Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Cisco CCNA IPV6 Static Configuration

1,288 views

Published on

Cisco CCNA Training/Exam Tips that are helpful for your Certification Exam!
To be Cisco Certified please Check out:
http://asmed.com/information-technology-it/

Published in: Education
  • Be the first to comment

  • Be the first to like this

Cisco CCNA IPV6 Static Configuration

  1. 1. CISCO CCNA IPV6 Static Configuration To watch our Cisco CCNA Video Trainings Please Check out the link below: www.asmed.com/c1 ASM EDUCATIONAL CENTER INC. (ASM) WHERE TRAINING, TECHNOLOGY & SERVICE CONVERGE PHONE: (301) 984-7400 ROCKVILLE,MD
  2. 2. IPV6 Static Configuration
  3. 3. IPV6 Static Configuration Now I will do small Lab: The Goal is that seated at R4 be ableto ping allthe loopback of R10 , in order to do this , we will cover StaticRoute. R4=10.10.10.4 R10=10.10.10.10 connected via LAN link Also I will have IPV6 as follow: r4 f0/0=2001:4444::4/64 r10 f0/0=2001:4444::10/64
  4. 4. IPV6 Static Configuration In here we have R4 and R10 with the following: Here is: R4#Show run interface FastEthernet0/0 ip address 10.10.10.4 255.255.255.0 duplex auto speed auto ipv6 address 2001:4444::4/64
  5. 5. IPV6 Static Configuration Here is R10 with so many loopback address: interface Loopback0 ip address 100.100.100.100 255.255.255.0 ! interface Loopback1 no ip address ipv6 address FEC0:1000::1/128 ! interface Loopback2 no ip address ipv6 address FEC0:1000::2/128 !
  6. 6. IPV6 Static Configuration interface Loopback3 no ip address ipv6 address FEC0:1000::3/128 ! interface Loopback4 no ip address ipv6 address FEC0:1000::4/128 ! interface FastEthernet0/0 ip address 10.10.10.10 255.255.255.0 duplex auto speed auto ipv6 address 2001:4444::10/64
  7. 7. IPV6 Static Configuration Right now when i go to R4#show ipv6 route i do not see the loopback from R10 why? Since i need to run do ipv6 Static Route R4#show ipv6 route IPv6 Routing Table– 3 entries Codes: C – Connected, L – Local, S – Static,R – RIP, B – BGP U – Per-user Staticroute, M – MIPv6 I1 – ISIS L1, I2 – ISIS L2, IA – ISIS interarea, IS – ISIS summary O – OSPF intra,OI – OSPF inter,OE1 – OSPF ext 1, OE2 – OSPF ext 2 ON1 – OSPF NSSA ext 1, ON2 – OSPF NSSA ext 2 D – EIGRP, EX – EIGRP external C 2001:4444::/64 [0/0] via ::,FastEthernet0/0 L 2001:4444::4/128 [0/0] via ::,FastEthernet0/0 L FF00::/8 [0/0] via ::,Null0
  8. 8. IPV6 Static Configuration So remember you need enable unicast-routing Hint: on global Configuration start with IPV6? Here is my configuration on R4# Step 1) Enable Unicast-routing on R4 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ipv R4(config)#ipv6 ? access-list Configure access lists cef Cisco Express Forwarding dhcp Configure Ipv6 DHCP
  9. 9. IPV6 Static Configuration general-prefix Configure a general IPv6 prefix host Configure static hostnames inspect Context-based Access Control Engine local Specify local options nat NAT-PT Configuration commands neighbor Neighbor route Configure static routes router Enable an IPV6 routing process unicast-routing Enable unicast routing R4(config)#ipv6 unicast-routing
  10. 10. IPV6 Static Configuration Step 2) Now I willconfigure Static Route, in here I need to put the destination Network inside my R4 router That is I need to have: ipv6 route FEC0:1000::1/128 2001:4444::10 Destination Network (Next Hop address) We must do above commands for all Loopback address , since the goal is that seated at R4 I should be able to ping all loopback address located on R10 ipv6 route FEC0:1000::2/128 2001:4444::10 ipv6 route FEC0:1000::3/128 2001:4444::10 ipv6 route FEC0:1000::4/128 2001:4444::10
  11. 11. IPV6 Static Configuration Now we will configure it on R4 (using the ? mark) R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ipv6 ? access-list Configure access lists cef Cisco Express Forwarding dhcp Configure Ipv6 DHCP general-prefix Configure a general IPv6 prefix host Configure static hostnames inspect Context-based Access Control Engine local Specify local options nat NAT-PT Configuration commands
  12. 12. IPV6 Static Configuration neighbor Neighbor route Configure static routes router Enable an IPV6 routing process unicast-routing Enable unicast routing R4(config)#ipv6 route ? X:X:X:X::X/<0-128> IPv6 prefix R4(config)#ipv6 route FEC0:1000::1/128 ? Ethernet IEEE 802.3 FastEthernet FastEthernet IEEE 802.3 GigabitEthernet GigabitEthernet IEEE 802.3z Loopback Loopback interface Serial Serial Vlan Catalyst Vlans X:X:X:X::X IPv6 address of next-hop
  13. 13. IPV6 Static Configuration R4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10 ? <1-254> Administrative distance <cr> R4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10 R4(config)# Now I will just use up arrow key and put the rest of loopback network R4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10 R4(config)# R4(config)# R4(config)#ipv6 route FEC0:1000::2/128 2001:4444::10 R4(config)#ipv6 route FEC0:1000::3/128 2001:4444::10 R4(config)#ipv6 route FEC0:1000::4/128 2001:4444::10
  14. 14. IPV6 Static Configuration Here is my show run so far on R4# R4#show run ipv6 unicast-routing ! ! ! ipv6 route FEC0:1000::1/128 2001:4444::10 ipv6 route FEC0:1000::2/128 2001:4444::10 ipv6 route FEC0:1000::3/128 2001:4444::10 ipv6 route FEC0:1000::4/128 2001:4444::10 !
  15. 15. IPV6 Static Configuration Now If I try to ping from R4 to the loopback address of R10 , it will work . R4#ping FEC0:1000::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:1000::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms R4#ping FEC0:1000::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:1000::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 ms R4#ping FEC0:1000::3
  16. 16. IPV6 Static Configuration Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:1000::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms R4#ping FEC0:1000::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:1000::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/1/8 ms But if I had some loopback address on the R4 , then R10 can not ping that loopback address , we can use same concept as above or I Can show you the concept of Default route. I go to R4 and create one Loopback address on R4#
  17. 17. IPV6 Static Configuration R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int loopback 1 R4(config-if)#ipv6 address FEC0:4000::1/128 R4(config-if)# R4(config-if)#int loopback 2 R4(config-if)#ipv6 address FEC0:4000::2/128 R10#
  18. 18. IPV6 Static Configuration Step 3) Hint: remember to enable IPV6 unicast-routing on R10 R10#config t Enter configuration commands, one per line. End with CNTL/Z. R10(config)#ipv R10(config)#ipv6 un R10(config)#ipv6 ? access-list Configure access lists cef Cisco Express Forwarding dhcp Configure Ipv6 DHCP general-prefix Configure a general IPv6 prefix host Configure static hostnames
  19. 19. IPV6 Static Configuration inspect Context-based Access Control Engine local Specify local options nat NAT-PT Configuration commands neighbor Neighbor route Configure static routes router Enable an IPV6 routing process unicast-routing Enable unicast routing R10(config)#ipv6 uni R10(config)#ipv6 unicast-routing R10(config)#
  20. 20. IPV6 Static Configuration Step 4) Now I willdo Default route on R10 and I willuse next hop address R10# ipv6 route ::/0 2001:4444::4 Hint: for default route in Ipv4 we use 0.0.0.0 0.0.0.0 but for Ipv6 we will use ::/0 R10#config t Enter configuration commands, one per line. End with CNTL/Z. R10(config)#ipv R10(config)#ipv6 ? access-list Configure access lists cef Cisco Express Forwarding dhcp Configure Ipv6 DHCP general-prefix Configure a general IPv6 prefix
  21. 21. IPV6 Static Configuration host Configure static hostnames inspect Context-based Access Control Engine local Specify local options nat NAT-PT Configuration commands neighbor Neighbor route Configure static routes router Enable an IPV6 routing process unicast-routing Enable unicast routing R10(config)#ipv6 rout R10(config)#ipv6 route ? X:X:X:X::X/<0-128> IPv6 prefix R10(config)#ipv6 route ::/0 ? Ethernet IEEE 802.3 FastEthernet FastEthernet IEEE 802.3 GigabitEthernet GigabitEthernet IEEE 802.3z Loopback Loopback interface
  22. 22. IPV6 Static Configuration Serial Serial Vlan Catalyst Vlans X:X:X:X::X IPv6 address of next-hop R10(config)#ipv6 route ::/0 2001:4444::4 R10(config)# Here is my Show run on R10# ipv6 unicast-routing ipv6 route ::/0 2001:4444::4 Now seated on R10 I should be able to ping the Loopback address of R4 R10#ping FEC0:4000::1
  23. 23. IPV6 Static Configuration Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:4000::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 ms R10#ping FEC0:4000::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FEC0:4000::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms R10#
  24. 24. IPV6 Static Configuration Here is show Ipv6 route on R4 and R10 R4#show ipv6 route IPv6 Routing Table – 9 entries Codes: C – Connected, L – Local, S – Static, R – RIP, B – BGP U – Per-user Static route, M – MIPv6 I1 – ISIS L1, I2 – ISIS L2, IA – ISIS interarea, IS – ISIS summary O – OSPF intra, OI – OSPF inter, OE1 – OSPF ext 1, OE2 – OSPF ext 2 ON1 – OSPF NSSA ext 1, ON2 – OSPF NSSA ext 2 D – EIGRP, EX – EIGRP external C 2001:4444::/64 [0/0] via ::, FastEthernet0/0 L 2001:4444::4/128 [0/0] via ::, FastEthernet0/0
  25. 25. IPV6 Static Configuration S FEC0:1000::1/128 [1/0] via 2001:4444::10 S FEC0:1000::2/128 [1/0] via 2001:4444::10 S FEC0:1000::3/128 [1/0] via 2001:4444::10 S FEC0:1000::4/128 [1/0] via 2001:4444::10 C FEC0:4000::1/128 [0/0] via ::, Loopback1 C FEC0:4000::2/128 [0/0] via ::, Loopback2 L FF00::/8 [0/0] via ::, Null0
  26. 26. IPV6 Static Configuration Here is show ipv6 route for R10 R10#show ipv6 route IPv6 Routing Table – 8 entries Codes: C – Connected, L – Local, S – Static, R – RIP, B – BGP U – Per-user Static route, M – MIPv6 I1 – ISIS L1, I2 – ISIS L2, IA – ISIS interarea, IS – ISIS summary O – OSPF intra, OI – OSPF inter, OE1 – OSPF ext 1, OE2 – OSPF ext 2 ON1 – OSPF NSSA ext 1, ON2 – OSPF NSSA ext 2 D – EIGRP, EX – EIGRP external S ::/0 [1/0] via 2001:4444::4
  27. 27. IPV6 Static Configuration C 2001:4444::/64 [0/0] via ::, FastEthernet0/0 L 2001:4444::10/128 [0/0] via ::, FastEthernet0/0 C FEC0:1000::1/128 [0/0] via ::, Loopback1 C FEC0:1000::2/128 [0/0] via ::, Loopback2 C FEC0:1000::3/128 [0/0] via ::, Loopback3 C FEC0:1000::4/128 [0/0] via ::, Loopback4 L FF00::/8 [0/0] via ::, Null0
  28. 28. IPV6 Static Configuration Here is summary on R4 and R10 show run: R4#show run interface Loopback0 ip address 4.4.4.4 255.255.255.0 ! interface Loopback1 no ip address ipv6 address FEC0:4000::1/128 ! interface Loopback2 no ip address ipv6 address FEC0:4000::2/128 !
  29. 29. IPV6 Static Configuration interface FastEthernet0/0 ip address 10.10.10.4 255.255.255.0 duplex auto speed auto ipv6 address 2001:4444::4/64 ! ipv6 route FEC0:1000::1/128 2001:4444::10 ipv6 route FEC0:1000::2/128 2001:4444::10 ipv6 route FEC0:1000::3/128 2001:4444::10 ipv6 route FEC0:1000::4/128 2001:4444::10 R10#show run Building configuration… ipv6 unicast-routing !
  30. 30. IPV6 Static Configuration interface Loopback1 no ip address ipv6 address FEC0:1000::1/128 ! interface Loopback2 no ip address ipv6 address FEC0:1000::2/128 ! interface Loopback3 no ip address ipv6 address FEC0:1000::3/128 !
  31. 31. IPV6 Static Configuration interface Loopback4 no ip address ipv6 address FEC0:1000::4/128 ! interface FastEthernet0/0 ip address 10.10.10.10 255.255.255.0 duplex auto speed auto ipv6 address 2001:4444::10/64 ! ! ipv6 route ::/0 2001:4444::4 !
  32. 32. ASM EDUCATIONAL CENTER INC. (ASM) WHERE TRAINING, TECHNOLOGY & SERVICE CONVERGE PHONE: (301) 984-7400 ROCKVILLE,MD To watch our Cisco CCNA Video Trainings Please Check out the link below: www.asmed.com/c1

×