2. S.No Name of the student Department
Email ID
Contact
Number
1 Kavinraj.K EEE 19tuee048@skct.edu.in 9360718839
2 Kiran.K EEE 19tuee052@skct.edu.in 8610548505
3
Mohamed
Arshath.A.M
EEE 19tuee059@skct.edu.in 9360183839
4 Santhiya.V EEE 21tuee705@skct.edu.in 7548895931
5 Priyadharshini.G EEE 20tuee113@skct.edu.in 9345227562
6 Thendraldevi.M EEE 20tuee137@skct.edu.in 8870938003
IOT Based Child Rescue System
from Open Borewell
Guided By : Manimegalai.V
3. For past few years, there have been several an accident of
children falling into an abandon bore-well which is left
uncovered and get trapped.
There is a risk that children or animals fall down into the bore
well.
The depth and the diameter of the bore-well is the main
obstacle to rescue the child safely.
These results in the major problems and affects the total area
surrounded which happens due to lackness of consciousness of
labours So we have planned to do it using hardware automation
lets get into our idea
In such accidents normal rescue operations are very complicated
because the process is time consuming, requires huge man-
power etc.
Idea / Approach Details
5. The aim of this project is to provide a better and reliable solution
for this problem.
This rescue system uses the high-tech electronics automatic
system the block diagram of the hardware set up.
Here IR1 infrared sensor is placed near to the open bore well.
IR2 and IR3 infrared sensors are connected inside the bore-well.
If any movement is detected near to the bore well it will detect
by the IR1 sensor and send information to the Arduino Uno
controller.
Controller will send the alert message through GSM module to
the authorized person and display the same message on the LCD
display.
Proposed System
6. Here only we can save the life of the victim before falling down
into the bore-well.
Then also if child felled down into the bore-well then IR2 and IR3
sensor will sense the motion in-side the bore well and activate
the dc motor driver.
It gives long alarm. This DC motor driver controlling the two
motors namely M1 and M2.
M1 motor is used to rotate the vertical plate into the horizontal
position to catch the child, And stop child further going into the
dept.
Motor M2 is used to pull up the rotated plate along with the
child.
After successfully saving the child reset button is provided to
bring the system into the original position.
This system requires the 5-volt AC voltage supply.
Proposed System
10. Arduino IDE : Arduino Integrated Developing Enivornment is
used create a program with embedded C for Arduino uno.
Motor : It is a rotary actulator used on linear and angular
position and for specific velocity and acceleration.
IR Sensor : It is used for detecting human motion near bore well
Technology Stack
11. The IOT setup connected to the bore well detected the test object
(stuff doll) felt into the bore well and message is sent using the IOT
to the number which is given in the code.
By using the pickup arm the test object (stuff doll) is taken out
from the bore well safely. It used to rescue the child fast and it is a
easy way to rescue the child or animal.
By using this method this result in the prevention without any big
difficulties.
Through our idea we will be aware of the spot surrounded
through out so there is no need of any third party surveillance or
extra peoples to monitor it.
Justification of Proposed Systems
12. The setup has 360 degree motion surveilance which provides
indications.
We have placed a buzzer to indicate when someone gets into the
radius of 15m.
We have planned our idea as a kit so it will portable to any places
which will be more easy.
Indication will be sent to the people if anyone enters into radius of
5m incase they didn’t hear any buzzer or not aware of it.
Major accidents wont be happen by privilege of using motors
through which surrounds the person.
Relevant Information
