Eee hardware list

HYDERABAD | VIJAYAWADA | GUNTUR
Accords IEEE & International Standards Mobile: 9603150547
Vision Solutions
4/13 Brodipet, Guntur | Benz Circle, Vijayawada | Pragathi Nagar Hyderabad
E-Mail:visionsolutions.9@gmail.com, call-9603150547
Web site: www.visionsolutions.tech
VisionGroups
Project
code
Title of the Project Description
IJEE01
Distribution Transformer Monitoring
Using GSM Technology.
In this we will monitor transformer parameters like current,
voltage and temperature, if any of these parameters found
abnormal then this systems sends SMS alert to user.
IJEE02
Prepaid Energy Meter with GSM
technology
the GSM technology is used so that the consumer would receive
messages about the consumption of power (in watts) and if it
reaches the minimum amount, it would automatically alert the
consumer to recharge
IJEE03
Bluetooth remote home automation
system using android application.
With this we can control home appliances from our android
phone. This safe and secure.
IJEE04
Substation monitoring and controlling
using GSM
Substation parameters are monitored and it also send alert
message when these parameters are abnormal
IJEE05
Low cost wireless sensor network in field
operation monitoring of ac motor
The main aim of this project is to monitor the operation
conditions of single-phase AC motors
IJEE06
Applied research of the intelligent
temperature-controlled speed adjustable
motor in radiator fan
In this project the speed of the FAN will be controlled
automatically based on current temperature.
IJEE07
Electronic energy meter with instant
billing
This paper presents automated billing of energy meter. It is just
like postpaid mobile connection. This is useful for billing purpose
in electricity board authority.
IJEE08
Remote power on/off control and current
measurement for home electric outlets
based on a low-power embedded board
and ZIGBEE
We can control the home appliances through ZigBee remote and
this system will display the power consumed by the loads.
IJEE09
Energy saving project for heating system
with ZigBee wireless control network
The main of this project is to develop energy saving heating
system using ZigBee wireless technology
IJEE10
Implementation of ZIGBEE-GSM based
home security monitoring and remote
control system
The main aim of this project is to develop a security and control
automation system by which we can control and monitor the
status of home appliances
IJEE11
Automation of residential electricity cut
off using network based embedded
controller
The main aim of this project is to develop the automation system
for residential electricity cut off using network based embedded
controller
IJEE12
Design of intelligent streetlight
monitoring system based on micro
The main aim of this project is to design an intelligent streetlight
monitoring system for power saving

Vision Solutions
VisionGroups
controller
IJEE13
GSM-based wireless home appliances
monitoring & control system
The main aim of this project is to develop a system, which uses
Mobile technology that keeps monitoring of the various
appliances, and will control the operation of these appliances with
respect to the signal sent by the mobile
IJEE14
Real-Time Atomization Of Agricultural
Environment for Social Modernization of
Indian Agricultural System
The main of this project is to control the agriculture motor using
mobile and also to protect the motor
IJEE15
Method of Measuring Power Quality and
Development of Monitor Device
The transmission line voltage, current, and power factor, active
power and reactive power are measured and displayed on the
LCD
IJEE16
A novel technique of ac power control
using micro controller based inverter
The main aim of this work is to design a simple low cost AC
voltage controller used to Control AC loads which doesn't
demand very high precisions
PE01
Design of controlled DC voltage
regulator using semi converter.
230v ac is converted in to dc using SCR's and the required firing
pulses for the SCR's are given by the microcontroller. Only 2
SCR's and 2 diodes will be there in the converting circuit.
PE02
Design of controlled DC voltage
regulator using full wave converter
230v ac is converted in to dc using SCR's and the required firing
pulses for the 4 SCR's are given by the microcontroller.
PE03
Industrial battery charger by thysitor
firing angle control
230v ac is converted in to dc using SCR's. This dc is used to
charge the batteries. The required firing pulses for the SCR's are
given by the microcontroller. 4 SCR's will be there in converting
circuit.
PE04 Dual converter using thyristors
Single phase dual converter consists of a pair of thyristor
controlled bridge (4 SCRs X 2). The output of this bridge is given
to a DC motor which can be made to run in either direction with
different speed levels by changing the firing angle.
PE05
Single phase H-bridge inverter with
PWM technology using microcontroller
In this dc is voltage is converted into A.C by MOSFET bridge.
Here PWM signals are generated by controller and are given to
MOSFET bridge and variable output voltages are generated
which can be observed by seeing brightness of the bulb.
PE06
Single phase sine wave PWM H-bridge
inverter using micro controller
In this dc is voltage is converted into A.C by MOSFET bridge.
Here sine wave PWM signals are generated by controller and are
given to MOSFET bridge.
PE07
SPWM space vector pulse width
modulation

Vision Solutions
VisionGroups
PE08
Step down cyclo converter using dual
converter SCR bridge
A cyclo converter converts an alternating current (AC) waveform
to another AC waveform of a different frequency; In this project
we are using 8 SCRs. This variable frequency is given to the bulb
where the flickering can be observed.
PE09 speed control of dc motor by using 8051
The controller will take the data from the key pad and it will
generate the PWM required for the motor to rotate at desired
speed. The pulses are then given to the l293d which drives DC
motor.
PE10
speed control of dc motor using four
quadrant chopper
In this speed of the motor is controlled by four quadrant operation
of chopper .It consists of MOSFET bridge where the pulses are
varied to get the required polarity and output of the output
voltage. This output is given to the DC motor.
PE11
speed control of universal motor using
IGBT
In this input AC is converted to DC and type A chopper is
employed to get a variable DC output voltage. This variable DC
voltage is given to universal motor where the speed of the motor
is varied.
PE12
speed control of induction motor using
voltage control.
Speed of induction motor is proportional to voltage applied.
Therefore input voltage is varied using A.C voltage controller
where firing pulses of thyristors are varied according to desired
speed. In this only 2 SCR's which are in anti parallel are used.
PE13
speed control of induction motor using
frequency control
Speed of induction motor is proportional to input frequency.
Therefore input frequency is varied using cyclo converter where
firing pulses of thyristors are varied according to desired speed.
PE14
Speed control of induction motor using
v/f control
In this both the input frequency & voltage is varied so that the
motor is driven at desired speed. Here micro controller is used for
controlling action where firing pulses of thyristors employed are
varied according to desired output speed.
PE15
H-Bridge and PWM based DC Motor
direction and speed control system
In this speed of the motor is controlled by four quadrant operation
of chopper .It consists of MOSFET bridge where the pulses are
varied to get the required output voltage.
PE16
Transformer less Variable Frequency
Drive
Speed of induction motor is proportional to input frequency.
Therefore input frequency is varied by using cyclo converter
where firing pulses of thyristors are varied according to desired
speed.
PS01
Substation monitoring system
(measurement of PF, voltage, current,
temp.)
Continuous monitoring of substation is essential for reliable&
safer power supply at customer point. In this project are going to
monitor various supply parameters viz., voltage, frequency, p.f,

Vision Solutions
VisionGroups
power ensuring protection against various faults.
PS02
Transmission line multiple fault
indication to substation
Ensuring reliable supply to customers is major point in
distributing power. In this project complete protection against
such faults are monitored & if any fault occurs it indicates to
nearby substation through RF technology
PS03
Automatic power factor correction using
switching capacitors
In this power factor correction unit it consists of a number of
capacitors that are switched by means of relays. These
contactors/relays are controlled by a regulator that measures
power factor in an electrical network. Depending on the load and
power factor of the network, the power factor controller will
switch the necessary blocks of capacitors in steps to make sure
the power factor stays above a selected value.
PS04
static var compensators
In this power factor correction unit consists of a number of
capacitors that are switched by means of relays. These contactors
are controlled by a regulator that measures power factor in an
electrical network. Depending on the load and power factor of the
network, the power factor controller will vary the firing angle of
the thyristor. This will vary the net value of the capacitance
connected to the supply.
PS05
Transformer oil temperature monitoring
with automatic Circuit Breaker operation.
The temperature of the transformer oil is monitored and displayed
on the LCD. When the temperature increases we will switch ON
cooling FAN. Even after switching the FAN if the temperature is
not decreased then we will switch of the transformer by using a
relay. Bulb is connected as a load.
PS06
Design and construction of Earth fault
relay for single phase power system
We will measure the current in the earth conductor by using
current transformer and ADC. When this current is increased to a
value greater than the pre defined value then the load is switched
off showing indication of the earth fault. Buzzer is also activated
by the controller.
PS07 energy tapping identifier
PS08
Unbalanced three phase optimal power
flow for smart grids
Whenever a three phase load is unbalanced it will correct the load
by switching some of the single phase loads to the other phases.
PS09
Automatic change over for three phase
connection with data logger
by switching some of the single phase loads to the other phases
and the status of all the loads is shown on the display.
PS10
Automatic switching of consumer
connection in distribution feeder for
In the distribution feeder if the single phase consumer loads and
unbalancing a three phase system then the consumers are

Vision Solutions
VisionGroups
different load distribution switched to other phases so that the overall three phase system
will remain in balanced condition .
PS11
Single phasing preventer for protection of
three phase (3-ph) loads
All the three phase induction motors need the power supply in all
the three phases when it is running if any of the phases is having
a power outage then the motor is switched off by using relay and
the fault phase is displayed on the LCD so that problem can be
solved easily.
PS12
Microcontroller based Three Phase Load
safety implementation with phase fault
detector
Whenever a three phase fault is occurred it will be indicated by
using OP-AMPS and by measuring voltages and currents. And
the type of fault is indicated in the display.
PS13
An On-line Monitoring System of
Transmission Line Conductor
Whenever there is an internal fault or the earth fault then we can
sense that by measuring the magnitude of the current and this will
give type of the fault.
PS14
Over voltage or under voltage tripping
mechanism
Whenever there is fault in the transmission line the load is
switched off and the type of the fault is displayed on the display.
If the fault if temporary fault then the load is reconnected to the
line if not the load remains disconnected. And the faulty phase is
also displayed on the display.
PS15
Three phase fault analysis with auto reset
on temporary fault and permanent trip
other wise
Whenever there is fault in the transmission line the load is
switched off and the type of the fault is displayed on the display.
If the fault if temporary fault then the load is reconnected to the
line if not the load remains disconnected. And the faulty phase is
also displayed on the display.
PS16
Auto selection of any available phase in 3
phase supply system
When a single phase load is connected to a phase which is having
a power outage then the load is automatically switched to another
phase by using relays so that the availability of the single phase
from the three phases will be more.
SL01
Renewable Energy management – Solar
based lighting system with inverter and
CFL lamp load
Two modes of operation of the solar inverter will be there. They
are low power mode and balanced power mode. In low power
mode only one cfl light is switched on and the backup time will
be more. In balanced power mode two cfl lights are switched on
for getting more brightness. Output supply is taken from the
inverter.
SL02
Solar pv cell tracking system for
obtaining maximum power output
The project aims at designing a system that would sense and
follow the position of the sun and rotate the panel in the direction
of the sun to obtain maximum power output
SL03 Solar based irrigation pumping system The solar energy form the pv panel is first stored in the battery

Vision Solutions
VisionGroups
and then given to the inverter. The ac output from the inverter is
then connected to the 230v operated motor and a pump is
connected to the motor for pumping the water.
SL04
Solar based LED street light system with
time controlled and auto dimming based
on ambient light
This project is design to reduce the power with present street light
system.
SL05 Solar based traffic light control system
Traffic Lights are controlled based on time and power for these
lights is obtained from Solar panel.
SL06
Wireless motor starter with
acknowledgement using solar energy for
agricultural application
This system is used to give information to formers about power
status and we can control the motor without going to the field
with SMS
AS01
Smart Remote for controlling electrical
appliance through android mobile
With this we can control any electrical appliances with our
android phone, no need of another remote .It is safe and secure
also.
AS02
Virtual nurse- controlling wheel chair
through android mobile
With this the patient can easily control his wheel chair through
simple and smart touching of android mobile
AS07
With this the patient can easily control his
wheel chair through simple and smart
touching of android mobile
With this we can control any electrical appliances in home or
office or industry with our android phone, no need of another
remote .It is safe and secure also.
AS09
Smart regulator for controlling fan speed
through Android mobile.
With this we can control speed of fan or AC from our android
mobile.
AS10
AC motor speed controller through
Android mobile
With this we can control speed of AC motor from our android
mobile
AS11
Advanced street light controlling system
through smart phone.
In this we can control street light from anywhere through smart
phone.
AS13
Industry/home/office automation through
smart phone.
With this project we can control any electrical appliances of
office or home or industry from anywhere by using Smart phone
AS14
Industrial parameters monitoring system
through Smartphone
We can monitor different parameters like temperature, voltage,
etc through online using smart phone from anywhere
VP08
Home /office/industry electrical
appliances controlling by phone call and
confirmation through voice feedback.
In this we will switch off and switch on any electrical appliances
just by calling to this system and press some buttons using DTMF
technology. This system also sends voice feedback of device
status that is whether device is on or off.
VP12 Substation monitoring and controlling This system monitor the different parameters of substation like

Vision Solutions
VisionGroups
system with voice alerts. voltage, current and temperature and gives respective voice alerts
when something goes abnormal condition and takes necessary
action.
FS01
Standalone data logger in SD/MMC card
with time stamp for industrial
applications.
In this we will monitor and store different parameters in industry
like temperature, voltage, etc .We will store these parameters
values in SD card along with measured time and date also. The
stored data format will be in .txt file or excel format so that we
can go through entire monthly data using system.
FS05
Advanced embedded system based a
paperless feedback system for colleges
and event management systems
As we know to save our world we have to reduce usage of paper.
This project helps in eliminate papers used in feedback systems.
In this the feedback and suggestions should be entered from key
board and this data will be stored in memory card in a file format
using ARM7 micro controller.
ET01
Industry parameters monitoring and
controlling system based on embedded
web server.
In this we will monitor industry parameters like current, voltage,
temperature, etc through online using internet from anywhere in
the world and we can also control electrical appliances from
internet.
ET03
Zigbee and internet based advanced street
light controlling system.
With the help of internet and Zigbee technology we can reduce
man power in street light controlling process. We can control
street lights from online itself.
ET05 Internet based home/office automation.
With this system we can control any electrical appliances of
home or office from anywhere in the world using internet.
EE01
Wireless Scrutinizer for Detecting the
fault in Power System.
We take a 230v supply voltage and measure the current in it.
Fault condition is created by using bulbs. We measure the input
and output current of the load using 2 ct's. When the bulb is on
we assume fault is created and it is indicated in another section
using rf.
EE02
Wireless load measuring meter for power
line.
The power in the transmission line is calculated by measuring
voltage, current, power factor, and this is indicated in the display
by sending the data wirelessly.
EE03
Up-to-date Recording System of Power
Line Losses.
The power loss in the transmission line is calculated by
measuring the voltage drop in the line. The voltage drop is
created by using a resistor and an inductor.
EE04
Underground broken conductor & power
theft identification.
The power theft can be measured by measuring the difference in
the current readings of the two ct's that are connected at both the
ends of the transmission line.

Vision Solutions
VisionGroups
EE05
Two quadrant chopper drive for DC
motor speed control.
This can be done for small dc motor as well for big (around half
hp) motors also depends upon motor availability.
EE06
Wireless motor starter with
acknowledgement using solar energy for
agricultural application
This system sends a message to user when power comes an also
sends information whenever power is absent. This system works
with solar energy
EE07
Four quadrant chopper drive for DC
motor speed control
This can be done for small dc motor as well for big (around half
hp) motors also depends upon motor availability
EE08
design of closed loop controlled DC
voltage regulator using full wave
converter
the 230v ac is converted in to dc using SCRs and the output
voltage is measured by the ADC and the firing angle of the SCRs
is controlled by the microcontroller only 2 SCRs and 2 diodes
will be there is converting circuit
EE09
switching capacitors.
The power factor is measured by using zero crossing detectors
and it is corrected by connecting the capacitors using TRIACs or
relays.
EE10
static VAR compensators.
and it is corrected by connecting a single capacitor of larger value
using TRIAC and by controlling the firing angle.
EE11
Design of closed loop controlled DC
voltage regulator using full wave semi-
converter.
The 230v ac is converted in to dc using SCRs and the output
is controlled by the microcontroller only 4 SCRs will be there in
converting circuit.
EE12
Three phase load protector with
automatic fault indication using micro
processor.
Whenever a three phase fault is occurred it will be indicated by
using OP-AMPS and by measuring voltages and currents. And
the type of fault is indicated in the display.
EE13 Thyristor based soft starter.
The advantage of these starters is the starting current can be
controlled to a much lower values than that of the value achieved
with the traditional starters.
EE14 Thyristor based star/delta starter.
6 bulbs are used to represent the motor. There are connected to
form into 3 pairs with 2 each connected in series. They are
connected in star first then in delta to the three phase supply.
EE15
Unbalanced Three-phase Optimal Power
Flow for Smart Grids.
EE16
Maximum Demand Controller for
Industries.
This system automatically switches off the low priority
appliances whenever maximum loam power reached.
EE17 Automatic Switching of consumer Whenever a three phase load is unbalanced it will correct the load

Vision Solutions
VisionGroups
connection in distribution feeder for
efficient load distribution
EE18
Distribution grid transformers monitoring
using GSM with forced cooling control
system
The data at the distribution transformer is observed using GSM
and if there is any fault it will on the cooling fans. If the fault is
on current then it will switch off the transformer
EE19
Remote substation monitoring system
using bidirectional power line
communication.
With the same 230 v power line we can monitor substation
parameters.
EE20
Design of closed loop controlled DC
voltage regulator using full wave
converter through computer.
the 230v ac is converted in to dc using SCR's and the output
is controlled by the microcontroller only 2 SCRs and 2 diodes
will be there is converting circuit. The required output voltage is
set by using hyper terminal.
EE21
Design of closed loop controlled ac
voltage regulator using TRIAC.
Same as the speed control of ac motor but here output voltage is
measured using ADC.
EE22
Transmission line multiple faults
detection and indication to electricity
board.
Voltage and current faults are detected using differential
protection scheme and the type of the fault is transmitted using
RF.
EE23
Power theft identification system in
distribution lines using differential power
measurement.
Current at both the ends of transmission line are measured using
CTs and if there is a difference in those currents it means power
was theft.
EE24
Automatic transformer shunt and series
parameter calculation from open circuit
and short circuit test reading.
The OC and SC test readings of the transformer are given through
keypad and microcontroller will do calculation any give the
output on the LCD.
EE25 Closed loop dc motor speed control.
In this we will control the speed of dc motor and we also take the
feedback from the motor and correct the speed level to desired
level.
EE26
Design of cyclo converter using micro
controller.
The input supply frequency is about 50 Hz. We can get the
multiples of 50hz using the SCRs. controller will generate pulses
for 4 SCRs and the output frequency of the sine wave is
controlled.
EE27 Reverse power protection for generator.
The phase angle of the current and voltage are measured to
measure whether the power is in reverse direction of not if the
power is in reverse direction then it will switch of the supply.
EE28
Automatic transformer protection using
numerical relay.
Difference in currents of the two current transformers' will give a
buzzer sound.

Vision Solutions
VisionGroups
EE29 Automatic phase sequence corrector.
Whenever the RYB phase sequence is changed it will be
corrected by using relays.
EE30 Design of earth fault relay.
Whenever there is an internal fault or the earth fault then we can
sense that by measuring the magnitude of the current and this will
give type of the fault.
EE31
Reactive power compensation using
STACOM.
and it is corrected by connecting a single capacitor of larger value
using TRIAC and by controlling the firing angle.
EE32
Speed control of universal motor using
IGBT.
This will be same as the speed control of the ac motor using
TRIAC but only difference is IGBT is used to vary the voltage
and we will control the dc voltage. First we will convert the 230v
ac into dc and then we will control.
EE33
Efficient power saver for street lights
using LDR, RTC, LEDs light with solar
power
This project saves more power that is being wasted in present
street light switching. In this we will consider time and sunlight
intensity and we use LED lights and solar power
EE34
Agricultural motor controlling with motor
safety and water level indicator using
GSM.
The former can control his field motor without need of going to
his field just by sending message. This system also provides
safety motor from over heat, low phase power and water level
indication.
EE35
Automatic changeover for 3 phases
connections with data logger.
EE36
Solar Tracking system for Maximum
power output with real time power
monitoring system.
In this the panel will give maximum power by changing its
direction according to sun light direction. It can be done with two
motors arrangement or single motor arrangement
EE37
Voice guider and medicine reminder for
patients and old age persons.
In this the user will be given one remote (IR or RF or ZIGBEE),
he has to press any button to get what service he wants and that is
played from voice IC so that any person can hear it and come to
the user. Another feature of this project is to remind the user for
medicines.
EE38
Broken conductor detection for overhead
lines.
The broken conductor can be sensed by using the voltage drop in
the line. We will give three switches to indicate broken condition
when the switch is operated it will indicate which switch is
operated in terms of kilometers.
EE39 Intelligent shopping trolley using RFID
With this we can save billing time and instantaneously the rate
and expiry date of the product will be displayed so that we can do
the shopping within our budget.

Vision Solutions
VisionGroups
EE40
Elegant home with power saving,
security, safety, remote controlling and
auto control of water tank motor
In this we will provide multi features to home like remote
controlling of home appliances ,auto controlling of lights depends
upon sunlight and auto controlling of water tank motor when tank
is full and alert the user when intruders come or when gas leakage
or fire accident occurs
EE41
Intelligent train engine to avoid accidents
and controlling railway gate
automatically.(add alcohol)
In this we will control the train by monitoring the driver's
position or activeness and the gate will b e controlled
automatically when train is near the gate.
EE42
Design And Development Of Prepaid
Energy Meter With Serial Data
Transmission
In this we have one smart card which contains number units
depends upon the amount we will pay. These units will be given
to energy meter system to activate and it will supply power to
home till that units are consumed and we have recharge same
card again.
EE43
Protection And Control Of Low Voltage
Motors Used In Industrial Applications.
The motor will be protected from over voltage, current,
temperature and ground fault conditions. This system
immediately switches off the motor whenever abnormal condition
occurs and intimate to control room through RF communication.
EE44
Flexible load sharing of transformer with
GSM SMS
It continuously measure the load current and it shares this load
with another transformer when the load is more and send an alert
through message. The user can also share directly whenever he
wants just by sending message
EE45
Agriculture field motor control system
using GSM
Motors in the field are controlled with the help of predefined
SMS.
EE46
Industrial Electrical Devices Control
System
By this project, we can control the devices in the industries by
sending predefined SMS to the controlling unit.
EE47
GSM based DC Motor Speed and
Direction Control
The speed and direction of DC motor can be controlled by
sending predefined SMS to the system
EE48
Cell Phone based Street Light Controlling
System with light failure indication
system.
The on and off controls of the street lights can be done using
GSM technology. If any light does not work then that information
is sent as message to electricity department.
EE49
Temperature Measurement over GSM
Mobile
Temperature sensor is used to measure the temperature in a
particular room and this measured value is sent through GSM to
the user mobile.
EE50
Password protected GSM based Device
control.
Controlling the devices from remote places only by authorized
persons.
EE51 Fingerprint based Access Control system Security is provided in restricted areas using fingerprint

Vision Solutions
VisionGroups
technology. The persons are asked to give their fingerprint and
the system compares this fingerprint with the already stored
information in the system and only allows into if it is an
authorized one.
EE52
Finger print based elevator (lift) operating
system.
Only authorized persons are allowed to access the lift controls.
EE53
Low Cost Wireless Sensor Network In
Field Operation Monitoring Of AC
Motor.
The motor will be protected from over voltage, current,
temperature and ground fault conditions. This system
immediately switches off the motor whenever abnormal condition
occurs and intimate to control room through RF communication.
EE54
A Zigbee Smart Energy Meter
Implementation For Energy Efficient
Buildings.
In This system one control system collects the data from different
meters in the building and we can control the appliances of each
floor through this control system.
EE55
Development of a smart power meter for
AMI based Zigbee communication
Advanced Metering Infrastructure (AMI).
This will be useful in heavy apartment's .individual meters data
will be collected and maintained by main system .this main
system sends collated data to electricity board.
EE56
Remote Power On/Off Control And
Current Measurement For Home Electric
Outlets Based On A Low-Power
Embedded Board And Zigbee
Communication
We can control the home appliances through Zigbee remote and
this system will display the power consumed by the loads.
EE57
Remote-Controllable and Energy-Saving
Room Architecture Based on Zigbee
Communication.
In this we can control the loads through Zigbee remote or they
will also be controlled automatically to save the power.
EE58
Applications of Short Range
Technologies to Industrial Automation: A
Zigbee Approach.
Industrial devices are monitored and controlled using Zigbee
Technology.
EE59
System for Measuring Power Parameters
with Zigbee Connectivity.
This system measures the power from each home and sends to
central system which is useful in apartments.
EE60
Wireless Data Encryption and Decryption
Using Zigbee
Which used in security applications
EE61
Zigbee Based Automated Irrigation
System.
Using Zigbee this system controls the irrigation system
automatically.
EE62
Bluetooth Robot with CMOS image
sensor(SPY ROBOT)
We can control this robot through Bluetooth from PC and the
video sent by robot can be seen in TV or PC

Vision Solutions
VisionGroups
EE63
Remote controlled home automation
using Bluetooth
With this we can control home appliances like lights, fan, motor,
etc through Bluetooth. This is safe and secured.
EE64
Bluetooth based industrial data
acquisition system
This project measures different parameters in industry like
voltage, current and temperature and transmit this data to PC
continuously through Bluetooth.
EE65
Industrial devices controlling system
using Bluetooth
With this we can control industry appliances like machines and
motors through Bluetooth. This is safe and secured.
EE66
Intelligent electricity billing system using
Bluetooth
This system receives the units consumed from various meters and
generates the bill accordingly. This saves the cost, time and
manpower.
EE67
Touch screen based smart home
automation
We can control the home appliance just by smart touch
EE68 Electrical parameters data logger
In this we will continuously measure and display electrical
parameters like voltage, current, frequency and temperature
EE69
Smart horn for vehicles with alcohol
detection for drivers
This system reduces the sound pollution that is generated by
unnecessary use of horn. This controls the horn intensity depends
upon vehicle distance and also gives the special sound when
object is detected at back side if vehicle moves backside and this
system only allows for driving if driver does not consume alcohol
EE70 Smart blind stick with ultra sonic sensor.
This stick gives different sound intensity depends upon the object
distance from person or we can play some voice also depends
upon distance.
EE71
PIR sensor based power saver for
auditorium and conference halls.
This project is used to save the power in conference halls and in
auditoriums. When there are no persons in the hall ,then lights
and fans will be switched off automatically
EE72
Intelligent security and safety system for
colleges and industries
This project detects fire accidents, gas leakages and also alert
through SMS when main door is closed without closing any other
room entrance or if any other door is opened without opening
main door
EE73
An Efficient Monitoring Of Substations
Using Microcontroller Based Monitoring
System using RF
This system monitors the subsystem to provide safety and
intimate to control room through RF
EE74 Wireless Power Grid Controller
With this we can control the power grid through PC using RF
communication
EE75 RF based industrial Automation System The industrial loads like motors, coolers, etc are monitored and

Vision Solutions
VisionGroups
controlled by a RF remote.
EE76
DC motor speed and direction control
using RF
In this project we can control speed and direction of DC motor
depending on the requirement using RF signals
EE77 Wireless Stepper motor control using RF
The stepper motor direction can be controlled using RF
communication.
EE78
Power Management System in Hotels
using PC.
The various appliances in the hotels are controlled by giving
commands from the PC.
EE79 PC based Hi-tech Home Implementation. We can control the home appliances just by sitting in front of PC.
EE80 Industrial Automation using PC.
The industrial appliances are controlled by the commands issued
from the PC. The controlling unit receives these commands from
the PC and controls the devices according to the commands.
EE81
Industrial electrical appliances control
using IR.
To reduce the manpower for controlling the devices we are
implementing this project. Here we will be controlling devices by
using a general TV REMOTE.
EE82
DC motor speed and direction control
using IR.
A DC motor is controlled using wireless communication. In this
project we can control the speed of the dc motor and its direction.
EE83 Stepper motor control using IR
The direction of the stepper motor can be controlled using an IR
remote.
EE84
Automatic Room light controller with
visitor counter using IR.
This project displays the number of persons present in the room
and controls the light according to the intensity of daylight.
EE85 Auditorium Controlling System The lights and fans in auditorium are controlled by IR remote.
EE86
Shopping Malls Security and Power
Management System using IR
The design of security and the method of consuming the power in
the shopping malls are carried out in this project.
EE87 AC motor speed control using TRIAC
The speed of AC motor can be varied rapidly on and off by
TRIAC.
EE88
Phase Sequence Indicator and Controlling
System.
The controlling unit continuously whether 3-phase is coming
from the line or not so as to run the motors which run only with
3-phase. If 3-phase is not coming, the controlling unit
automatically shuts down the system.
EE89 Boiler Monitoring and Control System.
The temperature is measured and controlled for the industrial
boilers.
EE90 Involuntary Industrial Power Scheduler The power management in the industries can be done effectively

Vision Solutions
VisionGroups
using Embedded System. using this project.
EE91
Power Saver for Advertisement
Hoardings using RTC.
This system switches on the lights only at preprogrammed
timings using RTC thus saving the power up to the maximum
extent.
EE92
Solar Tracker for acquiring maximum
power.
The project aims at designing a system that would sense and
follow the position of the sun and rotate the panel in the direction
of the sun to obtain maximum power output.
EE93 Water Scheduling for Municipalities
Water supply to different localities is done on time basis. The
supply will be automatically cut once the time allotted to that
particular locality lapses.
EE94
Electronic Security System for
Homes/Industries with auto dialer.
This system provides security to the homes or offices by
interfacing sensors with the controlling units. If anything goes
wrong, the system automatically dials up to the predefined
number and also activates the alert system.
EE95
Energy Saver for Automatic Room Light
Controller with Visitor Counter
The system aims at saving the power by switching on/off the light
depending upon the sensor output. It also counts the number of
persons present in the hall and displays this value on the LCD.

Eee hardware list

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Eee hardware list

Similar to Eee hardware list (20)

More from Vision Solutions

More from Vision Solutions (20)

Recently uploaded

Recently uploaded (20)

Eee hardware list