LTi Pel it´s a multilayer material that contents special luminescent ink, scattered on a conductive plastic material. When an alternate current is applied, the Pel sheet (electroluninous paper) emits an attractive cold light. Characteristics - Very Thin Pel 0,35mm thickness - Low consume current 1mA/cm2 - Lighting color: White - Easiness and accuracy for printing on lighting area - Inverter of voltage and frecuency 110Volt AC (consult for 220 Volt AC and 12VDC) - Can be cut with scissors and cutter, and can be reconneted the parts - Possibility of sequential or programmed effect Application - Backlighting for LCDs, picture frame ilumination, poster publicity, decoration in floor, roof for bars, night clubs - Sing making, POP (point of purchase application) - Cars and Bus with magnet sheet Measure 15"x 23" 42x60cm (can be cutted and used in pieces) Kit standard panel 42x60cm for source power 110VAC / 220VAC U$140 FOB descount in quantity. View attached related information Videos: Pel in gartments Uruguay 2005 http://www.vimeo.com/619727 Luminous interactive paint Mexico 2007 http://www.vimeo.com/619699

1. LTi Pel (ELECTRO LUMINESCENT PAPER)
-The 220V inverter included in the offer is to use TIPS
with the electroluminescent size panel we send
together. Weld their point of connection the minor possible
-If the electroluminescent panel is cut, you can moment in order not to damage the silver ink
use the 220V inverter connected with all the cut contacts.
parts at the same time, represent 2400 cm2 As all electroluminescent phosphors absorb
(not in separated way, because it may burns) atmospheric moisture it is essential to adequately
-We included a sequencer too, you can cut the seal all possible entry points to prevent premature
pieces from 30cm squared to 100cm squared for failure of the product. Use vinyl tape and thermo
each channel, maximum 5 channels. encapsulate foils.
1-Bending Pel 2-Cooper tape 3-Bus application A 4-Bus application B
4- Tin soldering 5- Tin detail 6- Connector solder 7- Solder protect
9- Inverter
8- Inverter connection 10- Check work 11- Power on
CAUTION
-Do not connect to AC if there is no electro-
luminescent panel connected to the inverter.
-Output inverter: 100VAC 400Hz.
-Avoid bending the EL material too sharply.
-The phosphors may crack resulting in dark
lines and spots on the illuminated surface.
-Wire up your circuit as shown, taking care to
avoid short circuits and insulate all AC wiring
to prevent electric shock hazard.
-The lamp doesn´t have any polarity, it acts as a
condenser.
© Pel LTinews.com

2. LTi Pel INVERTER 5 channel sequencer with patterns
1-Pel front 2- Pel rear 3- Cut in parts 4- Accesories
4- Bus application 5- Tin soldering 6- Connector solder 7- Solder protect
8- Sequencer 9- Inverter connector 10- Check work 11- Power on
The 1st.and 7th. connector wires are the
common output, the remaining 5 wires are the
individual channels. Can be weld a pair of wires
between a channel and the common output.
TIPS
-The Pel can be cut by scissors or cutter.
-Sand smoothly the cut borders.
-Leave connection borders always, the cutting
without silver borders can’t be reconnected.
-Weld the wires on the self-adhesive cooper in
the less possible time, do not apply too much
heat to the silver Bus.
The lamp doesn’t have any polarity, if the
common wire is used in many cuts, verify that it
is not joining to the common in its circuit.
CAUTION:
If the inverter is working without the Pel, or if a
short circuit is made by using the common pin,
it would make an irreversible damage. Verify
with the multimetro the connections before
feeding it. Protect the back Pel with vinyl or
insulating adhesive tape.
© Pel LTinews.com