1. ENGR. JEROME A. LANTOT
Registered Mechanical Engineer
Saudi Counsel of Engineers member
With valid K.S.A driver’s license.
Age: 30 Years old
Address: Block 10 Lot 15 Midori Plains Subdivision Brgy. Tungkop, Minglanilla, Cebu Phils.
e- Mail address: jeromelantot@yahoo.com Skype: jeromelantot
Cell No. 09185478092 (Phil.) / 0548541185(K.S.A)
Applied Position: Mechanical Engineer (Construction/QAQC)
CAREER OBJECTIVE:
To obtain a position where my knowledge in the highly demanding field of mechanical engineering as well as
my communication skill along with my desire for growth can be utilized to their maximum potential.
WORK EXPERIENCES: Construction Engineer: 4.66 Yrs.
QAQC/Office Engineer: 3.5 Yrs.
I. Saudi Services for ElectroMechanic Works Company, SSEM
Almathe’r Street Al Rashid Tower 6th Flr. Riyadh Saudi Arabia
www.ssem.com.sa
Position: Mechanical Engineer
Duration: May 2012 – Present (4.5 yrs.)
• Project Assignments
Project Name : Rafha Power Plant #2 Extension 1 GT5 (77 MW Gas Turbine by Siemens AG)
Client : Saudi Electricity Company
Job Description : QA/QC Mechanical Engineer
Responsibilities :
GTG Area: (PowerHouse)
1. Material inspection &management for all GTG & auxiliaries (Siemens) equipment & materials.
2. Coordinate with Siemens erection supervisor, erection engineers & client regarding
implementation of field quality plans, ITP, protocols & field erection documentation (Test
Protocols/ECC/CCC/Site Observation Reports/Damage Reports) etc.
3. Raise RFIW and RFIM to Siemens TFA/SEC clients.
4. Attend daily/weekly progress meeting with Siemens TFA & Clients.
BOP Area: -PIPING
1. Material Inspection of Supplied materials such as Flange, Fittings, Pipes, Pumps, HVAC,
FireFighting, Tanks etc.
2. Coordinate with the Client Consulting Engineers for various inspection of the plant for materials,
erection & commissioning.
3. Coordinate with construction engineers establishing correct specifications, standard and practices.
4. Inspect & Monitor Welding, Fabrication & NDT for piping.
2. 5. Raise RFI’s for materials & erection.
6. Coordinating & witnessing third party NDT activities for piping & crude oil tank.
7. Prepares Turn over Documents like ECC, CCC, Red Mark Ups & As built drawings for submittal to
Consulting Engineers/Client.
Project Name : Rafha Power Plant #2 GT3 & GT4 (77 MW Gas Turbines by Siemens)
Client : Saudi Electricity Company
Job Description : Site Mechanical Engineer
Responsibilities :
BOP Area: -PIPING
1. Sand Blasting/Coating of CS piping up to 12 inch in diameter.
2. Erection of piping supports. (H-beam/Sleeper/Prefab/Trench Type)
3. Erection of CS/SS/Galv piping. (Fuel oil, Compressed air, Instrument air, Firefighting)
4. Erection of pumps. (GEA unloading, forwarding, transfer pumps)
5. Pre-commissioning activities such as Hydrotest, Pneumatic/Leak Test, Flushing, and Air Blowing.
6. Coordinate with testing engineer for commissioning of fuel pumps.
7. Coordinate with operation team until final handing over of the plant.
Project Name : Salboukh Water Supply to Riyadh
Client : National Water Company (NWC)
Job Description :Site Mechanical Engineer
1.Incharged in installation and alignment of Water Treatment Facilities ( Container Van Type).
2. Installation of interconnection piping between five WTP containers, stainless and CPVC .
3. In charged of fabrication and erection of Glass Lined Steel (GLS) tanks under supervision of the
vendor representative.
II. A.D. Gothong Manufacturing Corporation
Mandaue City Cebu,Philippines
Position: Site Mechanical Engineer
Duration: Sep 7, 2011 - Apr 3, 2012 (7 months)
1. Material take-off activities and BOQ.
2. Supervised erection of piping, pumps, heat exhangers , tanks etc.
3. Line checking activities of piping based on piping and instrumentation diagram (P&ID).
4. Pre-commissioning & Commissioning activities. (Hydrotest/pneumatic test/coordination with
NDT contractor)
III. Metaphil International Incorporated
Mandaue City, Cebu Philippines
Position: QA/QC Mechanical Inspector-Piping
Duration: Mar 4, 2011 - Sep 1, 2011 (6 months)
1. Implement quality control standards as per client’s specifications and international standards.
2. Material inspection according to data sheets and specifications.
3. Performs inspection during construction and fabrication such as
visual and dimensional prior to fit-up and full welding.
4. Witness and conduct Non Destructive Examination (NDT)
a) Liquid Penetration Test (LPT)
b.) Hydro testing & Pneumatic test on piping.
5. Supervise welding works to maintain good welding quality.
6. Coordinate with owner’s representative for inspection, prepares Test and Inspection report.
IV. Kharafi National LLC.
Al Wathba, Abu Dhabi, UAE
Position: Piping Foreman
Duration: Mar 10, 2010 - Mar 1, 2011 (1 year)
3. 1. Installation of pipes, and pipe fittings based on P&ID and isometric plans.
2. Pre-Commissioning of Sedimentation tanks: Testing of lubrication system, boogie alignment
checkup and alignment of other mechanical components.
3. Hydro testing procedures of pipelines.
V. Asian Appraisal Company Incorporated
Cebu Business Park, Cebu City, Philippines
Position: Mechanical Appraiser
Duration: Oct 5, 2008 - Oct 7, 2009 (1 yrs.)
1. Site surveying/inspection general plant equipment, power feed wiring, piping, laboratory
equipment and office equipment.
2. Using standard forms inventory, price, estimate normal and remaining life, and apply observed
depreciation in normal time.
3. Valuation of vessels, machineries, equipment, vehicles, land, buildings and other properties for
their fair market and fair rental value.
4. Review field inventory notes on machinery classification, analyzing final results for completeness
and ensuring all notes are assembled properly for turning over to office processing department.
VI. Cebu Private Power Corporation
Ermita Cebu City Philippines
Position: Trainee
Duration: Jan 4, 2008 - Mar 4, 2008 (0.2 yrs)
1. Preventive maintenance of ten units 7MW diesel engines.
2. Assigned in control room operation as operator.
3. Assigned in engine room operation as operator.
EDUCATIONAL BACKGROUND:
Highest Education: B.S.Degree in Mechanical Engineering
University of Cebu, 2003-2008
Vocational Courses: AutoCAD Drafting
TESDA – Cebu, 2007
High school: Saint Michael School
Argao Cebu Phil., 1999-2003
LICENSES & CERTIFICATION:
Registered Mechanical Engineer Professional Regulatory Commission of the Philippines
License No. (By request), www.prc.gov.ph
Saudi Counsel of Engineers Membership # (By request)
http://www.saudieng.sa/pages/validation.aspx
SKILLS:
1. AutoCAD
2. Microsoft Excel
3. Microsoft Word
4. Welding (SMAW)