c:\ bstat
C:\\> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is the IP address of your external DNS server.
Type set q=MX, and then press ENTER.
Type , where domain name is the name of an external mail domain, and then press ENTER. The
mail exchanger (MX) resource record for the domain that you entered should be displayed. If the
MX record is not displayed, DNS is not configured to resolve external domain names.
Tracert a command-line utility that you can use to trace the path that an Internet Protocol (IP)
packet takes to its destination C;\\ tracert mediacollege.com Tracing a route to
mediacollege.comToolGeneral Job DescriptionExample CommandExample Specific
DescriptionHostnameHostname is the program that is used to either set or display the current
host, domain or node name of the system. These names are used by many of the networking
programs to identify the machine. The domain name is also used by NIS/YP.C:\\> hostnametype
hostname at the command prompt to see the hostnameIpconfigA console application that
displays all current TCP/IP network configuration values and can modify Dynamic Host
Configuration Protocol DHCP and Domain Name System DNS settings IPCONFIG /all
Display full configuration information Nbtstata diagnostic tool for NetBIOS over TCP/IP.Its
primary design is to help troubleshoot NetBIOS name resolution problems
c:\ bstatDisplay protocol statistics and current TCP/IP connections using NBTNetdiagNetdiag is
a set of pre-defined commands that can be used from the console of the K1000 that can be used
by support and customers to help troubleshoot issues regarding the appliance.netdiag [/q] [/v]
[/l] [/debug] [/d:DomainName] [/fix] [/DcAccountEnum] [/test:TestName] [/skip:TestName]
[/?]/q : Specifies quiet output and displays error only
/v : Specifies verbose output.
/l : Sends the output of the Netdiag results to a Netdiag.log file
/d:domain_name: Used to locate domain controllers in a specified domain
/fix:This parameter detects and correct issues with DNS.
/dcaccountenum: Enumerates the computer accounts of the domain controller
/test: TestName : Specific the test to perform. Types of available tests have been described
above.
/skip: testName : To skip any type of test.Netstata useful tool for checking your network
configuration and activity netstat -a list out all the current connectionsNslookupa network
administration tool for querying the Domain Name System (DNS) to obtain domain name or IP
address mapping or any other specific DNS record
C:\\> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is .
c bstatC nslookupDefault Server pdc.corp.example.comAdd.pdf
1. c: bstat
C:> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is the IP address of your external DNS server.
Type set q=MX, and then press ENTER.
Type , where domain name is the name of an external mail domain, and then press ENTER. The
mail exchanger (MX) resource record for the domain that you entered should be displayed. If the
MX record is not displayed, DNS is not configured to resolve external domain names.
Tracert a command-line utility that you can use to trace the path that an Internet Protocol (IP)
packet takes to its destination C; tracert mediacollege.com Tracing a route to
mediacollege.comToolGeneral Job DescriptionExample CommandExample Specific
DescriptionHostnameHostname is the program that is used to either set or display the current
host, domain or node name of the system. These names are used by many of the networking
programs to identify the machine. The domain name is also used by NIS/YP.C:> hostnametype
hostname at the command prompt to see the hostnameIpconfigA console application that
displays all current TCP/IP network configuration values and can modify Dynamic Host
Configuration Protocol DHCP and Domain Name System DNS settings IPCONFIG /all
Display full configuration information Nbtstata diagnostic tool for NetBIOS over TCP/IP.Its
primary design is to help troubleshoot NetBIOS name resolution problems
c: bstatDisplay protocol statistics and current TCP/IP connections using NBTNetdiagNetdiag is
a set of pre-defined commands that can be used from the console of the K1000 that can be used
by support and customers to help troubleshoot issues regarding the appliance.netdiag [/q] [/v]
[/l] [/debug] [/d:DomainName] [/fix] [/DcAccountEnum] [/test:TestName] [/skip:TestName]
[/?]/q : Specifies quiet output and displays error only
/v : Specifies verbose output.
/l : Sends the output of the Netdiag results to a Netdiag.log file
2. /d:domain_name: Used to locate domain controllers in a specified domain
/fix:This parameter detects and correct issues with DNS.
/dcaccountenum: Enumerates the computer accounts of the domain controller
/test: TestName : Specific the test to perform. Types of available tests have been described
above.
/skip: testName : To skip any type of test.Netstata useful tool for checking your network
configuration and activity netstat -a list out all the current connectionsNslookupa network
administration tool for querying the Domain Name System (DNS) to obtain domain name or IP
address mapping or any other specific DNS record
C:> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is the IP address of your external DNS server.
Type set q=MX, and then press ENTER.
Type , where domain name is the name of an external mail domain, and then press ENTER. The
mail exchanger (MX) resource record for the domain that you entered should be displayed. If
the MX record is not displayed, DNS is not configured to resolve external domain
names.PathPingPathping is a Windows based command-line tool used to provide information
about the path data takes to its intended destination, network latency and network loss at
intermediate hops between a source and destinationpathping -n server-1In command
prompt,Tracing route to server-1Pinga computer network administration software utility used to
test the reachability of a host on an Internet Protocol (IP) network.ping iinet.net.auFirst you’ll
see the replies for each packet sent in the ping test. A Windows ping test will typically send 4
packets.Routea command used to view and manipulate the IP routing table in both Unix-like and
Microsoft Windows operating systemsC: routeCommand to manually configure the routes in
3. the routing table
Solution
c: bstat
C:> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is the IP address of your external DNS server.
Type set q=MX, and then press ENTER.
Type , where domain name is the name of an external mail domain, and then press ENTER. The
mail exchanger (MX) resource record for the domain that you entered should be displayed. If the
MX record is not displayed, DNS is not configured to resolve external domain names.
Tracert a command-line utility that you can use to trace the path that an Internet Protocol (IP)
packet takes to its destination C; tracert mediacollege.com Tracing a route to
mediacollege.comToolGeneral Job DescriptionExample CommandExample Specific
DescriptionHostnameHostname is the program that is used to either set or display the current
host, domain or node name of the system. These names are used by many of the networking
programs to identify the machine. The domain name is also used by NIS/YP.C:> hostnametype
hostname at the command prompt to see the hostnameIpconfigA console application that
displays all current TCP/IP network configuration values and can modify Dynamic Host
Configuration Protocol DHCP and Domain Name System DNS settings IPCONFIG /all
Display full configuration information Nbtstata diagnostic tool for NetBIOS over TCP/IP.Its
primary design is to help troubleshoot NetBIOS name resolution problems
c: bstatDisplay protocol statistics and current TCP/IP connections using NBTNetdiagNetdiag is
a set of pre-defined commands that can be used from the console of the K1000 that can be used
by support and customers to help troubleshoot issues regarding the appliance.netdiag [/q] [/v]
[/l] [/debug] [/d:DomainName] [/fix] [/DcAccountEnum] [/test:TestName] [/skip:TestName]
[/?]/q : Specifies quiet output and displays error only
4. /v : Specifies verbose output.
/l : Sends the output of the Netdiag results to a Netdiag.log file
/d:domain_name: Used to locate domain controllers in a specified domain
/fix:This parameter detects and correct issues with DNS.
/dcaccountenum: Enumerates the computer accounts of the domain controller
/test: TestName : Specific the test to perform. Types of available tests have been described
above.
/skip: testName : To skip any type of test.Netstata useful tool for checking your network
configuration and activity netstat -a list out all the current connectionsNslookupa network
administration tool for querying the Domain Name System (DNS) to obtain domain name or IP
address mapping or any other specific DNS record
C:> nslookup
Default Server: pdc.corp.example.com
Address: 192.168.6.13
> server 10.255.255.255
Default Server: dns1.example.com
Address: 10.255.255.255
> set q=mx
> contoso.com.
At a command prompt, type Nslookup, and then press ENTER.
Type server , where IP address is the IP address of your external DNS server.
Type set q=MX, and then press ENTER.
Type , where domain name is the name of an external mail domain, and then press ENTER. The
mail exchanger (MX) resource record for the domain that you entered should be displayed. If
the MX record is not displayed, DNS is not configured to resolve external domain
names.PathPingPathping is a Windows based command-line tool used to provide information
about the path data takes to its intended destination, network latency and network loss at
intermediate hops between a source and destinationpathping -n server-1In command
prompt,Tracing route to server-1Pinga computer network administration software utility used to
test the reachability of a host on an Internet Protocol (IP) network.ping iinet.net.auFirst you’ll
5. see the replies for each packet sent in the ping test. A Windows ping test will typically send 4
packets.Routea command used to view and manipulate the IP routing table in both Unix-like and
Microsoft Windows operating systemsC: routeCommand to manually configure the routes in
the routing table