Coagulation

1. ECL 105

2. Main points
• Specifications
• Device presentation
• Main Instrument
• Installation
• Settings
• Maintanance
• Troubleshooting
• Spare parts

3. Specifications
General
• 216 x 205 x 75 mm ; ~1 kg
• 17-32°C ; 80% Relative Humidity
• 100-240 VAC and 50/60 Hz; 45W; 150VA
• High capacity
• Calibrations -up to 6 calibration levels
• QC - 12 different control names

4. Specifications
Tests principles
• Clotting (scattered light at 640nm)
• Immuno-turbidimetric (turbidimetry at
800nm)

5. Specifications
Parameters
• PT, APTT, Fibrinogen, TT
• Factors – Extrinsic, Intrinsic
• D-Dimer
• Others (Protein S, Lupus DRVV)

6. Device presentation
• Front side

7. Device presentation
• Left side

8. Device presentation
• Rear view

9. Main Instrument
• Covers
• Main Board
• Printer
• RFID module
• Display
• Power adapter

10. Main Instrument
Main Board
IR LED
RED
LED

11. Installation
• Table - 220 mm (W) x 210 mm (D)
• 100 mm back space – ventilation, cables
• Temperature 17-32°C, humidity max 80%
• avoid direct sunlight, dust . . . .
Put the supply tightly to instrumet
Plug the adaptor to wall socket
Instal paper roll and close lid

12. Settings
User level
• Remove all QC data
• Remove all results
• Set to factory data – ECL will
preserve stored quantities
Service level
• Usage all of user methods
• Edit device properties
• Test peripheries

13. Settings
MEASURE
• Measure AD vaules
• Change usable LEDs
• Check and set values

14. Settings
USB
• Test USB communication
• Mass storage test – r/w to USB
• USB keyboard test – w witk kb
• USB B test – virtual COM port
PRINTER
• Test motor and printer
• Printer temt – temperature of
head

15. Settings
ETHERNET
• Detects and displays IP addres
SERIAL
• Test RS232 communication

16. Settings
RFID
• Test of reader
OTHERS
• Test functions of reader

17. Maintanance
Daily Beginning of day
• Check any damage, electrical and LIS connections are secure
• Swipe dust and any other liquids from surface wet and dry towel
• turn ON and wait for temperature 37+/-0.5°C
End of day
• Turn OFF
• Remove all cuvets and reagent tubes
• Clean surface
Note: For decontamination of the surface use a 1+1 solution of alcohol and water.
Note: Do not use strong bleach that could demage cover plastics and other.

18. Troubleshooting
• No back light
• Blank LCD / faulty display
• Touch screen error
• Printer error
• Time and data lost
• RFID error
• LED / Detector error
• Power error

19. No back light
Measeure voltage 15 – 22V DC
• OK – replace LCD
• NOT OK – replace main board

20. Blank LCD / faulty display
Check connection
• NOT OK – replace LCD

21. Touch screen error
Check connection
• NOT OK – replace LCD

22. Printer error
Printer doesn‘t print at all
• Printer test
• Check connection– replace printer

23. Time and data lost
Data are not stored
• Replace CR2032 battery

24. RFID error
Check the tag in menu
• Check connection
• NOT OK – replace RFID panel

25. LED / Detector error
Check If LEDS and detector are OK
• Check visually
• Check by controls
• NOT OK - replace LED
• Measure and calibrate
temperature
Incubator test
Measurement test

26. Power error
• Measure output of adapter
• If mechanical demage, replace
switch

27. Spare parts
Reg. číslo Název
50004601 ECL 412/ECL 105 PRINTER
50004602 ECL 412/ECL 105 RFID MODULE
50004604 ECL 412/ECL 105 POWER SUPPLY
50004605 ECL 105 PCB+INCUBATORS+MEASURING CHANNELS ASSEMBLY
50004606 ECL 105 DISPLAY
50004607 ECL 105 INSTRUMENT COVERS
50004642 ECL 105 PRINTER COVER