This document provides installation instructions for a wireless security detector. It recommends mounting the detector indoors, at least 1 meter away from large metal objects to avoid false alarms. The detector should be mounted on a stable surface between 2-3 meters high for optimal coverage of up to 15 meters. Instructions are provided for removing the chassis and battery, as well as adjusting mounting height and coverage area through settings.

1. INTRODUCTION CHOOSING A LOCATION Avoid common false alarm sources MOUNTING
• For wireless connectivity, detailed programming Do not install close to large metal For indoor use only
INSTALLATION INSTRUCTIONS
and system set-up instructions please refer to objects or mains wiring
the compatible RICOCHET™ technology enabled
>1m Metal Lintel
Premier wireless expander instructions.
• Featuring RICOCHET™ wireless technology the
Prestige XT-W and Prestige QD-W are designed
for professional security installations.
>1m
✗ ✓
>1m
Mount on a stable surface
230V
110V
✗ ✓ ✓
Metal Filing
Cabinet
INS 466
STANDARDS COVERAGE & PICK-UP M
OUNTING HEIGHT & SETTINGS ALTERING COVERAGE AT 2m MOUNTING HEIGHT
EN50131-2-2, EN50131-5-3, EN50131-1,
Alarm Systems:
PD6662, Grade 2 Class II 2m
EN50130-4:1995: A1: A2 6'7"
EMC:
ETSI EN301 489-03 V1.4.1
3.0m/9’10”
R&TTE: E
TSI EN300-220 (V2.1.1)
Environmental: E
N50130-5
Frequency Band: 868.0 MHz - 868.6 MHz
BATTERY SAFETY 2m 8m
2.5m/8’2” 26'2
6'7
• Do not throw into a fire • Do not heat
• Do not short circuit • Do not charge
• Replace only with same or equivalent type • Do not disassemble
• Always observe local regulations when disposing of a battery
• Detector will transmit low battery warning when battery needs replacing 2.0m/6’7”
Volumetric 10m
WARRANTY 2m 32'9
2 year replacement warranty (excludes battery).
Top View
Metres
6'7
The Prestige XT-W/QD-W is designed to detect the movement of an
intruder and activate an alarm control panel. As the Prestige XT-W/QD-W 15m
1.5m/4’11”
is not a complete alarm system, but only a part thereof, Texecom cannot
accept responsibility or liability for any damages whatsoever based on a
claim that the Prestige XT-W/QD-W failed to function correctly. 2m 15m
50'
Metres
Metres
6'7
Due to our policy of continuous improvement Texecom reserves 12m 12m
the right to change specification without prior notice. All specifications
are measured at 20ºC (68ºF).
Made In
England 15m
2m 50'
Side View 6'7
2m
6'7
Cer tificate Number: FM 35285
Prestige and the wireless logo are trade marks of Texecom Ltd. © 2010 ANGLING THE
The Prestige XT-W/QD-W is protected by European Registered Design. No: 3004997 DETECTOR
15m 4m
A20100211 INS466 50' 13'1

2. HOW TO REMOVE THE CHASSIS D
ETECTOR KNOCKOUTS CEILING MOUNT BRACKET*
Remove chassis before mounting
the detector
1 2 3 4
6
5
WALL MOUNT BRACKET*
7
1 2 3 4
Note:
Rear Tamper Insert For EN 50131 compliance both the detector and
the rear tamper insert must be fixed to the wall,
mounting brackets should not be used.
*Available Separately
XT PULSE COUNT 40mm
Battery Tag 1 (1.6”)
Remove on installation.
JP1
112.25mm
2 (4.4”)
JP1
3
0.3 - 3.0m/s
1 - 10ft/s
60mm 160g (5.5oz)
JP1
(2.4”) approx.
LED
Indication only available in QD PULSE COUNT
walktest mode. 1
(See Premier wireless
expander instructions) -35°C (-31°F) to
JP1
+55°C (+131°F)
Learn Switch
2
Hold down during battery
connection to learn device.
JP1
3 -35°C (-31°F) to
0.3 - 3.0m/s +60°C (+140°F)
1 - 10ft/s
Mounting Height Settings JP1