1.4.1 Generation Sinusoidal
•
0 likes•173 views
This document provides information about generating sinusoidal waveforms and directs the reader to additional resources 7, 8, and 9 for more details.
Report
Share
Report
Share
Recommended
Generation of A.C. voltage
1) The document discusses the generation of alternating current using a single-turn alternator with a rotating coil within a magnetic field.
2) As the coil rotates, an alternating voltage is induced based on Faraday's law of electromagnetic induction. The magnitude of the induced voltage depends on the angle of rotation and reaches its maximum when the coil is perpendicular to the magnetic field lines.
3) The instantaneous induced voltage can be expressed as a sinusoidal function of the angle of rotation, with the maximum voltage achieved at 90° of rotation. This generates an alternating current through a load that also follows a sinusoidal pattern.
7.4.6 slip
This document describes how to calculate the rotor frequency of a two-pole, 50 Hz induction motor given the rotor speed of 2850 rpm. It shows that the slip speed is 3000 rpm, the slip percentage is 5%, and using the formula fs x %slip / 100, the rotor frequency is calculated to be 2.5 Hz.
4.2.1 Better Load
The document describes the circuits and loads for an electrical installation. It lists 19 circuits with various lighting, power outlet, motor, and appliance loads. It calculates the demand current in amps for each phase based on adding the full load or percentage of full load for each circuit based on rating and number of devices. The highest calculated demand is 153.25 amps on phase L2. With a 10% allowance for future additions, the total recommended maximum current is 168.575 amps.
4.1.13 Light Demand 3
This short document does not provide any substantive information to summarize in 3 sentences or less. It only notes that an explanation is not contained in a workbook, but provides no other context or details.
4.1.12 Light Demand 2 Table Part2
The document outlines the demand calculations for 19 different circuit load groups across 3 phases. It lists the load description, current allowance calculation method, and resulting demand current for each phase. The total demand current per phase is calculated at the bottom, with values of 143.8 amps for phase 1, 153.25 amps for phase 2, and 145.05 amps for phase 3.
4.1.11 Light Demand 2 Table
The document contains a table that calculates the current demand per phase for various circuit load groups in an electrical system. It lists 19 load groups categorized by letters A through D, describing each load. It shows the current allowance calculation method and resulting demand in amps for each phase. The total demand current calculated per phase is 143.8 amps for L1, 153.25 amps for L2, and 145.05 amps for L3.
4.1.10 Light Demand 2
This 3 sentence document provides instructions to refer to a specific table on a specific page of a particular standard for additional explanatory information not contained in the current workbook. The instructions direct the reader to Table C2 on page 359 of AS/NZA 3000:2007 for an explanation that is not included in the current document.
4.1.9 Light Demand 1
The document describes the functions of 19 electrical circuits in a building. It lists the types of equipment connected to each circuit such as fluorescent lighting, outlets, motors, and appliances. It also indicates which of the 3 electrical phases (L1, L2, L3) each circuit is connected to.
Recommended
Generation of A.C. voltage
1) The document discusses the generation of alternating current using a single-turn alternator with a rotating coil within a magnetic field.
2) As the coil rotates, an alternating voltage is induced based on Faraday's law of electromagnetic induction. The magnitude of the induced voltage depends on the angle of rotation and reaches its maximum when the coil is perpendicular to the magnetic field lines.
3) The instantaneous induced voltage can be expressed as a sinusoidal function of the angle of rotation, with the maximum voltage achieved at 90° of rotation. This generates an alternating current through a load that also follows a sinusoidal pattern.
7.4.6 slip
This document describes how to calculate the rotor frequency of a two-pole, 50 Hz induction motor given the rotor speed of 2850 rpm. It shows that the slip speed is 3000 rpm, the slip percentage is 5%, and using the formula fs x %slip / 100, the rotor frequency is calculated to be 2.5 Hz.
4.2.1 Better Load
The document describes the circuits and loads for an electrical installation. It lists 19 circuits with various lighting, power outlet, motor, and appliance loads. It calculates the demand current in amps for each phase based on adding the full load or percentage of full load for each circuit based on rating and number of devices. The highest calculated demand is 153.25 amps on phase L2. With a 10% allowance for future additions, the total recommended maximum current is 168.575 amps.
4.1.13 Light Demand 3
This short document does not provide any substantive information to summarize in 3 sentences or less. It only notes that an explanation is not contained in a workbook, but provides no other context or details.
4.1.12 Light Demand 2 Table Part2
The document outlines the demand calculations for 19 different circuit load groups across 3 phases. It lists the load description, current allowance calculation method, and resulting demand current for each phase. The total demand current per phase is calculated at the bottom, with values of 143.8 amps for phase 1, 153.25 amps for phase 2, and 145.05 amps for phase 3.
4.1.11 Light Demand 2 Table
The document contains a table that calculates the current demand per phase for various circuit load groups in an electrical system. It lists 19 load groups categorized by letters A through D, describing each load. It shows the current allowance calculation method and resulting demand in amps for each phase. The total demand current calculated per phase is 143.8 amps for L1, 153.25 amps for L2, and 145.05 amps for L3.
4.1.10 Light Demand 2
This 3 sentence document provides instructions to refer to a specific table on a specific page of a particular standard for additional explanatory information not contained in the current workbook. The instructions direct the reader to Table C2 on page 359 of AS/NZA 3000:2007 for an explanation that is not included in the current document.
4.1.9 Light Demand 1
The document describes the functions of 19 electrical circuits in a building. It lists the types of equipment connected to each circuit such as fluorescent lighting, outlets, motors, and appliances. It also indicates which of the 3 electrical phases (L1, L2, L3) each circuit is connected to.
4.1.7 Example Domestic 3
The document calculates the electrical load of communal services in an apartment building. It shows that 24 lighting points will draw 240 watts and 6 10A sockets will draw up to 12A, for a total demand of 18A per phase. The total demand current per phase for communal services is 18A.
4.1.6 Example Domestic 2
The document calculates the electrical load and demand for 6 living units per phase. It lists the types of loads in each unit, the quantity and allowance per unit, and uses this to calculate the total demand current for phases L1, L2 and L3, which is 154.4 amps for each phase. The key loads included are lighting, power outlets, cooking ranges, air conditioners and hot water systems.
4.1.5 Example Domestic 1
This document discusses the number of living units per phase of a project. It calculates that for 18 total living units divided into 3 phases, there would be 6 living units per phase.
4.1.4 Step 2
This document summarizes the electrical load calculations for 11 circuits in a home. It lists the load type and description for each circuit, the current allowance per unit, and calculates the demand in amps for circuits 1-10. The largest demands are 17.7 amps for an air conditioner and 15 amps for an off-peak hot water system. The total calculated demand current for each phase is 40.7, 39.5, and 46.5 amps respectively.
4.1.3 Example Solution Three
The document calculates the electrical load and demand current for 11 circuits in a home. It groups the loads into categories like lighting, outlets, appliances, and assigns each a description, allowance, and demand calculation. The total demand current per phase is summarized at the bottom, with the highest draw of 46.5 amps on phase L3.
4.1.2 Example Three
The document outlines the functions and ratings of 12 electrical circuits. Circuit 1 provides power for 13 indoor lighting points. Circuit 10 powers an air conditioner rated at 23.6 amps per phase and can draw power from circuits L1, L2, and L3. Circuits 11a and 11b each power a controlled load hot water unit rated at 3.6 kW.
4.1.1 Example Single
This document calculates the total demand current for an electrical installation consisting of:
- 21 lighting points and 12 double sockets, contributing 5A and 15A respectively
- 15 single sockets contributing 10A
- A 6kW oven contributing 0.5A
- A 2.4kW water heater contributing 0.33A
The total demand current calculated is 45.83A.
5.4.4 LR Circuits
The document discusses the time constant and final current value for an RL circuit. It states that:
1) The time constant for the circuit is 0.17 seconds based on the given inductance and resistance values.
2) It will take approximately 0.85 seconds (5 time constants) for the current to reach its final value.
3) Using Ohm's law, the approximate final current after 0.85 seconds is 2 amps.
14.5.4 Example 1 Part 1
This document calculates the apparent power, power factor, and phase angle for a circuit. It finds that the apparent power is 2.308 kVA by multiplying the current of 9.615 by the voltage of 240. This apparent power is larger than the actual power of 1.5 kW, indicating a poor power factor of 0.65 or a 49.46 degree phase angle between the current and voltage.
14.1.2 TRA Power
Reactive power (Q) and true power (P) combine to form apparent power (S). Apparent power is the combination of true power, which is the usable energy in a circuit, and reactive power, which is stored energy that results from the combination of voltage and current out of phase.
14.5.8 Example 1 Part 5
This document calculates the true power, apparent power, and total current for a circuit. It determines that the true power is 1.5 kW, the apparent power is 1.5009 kVA, and the power factor is 0.99994. It then calculates that with an apparent power of 1.5009 kVA at 240 Volts, the total current would be 6.25 amps.
14.5.7 Example 1 Part 4
This document calculates the capacitive reactance (Xc), current (Ic), and reactive power (Qc) of a capacitor with a capacitance of 80 microfarads operating at 60 Hz with a voltage of 240 V. It then calculates the difference between the inductive and capacitive reactive power as 17 VAR.
14.5.6 Example 1 Part 3
This document calculates the capacitive reactance and capacitance value needed for a reactive power of 1.754 kVAR at 240V. It shows that the capacitive reactance is 32.845 ohms and the required capacitance is 80.761 microfarads.
14.5.5 Example 1 Part 2
The document calculates the reactive power (Q) in kilovolt-amperes reactive (kVAR) from measurements of apparent power (S), true power (P), and the formula that reactive power is equal to the square root of the difference between the square of apparent power and the square of true power. It finds that with an apparent power of 2.308 kVA and a true power of 1.5 kW, the reactive power is 1.754 kVAR.
14.5.2 Correction
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
14.5.1 Improvement
Power factor is a measurement of how efficiently electrical power is being used in a circuit. An ideal power factor of one means the current and voltage are in phase, resulting in maximum real power transfer and minimum reactive power. Maintaining a power factor as close to one as possible is important for both utility companies and customers to reduce costs and improve efficiency of electrical power distribution and usage.
14.4.4 Three Watt
This 3 line document contains a formula for calculating the total power (Ptotal) as the sum of three weights (W1, W2, W3). The formula Ptotal = W1 + W2 + W3 is repeated on the second line for emphasis.
June Patch Tuesday
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.More Related Content
More from Talia Carbis
4.1.7 Example Domestic 3
The document calculates the electrical load of communal services in an apartment building. It shows that 24 lighting points will draw 240 watts and 6 10A sockets will draw up to 12A, for a total demand of 18A per phase. The total demand current per phase for communal services is 18A.
4.1.6 Example Domestic 2
The document calculates the electrical load and demand for 6 living units per phase. It lists the types of loads in each unit, the quantity and allowance per unit, and uses this to calculate the total demand current for phases L1, L2 and L3, which is 154.4 amps for each phase. The key loads included are lighting, power outlets, cooking ranges, air conditioners and hot water systems.
4.1.5 Example Domestic 1
This document discusses the number of living units per phase of a project. It calculates that for 18 total living units divided into 3 phases, there would be 6 living units per phase.
4.1.4 Step 2
This document summarizes the electrical load calculations for 11 circuits in a home. It lists the load type and description for each circuit, the current allowance per unit, and calculates the demand in amps for circuits 1-10. The largest demands are 17.7 amps for an air conditioner and 15 amps for an off-peak hot water system. The total calculated demand current for each phase is 40.7, 39.5, and 46.5 amps respectively.
4.1.3 Example Solution Three
The document calculates the electrical load and demand current for 11 circuits in a home. It groups the loads into categories like lighting, outlets, appliances, and assigns each a description, allowance, and demand calculation. The total demand current per phase is summarized at the bottom, with the highest draw of 46.5 amps on phase L3.
4.1.2 Example Three
The document outlines the functions and ratings of 12 electrical circuits. Circuit 1 provides power for 13 indoor lighting points. Circuit 10 powers an air conditioner rated at 23.6 amps per phase and can draw power from circuits L1, L2, and L3. Circuits 11a and 11b each power a controlled load hot water unit rated at 3.6 kW.
4.1.1 Example Single
This document calculates the total demand current for an electrical installation consisting of:
- 21 lighting points and 12 double sockets, contributing 5A and 15A respectively
- 15 single sockets contributing 10A
- A 6kW oven contributing 0.5A
- A 2.4kW water heater contributing 0.33A
The total demand current calculated is 45.83A.
5.4.4 LR Circuits
The document discusses the time constant and final current value for an RL circuit. It states that:
1) The time constant for the circuit is 0.17 seconds based on the given inductance and resistance values.
2) It will take approximately 0.85 seconds (5 time constants) for the current to reach its final value.
3) Using Ohm's law, the approximate final current after 0.85 seconds is 2 amps.
14.5.4 Example 1 Part 1
This document calculates the apparent power, power factor, and phase angle for a circuit. It finds that the apparent power is 2.308 kVA by multiplying the current of 9.615 by the voltage of 240. This apparent power is larger than the actual power of 1.5 kW, indicating a poor power factor of 0.65 or a 49.46 degree phase angle between the current and voltage.
14.1.2 TRA Power
Reactive power (Q) and true power (P) combine to form apparent power (S). Apparent power is the combination of true power, which is the usable energy in a circuit, and reactive power, which is stored energy that results from the combination of voltage and current out of phase.
14.5.8 Example 1 Part 5
This document calculates the true power, apparent power, and total current for a circuit. It determines that the true power is 1.5 kW, the apparent power is 1.5009 kVA, and the power factor is 0.99994. It then calculates that with an apparent power of 1.5009 kVA at 240 Volts, the total current would be 6.25 amps.
14.5.7 Example 1 Part 4
This document calculates the capacitive reactance (Xc), current (Ic), and reactive power (Qc) of a capacitor with a capacitance of 80 microfarads operating at 60 Hz with a voltage of 240 V. It then calculates the difference between the inductive and capacitive reactive power as 17 VAR.
14.5.6 Example 1 Part 3
This document calculates the capacitive reactance and capacitance value needed for a reactive power of 1.754 kVAR at 240V. It shows that the capacitive reactance is 32.845 ohms and the required capacitance is 80.761 microfarads.
14.5.5 Example 1 Part 2
The document calculates the reactive power (Q) in kilovolt-amperes reactive (kVAR) from measurements of apparent power (S), true power (P), and the formula that reactive power is equal to the square root of the difference between the square of apparent power and the square of true power. It finds that with an apparent power of 2.308 kVA and a true power of 1.5 kW, the reactive power is 1.754 kVAR.
14.5.2 Correction
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
14.5.1 Improvement
Power factor is a measurement of how efficiently electrical power is being used in a circuit. An ideal power factor of one means the current and voltage are in phase, resulting in maximum real power transfer and minimum reactive power. Maintaining a power factor as close to one as possible is important for both utility companies and customers to reduce costs and improve efficiency of electrical power distribution and usage.
14.4.4 Three Watt
This 3 line document contains a formula for calculating the total power (Ptotal) as the sum of three weights (W1, W2, W3). The formula Ptotal = W1 + W2 + W3 is repeated on the second line for emphasis.
More from Talia Carbis (20)
Recently uploaded
June Patch Tuesday
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.Best 20 SEO Techniques To Improve Website Visibility In SERP
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
GraphRAG for Life Science to increase LLM accuracy
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
Infrastructure Challenges in Scaling RAG with Custom AI models
Building Retrieval-Augmented Generation (RAG) systems with open-source and custom AI models is a complex task. This talk explores the challenges in productionizing RAG systems, including retrieval performance, response synthesis, and evaluation. We’ll discuss how to leverage open-source models like text embeddings, language models, and custom fine-tuned models to enhance RAG performance. Additionally, we’ll cover how BentoML can help orchestrate and scale these AI components efficiently, ensuring seamless deployment and management of RAG systems in the cloud.
Mind map of terminologies used in context of Generative AI
Mind map of common terms used in context of Generative AI.
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
OpenID AuthZEN Interop Read Out - Authorization
During Identiverse 2024 and EIC 2024, members of the OpenID AuthZEN WG got together and demoed their authorization endpoints conforming to the AuthZEN API
20240605 QFM017 Machine Intelligence Reading List May 2024
Everything I found interesting about machines behaving intelligently during May 2024
UiPath Test Automation using UiPath Test Suite series, part 6
Welcome to UiPath Test Automation using UiPath Test Suite series part 6. In this session, we will cover Test Automation with generative AI and Open AI.
UiPath Test Automation with generative AI and Open AI webinar offers an in-depth exploration of leveraging cutting-edge technologies for test automation within the UiPath platform. Attendees will delve into the integration of generative AI, a test automation solution, with Open AI advanced natural language processing capabilities.
Throughout the session, participants will discover how this synergy empowers testers to automate repetitive tasks, enhance testing accuracy, and expedite the software testing life cycle. Topics covered include the seamless integration process, practical use cases, and the benefits of harnessing AI-driven automation for UiPath testing initiatives. By attending this webinar, testers, and automation professionals can gain valuable insights into harnessing the power of AI to optimize their test automation workflows within the UiPath ecosystem, ultimately driving efficiency and quality in software development processes.
What will you get from this session?
1. Insights into integrating generative AI.
2. Understanding how this integration enhances test automation within the UiPath platform
3. Practical demonstrations
4. Exploration of real-world use cases illustrating the benefits of AI-driven test automation for UiPath
Topics covered:
What is generative AI
Test Automation with generative AI and Open AI.
UiPath integration with generative AI
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Fueling AI with Great Data with Airbyte Webinar
This talk will focus on how to collect data from a variety of sources, leveraging this data for RAG and other GenAI use cases, and finally charting your course to productionalization.
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
ここ3000字までしか入らないけどタイトルの方がたくさん文字入ると思います。
HCL Notes and Domino License Cost Reduction in the World of DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
Taking AI to the Next Level in Manufacturing.pdf
Read Taking AI to the Next Level in Manufacturing to gain insights on AI adoption in the manufacturing industry, such as:
1. How quickly AI is being implemented in manufacturing.
2. Which barriers stand in the way of AI adoption.
3. How data quality and governance form the backbone of AI.
4. Organizational processes and structures that may inhibit effective AI adoption.
6. Ideas and approaches to help build your organization's AI strategy.
Removing Uninteresting Bytes in Software Fuzzing
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
Artificial Intelligence for XMLDevelopment
In the rapidly evolving landscape of technologies, XML continues to play a vital role in structuring, storing, and transporting data across diverse systems. The recent advancements in artificial intelligence (AI) present new methodologies for enhancing XML development workflows, introducing efficiency, automation, and intelligent capabilities. This presentation will outline the scope and perspective of utilizing AI in XML development. The potential benefits and the possible pitfalls will be highlighted, providing a balanced view of the subject.
We will explore the capabilities of AI in understanding XML markup languages and autonomously creating structured XML content. Additionally, we will examine the capacity of AI to enrich plain text with appropriate XML markup. Practical examples and methodological guidelines will be provided to elucidate how AI can be effectively prompted to interpret and generate accurate XML markup.
Further emphasis will be placed on the role of AI in developing XSLT, or schemas such as XSD and Schematron. We will address the techniques and strategies adopted to create prompts for generating code, explaining code, or refactoring the code, and the results achieved.
The discussion will extend to how AI can be used to transform XML content. In particular, the focus will be on the use of AI XPath extension functions in XSLT, Schematron, Schematron Quick Fixes, or for XML content refactoring.
The presentation aims to deliver a comprehensive overview of AI usage in XML development, providing attendees with the necessary knowledge to make informed decisions. Whether you’re at the early stages of adopting AI or considering integrating it in advanced XML development, this presentation will cover all levels of expertise.
By highlighting the potential advantages and challenges of integrating AI with XML development tools and languages, the presentation seeks to inspire thoughtful conversation around the future of XML development. We’ll not only delve into the technical aspects of AI-powered XML development but also discuss practical implications and possible future directions.
AI-Powered Food Delivery Transforming App Development in Saudi Arabia.pdf
In this blog post, we'll delve into the intersection of AI and app development in Saudi Arabia, focusing on the food delivery sector. We'll explore how AI is revolutionizing the way Saudi consumers order food, how restaurants manage their operations, and how delivery partners navigate the bustling streets of cities like Riyadh, Jeddah, and Dammam. Through real-world case studies, we'll showcase how leading Saudi food delivery apps are leveraging AI to redefine convenience, personalization, and efficiency.
Recently uploaded (20)
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
Best 20 SEO Techniques To Improve Website Visibility In SERP
Best 20 SEO Techniques To Improve Website Visibility In SERP
GraphRAG for Life Science to increase LLM accuracy
GraphRAG for Life Science to increase LLM accuracy
Infrastructure Challenges in Scaling RAG with Custom AI models
Infrastructure Challenges in Scaling RAG with Custom AI models
Mind map of terminologies used in context of Generative AI
Mind map of terminologies used in context of Generative AI
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
20240605 QFM017 Machine Intelligence Reading List May 2024
20240605 QFM017 Machine Intelligence Reading List May 2024
UiPath Test Automation using UiPath Test Suite series, part 6
UiPath Test Automation using UiPath Test Suite series, part 6
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
みなさんこんにちはこれ何文字まで入るの？40文字以下不可とか本当に意味わからないけどこれ限界文字数書いてないからマジでやばい文字数いけるんじゃないの？えこ...
HCL Notes and Domino License Cost Reduction in the World of DLAU
HCL Notes and Domino License Cost Reduction in the World of DLAU
AI-Powered Food Delivery Transforming App Development in Saudi Arabia.pdf
AI-Powered Food Delivery Transforming App Development in Saudi Arabia.pdf
1.4.1 Generation Sinusoidal
- 2. For more information about Generation of Sinusoidal Waveform click on resource 7 under resources
- 7. For more information about Generation of Sinusoidal Waveform click on resource 8 & 9 under resources