Your SlideShare is downloading. ×
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
How to configure i pv6 services in the fttb c (no hgws) scenario
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

How to configure i pv6 services in the fttb c (no hgws) scenario

189

Published on

Leading Huawei networking products distributor-Huanetwork.com …

Leading Huawei networking products distributor-Huanetwork.com
How to Configure IPv6 Services in the FTTB C (No HGWs) Scenario

Published in: Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
189
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
3
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. How to Configure IPv6 Services in the FTTB/C (No HGWs) Scenario This section describes the methods for configuring IPv6 services in the FTTB/C (No HGWs) scenario. Application Scenarios The FTTB/C networking(no HGW) supports the access of IPv6 HSI services. Generally, no IPTV services will be deployed when there is no HGW. As shown in Figure 1, the Huawei ONU, which is installed in a corridor or street optical distribution box, transmits services to users through category-5 cables (LAN access) or twisted pairs (xDSL access). The OLT and ONU work with upper-layer devices to support Huawei DS+NAT+PPPoE/DS+NAT+IPoE HSI IPv6 solutions. 1 For voice services: The ONU with a built-in voice module can directly provide VoIP services for users. The ONU processes VoIP services using the IPv4 protocol instead of the IPv6 protocol. 2 For Internet access services: Users connect to the ONU through category-5 cables (LAN access) or the modem and twisted pairs (xDSL access). The PC and BRAS support the IPv4/IPv6 DS and can be connected in the PPPoE or IPoE mode. The OLT and ONU implement Layer 2 forwarding, irrespective of whether the access service is IPv4 or IPv6. Service configurations for IPv4 and IPv6 are the same. Only the ACL, anti-IP spoofing, and DHCP option configurations for IPv4 and IPv6 are different. Figure 1 FTTB/C (no HGW) networking Procedure Step 1 Configure GPON ONU profiles. 1. Configure a DBA profile. huawei(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 1
  • 2. 20480 2. Configure an ONU line profile. huawei(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c) huawei(config-gpon-lineprofile-10)#tcont 4 dba-profile-name fttb_dba huawei(config-gpon-lineprofile-10)#gem add 11 eth tcont 4 cascade on huawei(config-gpon-lineprofile-10)#gem add 12 eth tcont 4 cascade on huawei(config-gpon-lineprofile-10)#gem add 13 eth tcont 4 cascade on huawei(config-gpon-lineprofile-10)#gem mapping 11 0 vlan 8 huawei(config-gpon-lineprofile-10)#gem mapping 12 1 vlan 1001 huawei(config-gpon-lineprofile-10)#gem mapping 13 2 vlan 200 huawei(config-gpon-lineprofile-10)#commit huawei(config-gpon-lineprofile-10)#quit 3. (Optional) Add an alarm profile. In this example, the default alarm profile is used and therefore the configuration of the alarm profile is not required. Step 2 Add an ONU to an OLT. Assume that the ID of GPON port 0/2/1 is 1, SN is 32303131B39FD641, management mode is SNMP, and the bound line profile is fttb(c). Connect the ONU to such a GPON port through the optical splitter. There are two modes to add an ONT: add an ONT offline and confirm an automatically discovered ONU. 1 Add an ONU offline. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c) 2 Confirm an automatically discovered ONU. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#port 1 ont-auto-find enable huawei(config-if-gpon-0/2)#display ont autofind 1 huawei(config-if-gpon-0/2)#ont confirm 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c) 3 (Optional) Bind the alarm profile to the ONU. In this example, default alarm profile 1 is used and therefore the configuration of the alarm profile is not required. Step 3 Check the ONU status. 2
  • 3. After an ONU is added, run the display ont info command to query the current status of the ONU. Ensure that Config flag of the ONU is active, Run State is online, and Config state is normal. huawei(config-if-gpon-0/2)#display ont info 1 1 --------------------------------------------------------------------- F/S/P : 0/2/1 ONT-ID : 1 Control flag : active //The ONU is activated. Run state : online //The ONU is online. Config state : normal //The ONU configurations are recovered normally. ...//The rest of the response information is not provided here. huawei(config-if-gpon-0/2)#quit Step 4 Configure the inband management VLAN and IP address of the OLT. huawei(config)#vlan 8 smart huawei(config)#vlan priority 8 6 huawei(config)#interface vlanif 8 huawei(config-if-vlanif8)#ip address 192.168.50.1 24 huawei(config-if-vlanif8)#quit Step 5 Configure the inband management VLAN and IP address of the ONU. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address 192.168.50.2 mask 255.255.255.0 gateway 192.168.50.254 vlan 8 huawei(config-if-gpon-0/2)#quit Step 6 Configure an inband management service port. huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6 Step 7 Confirm that the management channel between the OLT and the ONU is available. l On the OLT, run the ping 192.168.50.2 command to check the connectivity between the OLT and the ONU. The ICMP ECHO-REPLY packet from the ONU should be received. l On the OLT, you can remote log in to the ONU to perform the configuration. Step 8 Configure the channel for the Internet access service. huawei(config)#vlan 100 smart huawei(config)#vlan attrib 100 stacking huawei(config)#port vlan 100 0/19 0 3
  • 4. huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 12 multiservice user-vlan 1001 tag-transform translate-and-add inner-vlan 258 rx-cttr 6 tx-cttr 6 Step 9 Configure the channel for the VoIP service. huawei(config)#vlan 200 smart huawei(config)#port vlan 200 0/19 0 huawei(config)#traffic table ip index 9 cir off priority 5 priority-policy localsetting huawei(config)#service-port 201 vlan 200 gpon 0/2/1 ont 1 gemport 13 multiservice user-vlan 200 rx-cttr 9 tx-cttr 9 Step 10 Configure LAG for upstream ports. Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the aggregation group allocates packets based on the source MAC address. The working mode is LACP static aggregation. huawei(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static Step 11 (Optional) When PPPoE is adopted, enable forwarding the packets with PITP tag on the OLT equipment. huawei(config)#pitp permit-forwarding service-port 101 enable Step 12 (Optional) When IPoE is adopted, enable forwarding the packets with DHCP option on the OLT equipment. huawei(config)#dhcp-option82 permit-forwarding service-port 101 enable //For IPv4 packets huawei(config)#dhcpv6-option permit-forwarding port 0/2/1 ontid 1 enable //For IPv6 packets Step 13 Save the configuration data on the Huawei OLT. huawei(config)#save Step 14 Log in to and configure the ONU. You can remote log in to the ONU from the OLT to perform the configuration. By default, the user name is root and the password is mduadmin. NOTE The following steps are configured on the ONU side. Step 15 Configuration the HSI service on the ONU side. NOTE This example creates one service port as an example. Each service port maps a user. When configuring another service port, map the corresponding SVLAN. huawei(config)#vlan 1001-1016 smart huawei(config)#port vlan 1001-1016 0/0 1 4
  • 5. huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local-Setting huawei(config)#service-port 101 vlan 1001 eth 0/3/1 multi-service user-vlan untagged rx-cttr 8 tx-cttr 8 Step 16 (Optional) Configure the PITP function for PPPoE. huawei(config)#raio-mode common pitp-pmode huawei(config)#pitp enable pmode Step 17 (Optional) Configure the DHCP option function for IPoE. huawei(config)#raio-mode common dhcp-option82 //For DHCPv4 packets huawei(config)#dhcp option82 enable //For DHCPv4 packets huawei(config)#raio-mode common dhcpv6-option //For DHCPv6 packets huawei(config)#dhcpv6 option enable //For DHCPv6 packets Step 18 Configure the voice service. huawei(config)#vlan 200 smart huawei(config)#port vlan 200 0/0 1 huawei(config)#interface vlanif 200 huawei(config-if-vlanif200)#ip address 17.10.10.10 24 huawei(config-if-vlanif200)#quit huawei(config)#voip huawei(config-voip)#ip address media 17.10.10.10 17.10.10.1 huawei(config-voip)#ip address signaling 17.10.10.10 huawei(config-voip)#quit huawei(config)#ip route-static 200.200.200.0 24 17.10.10.1 huawei(config)#interface h248 0 Are you sure to add MG interface?(y/n)[n]:y huawei(config-if-h248-0)#if-h248 attribute mgip 17.10.10.10 mgport 2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-port 2944 mg-media-ip1 17.10.10.10 start-negotiate-version 1 huawei(config-if-h248-0)#reset coldstart Are you sure to reset MG interface?(y/n)[n]:y huawei(config-if-h248-0)#quit huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001 huawei(config-esl-user)#mgpstnuser modify 0/3/0 priority cat2 huawei(config-esl-user)#quit huawei(config)#pstnport huawei(config-pstnport)#pstnport attribute batset 0/3/0 0/3/23 reverse-pole-pulse enable huawei(config-pstnport)#quit 5
  • 6. Step 19 Save the configuration on the ONU side. huawei(config)#save ----End More related: Configuration Difference Between IPv6 and IPv4 The configuration of Huawei MA5616 script Basic Layout of OLT MA5600 Multi Service Access Module Operation and Maintenance How to Add and Delete ONT on the OLT Device More Huawei products and Reviews you can visit: http://www.huanetwork.com/blog Huanetwork.com is a world leading Huawei networking products distributor, we wholesale original new Huawei networking equipments, including Huawei switches, Huawei routers, Huaweisymantec security products, Huawei IAD, Huawei SFP and other Huawei networking products. Our customers include telecom operators, Huawei resellers, ISP and system integrators. Right now most of our sales are contributed by regular customers. And in our Huanetwork Lab, we have below products ready for test: • Huawei OLT Optical Line Terminal MA5600T Series • Huawei MDU Multiple Dwelling Unit MA5620 • Huawei ONT Optical Network Terminal HG8245A, HG8245, HG8010H • Huawei DSLAM MA5616 • Huawei AC-DC Power Converter System EPS30-4815AF • Huawei Optical Splitter 1:32 • Huawei X700 Series GE Switch S5700-28C-EI with 10G Uplink Module • Huawei X700 Series Access Layer Switch S2700-9TP-EI-AC • Huawei X300 Series Layer 3 Full Optical DC Switch S3328TP-EI-24S-DC • Huawei SFP, SFP+, XFP Module, GPON B+ C+ Module • Huawei Routers AR1200 Series • Huawei U2000 Network Management System • Huawei eSight Network Management System • Cisco WS-C3560X-24P-L Switch (for compatible test purpose) Now with Huanetwork Lab, customers can do below test: 1. FTTx System Test 2. ADSL2+ System Test 3. Campus LAN/WAN Test 6
  • 7. 4. Optical Transceiver Test 5. Network Management Test 6. Compatible Test 7. Software Upgrade Test 8. Products Test For customers interested in Huanetwork products, please feel free to contact your sales request for test arrangement. Kindly note, Huanetwork Lab is not open to public, it is just available for Huanetwork customers. Huanetwork reserve the right to reject any test/login requirement. Our website: http://www.huanetwork.com Telephone: +852-30501940 Email: sales@huanetwork.com Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong 7

×