to fit in two transponders. The paper will evaluate if ACM or signal cancellation can provide bandwidth savings.
Newtec - Optimisation of Satellite Capacity Efficiency for IP Trunking Applic...
This white paper compares two technologies for optimizing satellite capacity efficiency for IP trunking networks: adaptive coding and modulation (ACM) and signal cancellation. It analyzes a reference network delivering symmetrical and asymmetrical services from a hub in Sudan to 10 remote sites in Africa. Using conventional fixed modulation, a minimum of 3 transponders is needed for symmetrical services but asymmetrical services require too much bandwidth to fit in two transponders. The paper will evaluate if ACM or signal cancellation can provide a more efficient implementation.
Power Gating Based Ground Bounce Noise Reduction
As low power circuits are most popular the decrease in supply voltage leads to increase in leakage power with respect to the technology scaling. So for removing this kind of leakages and to provide a better power efficiency many power gating techniques are used. But the leakage due to ground connection to the active part of the circuit is very high rather than all other leakages. As it is mainly due to the back EMF of the ground connection it was called it as ground bounce noise. To reduce this noise different methodologies are designed. In this paper the design of such an efficient technique related to ground bounce noise reduction using power gating circuits and comparing the results using DSCH and Microwind low power tools. In this paper the analysis of adders such as full adders using different types of power gated circuits using low power VLSI design techniques and to present the comparison results between different power gating methods.
GPS Timing_The Cell Site
Global positioning timing is essential for mobile call processing and handoffs between cell sites. Precise timing is maintained between sites to within 1 millisecond or even 1 microsecond. GPS signals contain pseudo-random codes that help receivers synchronize to within trillionths of a second. The GPS antenna requires a clear view of the sky and should be installed within 100 feet of the GPS equipment using a special low-loss cable. Correct antenna placement and installation of a ground plane are important to minimize signal degradation.
High performance domino full adder design under different body biased technology
This document presents the design and analysis of different body-biased domino full adder circuits at 150nm and 45nm technologies. Six different body biasing schemes are proposed and their performance is compared in terms of power consumption, delay, and noise. Simulation results show that connecting the NMOS substrate to its source and the PMOS substrate to the clock (SB6 biasing) provides the best performance with minimum power consumption and delay. This design is shown to be effective across both technology nodes, indicating technology independence. Overall, the document evaluates body biasing techniques for optimizing domino logic circuits at reduced technology scales.
Gas insulated substation.
The document summarizes a seminar presentation on gas insulated substations (GIS). It defines GIS as substations that use sulfur hexafluoride gas (SF6) as an insulating medium to allow for a compact design. The document outlines the key internal equipment of GIS, including circuit breakers, disconnectors, buses, transformers, and more. It discusses the advantages of GIS such as reduced space requirements and reliability. GIS are well-suited for applications requiring a small footprint, such as urban or indoor installations.
8 wireless parta v1
This document provides an overview of key topics in wireless networking, including the differences between wired and wireless networks, wireless technologies, basic service sets (BSS), radio frequency (RF), wireless bands and channels, and wireless encryption. It discusses how wireless networks remove the need for wires but introduce challenges with transmitting data through open space without physical protection. Access points and BSSIDs are described as creating closed wireless groups with a common standard and coverage area.
FUNDAMENTALS OF MICROWAVE RADIO COMMUNICATION FOR IP AND TDM
1) The document provides an introduction to microwave radio communication fundamentals and IP applications. It discusses topics such as microwave spectrum, terrestrial microwave links and applications, microwave range, how microwave radios communicate, and extenders range with repeaters.
2) It then covers Layer 2 radio technology, the importance of propagation analysis, antennas and feeder systems, and RF protection. Diagrams and examples are provided to illustrate key concepts.
3) The goal is to provide network engineers an understanding of microwave fundamentals needed to design carrier Ethernet and IP microwave networks that transport voice, data, and online media with requirements for quality of service and reliability.
FUNDAMENTALS OF HIGH SPEED DESIGN.pdf
This document discusses fundamentals of high speed PCB design. It covers topics like what constitutes a high speed design, signal propagation, transmission lines, impedance matching, stackup selection, routing guidelines, and do's/don'ts. Key aspects addressed include maintaining consistent impedance, minimizing reflections, controlling skew, ensuring return current paths, and using proper termination and vias. Designing high speed circuits requires attention to these factors to optimize signal integrity.
Sub-100ns accuracy at cell sites over commercial WDM networks
In his ITSF 2020 presentation, Nir Laufer explained how robust timing with nanosecond precision can be achieved by delivering timing over PTP-optimized optical transport channels. He discussed tackling GNSS vulnerabilities – including the growing threat of jamming and spoofing attacks – by ensuring robust backup from ePRTC core clocks to the aggregation site.
IRJET - 5G Architecture using GAN based Digital Transmitter in VLSI Desig...
This document discusses the design of a 5G architecture using a fully digital transmitter chain with a GaN-based digital power amplifier and low pass filter in VLSI design. A digital transmitter chain converts the baseband signal into a binary bit stream, which is amplified and filtered to reconstruct the analog output signal. The transition to a fully digital design approach allows for reduced size, increased reconfigurability, improved frequency flexibility and power savings compared to traditional analog transmitters. The key components discussed are the switch-mode power amplifier using GaN, a output low pass filter to reconstruct the analog signal from the amplified binary output, and a modulator implemented using digital logic for high efficiency and integrated digital predistortion capabilities. Simulation results show the design
Reconfigurable C and Ku band antenna Using Duelpatch
This document describes the design of a reconfigurable C and Ku band antenna using a dual-patch structure. The antenna can operate at 4, 5, 10, and 12 GHz bands by using two C-slots and two PIN diode switches to independently control the patch elements. When one patch is switched on and the other off, different frequency sets are achieved. Simulations show the antenna achieves 500 MHz bandwidth in the C-band and 1 GHz bandwidth in the Ku-band. The compact antenna size of 80x60x1.57mm makes it suitable for applications such as satellite TV reception and WLAN. Challenges in the design include impedance matching between elements and mutual coupling between closely spaced patches.
PMC_6G
This document describes a 4.9-6.4 Gb/s transceiver designed for backplane communications. It uses an adaptive decision feedback equalizer and achieves bit error rates below 10-15 over a 34-inch legacy FR4 backplane. Key components include a phase locked loop for clock synthesis, a transmitter with single-tap pre-emphasis, and a receiver with adaptive equalization and digital clock recovery. Measurement results demonstrate error-free performance over various backplane lengths.
Sprabj7
This document provides guidelines for designing the printed circuit board (PCB) power distribution network (PDN) for TI OMAP3630, AM37xx, and DM37xx microprocessors. It outlines a 5-step methodology: 1) Requirements for the PCB stackup, 2) Optimizing the physical layout, 3) Static IR drop analysis, 4) AC analysis, and 5) Design checklist. Key recommendations include closely coupling power and ground planes, minimizing dielectric thickness, and optimizing via and trace routing to reduce parasitic inductance and improve high-frequency performance.
An Aperture Coupled Printed Antenna for Broadband Radio Services
1) The document describes the design and simulation of an aperture coupled microstrip patch antenna for broadband radio services.
2) The antenna is designed to resonate at 2.56 GHz using an aperture coupling technique for improved isolation and lower cross polarization.
3) Simulation results show the antenna has a return loss of -24.5 dB at 2.56 GHz with a 140 MHz bandwidth, a maximum gain of 3.08 dBi, and radiation patterns suitable for broadband applications.
AinaBpresentation29122020_bh 06012021.pptx
The document discusses a hybrid phase shift beamforming technique that combines true time delay and phase shift approaches to mitigate beam squint over wide bandwidths. This technique is well-suited for 5G communications and wideband radar applications by improving accuracy and sensitivity. A comparison is made between traditional electronic phase shifters and proposed photonic integrated optical phase shifters, finding advantages in the optical approach such as wider bandwidth, higher resolution, lower power consumption and faster switching. Challenges with conventional electronic beamforming are outlined along with specifications for a proposed hybrid photonic/electronic architecture intended to overcome these limitations and enable applications such as indoor 5G and radar beam steering.
Identify and explain key technologies for evolutionary change in spa.pdf
Identify and explain key technologies for evolutionary change in spaceborne communications.
Solution
The Air Force should invest in those satellite communications technologies unavailable in the
commercial sector that are critical for military-specific, core communications services; other
technologies and services can be adapted from commercial practice. From the foregoing
discussion these critical technologies are:
• Antenna systems that efficiently direct downlink power to users (even at unplanned locations)
and reject jamming on the uplinks by use of multi-beam, real-time adaptive antenna patterns
• Very high-rate (many gigabits per second) communications for sensor data relay and
dissemination among spacecraft, airplanes, and ground sites; optical communications is the
method of choice
• Onboard processing for jamming protection that despreads and demodulates uplink signals and
routes them to appropriate downlinks, providing interconnection of disparate users (including
packet communications)
The present state of practice for advanced antenna arrays is to use global spot multibeam routing
and switching. However, recent advances on antenna arrays have provided limited adaptive beam
forming. Based on the present development, a 3 Gbps data throughput rate should be achievable
on satellites before the end of the century. It will be necessary to continue shifting the RF
communication band to a higher frequency with wider bandwidth to obtain increased data rates.
Therefore, it is essential to continue to develop the electronics required to send telemetry at a
higher operating frequency.
The use of real-time adaptive beam patterns on up-link and down-link on communications
satellites has been very limited. Today, commercial satellites have multiple beams, but they are
usually fixed in anticipation of a particular orbital location and an intended customer base. For
military communications, neither of these is likely since the theater of operations is
scenariodependent. The ability to create multiple narrow-beam downlinks allows the satellite
transmitter power to be directed only to the intended users, as well as permitting frequency re-
use (important in the crowded spectrum allocations). Both factors result in increased capacity
through the satellite. The ability to create multiple narrow-beam uplinks provides high receiving
gain that in turn allows either smaller earth terminals to close the link or higher data rates to be
transmitted. Substantial reductions in ground terminal costs will result. More importantly,
narrow-beam uplinks can be used to reject interfering sources (jammers) out-of-beam, and,
through combining of multiple beams, to reject jamming sources within a beamwidth. The ability
to do such realtime adaptive antenna beam formation to create very deep, narrow nulls anywhere
within the field of view of the satellite over the very wide bandwidths necessary for AJ
modulation is not something that the commercial sector will develop (c.
Similar to 4. How to reduce Ground Bounce Reduction on PCBAs.pdf (20)
Newtec - Optimisation of Satellite Capacity Efficiency for IP Trunking Applic...
Newtec - Optimisation of Satellite Capacity Efficiency for IP Trunking Applic...
High performance domino full adder design under different body biased technology
High performance domino full adder design under different body biased technology
FUNDAMENTALS OF MICROWAVE RADIO COMMUNICATION FOR IP AND TDM
FUNDAMENTALS OF MICROWAVE RADIO COMMUNICATION FOR IP AND TDM
Sub-100ns accuracy at cell sites over commercial WDM networks
Sub-100ns accuracy at cell sites over commercial WDM networks
IRJET - 5G Architecture using GAN based Digital Transmitter in VLSI Desig...
IRJET - 5G Architecture using GAN based Digital Transmitter in VLSI Desig...
Reconfigurable C and Ku band antenna Using Duelpatch
Reconfigurable C and Ku band antenna Using Duelpatch
An Aperture Coupled Printed Antenna for Broadband Radio Services
An Aperture Coupled Printed Antenna for Broadband Radio Services
Identify and explain key technologies for evolutionary change in spa.pdf
Identify and explain key technologies for evolutionary change in spa.pdf
Recently uploaded
Best Competitive Marble Pricing in Dubai - ☎ 9928909666
Stone Art Hub offers the best competitive Marble Pricing in Dubai, ensuring affordability without compromising quality. With a wide range of exquisite marble options to choose from, you can enhance your spaces with elegance and sophistication. For inquiries or orders, contact us at ☎ 9928909666. Experience luxury at unbeatable prices.
4 Benefits of Partnering with an OnlyFans Agency for Content Creators.pdf
In the competitive world of content creation, standing out and maximising revenue on platforms like OnlyFans can be challenging. This is where partnering with an OnlyFans agency can make a significant difference. Here are five key benefits for content creators considering this option:
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
This letter, written by Kellen Harkins, Course Director at Full Sail University, commends Anny Love's exemplary performance in the Video Sharing Platforms class. It highlights her dedication, willingness to challenge herself, and exceptional skills in production, editing, and marketing across various video platforms like YouTube, TikTok, and Instagram.
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Transport Solution
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
Nathalie zal delen hoe DEI en ESG een fundamentele rol kunnen spelen in je merkstrategie en je de juiste aansluiting kan creëren met je doelgroep. Door middel van voorbeelden en simpele handvatten toont ze hoe dit in jouw organisatie toegepast kan worden.
Best Forex Brokers Comparison in INDIA 2024
Navigating the world of forex trading can be challenging, especially for beginners. To help you make an informed decision, we have comprehensively compared the best forex brokers in India for 2024. This article, reviewed by Top Forex Brokers Review, will cover featured award winners, the best forex brokers, featured offers, the best copy trading platforms, the best forex brokers for beginners, the best MetaTrader brokers, and recently updated reviews. We will focus on FP Markets, Black Bull, EightCap, IC Markets, and Octa.
Income Tax exemption for Start up : Section 80 IAC
A presentation on the concept of Exemption of Profits of Start ups from Income Tax
How HR Search Helps in Company Success.pdf
HR search is critical to a company's success because it ensures the correct people are in place. HR search integrates workforce capabilities with company goals by painstakingly identifying, screening, and employing qualified candidates, supporting innovation, productivity, and growth. Efficient talent acquisition improves teamwork while encouraging collaboration. Also, it reduces turnover, saves money, and ensures consistency. Furthermore, HR search discovers and develops leadership potential, resulting in a strong pipeline of future leaders. Finally, this strategic approach to recruitment enables businesses to respond to market changes, beat competitors, and achieve long-term success.
Satta Matka Dpboss Matka Guessing Kalyan Chart Indian Matka Kalyan panel Chart
Satta Matka Dpboss Matka Guessing Kalyan Chart Indian Matka Kalyan panel Chart➒➌➎➏➑➐➋➑➐➐Dpboss Matka Guessing Satta Matka Kalyan Chart Indian Matka
SATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSThe Genesis of BriansClub.cm Famous Dark WEb Platform
BriansClub.cm, a famous platform on the dark web, has become one of the most infamous carding marketplaces, specializing in the sale of stolen credit card data.
Digital Marketing with a Focus on Sustainability
Digital Marketing best practices including influencer marketing, content creators, and omnichannel marketing for Sustainable Brands at the Sustainable Cosmetics Summit 2024 in New York
TIMES BPO: Business Plan For Startup Industry
Starting a business is like embarking on an unpredictable adventure. It’s a journey filled with highs and lows, victories and defeats. But what if I told you that those setbacks and failures could be the very stepping stones that lead you to fortune? Let’s explore how resilience, adaptability, and strategic thinking can transform adversity into opportunity.
Negotiation & Presentation Skills regarding steps in business communication, ...
Business Communication & presentation Skills, Negotiation Skills
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...➒➌➎➏➑➐➋➑➐➐Dpboss Matka Guessing Satta Matka Kalyan Chart Indian Matka
Sattamatka.satta.matka.satta matka.kalyan weekly chart.kalyan chart.kalyan jodi chart.kalyan penal chart.kalyan today.kalyan open.fix satta.fix fix fix Satta matka nambarPart 2 Deep Dive: Navigating the 2024 Slowdown
Introduction
The global retail industry has weathered numerous storms, with the financial crisis of 2008 serving as a poignant reminder of the sector's resilience and adaptability. However, as we navigate the complex landscape of 2024, retailers face a unique set of challenges that demand innovative strategies and a fundamental shift in mindset. This white paper contrasts the impact of the 2008 recession on the retail sector with the current headwinds retailers are grappling with, while offering a comprehensive roadmap for success in this new paradigm.
Innovation Management Frameworks: Your Guide to Creativity & Innovation
Innovation Management Frameworks: Your Guide to Creativity & InnovationOperational Excellence Consulting
[To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
This PowerPoint compilation offers a comprehensive overview of 20 leading innovation management frameworks and methodologies, selected for their broad applicability across various industries and organizational contexts. These frameworks are valuable resources for a wide range of users, including business professionals, educators, and consultants.
Each framework is presented with visually engaging diagrams and templates, ensuring the content is both informative and appealing. While this compilation is thorough, please note that the slides are intended as supplementary resources and may not be sufficient for standalone instructional purposes.
This compilation is ideal for anyone looking to enhance their understanding of innovation management and drive meaningful change within their organization. Whether you aim to improve product development processes, enhance customer experiences, or drive digital transformation, these frameworks offer valuable insights and tools to help you achieve your goals.
INCLUDED FRAMEWORKS/MODELS:
1. Stanford’s Design Thinking
2. IDEO’s Human-Centered Design
3. Strategyzer’s Business Model Innovation
4. Lean Startup Methodology
5. Agile Innovation Framework
6. Doblin’s Ten Types of Innovation
7. McKinsey’s Three Horizons of Growth
8. Customer Journey Map
9. Christensen’s Disruptive Innovation Theory
10. Blue Ocean Strategy
11. Strategyn’s Jobs-To-Be-Done (JTBD) Framework with Job Map
12. Design Sprint Framework
13. The Double Diamond
14. Lean Six Sigma DMAIC
15. TRIZ Problem-Solving Framework
16. Edward de Bono’s Six Thinking Hats
17. Stage-Gate Model
18. Toyota’s Six Steps of Kaizen
19. Microsoft’s Digital Transformation Framework
20. Design for Six Sigma (DFSS)
To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentationsThe Most Inspiring Entrepreneurs to Follow in 2024.pdf
In a world where the potential of youth innovation remains vastly untouched, there emerges a guiding light in the form of Norm Goldstein, the Founder and CEO of EduNetwork Partners. His dedication to this cause has earned him recognition as a Congressional Leadership Award recipient.
Recently uploaded (20)
Best Competitive Marble Pricing in Dubai - ☎ 9928909666
Best Competitive Marble Pricing in Dubai - ☎ 9928909666
4 Benefits of Partnering with an OnlyFans Agency for Content Creators.pdf
4 Benefits of Partnering with an OnlyFans Agency for Content Creators.pdf
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
Anny Serafina Love - Letter of Recommendation by Kellen Harkins, MS.
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
Income Tax exemption for Start up : Section 80 IAC
Income Tax exemption for Start up : Section 80 IAC
Satta Matka Dpboss Matka Guessing Kalyan Chart Indian Matka Kalyan panel Chart
Satta Matka Dpboss Matka Guessing Kalyan Chart Indian Matka Kalyan panel Chart
The Genesis of BriansClub.cm Famous Dark WEb Platform
The Genesis of BriansClub.cm Famous Dark WEb Platform
Negotiation & Presentation Skills regarding steps in business communication, ...
Negotiation & Presentation Skills regarding steps in business communication, ...
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
Innovation Management Frameworks: Your Guide to Creativity & Innovation
Innovation Management Frameworks: Your Guide to Creativity & Innovation
The Most Inspiring Entrepreneurs to Follow in 2024.pdf
The Most Inspiring Entrepreneurs to Follow in 2024.pdf
4. How to reduce Ground Bounce Reduction on PCBAs.pdf
- 1. How to reduce Ground Bounce Reduction on PCBAs 1. Minimize return paths The shorter the return paths, the lower the inductance between components and the ground plane. Therefore, digital components should be placed directly over digital ground areas and mixed-signal devices should be positioned above bridges between digital and analog ground areas, whenever possible. 2. Use short component leads Using packages with shorter component leads reduces the series inductance. This is also accomplished by using BGAs and vias. Decoupling capacitors should also be used to funnel disturbances to ground as quickly as possible. It is probably a good idea to use these for all IC and transistor ground pins. 3. Use multiple vias Another way to quickly dissipate disturbances or noise from your circuits is to use multiple vias to route to ground. 4. Offset switching, if possible The parasitics that cause ground bounce may not be able to be completely eliminated; however, by offsetting switching times, you can minimize the extent or magnitude of the ground bounce. 5. Use slower switching components, if possible This technique should be used in conjunction with offsets to allow damping to occur prior to the next switching event. This will prevent it from being added to the noise that may be already present.