Substation 1

1. Bill of quantity against Tender No.06-CE(LZ)/Works/2016-17 for construction of 33/11 KV (1x5MVA) Sub-staion,
RTO Hardoi due to be opened on 6.06.2016
Sl. No. Description of Works Unit Qty.
Unit Rate
(Rs.)
Total
Amount
1
Carriage of all the concerning material from store center to JE's dump store &
from dump store to the site work including loading, unloading and proper
stacking at the site etc.
Material of 33/11 KV S/S
1 33/11 KV T/F 05 MVA No. 1
2 33 KV Pin Insulator No. 3
3 Bracing Angle 65x65x6mm No. 3
4 ACSR Weasel Conductor KM 0.25
5 33 KV Line Isolator Nos. 1
6 33 KV Bus Isolator Nos. 1
7 33 KV Post Insulator Nos. 12
8 33 KV Lightening Arrestor No. 6
9 90 LBS Rail Pieces for T/F & Gantry Mtr. 52.9
10 33 KV VCB No. 2
11 control panel I/C for 33 KV Single T/F Control Panel No. 1
12 control panel I/C for 33 KV Single Feeder No. 1
13 CT 200/100/1-1A No. 6
14 MS Angle 65x65x6 Kg. 300
15 Top Channel 100x50 Kg. 500
16 Ms Angle 50x50x6 Kg. 465
17 MS Channel 125x65 Kg. 1489
18 33 KV Disc Insulator 70 KN No. 36
19 MS Angle 75x75x6 Kg. 396
20 MS Round Bar 32 mm Kg. 4.47
21 ACSR Panther Conductor KM 0.16
22 11 KV VCB 600/300, 5A, 350 MVA I/C No. 1
23 11 KV Outgoing 200/100/5A 350 MVA No. 4
24 11 KV 3x300 sq.mm XLPE Cable Mtr. 60
25 11 KV 3x185 sq.mm. XLPE Cable Mtr. 240
26 11 KV Cable jointing kit 3x120 sq.mm I/D & O/D No 8
27 24 Volt Battery & Battery charger with cabinet No 1
28 63 KVA 11/0.4 T/F No. 1
29 PCC Pole 8.5 mtr. long No. 8
30 STP 11 mtr. long No. 4
31 LT Cable 3x5x70/3.5mm Mtr. 60
32 11 KV Pin Insulator No. 12
2
Construction of Toe wall around the outdoor Switchyard of the S/s of size 0.75
Mt.At Base and 0.23 Mt. At top as per RESSPO Norms by lst class bricks in
the ratio 1:6, Base concreting of the wall to be done in ratio 1:6:12 and plaster
12 mm thick in ratio 1:4.
RMT 110
3
Fabrication of switchyard fencing with wire mesh 10SWG(37mmx50mm) as
per drawing along with Fabrication of one number gate made of MS Angle,
MS Channel, MS Flat together with locking arrangement, its Installation
including the cost of civil material, angle 50x50x6mm.
RMT 110

2. 4
EARTH MAT Laying of earth mat in the switchyard by laying of M.S. Round
of 32 mm dia in 500 mm deep trenches with M.S. Round 32mm dia,3Mtr.
Long earth electrodes as per drawing. The work includes welding of the M.S.
Round, connecting all steel structures in the switchyard with the earth mat by
means of G.I. strips of size 50x6mm as per item below. (M.S. Round bar
32mm provided by Department )
A) Excavation of earth for laying mat RMT. 570
B) Driving of earth electrode. No. 65
C) Laying of earthmat (M.S.) Bar including cutting, shaping and binding etc) RMT. 570
D)
Preparation of joints, proper making and welding; of main earthmat bar joints
and applying, bitumen, bitumen impregnated on joints I.e. End Joints. Cross
Joints, Lap Joints.
No. 265
E)
Welding of riser strip with earthmat and department structure body (One set
means one riser strip welding to main equipments).
RMT 200
5
Construction of plinth of size 3.46x3.46 Mtr. For 5 MVA T/F having 0.4 Mtr.
suitable for 10 MVA T/F. above ground level,0.5Mtr below ground level . The
work including excavation of foundation .base concreting in CC 1:6:12 ratio
(cement ,fine sand & brick ballast)first class brick work in cement morter of
ratio 1:4 foundation CC in 1:4:8 ratio (cement ,fine sand & brick blast) and
RCC working ratio 1:2:4 (cement ,coarse sand and store grit of 20mm gauge
using MS Bars of 10mm dia( tor ) in reinforcement including its cutting
,bending &binding in required shape .The work also includes laying of 2 Nos.
3.46 Mts.Long each rail places complete with cutting welding & proper fitting
etc. The plinth will be made as per drawing and shall be plastered/ finished on
top and sides of the plinth.
Job. 1
6(A)
FABRICATION, ERECTION & GROUTING OF S/S STRUCTURE.
TERMINAL GANTRY and 33KV main Bus Bar Structure- Fabrication,
erection, & grouting of gantry using rail pole and channel as per RESPO Drg.
No. RES- 38.
Job. 3
(B)
ISOLATOR STRUCTURE Fabrication of isolator structures 3.5 Mtr. In height
as per drawing No. RES 39.Digging of two Nos .pits of size 1.075x0.9x0.3
Mtr. providing stone pad at the bottom of the pit and grouting pad at the bottom
of the pit and grouting of two legs of the isolator structure in CC (cement
coarse sand and stone grit of 20m.m gauge)of the ratio 1:4:8 in block of
1.075Mtrx0.3 mm including supply of all T&P complete in all respect. The
work includes dragging, shifting upto 40 mtrs. Raising and erecting the two
legs with runner in proper alignment, and level and plumb .Both plinths of the
isolator structure shall be properly finished with smoothening of edges.
Job. 2
(C)
LIGHTENING ARRESTOR &P.I..STRUCTURE Fabrication of lightening
arrestor&P.I. structure.as per drawing No. Res-39 Digging of two Nos. pits of
size 1.075x0.3x0.3Mtr providing stone pad at the bottom of the pit and
grouting of two legs of the above structures in CC (Cement, coarse sand and
stone grit of 20mm gauge) of ratio 1:4:8 in block of 1.075Mtr X0.3Mtr
including supply of all civil material complete in all respect. The work includes
dragging, shifting up to 40Mtrs. raising and erecting the two legs with runner
of isolator in proper alignment, level and plumb. Both plinths of the structures
shall be properly finished with chambering of edges etc.
Job. 4
(D)
C.T.STRUCTURE& P.T.STRUCTURE Fabrication of CT structure&PT
structure .as per drawing No. Res-39 Digging of two Nos. pits of size
1.075x0.3x0.3Mtr providing stone pad at the bottom of the pit and grouting of
two legs of the above structures in CC (Cement, coarse sand and stone grit of
20mm gauge) of ratio 1:4:8 in block of 1.075Mtr X0.3Mtr including supply of
all civil material complete in all respect. The work includes dragging, shifting
up to 40Mtrs. raising and erecting the two legs with runner of isolator in proper
alignment, level and plumb. Both plinths of the structures shall be properly
finished with chambering of edges etc.
Job. 2
(E) Construction a plinth 2x2x1.5 with RCC top of 63 KVA transformer. Job. 1

3. 7
PLINTH FOR VCB Construction of plinth of size 2.0 mtr x 1.5 mtr x 0.9 mtr
suitable for erection of upper structure for 33KV VCB including grouting of
anchor bolts in proper alignment and level. Scope of work includes excavation
of foundation base concreting in CC 1:6:12(cement, fine sand & brick ballast),
1st class brick work in cement mortar of ratio 1:4 CC in ratio 1:4:8 and RCC
work in ratio 1:2:4(cement coarse sand and stone grit of 20mm gauge) as per
drawing.
Job.. 2
8(A)
ERECTION & INSTALLATION OF 33/11KV,5MVA TRANSFORMERS
Erection and Installation of 33/11kV,5MVA transformer in a leveled position
on the plinth. The work include shifting of transformer to the site of installation
within the substation premises, assembling fixing and fitting of all accessories
and filling of transformer oil to the desired level and insuring that there is no
leakage. All the jump ring & connection are included in the scope of work.
Job. 1
(B)
Earthing by way of boring and lowering of "B" class GI pipe 50mm dia from
ground upto the water level (minimum 40 meter deep) as per standard practice
earthing including material supplied by contractor.
Job.. 2
(C)
Fabrication and grouting of M.S Channel 100x50x6mm in L shape & in proper
size and alignment to provide support for the two separate earthing strips for
power transformer neutral including supply and fixing of two nos. Flexible
copper bonds for neutral ear thing.
Job. 1
(D)
Fabrication and erection of cable support made of two pieces of M.S channel
100x50mm,3.0Mtr. long joined to each other by means of 5 Nos.M.S Flat
50x6mm places of size 150mm long each by welding at equal intervals as per
drawing and grouting in a block of size300x300x700mm complete with one
coat of ready mixed primer and two coats of aluminum paint. This includes
providing of four nos M.S clamp made of M.S flat holding the cable including
nuts and bolts and fixing of XLPE Cable.
Job. 1
9
INSTALLATION OF ISOLATORS Assembling and installation of line /bus
isolator on the isolator structure adjusting of opening mechanism in proper
alignment so as to ensure smooth operation of the same in case of line isolator
proper operation of earth links shall also be insured. The work includes
fabrication for proper flexing if required.
Set 2
10
INSTALLATION OF LIGHTENING ARRESTORS Assembling and
installation Mounting of 3Nos (1 set) lightening arrestors on the L.A.Structure
complete with making earth connections (separate) and line connections the
work includes fabrication for proper fixing if required.
Set 2
11
INSTALLATION OFPOST INSULATOR Assembling and installation
Mounting of 6Nos (1 set) POST INSULATOR on the PI.Structure complete
with making earth connections (separate) and line connections the work
includes fabrication for proper fixing if required.
Set 2
12
INSTALLATION OF CT Installation of 3 Nos.(1 set) CTs on the /CTs
structure . Along with C.T. J/B. The work includes fabrication for proper fixing
if required.
No. 6
13
INSTALLATION OF PT Installation of 3 Nos.(1 set) PTs on the /PTs structure
. The work includes fabrication for proper fixing if required.
Set 0
14
INSTALLATION OF VCB Installation of 33KV VCB complete work
including commissioning.
No. 2
15(A)
INSTALLATION OF SWITCHGEARS IN CONTROLROOM
Job. 5
Shifting carefully & safely 11KV I/C & O/G switchgear, 11 KV Bus Coupler
from outside of the switchgear room, including grouting the two
No.100x50x6mm channels pieces (each 800mm long including cutting to size)
and foundation bolts in 1;2:4 CC (including cutting of CC of the floor and
finishing of floor)as per direction of Engineer in charge, placing and fixing of
switchgear on foundation providing G.I. Nuts & Bolts of proper size in proper
position and alignment and checking, complete work with Mounting of P.T on
incoming S/G.
(B)
Fixing and making bus bar connections in between all switchgears after
cleaning and tapping with H.T. Tape, empire tape and PVC tape properly,
providing and fixing of 6 mm thick Bakelite separators and plugging of all
opening & holes with plastic compound complete work including cost of all
material (except copper Bus Bars) strictly to the satisfaction of site in- charge.
Job. 1
(C)
Shifting carefully & installation of 33KV double circuit transformer control
panel in control room including grouting of above.
Job. 1

4. (D)
Shifting carefully & installation of 33KV single circuit line control feeder
panel in control room including grouting of above.
Job 1
16
EARTHING OF 11 KV & 33KV SWITCHGEARSA) Laying of Earth mate
for earthing of indoor equipments by means of M.S strip 50x6mm connecting
to Pipe type earthing as per RESSPO norms. Joints will be welded with high
quality are welding.
Job 1
17
Installation of 24 Volt 15 AH sine wave Battery and battery Charger Complete
and Charger including its commissioning.
Job. 1
18
Fabrication and erection of exposer type D/P for 11 KV line, on 11m long ST.
pole with fixing of necessary clamp & other accessories like one no. Top
channel 100x50.-1.3m long ,Angle 65x65x6mm , its grouting 300mm above
ground Level, painting of pole contractor shall provide necessary clamps&
other accessories like GI pin TPMO , Fuse set Disc fitting etc.
Job. 4
19 (A)
H.T.CABLE LAYING
Mtr. 60
Laying & dressing of 11KV,3X300sq.mmunder ground cable from 5MVA T/F
to 11KV incoming switchgear in the trench 450 mm wide,900mm deep
providing 150mm fine sand, cushion beneath and 150mm fine sand cushion
above the cable. The cable shall be duly protected by bricks, sand & stone slab.
The work includes supplying of fine sand , bricks and stone slab are refilling
and ramming of the left out soil ,closing the trench and leveling. Spare cable
shall be left and burried in the trench in the shape of rings at both ends cable
laying work includes unrolling cutting mage ring and sealing both ends of the
cable.
(B)
Laying & dressing of 11KV,3X185 sqmm. under ground cable in the trench
450 mm wide,900mm deep providing 150mm fine sand, cushion beneath and
150mm fine sand cushion above the cable. The cable shall be duly protected by
Ist class bricks/stone slab. The work includes supplying of fine sand & bricks
& stone slab and refilling and ramming of the left out soil and leveling. Spare
cable shall be left and buried in the trench in the shape of rings at both ends.
Mtr. 240
20(A)
FIXING OF 11KV CABLE ENDS
Job. 2
Fixing of 11KV,3x300sq.mm XLPE Cable out door jointing kits after
carefully removing the insulation of the cable duly plumbing and taping of
cable providing, fixing and crimpling of proper size good quality lugs and
complete work including cost of material such as insulating tapes, cotton tape,
plumbing material and lugs etc.
(B)
Fixing of 11KV,3x300sq.mm XLPE Cable In door jointing kits on switchgears
after carefully removing the insulation of the cable,duly plumbing and taping
of cable providing,fixing and crimpling of proper size good quality lugs,duly
plumbing and taping of cable with good Quality of cotton tape ,empire tape,
HT Tape and PVC Tape, properly fixing of lugs on switchgears and boxes
complete in all respect including cost of material such as insulating Tapes
,cotton Tape,Plumbing material and lugs etc.
Job. 2
(C)
Fixing of 11KV,3x185 sqmm. XLPE Cable out door jointing kits after
carefully removing the insulation of the cable duly plumbing and taping of
cable providing, fixing and crimpling of proper size good quality lugs and
complete work including cost of material such as insulating tapes, cotton tape,
plumbing material and lugs etc.
Job. 4
(D)
Fixing of 11KV,3x185 sqmm. XLPE Cable In door jointing kits on
switchgears after carefully removing the insulation of the cable, duly plumbing
and taping of cable providing, fixing and crimpling of proper size good quality
lugs, duly plumbing and taping of cable with good Quality of cotton tape,
empire tape, HT Tape and PVC Tape, properly fixing of lugs on switchgears
and boxes complete in all respect including cost of material such as insulating
Tapes ,cotton Tape, Plumbing material and lugs etc.
Job. 4
(E)
Hosting of 11kv cable with 100 mm Dia ,3.5mtr. Long MS Pipe on the feeder
cable before mounting the cable on the double pole,lifting,mounting and
clamping of 11KV feeder cable boxes on the feeder double pole structure and
making connection including supply of cable mounting clamps The work
includes the sealing of GI Pipes lower end of the Pipe is to be buried into the
earth by about one foot. MS pipe supplied by contractor
Job. 4
(F)
Hosting of 11 KV cable to 11K.V. switchgear & 33/11 KV T/F & 11/0.4 KV
Cable Stand
Job. 6

5. 21
33K.V. SECTIONAL BUS BAR AND STRINGING Stringing of 33KV bus
bar using of ACSR Panther Conductor including fixing of Disc insulators.
Strings and tension fitting complete with sagging of bus bar etc. and making
vertical/Horizontal jumper connection through PG Clamps and connecting all
the equipments with each other through connecting clamps. Work includes all
the jump ring from terminal gantry to bus bar and from bus bar to transformer
(2no. T/f bay's)
Job. 1
22(A)
STATION/SWITCYARD LIGHTING
Job. 4
Erection of 11 Mt. STP after excavation of earth in any type of soil and
grouting of CC in ratio 1:4:8 (cement coarse sand & brick ballast) as per
RESSPO Drg. With plinth.
(B)
Fixing & supply of 250 watt. sodium vapor lamp complete fitting and of
standard quality ISI mark with water light fittings, elbow etc. complete in all
respect and suitable for above supports.
Job. 4
(C)
Supply & Laying of 3.5 x 70/35 Sq.mm PVC LT cable from 11/.04 kv,63KVA
T/F to LT Distribution Board in switchgear room after digging the trench,
laying cable and refilling of trench including connection at both ends after
providing and crimpling of lugs of proper size, complete work.
Job. 1
(D)
Supply and laying of 2 x 6 sq. mm. aluminum cable from S.G. room to street
light supports after digging of trench, laying of cable, providing a brick on top
of cable , refilling of trench, making connections at poles with street light
fittings, complete in all respect.
Job. 1
23
Construction of cable trench of size 300x300 mm including brick work 1:4 in
wall of the trench brick ballast work in 1:5:10 on foundation plaster 12 mm
thick with coarse sand 1:4 and surface finishing with cement : providing MS
strip at an interval of 0.5 M & MS angle running on both the edges of trench.
RMT 60
24
Construction of welded frame type control cable trench cover 0.5 M long
suitable for trench including cost of MS/Torr Bar.
RMT 160
25
Supply and Laying of following size copper. control cable through
underground/cable trench/trenching SGR interlinking through proper
connections. transformer control panel/protection board /Battery and Battery
Charger/Bunch jolts Relay 33/11 KV Transformer junction box/ 33KV VCB,
CTs etc as per site conditions.
(A) 2x2.5mm2 RMT 100
(B) 4x2.5mm2 RMT 100
(C) 6x2.5mm2 RMT 0
27 Supply and fixings of CT junction box No. 2
28 Painting of all structures & equipment Job. 1
29 Erection &Installation of 63 KVA transformer with complete fittings Job. 1
30 Soil filling of yard Cum. 500
31 Testing & Commissioning of all equipments Job 1
Note:-All Centralized Materials to be supplied by Department.
Any other material, filtting i.e. all connections, PG Clamps, gun fitting etc.accessories, equipemtn, apparatus which
might not have been mentioned in the bid document but which are used and necessary for completion of the work
as per RESSPO Norms/relevant ISS shall be arranged by the contractor. All T&P and labour required for successful
completion of work shall be supplied by the contractor.
Date :
Signature of contractor with seal
Place :

6. Bill of quantity against Tender No.07-CE(LZ)/Works/2016-17 for construction of 33 KV & 11 KV Line of 33/11 KV
(1x5MVA) Sub-staion, RTO Hardoi due to be opened on 6.06.2016
SI.NO Particular Item Unit Qty. Rate Amount
Part A- 33KV
1
Safe loading carriage including unloading & proper stacking of
following store materials from ESC Hardoi/JE Store to Site of
Work.
i STP-SP-55 No. 32
ii 33 KV "V" type cross Arm No. 50
iii 33 KV Pin Insulator No. 177
iv 9 Mtr. PCC Pole No. 36
v MS Angle Iron 65x65x6mm bracing with 4 clamps No. 18
vi MS Channel 125x65x3200 mm No. 13
vii 11 KV Disc Insulator B&S Type 70 KN No. 168
viii 33kvx300 XLPE cable Mt 200
ix GI Wire 6 SWG Kg. 70
x stay wire7/8 kg 300
xi Earth wire 16 swg kg 150
xii MS channel 75x40 kg 544
xiii ACSR Dog Conductor Km. 10.815
xiv 33 KV 3x300 sq. mm. O/D Kit No. 4
2
Fabrication & erection of single pole for 33 KV line on 11 M long
ST Pole with fixing of necessary clamp & other accessories like 1
No. 11 KV V-type cross arm 1 No. Grounding Angle. its grounting
in ration 1:4:8, plinthing 300 mm above ground level. Painting of
pole with one coat or red oxide two coats ot enamel paint ISI
mark, contractor shall provide 3 nos 33 KV G.I. Pin neccessary
clamps, F-bracket. etc.
No. 24
3
Fabrication & erection of single pole for 33 KV line on 9 M long
PCC Pole with fixing of necessary clamp & other accessories like
1 No. 11 KV V-type cross arm 1 No. Guarding Angle. Its
grounting in ration 1:4:8, plinthing 300 mm above ground level
earthing of support.
No. 26
4
Fabrication & erection of Double pole of, 33 KV line on 11 M long
ST Pole with fixing of necessary clamp & other accessories like 1
No. top channel 100x50 mm 3.20 M its grounting in ration 1:4:8,
plinthing 300 mm above ground level. Painting of pole with one
coat or red oxide two coats ot enamel paint ISI mark.
No. 2
5
Fabrication & erection of Double pole of, 33 KV line on 9 M long
PCC Pole with fixing of necessary clamp & other accessories like
1 No. top channel 100x50 mm 3.20 M its grounting in ration
1:4:8, plinthing 300 mm above ground level.
No. 3
6
Fabrication & erection of Double pole Exposer type 33 KV line on
11 MK long ST Pole with fixing necessary clamp & other
accessories like 1 No. top channel 125x65 mm its grounting in
ration 1:4:8, plinthing 300 mm above ground level. Painting of
pole with one coat or red oxide two coats ot enamel paint ISI
mark.
No. 0
7
Fabrication & erection of Three Pole of 33 KV line on 11 M long
ST Pole with fixing of necessary clamp & other accessories like 1
No. top channel 125x50 mm 3.20 M its grounting in ration 1:4:8,
plinthing 300 mm above ground level. Painting of pole with one
coat or red oxide two coats ot enamel paint ISI mark.
No. 0

7. 8
Fabrication & erection of Four Pole of 33 KV line on 11 M long ST
Pole with fixing of necessary clamp & other accessories like 1 No.
top channel 125x50 mm 3.20 M its grounting in ration 1:4:8,
plinthing 300 mm above ground level. Painting of pole with one
coat or red oxide two coats ot enamel paint ISI mark.
No. 1
9
Fabrication & erection of Four Pole of 33 KV line on 9 M long pcc
Pole with fixing of necessary clamp & other accessories like 1 No.
top channel 125x50 mm 3.20 M its grounting in ration 1:4:8,
plinthing 300 mm above ground level. Painting of pole with one
coat or red oxide two coats ot enamel paint ISI mark.
No. 1
10
Eraction of single stud pole support one ST Pole 11 M long with
fixing of necessary clamps and other accessories required for
rerection
No. 0
11 Stringing and sagging of 3 Phase 33 KV line on ACSR Dog
conductor as per RESSPO Norms.
Ckt. K.M 3.5
12 stringing and sagging of two nos. Earth/GI wire with
caddieguarding of above 33 kV line as per RESSPO Norms
RMT 500
13 Providing and fixing of earth red as per norms No. 63
14 nozeling and grouting of stay set (All the civil material and stay
set will be arranged by the contractor)
job 56
15 Removal/lopping and chopping of tree branches which are lying
in route of 33 KV over head line of length approx 1.0 Km
job 1
16 Laying of 33 KV 3x300 sq.mm. XLPE cable
i
Double circuit in normal soil by digging of trench 1050 mm deep.
750 mm wide including supplu of required material 1st class
bricks stone pad & fine sand. The inter axial spacing between
two cable should be in betwewn 0.25 M to 0.40 M. the two cable
must be separated by a partition to single brick and back filling
of digged trecnch and proper leveling. ( All the material required
for laying will be supplied by the cotractor except 33 KV XLPE
cable)
Mtr 70
ii Double circuit in RCC pipe( All the material required for laying
will be supplied by the cotractor except 33 KV XLPE cable)
Mtr 0
iii Cable laying by drill method single circuit Mtr 0
iv For Railway/river/channel/road/drain crossing in MS pipe by
drilling single. ( All the material required for laying will be
supplied by the cotractor except 33 KV XLPE cable)
Mtr 0
17 Installation of heat shrinkable cable jointing kits of following
sizes/types for 33 KV XLPE cable
0
i 33 KV 3x300 sq.mm straight through joints. No. 0
ii 33 KV 3x300 sq.mm outdoor end teminations. No. 4
18 Hosting of 33 KV 3x300 sq.mm. XLPE cable on double pole
including MS Pipe of Size 8" dia 3 M long including its jumpring
complete with clamps nuts and bolts.
No. 0
19 High pressure testing of 33 KV 3x300 sq.mm. XLPE cable. Testing
equipments will be arranged by the contractor.
No. 2
BOQ 11 KV Line RTO Office Hardoi
Part B-11 KV
1
Safe loading carriage including unloading & proper stacking of
following store materials from ESC Hardoi/JE Store to Site of
Work.
i 8.5 mtr. Long PCC Pole No. 38
ii 11 KV "V" type cross Arm No. 68

8. iii 11 KV Pin Insulator No. 231
iv MS Channel 100x50x2240 (Top Channel) No. 9
v MS Angle Iron 65x65x6mm bracing with 4 clamps No. 9
vi 11 KV Disc Insulator B&S Type 45 KN No. 54
vii 11 Mtr. Long STP No. 48
viii ACSR Racoon Conductor Km. 15.45
ix G.I. Wire 6 SWG for guarding Kg 240
x Stay wire 7/10 SWG Kg 270
xi MS Channel 75x40 Kg. 1088
xii Earth wire kg 100
xiii T-off channel No. 6
2
Fabrication & erection of single pole for 11 KV line on 11 M long
ST Pole with fixing of necessary clamp & other accessories like 1
No. 11 KV V-type cross arm 1 No. Grounding Angle. its grounting
in ration 1:4:8, plinthing 300 mm above ground level. Painting of
pole with one coat or red oxide two coats ot enamel paint ISI
mark, contractor shall provide 3 nos 33 KV G.I. Pin neccessary
clamps, F-bracket. etc.
No. 38
3
Fabrication & erection of single pole for 11 KV line on 8.5 M long
PCC Pole with fixing of necessary clamp & other accessories like
1 No. 11 KV V-type cross arm 1 No. Guarding Angle. Its
grounting in ration 1:4:8, plinthing 300 mm above ground level
earthing of support.
No. 30
4
Fabrication & erection of Double pole of end terminations, 11 KV
line on 11 M long ST Pole with fixing of necessary clamp & other
accessories like 1 No. T-off channel 100x50 mm 2.24 M
Guarding Angle. Its grounting in ration 1:4:8, plinthing 300 mm
above ground level. Painting of pole with one coat or red oxide
two coats ot enamel paint ISI mark & Earthing Support.
No. 5
5
Fabrication & erection of Double pole of end terminations, 11 KV
line on 8.5 M long PCC Pole with fixing of necessary clamp &
other accessories like 1 No. T-off channel 100x50 mm 2.24 M
Guarding Angle. Its grounting in ration 1:4:8, plinthing 300 mm
above ground level. Painting of pole with one coat or red oxide
two coats ot enamel paint ISI mark, Earthing Support & one side
cable Support
No. 4
6
Fabrication & erection of Double pole for end termination 11 KV
line on 11 M long ST Pole with fixing necessary clamp & other
accessories like 1 No. top channel 100x50 mm- 2.24 m 01 No
Guarding Angle fabrication of cross bracing. Its grounting in
ration 1:4:8, plinthing 300 mm above ground level. Painting of
pole with one coat or red oxide two coats ot enamel paint ISI
mark & earthing Support.
No. 0
7 Fabrication & eraction of double pole for 11 KV cable exposure
cable on double pole & earthing of support.
No. 0
8
Fabrication & erection of Sectional Double pole for11 KV line on
11 M long ST Pole with fixing necessary clamp & other
accessories like 1 No. top channel 100x50 mm- 2.24 m 01 No
Guarding Angle fabrication of cross bracing. Its grounting in
ration 1:4:8, plinthing 300 mm above ground level. Painting of
pole with one coat or red oxide two coats ot enamel paint ISI
mark & earthing Support.
No. 0
9
Eraction of single stud pole support one ST Pole 11 M long with
fixing of necessary clamps and other accessories required for
rerection
No. 0

9. 10
Stringing and sagging of 3 Phase 33 KV line on ACSR Dog
conductor as per RESSPO Norms.
Ckt. K.M 5
11 stringing and sagging of two nos. Earth/GI wire with
caddieguarding of above 11 kV line as per RESSPO Norms
RMT 1000
12 nozeling and grouting of stay set (All the civil material and stay
set will be arranged by the contractor)
No. 82
13 Laying of 11 KV 3x185 sq.mm. cable by digging ot ternch of size
900 mtr. Deep 500 mm wide as per ISS including providing brick,
sand slab as required at site as per RESSPO Norms
0
i
Laying of 11 KV 3x185 sq.mm. cable pacca metallic road.
Mtr 0
ii Single cable laying in M.S. Pipe size 150 mm dia. Mtr 0
iii For Railway/river/channel/road/drain crossing in MS pipe by
drilling single circuit. ( All the material required for laying will be
supplied by the cotractor except 11 KV XLPE cable)
Mtr 0
iv Laying of single circuit 11 KV 3x185 sq.mm XLPE cable by drilling
method with drilling machine approx 1.5 M to 2.00 M Deep.
Mtr 0
14 Fixing of H.S type cable jointing kits ST/Th end termiantion size
11 KV 3x185 sq.mm.
No. 0
15 Providing and fixing of eatrh rod per norms No. 77
Total Amounts Rs.
Note:-All Centralized Materials to be supplied by Department.
Any other material, filtting i.e. all connections, PG Clamps, gun fitting etc.accessories, equipemtn, apparatus which
might not have been mentioned in the bid document but which are used and necessary for completion of the
work as per RESSPO Norms/relevant ISS shall be arranged by the contractor. All T&P and labour required for
successful completion of work shall be supplied by the contractor.
Date :
Signature of contractor with seal
Place :