A two-component epoxy for repair and maintenance for carbon steel and a range of aged coating surfaces.

1. Product profile :
A two-component epoxy for repair and maintenance for carbon steel and a range of aged coating surfaces.
Tobmastic 01
Two-component epoxy for repair and maintenance for carbon steel
. PROPERTY PROFILE
 Excellent protection in less severe environments
 Low film thickness version
 Provides all the benefits of Tobmastic 01 products
and the same excellent protection but at lower dry
film thicknesses
 Substrate tolerant
 Plasticizer-free
 Free From nonylphenol and alkenylphenol
 Can be subject ed to mechnical loads
 Can be subjected to chemical loads
Application examples:
 Anti-corrosive coating for steel bars
 Consumer markets
 Metals in Shops /Roof / basement
 Fabrication halls
 Assembly areas
 Food industry
 Butcher operations
 Bakeries
Recommended Application
 Priming coat -Tobmastic 01 requires no blast cleaning
reducing time and cost with no compromise in
protection, It can be applied on most clean and sound
surfaces – reducing downtime.
Tobmastic 01 is optimal solution for difficult to reach
areas, where good surface preparation is not possible
or desirable.
Tobmastic 01 can be used over most generic types of
coatings. High surface tolerance and wetting
properties give deep penetration and thus better
adhesion and durability in harsh environments,
combined with a wider choice of solutions
 Application procedure for Anti-corrosive coating:
1. Ensure surface of steel bars to be coated is dry, clean
and free from oil, grease and other contaminants.
2. Remove loose rusting particles and dust by Wire Brush
or any suitable mechanical tools.
3. Mix Tobmastic 01 Resin & Hardener in specified pro-
portion in disposable bowl thoroughly.
4. Apply mix mass uniformly in thin layer on steel bars
with help of brush or spray.
5. If required apply second coat of Tobmastic 01 after 3 –
4 hours of first coat application.
6. Allow to cure for minimum 48 - 72 hrs.
 Mixing ratio
2 : 1 parts by weight (Resin : Hardener)
 Pot-life
At 20 °C and 60% relative humidity approx. 30
minutes. Higher temperatures reduce, lower
temperatures increase pot-life.
 Packaging:
2.0 kg, 10 kg and 45 kg tin containers
 Application rate:
Depending on application between 0.2-0.25 kg/m²
Coverage on Metal (150μ coat)
 Shelf-life:
At least 9 months in closed and unmixed, original
containers stored cool but frost-free
 Drying time
At 20 °C and 60% relative humidity: foot traffic after
12 hours, mechanical loads after 3 days, fully cured
after 7 days. At lower temperatures correspondingly
longer. Protect the applied material from moisture
during the curing process (approx. 24 hours at 20 °C)
since the surface may be disturbed and adhesion
reduced otherwise.
 Tools, cleaning
Smoothing trowel, toothed trowel, rubber wiper,
epoxy roller, spiked roller, mixing equipment, also
positive mixer. Clean tools and equipment
immediately while the material is still fresh with
Tob 100 Thinner.
Art. No. OB 4005 ( A)
Page 1 of 2

2. Page 2 of 2
 Substrate preparation
Ensure surface of steel bars to be coated is dry, clean and free from oil, grease and other
contaminants. Remove loose rusting particles and dust by Wire Brush or any suitable mechanical tools.
INDIA
Tobslak India Pvt. Ltd.
305-c, 3rd floor, Irishtech park,sect-48,sohna road,
Gurugram-122018(HR),INDIA
Email: ccin@tobslak.com, www.tobslak.com
GERMANY
Tobslak International,Eschersheimer,Landstraße 42,
60322, Frankfurt am Main, Hessen, Germany
Phone:(+49) 3221 1226423
Email:info@tobslak.com; www.tobslak.com
Important: The descriptions, designs, and data contained herein are presented for your guidance only. Because there are many
factors under your control which may affect processing or application/use it is necessary for you to make appropriate tests to
determine whether the product is suitable for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE
REGARDING PRODUCTS DESCRIBED OR DESIGNS, OR INFORMATION SET FORTH, OR THAT THE PRODUCTS, DESIGNS, OR DATA
MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCRIPTIONS,
DATA OR DESIGNS PROVIDED BE PRESUMED TO BE A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly
understand and agree that the descriptions, designs, and data furnished by TOBSLAK hereunder are given gratis and TOBSLAK
assumes no obligation or liability for same or results obtained from use thereof, all such being given to you and accepted by you
at your risk.
 Typical Properties: Tobmastic 01
Resin Hardner
Description ₋ Visual Clear Liquid Clear Yellowish brown viscous liquid
Viscosity at 25⁰C mPas ASTMD 2196 500 - 1000 8,500 - 14,000
Color GS ASTMD 1544 ₋ Max. 10
Color APHA ASTMD 1209 Max. 100 ₋
Test Unit Reference
Value
 Typical Mix Properties: Tobmastic 01
Test Unit Reference Value
Mixing ratio (Resin : Hardener) w/w ₋ 100 : 50
Mixing ratio (Resin : Hardener) v/v ₋ 2 : 1
Mix viscosity at 25⁰C mPas ASTMD 2196 800 - 1200
Pot life minutes ASTMD 2471 65 - 85
Specific Gravity (Mix mass) ₋ ₋ 1.05
Surface dry hours ASTMD 5895 5
Touch dry ASTMD 5895 8
Elongation % ASTMD 638 Max. 8
Pull-off Adhesion MPa ASTMD 7234 Min 2.5
The resin and hardener, when stored in their original containers and not exposed to undue heat or humidity as in
outdoor open shades, will have a minimum shelf life of 1 years. As far as possible, direct contact of resin and
hardener with the skin should be avoided as they might cause irritant on sensitive skins. It is advisable to wash off
immediately in case of skin contact. Special barrier creams and cleansing creams are available commercially as
additional safe guards. Please refer MSDS for detail safety instructions.
 Storage & Handling :