This document provides an overview of carpentry tools and their proper use and maintenance. It begins by outlining three learning outcomes related to checking tools and understanding how to demonstrate their use. Several common carpentry tools are then described, including measuring tools like rulers and pull-push rules, marking tools, levels, saws, hammers, and screwdrivers. The document also discusses tool classification and holding tools. It concludes by outlining activities for students, such as demonstrating tool use, applying lubricant, and creating an educational video about a carpentry tool.

1. POTOT JOEY M Jr.
Student Teacher

2. MAINTAIN TOOLS AND EQUIPMENT
LESSON II
Technology and Livelihood
Education
CARPENTRY

6. LEARNING OUTCOMES:
LO 1. Check condition of tools and equipment
LO 2. Understanding the tools and equipment
LO 3. Demonstrate the tools and equipment available
in there homes.
At the end of this Lesson, you are expected to do the
following:

7. Activity
Carpentry tools that you can find in your
home.
Please follow the format bellow.
1.
2.
3.
4.
5.

8. Carpentry is a skilled trade
and a craft in which the primary
work performed is the
cutting,shaping and Instagram of
building materials during the
construction of
buildings,ships,timber and
bridges,concrete formwork,etc.
CARPENTRY

9. CLASSIFICATIONS
OF
HANDTOOLS

10. Measuring tools is used to
measure a physical quantity. All
measuring instruments/ tools are
subject to varying degrees of
instrument error and measurement
uncertainty.

11. 1. Pull-Push Rule - flexible tape that slides into a
material case and it is used to measure irregular
and regular shapes.
2. Ruler - 12-inch or one foot rule and it is used
to take/make simple measurements.

13. 1. Pencil - used to layout or mark cutting lines.
2. Marking Gauge - wood or metal tool consisting
of a beam, head and a point used to mark a line
parallel to the grain of the wood.

14. 3. Chalk Line - used to establish a straight line on a
surface.
4. Divider - tool with two metal legs used to lay-out
an arc circle or step
off division on a line.
5. Compass - used to scribe arcs and circle in a
metal wood.

16. 3. Spirit Level - tool used for testing vertical and
horizontal surfaces.
4. Plumb bob - tool used to test the vertical and
horizontal surfaces.

17. 1. Chisel - tool used to trim and shape wood.
2. Plane - used to obtain a smooth and flat
surface.

18. 3. Spoke shave - small plane like tool from
irregularly shaped objects.
4. Cabinet scraper - rectangular piece of steel with
two cutting edges used for working flat and curved
shapes.

19. Tooth cutting tools are the
main tools for a carpenter. The
most commonly used saws by a
carpenter are the crosscut saw, rip
saw, the back saw and hack saw.

20. 1. Cross Cut Saw - handsaw used to cut the wood
across the grain.
2. Rip-saw - hand saw used to cut the wood along
the grain.

21. Holding tool is a support device
often used in the manufacturing
industry to securely position a tool in a
specific spot or orientation.

22. 1. C-Clamp - used for holding
together pieces of lumber
while working.
2. Bench Vise - used to hold
any materials or tools in place.
3. Bar Clamp - used to hold
large boards or frames together
while assembling or gluing.

23. 1. Claw Hammer - used to
drive and pull out nails on
wooden surfaces.
2. Mallet - made out of wood
or rubber used to drive other
tools like chisel.

24. 3. Nail Set - used in setting
the head of a finishing nail
below the surface of the
wood.
4. Screw Driver - used to
drive and loose screws.

26. 1. Read and analyze the use of preventive
Maintenance Schedule form.
2. Determine the types of tools and machine
needed to be lubricated.
3. Fill out a requisition slip form in releasing the
lubricants needed.
4. Secure a borrower’s slip from your teacher.
5. Fill out the slip form correctly intended for the
needed tools.

27. 6. Perform the task according to the prescribed
schedule and the assigned machine.
7. Perform lubricating procedure.
8. Determine the parts of the machine needed to
be lubricated.
9. Apply thin coat of oil on the parts for a long
period of time.
10. Open the bearing cover and apply grease.
11. Apply grease on sealed bearing with the use of
a grease gun.

28. Group youself into four (4). Each group will
prepare a short demonstration about proper
use of some carpentry tools for 5 minutes.
Scoring Descriptions
5 Demonstrates the complete undertanding of
the function of the tool.
4 Demonstrates the considerable
undertanding of the fuction of the tool.
3 Demonstrates the partial undertanding of
the function of the tool.
2 Demonstrates the lttle undertanding of the
function of the tool.
1 Demonstrates the no undertanding of the
function of the tool.
0 No response/Tast not attempted
RUBRICS

29. Iwant you to get 1/4 sheet of paper, I
well only read the questions twice and
write the correct answer on your 1/4
sheet of paper.

30. Look for a carpentry tool available in your
home and make a short video clip about the
proper usage of that tool. Post it in our private
page.

31. THANK YOU
FOR
LISTENING