United Electric TX200 Pressure TransmitterIves Equipment
The TX200 is a compact, rugged pressure transmitter utilizing ASIC technology to provide optimum sensor signal conditioning and temperature compensation of the sensor output. It is designed for process control industries worldwide and ideally suited for petrochemical and upstream oil and gas applications. The TX200 provides a cost-effective solution to using conventional process transmitters.
The xed range model tX200B is recommended for use where process pressure is consistent within the range and where physical access to the transmitter is limited or not required.
The eld adjustable model tX200a allows access to zero and span the transmitter. The transmitter may be spanned up to 5:1 and for ease of calibration, does not require a calibrated pressure source and can be calibrated in-place.
The DUSTHUNTER C200 is a type-approved measuring device which combines the advantages
of the measuring principles of transmittance and forward scattered light. It is, therefore, ideal for
measuring very low to high dust concentrations. Automatic self-alignment optimizes the position
of the measuring beam and prevents incorrect measurement. An automated check of the zero
and reference point as well as a contamination check are on board in the device.
Designed to provide thorough, continuous monitoring of many hazardous gases, the indoor/outdoor Ultima X Series Gas Monitors offer excellent performance and MSA quality craftsmanship. DuraSource™ Technology offers extended sensor life, while HART provides convenient setup, calibration and diagnostics. HART also allows for existing component install and wiring to be used. A single circuit board increases reliability, while our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification. The units are crafted from either stainless steel or polycarbonate, and the interchangeable smart sensors eliminate the need for reconfiguration. Our scrolling LCD screen display sensor reading and gas type, while the calibration process includes date stamping and the ability to calibrate locally or remotely.
Portable flow meter for measurement of compressed air, gases, and heat quanti...Classic Controls, Inc.
The FLUXUS G601 CA Energy is the ideal tool for carrying out complete energy efficiency tasks in the industry as well as within facility management by allowing the measurement of compressed air flow rates as well as the monitoring of thermal energy quantities and the flow rate determination of any kind of liquid or gaseous media with just one device.
A full line of microBlox™ isolated signal conditioning modules are now available from Acromag. microBlox™ uB Signal Conditioning ModuleOffering over 175 models, microBlox uB modules can safely interface a wide variety of voltage, current, temperature, frequency, and other field signals with a ±5V or 0-5V DC output to host measurement & control systems. Users can select modules with fixed ranges or wireless configuration via Bluetooth® wireless technology on an Android™ or iOS® mobile device.
Magnetrol TA2 Thermal Mass Flow Meter for Flare Gas ApplicationsMiller Energy, Inc.
Low flow sensitivity means high reliability for flare gas applications. The Thermatel® TA2 thermal dispersion mass flow meter provides reliable mass flow measurement for flare gas applications to comply with monitoring requirements.
United Electric TX200 Pressure TransmitterIves Equipment
The TX200 is a compact, rugged pressure transmitter utilizing ASIC technology to provide optimum sensor signal conditioning and temperature compensation of the sensor output. It is designed for process control industries worldwide and ideally suited for petrochemical and upstream oil and gas applications. The TX200 provides a cost-effective solution to using conventional process transmitters.
The xed range model tX200B is recommended for use where process pressure is consistent within the range and where physical access to the transmitter is limited or not required.
The eld adjustable model tX200a allows access to zero and span the transmitter. The transmitter may be spanned up to 5:1 and for ease of calibration, does not require a calibrated pressure source and can be calibrated in-place.
The DUSTHUNTER C200 is a type-approved measuring device which combines the advantages
of the measuring principles of transmittance and forward scattered light. It is, therefore, ideal for
measuring very low to high dust concentrations. Automatic self-alignment optimizes the position
of the measuring beam and prevents incorrect measurement. An automated check of the zero
and reference point as well as a contamination check are on board in the device.
Designed to provide thorough, continuous monitoring of many hazardous gases, the indoor/outdoor Ultima X Series Gas Monitors offer excellent performance and MSA quality craftsmanship. DuraSource™ Technology offers extended sensor life, while HART provides convenient setup, calibration and diagnostics. HART also allows for existing component install and wiring to be used. A single circuit board increases reliability, while our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification. The units are crafted from either stainless steel or polycarbonate, and the interchangeable smart sensors eliminate the need for reconfiguration. Our scrolling LCD screen display sensor reading and gas type, while the calibration process includes date stamping and the ability to calibrate locally or remotely.
Portable flow meter for measurement of compressed air, gases, and heat quanti...Classic Controls, Inc.
The FLUXUS G601 CA Energy is the ideal tool for carrying out complete energy efficiency tasks in the industry as well as within facility management by allowing the measurement of compressed air flow rates as well as the monitoring of thermal energy quantities and the flow rate determination of any kind of liquid or gaseous media with just one device.
A full line of microBlox™ isolated signal conditioning modules are now available from Acromag. microBlox™ uB Signal Conditioning ModuleOffering over 175 models, microBlox uB modules can safely interface a wide variety of voltage, current, temperature, frequency, and other field signals with a ±5V or 0-5V DC output to host measurement & control systems. Users can select modules with fixed ranges or wireless configuration via Bluetooth® wireless technology on an Android™ or iOS® mobile device.
Magnetrol TA2 Thermal Mass Flow Meter for Flare Gas ApplicationsMiller Energy, Inc.
Low flow sensitivity means high reliability for flare gas applications. The Thermatel® TA2 thermal dispersion mass flow meter provides reliable mass flow measurement for flare gas applications to comply with monitoring requirements.
Yokogawa has a long history of supplying process gas chromatographs to the oil & gas, refining and petrochemical industries around the world. The new process GC that meets the ever growing demands for analytical reliability and precision while improving the total cost-of ownership through built-in automated maintenance functions never seen before.
From the innovative 12-inch color touch screen HMI to the powerful predictive diagnostics, the GC8000 is truly a process GC for the 21st century. But the GC8000 is not just all about new electronics; it also brings a number of important innovations in gas chromatograph analytical capabilities. For the first time, parallel chromatography is made practical with the introduction of the GC Module (GCM) concept. By setting up virtual GCs within a single analyzer, all chromatograph settings, displays, and data are truly segregated for easy understanding and maintenance. There are even built-in graphical overview screens showing each of the individual GC Modules.
The GC8000 sets new standards for process gas chromatography while at the same time offering hardware and electronics that are recognized for robust and reliable operation.
Liquisys M CPM223/253. pH/ORP Measurement. Transmitter for analog and digital glass and ISFET sensors. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Process control Solutions (PCS) offers the finest selection of Industrial Instrumentation and Control products in the world, and is uniquely qualified to provide application / technical support, installation and calibration services and product selection from an extensive line of industries.
Parker Balston is a division of Parker Hannifin, world’s leading diversified manufacturer of motion and control technologies and systems. Balston manufacturers industrial filters and filtration technology, replacement filter elements, compressed air dryers, nitrogen generators, and compressed air microbial detection.
Magnetic flow meter for industrial process measurementCTi Controltech
Enhanced signal conditioning circuitry provides excellent noise and spike immunity
High stable and repeatable output with ±0.5% of rate accuracy
Minimum process fluid conductivity requirement of 10μS/cm provides maximum applicability
Electrode Status Diagnostic function diagnoses empty pipe condition or electrode scaling
Available in wafer of flanged designs
Both Integral and Remote configurations are available for maximum flexibility
Siemens catalog tong hop sidac transformerDien Ha The
Siemens ,
Catalog Thiết Bị Điện Siemens , Catalog Thiết Tự Động
Catalog Phụ Kiện Siemens , Catalog Phụ Kiện,
Catalog Siemens , Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Siemens vui lòng gọi: 0907.764.966
For integrated, cost effective moisture analysis for OEM’s and multiple sampling points. When simple, accurate moisture
measurement is required, the MM300 is the ideal choice.
Designed with the OEM user in mind, the MM300 transducer and monitor can be easily integrated into a wide range of systems.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
The DO7Plus is a 10A Microhmmeter, suitable for applications within Aerospace, Utilities, Cable or Machine Manufacturers or where a cooling curve is required to plot peak resistance. Hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Yokogawa has a long history of supplying process gas chromatographs to the oil & gas, refining and petrochemical industries around the world. The new process GC that meets the ever growing demands for analytical reliability and precision while improving the total cost-of ownership through built-in automated maintenance functions never seen before.
From the innovative 12-inch color touch screen HMI to the powerful predictive diagnostics, the GC8000 is truly a process GC for the 21st century. But the GC8000 is not just all about new electronics; it also brings a number of important innovations in gas chromatograph analytical capabilities. For the first time, parallel chromatography is made practical with the introduction of the GC Module (GCM) concept. By setting up virtual GCs within a single analyzer, all chromatograph settings, displays, and data are truly segregated for easy understanding and maintenance. There are even built-in graphical overview screens showing each of the individual GC Modules.
The GC8000 sets new standards for process gas chromatography while at the same time offering hardware and electronics that are recognized for robust and reliable operation.
Liquisys M CPM223/253. pH/ORP Measurement. Transmitter for analog and digital glass and ISFET sensors. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Process control Solutions (PCS) offers the finest selection of Industrial Instrumentation and Control products in the world, and is uniquely qualified to provide application / technical support, installation and calibration services and product selection from an extensive line of industries.
Parker Balston is a division of Parker Hannifin, world’s leading diversified manufacturer of motion and control technologies and systems. Balston manufacturers industrial filters and filtration technology, replacement filter elements, compressed air dryers, nitrogen generators, and compressed air microbial detection.
Magnetic flow meter for industrial process measurementCTi Controltech
Enhanced signal conditioning circuitry provides excellent noise and spike immunity
High stable and repeatable output with ±0.5% of rate accuracy
Minimum process fluid conductivity requirement of 10μS/cm provides maximum applicability
Electrode Status Diagnostic function diagnoses empty pipe condition or electrode scaling
Available in wafer of flanged designs
Both Integral and Remote configurations are available for maximum flexibility
Siemens catalog tong hop sidac transformerDien Ha The
Siemens ,
Catalog Thiết Bị Điện Siemens , Catalog Thiết Tự Động
Catalog Phụ Kiện Siemens , Catalog Phụ Kiện,
Catalog Siemens , Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Siemens vui lòng gọi: 0907.764.966
For integrated, cost effective moisture analysis for OEM’s and multiple sampling points. When simple, accurate moisture
measurement is required, the MM300 is the ideal choice.
Designed with the OEM user in mind, the MM300 transducer and monitor can be easily integrated into a wide range of systems.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
The DO7Plus is a 10A Microhmmeter, suitable for applications within Aerospace, Utilities, Cable or Machine Manufacturers or where a cooling curve is required to plot peak resistance. Hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Process Control Instruments India - Canopus Instrumentssmita_kale
Canopus Instruments manufactures top quality instrumentation and process control products. Buy the best industry products at Canopus Instruments now. https://www.canopusinstruments.com/product/industrial-automation-product/process-controller-indicators/digital-process-indicator/
ALIA Multi-Function Calibrator ACA60
ACA60 is mainly designed for the calibration and maintenance of on-site industrial thermodynamic(al) instrument and their system.
Its complete and practical functions are easily accessible. With latest extensive digital-converted integrative circuit and large-screen display, it is supplied with functions of output, measurement, ITS-90 query and 24VDC power supply, making it convenient for you to check and calibrate sensor, transmitter, displayed instruments, and control system on spot.
FEATURES
Large 2-line LCD with backlit display
Sources and reads mA, mV, V, Ohms, RTD and frequency
Keypad to enter output parameters directly
Simultaneous millivolt display when in temperature measurement mode
Small, streamlined shape, easy to carry and hold
Thermocouple measurement/output with automatic or manual cold junction compensation
Quick query to resistance & temperature, and millivolt & temperature
24VDC loop power supply
Ni-MH battery available, continuous use for at least 6 hours
Concurrent input/output, convenient to operate
SPECIFICATION
Response Time:80ms
Operating Temp.:10 ~ +55 deg.c
Display:2'' (128*64 Pixels), Backlight LCD
Battery Operation:6-8 Hours
Charge Time:8-12 Hours
Battery Type:NiMH Pack, 1800 mAh, 7.2VDC
Charger Supply:90 ~ 260VAC 50/60 Hz
Dimension: Calibrator-231 *104 * 39mm
Carrying Case-330 * 250 * 150mm
Weight:0.7 Kg
Enclosure:IP54
RUGGED MONITORING’s R501 is the most versatile and advanced multi-channel monitoring solution. Designed to seamlessly integrate into diverse industries, the R501 stands as a testament to our commitment to innovation and reliability in electrical asset monitoring.
Allwin21 Corp. was formed in 2000 with a focus on professionally providing Rapid Thermal Process, Plasma Asher Strip / Descum, Plasma Etch/RIE, Sputter Deposition and Metal Film Metrology high-tech semiconductor equipment, services and technical support in Semiconductor III-V, MEMS, Biomedical, Nanotechnology, Solar, Battery & LED industries. We endeavor to be a leader in our product lines.
We focus on extending product lifecycle, providing solutions, and engineering enhancements to many production proven semiconductor process equipment most directly related to III-V processing. These semiconductor equipment have been used in production and R&D since the 1990′s. They have proven processes and research. Allwin21 Corp. customizes these systems with Allwin21′s comparable integrated process control system with PC, solid robotic wafer transfer system, and new critical components. This is to achieve the goal of giving our customers a production edge, with right cost, and without having to worry about obsolete parts.
The HY-OPTIMA™ 1700 is an intrinsically safe device that incorporates our patented solid-state sensor and is configured to operate in background gas streams with up to 95% relative humidity and temperatures up to 100ºC.
The AW-901eR & AW-903eR single-wafer dry etchers are automated tools designed as a flexible 13.56MHz RF Parallel Plate plasma etching systems for high-volume wafer fabrication. AW-901eR & AW-903eR are in direct response to manufacturer’s concerns for wafer breakage, Uniformity, Uptime, Reliability, and Production-Proven technology
Schneider,
Catalog Thiết Bị Điện Schneider, Catalog Thiết Bị Điện
Catalog Phụ Kiện Schneider, Catalog Phụ Kiện,
Catalog Schneider, Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Schneider tại https://dienhathe.com
Xem thêm các Catalog khác của Schneider tại https://dienhathe.info
Để nhận báo giá sản phẩm Schneider vui lòng gọi: 0907.764.966
Schneider,
Catalog Thiết Bị Điện Schneider, Catalog Thiết Bị Điện,
Catalog Phụ Kiện Schneider, Catalog Phụ Kiện,
Catalog Schneider, Catalog,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Schneider tại https://dienhathe.com
Xem thêm các Catalog khác của Schneider tại https://dienhathe.info
Để nhận báo giá sản phẩm Schneider vui lòng gọi: 0907.764.966
Schneider,
Catalog Thiết Bị Điện Schneider, Catalog Thiết Bị Điện
Catalog Phụ Kiện Schneider, Catalog Phụ Kiện,
Catalog Schneider, Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Schneider tại https://dienhathe.com
Xem thêm các Catalog khác của Schneider tại https://dienhathe.info
Để nhận báo giá sản phẩm Schneider vui lòng gọi: 0907.764.966
Learn about a1-cbiss' refrigeration solutions that cover everything from refrigerant leak detection and monitoring through to emissions control in this brochure
Ideal for oil exploration and extraction the MSA Ultrasonic Gas Detector offers a wide range of detection information. Find out more in this datasheet prepared by gas detection specialists a1-cbiss.
1. a1-cbiss
RMS8000
Datasheet
The RMS8000 Gas Monitor is an innovative, cost effective, wall mounted
unit. It is designed to operate in conjunction with the RGS8000 series
sensors to monitor concentrations of carbon dioxide, ammonia, HCFC/
HFC or combustible gases refrigeration applications.
The gas concentration is indicated on a 4-digit, 7-segment display while
another 2-character alphanumeric display indicates instrument status. A
third display indicates the active channel.
Simple to use and microprocessor controlled, the RMS8000 is menu
assisted and user programmable for alarm setpoints and relay options
in a user friendly manner offering unique flexibility and control over the
system.
The RMS8000 is mains powered (230Vac standard, 110Vac optional) and
has changeover circuitry to facilitate an external 12V rechargable battery
and charger to be connected to ensure uninterrupted operation in the
event of a mains power failure.
Careful product design and rigorous product testing combined with a
stringent ISO9002 quality assurance program ensure ultimate reliability.
The a1-cbiss RMS8000 offers a robust, easy to use, cost effective approach
to providing an effective refrigerant gas monitoring system
Overview
Refrigerant Monitoring
The a1-cbiss RMS8000 is a wall mounted monitor to
monitor concentrations of carbon dioxide, ammonia, HCFC/
HFC or combustible gases in refrigerant applications. It is
designed to operate with the a1-cbiss RGS8000 series of
sensors.
Automatic self-test
The microprocessor implements a comprehensive self-test
routine, continually monitoring the system’s performance
and functionality. The self-test routine examines the integrity
of the system’s electronic circuitry, system software, sensor
cabling, sensor signal, ancillary cabling etc. In the unlikely
event of a fault, the digital display will indicate the nature of
the condition in a user-friendly diagnostic mode.
026
Certificate Number 996QM8001
Features
• Voltage free relay contacts
• Digital readout
• Low power consumption
• Alarm inhibit during calibration
• Individual 4-20mA analogue outputs
• Sealed to IP65 rating
t: +44(0)151 666 8300 f: +44(0)151 666 8329 e: sales@a1-cbiss.com www.a1-cbiss.com
2. a1-cbiss
RMS8000
Specification
Mechanical Specifications
Height 230mm
Width 300mm
Depth
110mm
Weight 4.0Kg
Mounting holes
4 holes, Ø4.2mm, spaced at 200mm (vert) 288mm (horz)
Environmental Specifications
Operating temperature
Storage temperature
Humidity range
-18˚C to +60˚C
-40˚C to +66˚C
10%RH to 90%RH (Non-condensing)
Electrical Specifications
Supply voltage
230Vac (115Vac optional)
Power consumption
12W
Mains fuse 2A’T’
Transformer secondary fuse
2A’T’ PCB mounted 5 x 20mm fuse
Battery fuse
2A’T’ PCB mounted, 5 x 20mm fuse
Sensor cables
3 core, screened, 0.5mm2 to 1.5mm2
Relay contacts
SPDT, 250V, 3A each for Alarm1, Alarm2 and FAULT (3 relays)
Analogue outputs
4-20mA into maximum 250 Ω for each channel
Combustible gas sensor type
RGS8000 semiconductor adsorbtion combustible gas sensor
HCFC/HFC gas sensor type
RGS8000 semiconductor adsorbtion HCFC/HFC gas sensor
Ammonia gas sensor type
RGS8000 semiconductor adsorbtion ammonia gas sensor
Carbon dioxide sensor type
RGS8000 NDIR carbon dioxide gas sensor
Stabilisation time
45 seconds
Annunciator output
2.5kHz, 84dB(A) @ 1m
Transient protection
PCB mounted Metal Oxide Varistor
Terminations
PCB headers & detachable terminal blocks up to for 1.5mm2 cable
Alarm setting
Digital setting (adjustable between 10% and 90% of full scale)
Alarm types
Energised/de-energised (FAULT is normally enerfised only)
Resolution 1%
Accuracy
5%
Full scale range
0-5, 0-100, 0-1000, 0-5000 (user selectable)
User variable storage
Non-volatile RAM (EEPROM)
Enclosure material
Two-piece, hinged, ABS or polycarbonate
026
Certificate Number 996QM8001
t: +44(0)151 666 8300 f: +44(0)151 666 8329 e: sales@a1-cbiss.com www.a1-cbiss.com