Quick overview of Panoura 18S assembly process.

1. Panoura 18S
Three Box Packaging Assembly Quick Guide

2. ImageWorks Proprietary – Confidential Information
These instructions serve as supplemental assembly guidance of
the Panoura. They are not meant to replace the installation
manual, but rather serve to complement it.
If there are any questions, please do not hesitate to contact us
914-592-6100
5/15/2016
2
Summary

3. ImageWorks Proprietary – Confidential Information
1. Packaging Contents
2. Install Post
3. Hang C-Arm
4. Attach Chinrest
5. Attach Head Support
6. Insert Side Covers
7. Insert Center Panel and Mirrors
5/15/2016
3
Agenda

4. ImageWorks Proprietary – Confidential Information
Basic Pan arrives in three boxes containing:
1. Post
2. C-Arm Assembly, Sensor and Components
3. Accessories
5/15/2016
4
1. Package Contents

5. ImageWorks Proprietary – Confidential Information
5/15/2016
5
• Unbox and install the post
• Fasten post to the ground following installation
manual (picture below with a base stand).
2. Install Post

6. ImageWorks Proprietary – Confidential Information
5/15/2016
6
Remove box from C-Arm package by removing 4 screws
attaching box to skid
3. Hang C-Arm

7. ImageWorks Proprietary – Confidential Information
5/15/2016
7
Remove sensor
package
Remove top cover from
c-arm by removing 4
screws.
3. Hang C-Arm

8. ImageWorks Proprietary – Confidential Information
5/15/2016
8
Move C-Arm assembly
into position in front of
post
Remove bolts from c-
arm chassis bracket
3. Hang C-Arm

9. ImageWorks Proprietary – Confidential Information
5/15/2016
9
WARNING: Bolts must be fully removed from
chassis to prevent damage upon installation
Remove bolts that fix C-Arm assembly to wooden frame
3. Hang C-Arm

10. ImageWorks Proprietary – Confidential Information
5/15/2016
10
WARNING:
Damage can occur if
install is done
without moving
drive unit
Move driving unit by rotating coupling of x-axis motor by hand
so as not to hit slide body with rotating arm during assembly
3. Hang C-Arm

11. ImageWorks Proprietary – Confidential Information
5/15/2016
11
WARNING: Make sure no cables get caught between post
bracket and C-arm assembly
Lift up C-arm assembly and place large hook over mating
bracket. Two pins and two tabs fit through mating holes
(see next slide)
3. Hang C-Arm

12. ImageWorks Proprietary – Confidential Information
5/15/2016
12
There are two pins and two tabs on the bracket that fit
through mating holes in the C-arm assembly.
Pin into
slot (x2)
Tab into
slot (x2)
3. Hang C-Arm

13. ImageWorks Proprietary – Confidential Information
5/15/2016
13
• Place and tighten four bolts to fasten C-Arm to Post
• Pull cable assembly up through hole in C-Arm Chassis, and
make 7 wiring connections (for Pan Unit without ceph)
3. Hang C-Arm

14. ImageWorks Proprietary – Confidential Information
5/15/2016
14
Run Ethernet cable down
through same hole. Make
sure cable is above the
support tray (otherwise front
panel will not fit).
Remove panel box on rear
of unit and connect Ethernet
to port in box. Reattach
panel box.
3. Hang C-Arm

15. ImageWorks Proprietary – Confidential Information
5/15/2016
15
Check leveling of the unit following 2.2.4 Leveling in the
Installation Manual
Note: In the case of Ceph unit, check the level after
installation of the unit as following “2.9 Cephalometric Unit
Mounting” in the Installation Manual
3. Hang C-Arm

16. ImageWorks Proprietary – Confidential Information
5/15/2016
16
Attach chinrest assembly
over 2 pins and screw to
chinrest bracket on post (4
screws).
To attach chinrest
assembly, remove 4 bolts
from chinrest bracket.
4. Attach Chinrest

17. ImageWorks Proprietary – Confidential Information
5/15/2016
17
Fasten the under panel of the
chinrest with the four screws.
Run cables over the chinrest
assembly as shown and
make connection of cable on
the right side. Fix wiring
using banding connectors on
chinrest assembly.
4. Attach Chinrest

18. ImageWorks Proprietary – Confidential Information
5/15/2016
18
Remove screws on rear left and right of chinrest assembly
cover. Place cover and insert screws.
4. Attach Chinrest

19. ImageWorks Proprietary – Confidential Information
5/15/2016
19
Insert and attach underside
cover with 5 screws and
connect connector
4. Attach Head Support
Remove cap4 screws on the
head support fastening
bracket

20. ImageWorks Proprietary – Confidential Information
5/15/2016
20
Connect the connector on
the head support unit to the
connector on the driving
part
4. Attach Head Support

21. ImageWorks Proprietary – Confidential Information
5/15/2016
21
Refer to the figure. Put the connector in the connector holder
on the head support disc and fasten the head support unit
using the 4 screws
NOTE: When mounting the head support unit, make sure that
the connector is placed in the connector holder on the head
support disc. Beware that the harness is not caught between
when the screws are fastened
4. Attach Head Support

22. ImageWorks Proprietary – Confidential Information
5/15/2016
22
Remove left side cover from packaging
5. Insert Side Covers
Make cabling connection to inside of keypad (K1, K3-K7, K2
for Ceph unit)

23. ImageWorks Proprietary – Confidential Information
5/15/2016
23
Fasten left side and right side panels
5. Insert Side Covers

24. ImageWorks Proprietary – Confidential Information
5/15/2016
24
Insert center panel and mirror
Mount eye-ear beam lever
6. Insert Center Panel and Mirror

25. ImageWorks Proprietary – Confidential Information
5/15/2016
25
Continue with standard installation procedure from
installation manual