Seminar on Nano Ic Engine.(If any need that ppt send email id on comment)

1. SEMINAR ON
NANO IC
ENGINE
BY RUDRASH

2. CONTENTS
1) INTRODUCTION
2) REVOLUTIONS IN ENGINES
3) IDEA OF SIZE OF NANO
4) MAIN COMPONENTS
5) CONSTRUCTION OF "NANO" - A 0.1CC ENGINE
6) EXPOLDED VIEW
7) NANO SPANNER
8) CUTTER

3. 9) PISTON CROWN AND VENTURI
10) CRANKSHAFT COMPONENT
11) WORKING
12) APPLICATION
13) ADVANTAGES
14) CONCLUSION
15) REFERENCES

4.  NANO… one billionth of one and one third of micro ,to be
precise 10^-9 m.
 Nanotechnology is the manipulation of matter on an atomic and
molecular scale.
 It is the technology based upon the scaling down the existing
technologies to next level of precision and miniaturization.
 Nanotechnology in mechanical field is the internal combustion
engine on a Nano scale, which I have chosen as My area of interest.
INTRODUCTION

5. External combustion engine is the heat engine in which fuel
combustion takes place external to cylinder. Due to this it is bulky
and consumes a lot of place.
Second revolutions of heat engines are ICE in which fuel
combustion takes internally and consumes less place and became
compact, cost effective.
Of late third revolution is NANO Internal Combustion Engine.
Revolutions In Engines

6.  From back plate to drive
washer is less than 1 inch.
 There are no exotic
materials required.
It has high precision ,cost
effective, high speed (up to
40000rpm).
IDEA OF SIZE OF NANO

7. MAIN COMPONENTS USED
a) CRANK CASE
b) BACK PLATE
c) CYLINDER AND HEAD
d) VENTURI AND NEEDLE VALVE ASSEMBLY
e) CONRODS AND CRANK SHAFTS
f) PISTON AND CONTRA PISTON

8. Construction of "Nano" - A 0.1cc
Compression Ignition Engine
 The Nano is a 0.1cc compression ignition engine - most
frequently, if somewhat inaccurately, referred to as a "diesel".
 It was designed by Richard Gordon and the plans were included as
a supplement with the British Magazine Model Engineer in the early
1990's.

9. EXPLODED VIEW OF ENGINE

10. Like all model IC projects, there are a few special jigs and tools
required to construct the Nano.
The construction is extremely conventional - only the scale is
unusual.
The constructional cost is just USA$10 only in Indian rupees it is
approx. RS. 500 .

11. NANO SPANNER
 The odd looking thing is a special Nano-Spanner
required to tighten the back plate.
 It also fits the fuel nipple.

12. CUTTER
 The cutter is used to form the exhaust ports in the cylinder

13. PISTON CROWN AND VENTURI
 The crown of the piston is conical to assist transfer. The contra piston has a
matching concave conical depression.

14. CRANKSHAFT COMPONENTS

15.  When it is fired, it run briefly, oscillating back and forth about
TDC like over compressed diesels with small mass fly wheels are
wont to do Running!.
 But spring starters are the only way to start ultra small diesels -
hand propping just won't work.
WORKING OF NANO

16. Also, the fuel for mini diesels needs a lot of ether - as high as
50% by volume.
With high ether fuel and a spring starter, the little Nano will
burst into life.
Richard Gordon claims it will turn 40,000 rpm.
CONTINUED…..

17. APPLICATIONS
 Nano ic engine has various applications ranging from race cars to
space crafts.

18.  In race cars this IC Nano engine was used. The engine was fully
fabricated, that is, no castings were employed.
 It can be controlled in aero planes/satellites/space ships etc., The
timing of inlet and exhaust valves.
 According to NASA reports they are experimenting about the use
of Nano engine in Nano & Pico satellites.

19.  In case of a mine tragedy where harmful gases are emitted ,these
Nano ic engines can be employed as powerful blowers to blow
out these gases is a time saving & the lives of trapped miners .
 Agriculture pumps sets.
 Every field of industry.

20. ADVANTAGES
Adds great power to your engine.
Boosts miles per gallon.
Prolongs engine life.
Cleans combustion chamber.
Protects the environment.

21. With the application of Nano in every sphere of life the ‘big’ may
not find its place in engineering dictionary in future.
If we are to continue these trends we will have to develop a new
manufacturing technology.
It will let us inexpensively build Nano system with mole quantities
that are molecular in both size and precision.
NANO TECHNOLOGY WILL DO THIS……..
CONCLUSION

22. REFERENCES
 K. Eric Drexler,” Engine Of Creation(The Coming Era Of Nano
technology)”In1986 Pg.12-15
 Gunvant S. Bhangale1, Shubham S. Abhang,Vaibhav D. Bhoj
,”NANO IC ENGINE”, 2nd International conference on recent trends
in engineering sci. and managent (International centre, YMCA
,New Delhi), Date:-20/02/2016
 Prof.Alka Mata, ”NANO IC ENGINE”, International Journal of
Scientific and Research Publications, Volume 4, Issue 8, August
2014 (ISSN 2250-3153)
 Rizwan Shaikh, Tarique Khan “NANO IC ENGINE” (International
Journal Of Engineering, Education And Technology (ARDIJEET)
ISSN 2320-883X, VOLUME 3, ISSUE 2, 01/04/2015)

23. ANY QUERIES?