http://www.spooky2-mall.com. Many users were confused why their remote is not lit, or why does it stop working.So this article wil explain that how does spooky remote light.
2. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Many users were confused why their remote is not lit, or why does it stop
working, etc.
Seemingly baffling LED behavior ranging from only one LED lighting to neither
of them working was reported.
But to those with "The Knowledge," this was all normal, and to be expected.
The truth is that the LEDs are far more useful than they appear, and once you
understand how they work, you'll be able to judge at a glance a lot more of
what's going on in your generator.
3. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Three things control how the LEDs respond to the signal – frequency, waveform,
and amplitude. I don't own an oscilloscope, so I've constructed the graphics in
Spooky2 by using Wave Cycle Multipliers to give you an indication of what's going
on. First, let's look at frequency:
4. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Remote & frequency
This is a 1Hz square wave. It completes one positive-to-negative cycle every
second.
A: Signal is positive for half a second, so the left LED lights for half a
second.
B: Signal immediately drops through 0 to negative.
C: Signal is negative for half a second, so the right LED lights for half a
second.
The LEDs turn on and off very slowly, and are never both lit at the same time.
5. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Now here's a 32Hz square wave - it completes 32 positive-to-negative cycles
every second. Count the peaks – there are 32.
With this frequency, the entire A-B-C cycle described above takes place 32
times every second.
6. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
This means that for every one of those 32 cycles, the signal is positive for
1/64th of a second, so the left LED is lit for 1/64th of a second.
The signal then goes negative for 1/64th of a second, so the right LED lights
for 1/64th of a second.
Now the LEDs are both flashing very quickly. Nevertheless, it’s always the
case that only one of them is lit at a time.
Note that if you use a Wave Cycle Multiplier of 12, the frequency sent to the
5M is divided by 12. Now let's move it up a notch.
7. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Here's a 256Hz square wave. Please note that a real one you'd see on an
oscilloscope doesn't look exactly like this – what we're running up against here are
the resolution limits of computer screens. Nevertheless, 256 cycles in a single
second moves the peaks of each one so close to one another that the PC screen
cannot show any degree of separation between them.
Now, the original A-B-C positive-to-negative cycle happens 256 times every
second.
8. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
And for each of those 256 cycles, the signal is positive for 1/512th of a second, so
the left LED lights for 1/512th of second.
The cycle then goes negative for 1/512th of a second, so the right LED is lit for
1/512th of a second.
Now each LED will appear to be constantly lit, at equal brightness. However, it’s
not possible for each LED to be lit at the same time, because the signal can never
be both positive and negative at the same time, so what you’re seeing is an
illusion that’s caused by the limits of the human eye, the same illusion that allows
movies, which are a series of still photos transmitted in sequence at a frequency of
about 24 per second, to appear to be a facsimile of real life.
9. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
We come up against a different type of limit when we start to transmit very high
frequencies in the megaHertz range – which is millions of cycles every second: the
limits of some of our present-day technologies.
What happens with high MHz frequencies is that the cycle switches from positive
to negative so fast that neither LED has time to switch on fully before it receives
the signal to switch off again. The result is the LEDs appear to go very dim, and
may even appear to be turned off completely.
10. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
This doesn't mean that Spooky2, the generator, or the Remote have
stopped working – just that current LED switching technology isn't fast
enough to keep up with what's happening with an extremely fast signal.
This is nothing to worry about.
11. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Remote & amplitude
However, there's another scenario where the LEDs can appear to be very dim, or
even unlit – and this one doesn't involve very high frequencies at all.
Every time an LED lights up, it uses a very tiny fraction of the frequency's motive
power – amplitude, otherwise known as voltage. At amplitudes above about 5volts,
you won't really see any difference in the luminance of the LEDs.
12. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
However, if you set your amplitude lower than this, the voltage available
to light up the LEDs drops off, and the result is that they appear to be
dim. At very low amplitudes, they will look like they're not working at all.
This is also nothing to worry about. In fact, it's a good thing because it
means that all of the frequency's voltage is being used for the purpose
intended – healing.
13. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Thank you!