This document summarizes a bachelor's thesis on optimizing pressure loss in a sprinkler valve. The thesis involved researching fluid mechanics principles, high pressure water mist systems, and classification standards. It then conducted an extensive feasibility study and CFD simulations on the valve's design. This uncovered deviations from theoretical predictions due to simplifying assumptions. Several potential redesigned concepts were simulated, with the best concept upgraded and field tested. The final optimized design achieved the project's goal of reducing pressure loss through the valve, improving water mist system functionality for land and marine applications.
Use of hydraulic phenomena in enhancement of dissolved oxygen concentrationeSAT Journals
Β
Abstract
The dissolved oxygen (DO) content of water bodies is an indicator of water quality and hence a measure of ability of water to sustain aquatic life. Hydraulic phenomena such as hydraulic drops and hydraulic jumps can increase the amount of DO in the water by creating turbulent conditions. The main reason for this oxygen transfer is the air entrainment into the flow through large number of air bubbles that helps in air-water transfer. The present study investigates the effect of different weir types and hydraulic jump on their aeration efficiency. Two types of weirs namely rectangular and triangular weirs were used in the study. Also, the hydraulic jump was studied as an aeration agent. From the experimental results, it was found that the triangular weir provides greater aeration efficiency of 0.1948 as compared with rectangular weir that had aeration efficiency of 0.1012. On the other hand, the hydraulic jump showed aeration efficiency of 0.14285. As the weirs are more efficient than hydraulic jump, they are most applicable in the field. Also, weir structures are less expensive when compared with the structural arrangement required for the formation of hydraulic jump.
Keywords: Dissolved oxygen, Aeration efficiency, Weir, Hydraulic jump
Modelling and Stress Analysis of the Pig Loop Module of a Piping System.IJRES Journal
Β
The failure of any piping system depends on the stress analysis that was performed during the engineering design of the piping system. In designing the pig loop of a submarine manifold to be used in area Y of Niger delta in Nigeria, a proper analysis of the load to which the system could be subjected was carried out using a stress analysis software - ''Triflex piping solutions.'' We employed ASME B31.8 piping code. Various stress values and deflections were analysed at each node to ensure that the design will be on a safe operating condition. Stress utilization was checked for hoop and longitudinal stresses for various scenarios and the worst case scenario was determined. The maximum stress utilization for the worst case scenario was found to be within the limit and thereby meeting with the safety requirement.
Liquid Piping Systems, Minor Losses: Fittings and Valves in Liquid Piping Systems, Sizing Liquid Piping Systems; Fluid Machines (Pumps) and PumpβPipe Matching, Design of Piping Systems complete with In-Line or Base-Mounted Pumps
Impact of Crack Length into Pipe Conveying Fluid Utilizing Fast Fourier trans...IJECEIAES
Β
One of the most prominent problems experienced by the oil facilities is leakage of oil from the pipes. This problem caused 55% of oil refineries to be shut off. Oil leakage is a common problem that often results in oil waste, damage, and hazard to public health. Therefore, it is necessary to use Modern technologies to reduce this phenomenon and avoid them in advance. Pipes that convey fluids have many uses in various industries and living facilities. Risk increases when the fluid inside the pipe is flammable. In this work, main case that cause damage to the pipe, longitudinal crack is investigate.This work presents a new experimental model based on computer applications with a Fast Fourier transform (FFT) algorithm for testing the effect of longitudinal crack length by frequency and ultrasonic measurements to measure fluid velocity. The method is used for plastic pipe with 2 cm internal diameter, 3 cm external diameter, and 1 m length. The modulus of elasticity of the material is 800 N/mm2 according to the ISO 178 test method. The pipe conveys oil with simply supported ends. The results show that FFT model shows better features compared with other ways that depends on visual inspection or localized measurements which gave an external perception of pipeline damage. FFT model offers a reliable and cheap style for ensuring pipeline integrity and warning the risks before its occurrence. From the observations made the fundamental natural frequency (FNF) decreases by increasing of crack length in the pipe that conveys fluid.
Use of hydraulic phenomena in enhancement of dissolved oxygen concentrationeSAT Journals
Β
Abstract
The dissolved oxygen (DO) content of water bodies is an indicator of water quality and hence a measure of ability of water to sustain aquatic life. Hydraulic phenomena such as hydraulic drops and hydraulic jumps can increase the amount of DO in the water by creating turbulent conditions. The main reason for this oxygen transfer is the air entrainment into the flow through large number of air bubbles that helps in air-water transfer. The present study investigates the effect of different weir types and hydraulic jump on their aeration efficiency. Two types of weirs namely rectangular and triangular weirs were used in the study. Also, the hydraulic jump was studied as an aeration agent. From the experimental results, it was found that the triangular weir provides greater aeration efficiency of 0.1948 as compared with rectangular weir that had aeration efficiency of 0.1012. On the other hand, the hydraulic jump showed aeration efficiency of 0.14285. As the weirs are more efficient than hydraulic jump, they are most applicable in the field. Also, weir structures are less expensive when compared with the structural arrangement required for the formation of hydraulic jump.
Keywords: Dissolved oxygen, Aeration efficiency, Weir, Hydraulic jump
Modelling and Stress Analysis of the Pig Loop Module of a Piping System.IJRES Journal
Β
The failure of any piping system depends on the stress analysis that was performed during the engineering design of the piping system. In designing the pig loop of a submarine manifold to be used in area Y of Niger delta in Nigeria, a proper analysis of the load to which the system could be subjected was carried out using a stress analysis software - ''Triflex piping solutions.'' We employed ASME B31.8 piping code. Various stress values and deflections were analysed at each node to ensure that the design will be on a safe operating condition. Stress utilization was checked for hoop and longitudinal stresses for various scenarios and the worst case scenario was determined. The maximum stress utilization for the worst case scenario was found to be within the limit and thereby meeting with the safety requirement.
Liquid Piping Systems, Minor Losses: Fittings and Valves in Liquid Piping Systems, Sizing Liquid Piping Systems; Fluid Machines (Pumps) and PumpβPipe Matching, Design of Piping Systems complete with In-Line or Base-Mounted Pumps
Impact of Crack Length into Pipe Conveying Fluid Utilizing Fast Fourier trans...IJECEIAES
Β
One of the most prominent problems experienced by the oil facilities is leakage of oil from the pipes. This problem caused 55% of oil refineries to be shut off. Oil leakage is a common problem that often results in oil waste, damage, and hazard to public health. Therefore, it is necessary to use Modern technologies to reduce this phenomenon and avoid them in advance. Pipes that convey fluids have many uses in various industries and living facilities. Risk increases when the fluid inside the pipe is flammable. In this work, main case that cause damage to the pipe, longitudinal crack is investigate.This work presents a new experimental model based on computer applications with a Fast Fourier transform (FFT) algorithm for testing the effect of longitudinal crack length by frequency and ultrasonic measurements to measure fluid velocity. The method is used for plastic pipe with 2 cm internal diameter, 3 cm external diameter, and 1 m length. The modulus of elasticity of the material is 800 N/mm2 according to the ISO 178 test method. The pipe conveys oil with simply supported ends. The results show that FFT model shows better features compared with other ways that depends on visual inspection or localized measurements which gave an external perception of pipeline damage. FFT model offers a reliable and cheap style for ensuring pipeline integrity and warning the risks before its occurrence. From the observations made the fundamental natural frequency (FNF) decreases by increasing of crack length in the pipe that conveys fluid.
REVIEW OF FLOW DISTRIBUTION NETWORK ANALYSIS FOR DISCHARGE SIDE OF CENTRIFUGA...ijiert bestjournal
Β
A computational fluid dynamics (CFD) analysis has been conducted to find the pressure losses for dividing and combining fluid flow through a junction of discharge system. Simulations are performed for a range of flow ratios and equations are developed for pressure loss coefficients at junctions. A mathematical model based on s uccessive approximations then would be employed to estimate the pressure losses. The proposed CFD based strategy can be used for the analysis of all the three pipe branches of s ome diameter are selected along with equal length so that only the effect of bend angle can be st udied. The effect of bend angle,pipe diameter,pipe length,reynolds number on the resistan ce coefficient is studied. The software used is CATIA for modeling and ANSYS fluent for analysis purpose.
about 70 % of the existing reservoirs are impossible to reach with conventional drilling . MPD or managed pressure drilling is the best solution for HPHT and very deep reservoirs .
Vortex Tube Usage in Cooling and Liquification Process of Excess Gases in Ghe...Samet Baykul
Β
DATE: 2019.05
- Computational analysis of a vortex tube
- Developing boundary conditions for heat transfer analysis
- CAD by creating a suitable model for heat transfer analysis
- CFD analysis by using ANSYS FLUENT
- Literature survey for recent academic studies
ABSTRACT:
Vortex tubes are simple and common devices which separates a high-pressure gas flow as two different lower gas flows. One of the outlets has a higher temperature than the inlet high pressure gas and other outlet has lower. Most common types of the vortex tubes are counter and parallel flow types. In counter flow type vortex tubes the cold and hot outlets are on opposite sides and in parallel flow type both the outlets are on the same side. Since it is a simple, well known, compact, portable, highly reliable and has a few initial costs, it could be desirable for the specific heating or cooling and refrigeration applications.
Recent Advancements in Piping industry and Piping materials.Asheesh Padiyar
Β
A brief overview of the new technologies that are available for piping engineers to know the latest advancements in piping materials . As a chemical engineer, it is essential to know about the various piping systems and technologies associated with it, in order to have a better understanding of their project/ process/ installing/ commissioning of the plants/ refineries.
Engineering DesignβDefinition; Types of Design in Thermo-Fluid Science; Difference between Design and Analysis; Classification of Design; General Steps in Design; Abridged Steps in the Design Process
A REVIEW ON IMPROVEMENT OF EFFICIENCY OF CENTRIFUGAL PUMP THROUGH MODIFICATIO...ijiert bestjournal
Β
The paper reviews the literature available on the i mprovement of efficiency of centrifugal pump through modification in suction manifolds. The paper discusses the available material of performance improvement through various paramete rs and mainly focuses on the research related to manifold modifications.
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
Most engineers involved in the planning of pumping systems are familiar with the
terms water which cause series damage to pipe component such as pumps valves and
cause big losses of water called water Hammer.
-------------------------------------------------------------------------------------
βΊ You can visit my website
https://bit.ly/3rNZ4Ds
Follow us on
βΊ LinkedIn:
https://bit.ly/3yL9q8K
βΊ Instagram:
https://bit.ly/3yG9zdx
βΊ YouTube:
https://bit.ly/3q93r9G
-------------------------------------------------------------------------------------
#Water_Hammer #Valves #Joukowsky's_equation #Hazen_Williams_Equation #Darcy-Weisbach #Cole-Brooke_Equation #Haaland_Equation #Moody_chart #elimination_water_hammer #Surge_Tank #Air valve #Pressure_relief_valve #Check_valve #Control_valve #air_vessels #WaterCAD #Water_network #Pipe #Junction #Reservoir #Bentley HAMMER
REVIEW OF FLOW DISTRIBUTION NETWORK ANALYSIS FOR DISCHARGE SIDE OF CENTRIFUGA...ijiert bestjournal
Β
A computational fluid dynamics (CFD) analysis has been conducted to find the pressure losses for dividing and combining fluid flow through a junction of discharge system. Simulations are performed for a range of flow ratios and equations are developed for pressure loss coefficients at junctions. A mathematical model based on s uccessive approximations then would be employed to estimate the pressure losses. The proposed CFD based strategy can be used for the analysis of all the three pipe branches of s ome diameter are selected along with equal length so that only the effect of bend angle can be st udied. The effect of bend angle,pipe diameter,pipe length,reynolds number on the resistan ce coefficient is studied. The software used is CATIA for modeling and ANSYS fluent for analysis purpose.
about 70 % of the existing reservoirs are impossible to reach with conventional drilling . MPD or managed pressure drilling is the best solution for HPHT and very deep reservoirs .
Vortex Tube Usage in Cooling and Liquification Process of Excess Gases in Ghe...Samet Baykul
Β
DATE: 2019.05
- Computational analysis of a vortex tube
- Developing boundary conditions for heat transfer analysis
- CAD by creating a suitable model for heat transfer analysis
- CFD analysis by using ANSYS FLUENT
- Literature survey for recent academic studies
ABSTRACT:
Vortex tubes are simple and common devices which separates a high-pressure gas flow as two different lower gas flows. One of the outlets has a higher temperature than the inlet high pressure gas and other outlet has lower. Most common types of the vortex tubes are counter and parallel flow types. In counter flow type vortex tubes the cold and hot outlets are on opposite sides and in parallel flow type both the outlets are on the same side. Since it is a simple, well known, compact, portable, highly reliable and has a few initial costs, it could be desirable for the specific heating or cooling and refrigeration applications.
Recent Advancements in Piping industry and Piping materials.Asheesh Padiyar
Β
A brief overview of the new technologies that are available for piping engineers to know the latest advancements in piping materials . As a chemical engineer, it is essential to know about the various piping systems and technologies associated with it, in order to have a better understanding of their project/ process/ installing/ commissioning of the plants/ refineries.
Engineering DesignβDefinition; Types of Design in Thermo-Fluid Science; Difference between Design and Analysis; Classification of Design; General Steps in Design; Abridged Steps in the Design Process
A REVIEW ON IMPROVEMENT OF EFFICIENCY OF CENTRIFUGAL PUMP THROUGH MODIFICATIO...ijiert bestjournal
Β
The paper reviews the literature available on the i mprovement of efficiency of centrifugal pump through modification in suction manifolds. The paper discusses the available material of performance improvement through various paramete rs and mainly focuses on the research related to manifold modifications.
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
Most engineers involved in the planning of pumping systems are familiar with the
terms water which cause series damage to pipe component such as pumps valves and
cause big losses of water called water Hammer.
-------------------------------------------------------------------------------------
βΊ You can visit my website
https://bit.ly/3rNZ4Ds
Follow us on
βΊ LinkedIn:
https://bit.ly/3yL9q8K
βΊ Instagram:
https://bit.ly/3yG9zdx
βΊ YouTube:
https://bit.ly/3q93r9G
-------------------------------------------------------------------------------------
#Water_Hammer #Valves #Joukowsky's_equation #Hazen_Williams_Equation #Darcy-Weisbach #Cole-Brooke_Equation #Haaland_Equation #Moody_chart #elimination_water_hammer #Surge_Tank #Air valve #Pressure_relief_valve #Check_valve #Control_valve #air_vessels #WaterCAD #Water_network #Pipe #Junction #Reservoir #Bentley HAMMER
Flow analysis of centrifugal pump using CFX solver and remedies for cavitatio...IJERA Editor
Β
In this scholarly thesis pertinent to the working of centrifugal pump, a CFD solver namely CFX is employed in order to simulate fluid flow characteristics with well-defined constraints and boundary conditions defining the problem. Stringent solid model is meticulously prepared encompassing the present day usage and constructional features of a centrifugal pump and is constrained with various boundary conditions having fixed domain in order to evaluate plots and results. To spearhead and facilitate this analysis program a numerical approximation tool with high degree of convergence rate called ANSYS 15.0 software is used. The ASNYS software avoids tedious calculations presumably impending in the design procedure and uses ultimate numerical tool to approximate the solution of the partial differential equations associated with continuity, momentum and energy phases of a flow problem in a 3-D model. This exquisite feature of ANSYS enables designer to optimize the design procedure in an iterative manner based on the final plots of post-processing phase. In addition, the scholarly writing also constitutes the appraisal of the most debilitating and painstaking problem retarding the efficiency of the centrifugal pump known as cavitation. Possible remedies for overcoming this problem will be indirectly inferred from the various plots and figures derived from the post-processing phase of the design process.
Ca Hydraulic transient is a factor to be considered during structural design of water conveyance system. The most common hazardous situation is the uncontrolled pump trip due to power failure. Therefore, surge analysis is important for a water delivery project having long pipeline. Customized software WH 2.7 is used to solve the problem of surge in pipeline. Method of characteristics is widely used mathematical scheme for solving the phenomenon because of higher accuracy. The partial differential equations may be transformed by the method of characteristics into total differential equations. The later equations may then be integrated to yield finite differential equations which are conveniently handled numerically. This paper describes the problem of water hammer in long pipeline of lift irrigation scheme. The pumping station of lift irrigation scheme is located on riverbank and is to lift the water to the reservoir located at distance of 5.5 km through 1300mm diameter and 11 8 mm thickness mild steel pipeline. Three vertical turbine pumps each having capacity of delivering 0.937 m3 s total discharge capacity 2.8 m3 s and 43.24 m total head to irrigate the command area of 3300 ha. Continuous number of trials led to select combination of one air vessel of capacity 50 m3 and 10 Air Valves. Studies carried out helped to foresee advent conditions like column separation well in advance before implementation. This way it helps to finalize piping system incorporating anti surge devices like air vessel and air valves to keep the pipeline safe from water hammer due to power failure to the pumps and hence reliable operation for long run. Tomesh Kumar Sahu | Ashwini Bhoi | Kishor U. Farande "Water Hammer Analysis in Long Pipelines" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-7 | Issue-4, August 2023, URL: https://www.ijtsrd.com/papers/ijtsrd59823.pdf Paper Url:https://www.ijtsrd.com/other-scientific-research-area/other/59823/water-hammer-analysis-in-long-pipelines/tomesh-kumar-sahu
Butterfly valves are widely used in hydro power plants to regulate and control the flow
through hydraulic turbines. Thatβs why it is important to design the valve in such a way that it can give
best performance so that optimum efficiency can be achieved in hydraulic power plants. Conventionally
that the models of large size valves are straight in the laboratory to determine their performance
characteristics. This is a time consuming and costly process. High computing facility along with the use
of numerical techniques can give the solution to any fluid flow problem in a lesser time. In this research
work flow analysis through butterfly valve with aspect ratio 1/3 has been performed using
computational software. For modelling the valve ICEM CFD 12 has been used. Valve characteristics
such as flow coefficient and head loss coefficient has been determined using CFX 12 for different valve
opening angle as 30Β°,60Β°,75Β°, and 90Β° (taking 90Β°as full opening of the valve) for incompressible fluid.
Value of head loss coefficient obtained from numerical analysis has been compared with the
experimental results.
Fluid Dynamics Simulation of Two-Phase Flow in a Separator Vessel through CFDtheijes
Β
The poly (ethylene-co-vinyl acetate) - is an EVA polymer produced that has an important role in the National petrochemical industry chain. Understanding the fluid dynamic behavior during processing in pots separators is of fundamental interest for operational continuity. The drag of polymer melt to the top of the vase, is a source of interest to understand the behavior of the flow inside the machine and reduce contamination. The objective of this work is to study the phenomena the fluid dynamic behavior of EVA during processing inside the separator vessel, to propose a modification of the process. We performed numerical simulations of two-phase flow (gas and ethylene polymer melt), using the commercial computational fluid dynamics package CFX 5.5. The turbulence model used was the k-Ξ΅ for the fluid phase and a model with an Eulerian approach. The modeling used was satisfactory, because during the simulations, we studied the velocity profiles, concentration and trajectory of the biphasic mixture of fluids.
2015-2016 Mechanical/Civil Undergraduate Senior Design
Water Treatment by Hydrodynamic Cavitation and Ultraviolet Radiation
NEED:
1. ADD DETAIL TO DISCUSSION
2. ADD TABLE FOR BUDGET SECTION
3. NAMES ON PAGES
4. Environmental Section
5. Add the solid works model
6. Cover page
7. Add decision matrices
Submitted by
Christopher Bitikofer
Sarah Ridha
Brandyn Krieger
Terran Engle
Project Mentor
Chikashi Sato, Ph.D
Draft 2 Submitted: 11/6/2015
Table of Contents
Introduction 2
Discussion 3
Detailed Engineering Specifications: 4
System Piping and Instrumentation Diagram (P&ID) 5
Management 7
Budget 8
Appendices 9
Capability Statements 9
Gantt Chart 10
References 11
Introduction
Access to clean drinking water in underdeveloped areas of the world is a growing problem due to global increases in both population and pollution. Current methods of water treatment are impractical to apply in many parts of the world, as these technologies are expensive, require large facilities staffed by a litany of professionals, and the production/disposal of treatment chemicals that often have negative environmental impacts. The need to develop a method of water treatment that is less expensive, operates without the use of chemical treatments, and has relatively low electrical power usage is of profound importance. One of the most viable and promising optionsoptions is to make use both cavitation and ultraviolet light (UV). The purpose of this project is to develop a system for researching the combined effects of these two forms of water purification.
Cavitation occurs when the static pressure of water drops below vapor pressure. Small microbubbles form and slowly collapse in an energetic manner. As cavitation bubbles collapse, temperatures within the bubble can reach upwards of 5000 degrees Kelvin. Due to pyrolytic decomposition that takes place within the collapsing bubbles, the OH radicals and shock waves arecan be generated at the gasβliquid interface (A. Agarwal et al, 2011). These radicals degrade contaminants suspended within the water that would otherwise resist ultraviolet degradation. This makes cavitation a promising method of water treatment.
Ultra violet light is capable of killing bacteria and living contaminants in water. Short wavelength UV light, in the range of 10 nm to 400 nm, kills cells by interacting with their structures and disrupting DNA (NIOSH, 2008). UV light is capable of killing up to 99.99% of bacteria in clear water. This system of water purification is both cost effective and nontoxicchemical free but it cannot break down particle contaminants that bacteria tend to live in. However in combination with a particle filtration system, or in our case a cavitation system, UV reactors are simple to maintain, cost effective and chemical free.
The concise purpose of this teamβs senior design project will be to develop a fluid flow test apparatus to demonstrate the degree of effectiveness of the combination of UV radi.
Diffuser in Steam Vent Silencer By Using Computational Fluid DynamicsIJERA Editor
Β
Recently, research on new techniques for noise reduction of steam vent silencer has been addressed. However,
research work on shape optimization of steam vent silencer along with work on pressure drop has been sorely
neglected. Therefore, a numerical simulation has been investigated on the pressure drop using steam vent
silencer is introduced in this research work. This emphasizes the variation of pressure drop with the influence of
holes with various geometries like circular holes, square holes and square extrusion in pressurized inlet diffuser.
The sensitivity of pressure drop is less in square extrusion, compared to all other geometry. So it can conclude
that shape optimization of pressurized inlet diffuser in steam vent silencer is obtained with the application of
square extrusion.
Design and Analysis of Impregnation Chamber Used In Vacuum Pressure Impregnat...IOSR Journals
Β
The simple explanation is that in nature and in manufacturing, things leak. Vacuum impregnation
stops leak. The ultimate goal of vacuum impregnation is to seal leak/migration paths without impacting the
functional, assembly or appearance characteristics of a part. The impregnation chamber which is used in VPI
process operates maximum up to 80 to 150 psi.it is important to analyse and design the pressure vessel that will
provide safety, durability and serviceability to the company. Accomplishing this task will require a very good
understanding of behaviour and a good knowledge of parameters that affecting the pressure vessel due to
varying loads, pressure and thickness of shell element. The most important one is that the given geometry of
pressure vessel must be analysed to assure it should meet the design standards
Effect of spikes integrated to airfoil at supersonic speedeSAT Journals
Β
Abstract
The objective of this is to analyse the flow field over an aerofoil section integrated with spikes at supersonic speed (Mach number
greater than 1). Use of spike integrated with aerofoil changes the flow characteristics over aerofoil and hence aerodynamic lift
and drag. The experiment consists of flow visualization graphs and measurement of coefficient of aerodynamic drag and lift.
Here we are using different shapes of spike like sharp edge and hemi spherical edge. In this we will compare the flow over
aerofoil with spike and without spike. The flow analysis is done by using Computational fluid dynamics (CFD). CFD is the study
of external flow over a body or internal flow through the body. CFD is aiding aero-dynamist to better understand the flow physics
and in turn to design efficient models. In short, CFD is playing a strong role as a design tool as well as a research tool.
Keywords: NACA 651-412 airfoil, spike, Ansys Fluent, Ansys ICEM CFD, Pressure Coefficient
Numerical study of disk drive rotating flow structure in the cavityeSAT Journals
Β
Abstract
This paper aim in conducting the numerical simulation of laminar flow to explore disk-driven vortical flow structure of a cubical
container subjected to a disk rotation on the roof of the container in different Reynolds numbers to observe the flow structure and
the reason of vortical flow form. For this study, finite difference method with dispersion-relation- preserving (DRP) scheme is
dispersed governing equations space term, but adopt time term with TVD Runge-Kutta method. To add accuracy of numerical,
this thesis also uses topology theory to analyze the characteristic of singular point. Three-dimensional vertical flow is observed
flow structure and move to condition. The result to obtain Reynolds numbers to increase attracting spiral nodes increasingly
approaches the floor of the cavity. We have also depicted the vertical flow structure in terms of cortex cores which provide more
details about how change of the Reynolds number
Keywords: disk-driven, finite difference method, dispersion-relation-preserving (DRP), Runge-Kutta, topology theory
1. Omar Wannous
Pressure Loss Optimization of a Sprinkler
Valve
Helsinki Metropolia University of Applied Sciences
Bachelor of Engineering
Mechanical Engineering
Bachelorβs Thesis
29 May 2016
2. Abstract
Author(s)
Title
Number of Pages
Date
Omar Wannous
Pressure Loss Optimization of a Sprinkler Valve
85 pages + 6 appendices
29 May 2016
Degree Bachelor of Engineering
Degree Programme Mechanical Engineering
Specialisation option Energy and Environmental Engineering
Instructor(s)
Jarmo Helasuo, M.Sc. Engineering Manager
Tobias Immler, M.Sc. Product Development Engineer
Heikki Paavilainen, Senior Lecturer
The aim of this Bachelorβs thesis was to optimize the pressure loss for an already built
sprinkler valve for a high pressure water mist system. The purpose of optimizing the pres-
sure loss through the sprinkler valve is to gain better functionality characteristics for the
high pressure water mist system in both land and marine based applications.
In order to, obtain a good understanding of the high pressure water mist technology and
why it is preferred especially in marine applications, the conventional sprinkler system is
introduced and discussed briefly in the beginning. Also, the regulations and standards as
well as the classification societies are introduced for the high pressure water mist system.
It is important to develop a good understanding of fluid mechanics since it is widely used in
the design of modern engineering systems. Therefore, the fluid mechanics for internal flow
and the concepts regarding the pressure loss effects are discussed and explained com-
prehensively.
The research started by conducting an extensive feasibility study for a sprinkler valve, in
order to allocate the problem as well as to compare the results with the results obtained
from the development work. The experimental results unveiled the deviation of the theoret-
ical based results, and this was due to a simplified approach and hypotheses made in the-
ory.
The feasibility study resulted in several potential design concepts for the sprinkler valve,
which were simulated by utilizing the Computational Fluid Dynamics (CFD) approach.
Based on the obtained results from the simulation, one concept design was upgraded and
field tested in the sprinkler valve.
In conclusion, the scope of the project was achieved by the final concept design. The de-
velopment work concluded in high optimization level, which will in the future bring several
enhanced functionality properties for the water mist system.
Keywords Fluid mechanics, internal flow, pressure loss optimization,
sprinkler system, computational fluid dynamics
3. Contents
Acknowledgements
1 Introduction 1
1.1 Research Problem 2
1.2 Scope of Thesis 3
1.3 Limit of Research 4
2 Introduction to Water Mist 5
2.1 HI-FOG Water Mist and Fire Protection System 6
2.1.1 Range of Nozzle Types 7
2.2 Installation Systems 8
2.2.1 Wet Pipe Installation System 8
2.2.2 Dry Pipe Installation System 10
2.3 Classification Societies 12
3 Common Engineering Review for Fluid Mechanics 14
3.1 Viscous and Inviscid Regions of Flow 15
3.2 Overview to Cavitation 16
3.3 Mass and Volume Flow Rates 16
3.4 The Bernoulli Equation and its Limitations 18
3.5 Laminar and Turbulent Flow 20
3.5.1 Entry Regions and Lengths 21
3.6 Pressure drop and Minor Loss 23
4. Acknowledgements
Firstly, I would like to show my deepest gratitude for my parents who have supported
me throughout my studies and stood beside me every single moment. I also want to
thank my brothers for the immense support as well.
I would like to thank my project supervisor Jarmo Helasuo for giving me such an inter-
esting and challenging subject as well as for the precious advises throughout my thesis
work. I would like to thank especially Tobias Immler for the help and support as well as
for the valuable tips and advices and the wonderful experience. I also would like to
show my gratitude for the help and advices I received from the rest of the staff.
Finally, I would like to thank my work supervisor, senior lecturer Heikki Paavilainen, for
the advices and comments for my thesis work.
Helsinki 29.05.2016
Omar Wannous
5. 1
1 Introduction
Fluid mechanics has been an important topic for centuries for scientists since fluid
transportation plays a major part in various engineering applications. Archimedes was
the first to study fluid fundamentals by postulating the parallelogram law for addition of
vectors and the laws of buoyancy and applied them to floating and submerging objects.
There are also many other scientists who has contributed to the development of the
fluid flow engineering from which we benefit today. There are numerous applications
that comfort our daily life interactions which have developed by time into commonly
used inventions. The presence of fluid technology can be noticed in all kinds of trans-
portation systems, waste transport and treatment, power plant systems, pipelines,
crude oil and gas transfer, designing tall buildings and bridges. All technologies where
fluid dynamics is used cannot be all listed since there are so many different applica-
tions.
The basic concept of fluid is transporting the substance from place to another by ex-
ploiting its kinetic energy and transferring it to a form of mechanical energy.
Fluid flow studies are governed by two completely different substances, liquid and gas.
The study of liquid flow is called hydrodynamics. Liquid includes different kinds of sub-
stances such as oil and water chemical solutions. In most fluid flow applications water
is by far the most common liquid and respectively, most applications are involved in
hydrodynamic fluid control.
Studies of fluid are classified into two research regimes, external flow and internal flow.
External fluid flow studies concentrate on the behaviour of the flow and its profile on
external surfaces e.g. the wings of an airplane. Respectively, internal fluid flow studies
focus on the flowβs behaviour inside the control volume, for example in tubing systems.
Pressure loss, when transporting liquids in pipes, is indicated due to friction affect near
the wall of the pipe because of the no slip condition. In practice, the study of this physi-
cal phenomenon is divided into two approaches, analytical and experimental, after
which prototypes based on the obtained results are constructed and tested in laborato-
ries. The analytical approach is practised in two different ways, numerical or computa-
tional. The numerical method is to apply mathematical and physical laws and equations
6. 2
based on simplified hypotheses in which, it is more convenient to classify them on the
basis of fluid common characteristics to make the laws more feasible to study numeri-
cally. The computational analysis is implemented more in practise rather than the nu-
merical approach for studies because of the technicality and accuracy of the method.
Numerical solutions in highly demanding applications bring uncertainty to the results
depending on the hypotheses and approximations made. Therefore, computational
fluid dynamics, better known as CFD, is most likely to be applied to reduce uncertain-
ties and to simulate the fluid flow in the application. The numerical methods are inex-
pensive and fast, whereas the experimental method is more expensive and time con-
suming and sometimes it can be justified as impractical.
1.1 Research Problem
Marioff Corporation Oy high pressure tubing system is applied in various application
fields one of which is marine. It produces different kinds of pump units which come with
different sizes of electrical motors. Permissible pressure loss in the system is deter-
mined by the pressure of the pump unit and the water amount that pump unit has to
deliver to cover the most demanding section in the vessel. Essential component of the
high pressure tubing system is a sprinkler. Each sprinkler type has a validated operat-
ing pressure which it needs in order to operate in designed features, therefore, pres-
sure losses over the tubes has to be limited for achieving the validated operating pres-
sure of a sprinkler. Thus, pressure loss over every component in the tubing system has
to be controlled and especially valves which develops pressure losses the most, rela-
tively.
Pressure loss over the section valve is considerable in high volume flow rates. In some
cases, the pressure losses in the tubing system could exceed the permissible value
which in return requires enhancing the pump unit or installing bigger tubes. Conse-
quently, this might be a deal breaker for the company.
The research problem of this thesis is to reduce the pressure loss over the section
valve by modifying design features inside the valve in order to allow more accessible
path for the water to flow through. The water flow is assumed to go through an insuffi-
cient area between the piston and the body which consequently develops a huge pres-
sure drop in that certain area.
7. 3
1.2 Scope of Thesis
Introduction for fluid mechanics is to be discussed comprehensively e.g. Bernoulli
equation, common characteristics of laminar flow and turbulent flow, viscosity affect
and Darcy-Colebrook equation etc. HI-FOG high pressure water mist system will be
introduced generally as well as the operational principle of the HI-FOG system and its
applications. Also, the classification societies that governs on both land and marine
fields as well as the regulations and standards set by them are introduced. A compre-
hensive overview of the operational principle of the sprinkler section valve is discussed
as well as the interface design with water mist system.
In order to optimize the pressure loss over the sprinkler valve, a research study is con-
ducted for the current configuration design. Research will be carried out comprehen-
sively by using modern technical programs and well equipped test facilities. The results
obtained from research will be analysed and product development will be carried out
based on that. The aim is to optimize the pressure loss over the sprinkler valve, which
will in return improve to optimize the pressure level in the system.
The aim is to develop several potential solutions for the sprinkler valve. All the design
concepts will be studied and simulated, after which only the viable solutions will be up-
graded and manufactured for final testing. In the end, recommendations for future work
will be noted.
8. 4
1.3 Limit of Research
In terms of the theory part, the HI-FOG high pressure water mist system will be dis-
cussed on the general level without taking a stand of conventional sprinkler system
neither competitive solutions on the market. The basic concept of fluid mechanics will
be discussed only for internal flow inside a circular pipe leaving out open flow studies
and the characteristics of it. Classification societies will be introduced generally without
bringing up any classification centre in particular, given that referential context might be
noted from individual classification centre.
Due to installation purposes, any considerable redesigning to the valve body is not
permissible. Therefore, the research will only focus on the cartridge inside the sprinkler
valve. Primarily, the concentration in the development work will be either on redesign-
ing the piston or replacing the spring for much softer spring which consequently ena-
bles the water to flow over a bigger area. The research will not include any other com-
ponents of the HI-FOG system nor there will be cost analysis of the system.
9. 5
2 Introduction to Water Mist
The HI-FOG water mist and fire suppression system was established in the early
1990s. At present, the high pressure water mist fire suppression system competes with
other fire fighting systems such as conventional sprinkler and gas suppression sys-
tems.
The high pressure water mist fire suppression technology was initially developed after
Halon, which is a general name to a hydrocarbon in which one or more hydrogen at-
oms have been replaced by atoms from the halogen series as like bromine or chlorine,
were forbidden to be used in solid fire extinguishing systems due to their harmful im-
pact on the environment. A solid fire extinguishing system is a system that cannot be
replaced after installation /1/. In the early 1990s, IMO (International Maritime Organiza-
tion) ordered that new passenger vessels carrying more than 35 passengers should be
equipped with a sprinkler fire-fighting system or an equivalent corresponding system,
and it was also decided that by the year 2005 the hazardous fire extinguishing systems
of old vessels had to be upgraded to meet with the new regulations. /2/
The regulations set by IMO were considered very harsh because a conventional sprin-
kler fire extinguishing system demands very large pipes and thus more water. Conse-
quently, this upgrade brought more weight and unstableness to vessels that had to
improve their system. Thus, this point was considered a beginning for the high pres-
sure water mist fire suppression technology. One of the advantages that the high pres-
sure water mist suppression system brings is smaller pipes and lightness as well as
smaller water consumption in comparison with conventional sprinkler systems. The
main principle of the high pressure suppression system is that it sprays very small wa-
ter droplets, i.e. fog, unlike conventional sprinkler with big water droplets. In addition,
the high pressure water mist suppression system has a better extinguishing efficiency
than conventional sprinkler systems, which has been reached by downsizing the water
droplet size. /4/
A high pressure water mist system is defined by the water droplet size. The National
Fire Protection Association (NFPA 750) states that the water droplet size has to be less
than 1000 microns at the minimum operating pressure of the sprinkler in a high pres-
sure water mist system. System pressure in some high pressure water mist systems
can rise nearly up to 200 bar. In the high pressure water mist systems, the water mist
10. 6
coming out from an automatic activation sprinkler is achieved by high pressure water
flowing through multiple nozzle orifices. The out coming mist obtains high momentum
and it is extremely fine. /4/
2.1 HI-FOG Water Mist and Fire Protection System
Marioff water mist system was established at a time when the maritime industry was
looking for a replacement to a conventional sprinkler fire extinguishing system. The
founder of Marioff Corporation, GΓΆran Sundholm, responded to the needs of the indus-
try and introduced the high pressure water mist system which is known under the HI-
FOG brand. HI-FOG brand was launched in the early 1990s. /3/
Figure 1 illustrates the HI-FOG water mist and fire protection system.
Figure 1. Marioff high pressure water mist and fire protection system. A wet pipe installation
system.
The main components of Marioff high pressure water mist system are water supply,
pump unit, section valve and a sprinkler. The water is pumped from a water tank by the
pump unit into the high pressure pipes. The sprinklers are mounted behind every sec-
11. 7
tion valve. A section valve keeps the other section apart from each other, thus every
fire protected section in a marine based application or a land based application has its
own section valve. The sprinklers are mounted in the ceiling behind the section valve.
Sprinklers, section valves and pump units vary between marine application and land
applications. IMO has regulated the sections in marine application in regards to each
sections fire risk. Therefore, in marine applications components, for example, sprinklers
and section valves are designed to comply with the regulations set by IMO. The follow-
ing chapters will introduce the main characteristics of different nozzle types of Marioff
and two main installation systems.
2.1.1 Range of Nozzle Types
There are two types of sprinklers that are applied in a sprinkler system: automatic acti-
vation sprinklers and spray heads. /4/
An automatic activation sprinkler has a spraying head in which an activation element is
integrated. The activation element will discharge the sprinkler when it reaches a certain
temperature degree. The element can be, for example, an ampoule in which is a liquid
and a small air bubble. The ampoule explodes when it reaches the designed tempera-
ture, which consequently discharge the sprinkler. There are various range of ampoules
with a variable explosion temperature. The breaking temperature of an ampoule is cho-
sen on the basis of the demand of the protected application. /4/
In figure 2, two Marioff automatic activation sprinklers from different product range are
displayed.
Figure 2. Marioff automatic activation high pressure sprinklers. On the right is 2000-series
sprinkler type and on the left is 1000-series sprinkler type.
12. 8
A spray head is similar to an automatic activation sprinkler but without a discharge el-
ement in it. Figure 3 represents a model of spray head.
Figure 3. A model of Marioff many spray head types.
The amount of nozzles as well as the angle of the cone at the end of a spray head can
differ from a protected application to another.
2.2 Installation Systems
Sprinkler installation systems can be classified to four main installation groups from
which two mainly used are introduced in this chapter: wet pipe system and dry pipe
system. Other main installation types are pre-action systems and section release sys-
tems. In addition of the main installation systems, there are various installation meth-
ods that are in the end more or less manufacturers own designs. /4, 5/
Therefore, two main Marioff installation systems are introduced. Due to undesirable
information to be posted, installation systems are discussed in a general level.
2.2.1 Wet Pipe Installation System
In wet pipe installation, the pipe is filled in water up till the automatic activation sprinkler
in standby state, as shown in figure 1. The standby pressure depends upon the system
pressure class and the manufacturer. In case of fire, the generated heat breaks the
ampoule of the automatic activation sprinkler which, consequently discharges the
sprinkler. The water inside the pipe begins to flow through the sprinkler nozzles. Behind
each section valve can be numerous amounts of automatic activation sprinklers, never-
13. 9
theless the water flows through the discharged sprinklers and not necessarily from all
the mounted sprinklers. In wet pipe installation, there is a section valve which is de-
signed for the noted installation system. The section valve is normally open (NO) in
standby state and it is closed for maintenance purposes or stopping the water flow e.g.
after a fire. /4, 5/
Figure 4 illustrates a model of Marioff wet pipe system section valve.
Figure 4. A Marioff wet pipe system section valve
In case of fire, a pressure difference switch will indicate a pressure drop due to water
flow, which will send a signal to a local control panel. The control panel will set off an
indication of the section valve in the control panel, in order to notify a pressure drop in
that section. /4/
The wet pipe installation is the most utilized installation system. It has become popular
due to its simplicity and reliability as well. Because it is a simple technology, it is the
most cost saving installation system in terms of the purchase cost, installation cost and
service cost as well. The wet pipe installation system is faster to extinguish a fire com-
pared to other installation systems, that is because the pipe is filled with water all the
way up till the automatic activation sprinkler. /4, 6/
14. 10
The disadvantage of a wet pipe installation system is that they are not suitable as such
to sub-freezing environments. It is not applicable for applications which ambient tem-
perature may rise over 95 degrees Celsius as well. The system may leak if the piping
parts are objected to a severe damage during handling or installation. /4, 6, 7/
Wet pipe installation system is more applicable for a protected application which re-
quires an immediate start up. In general, suitable applications are therefore buildings,
hotels, factories, warehouses, office facilities and common spaces in vessels. Respec-
tively, it is not the most preferable solution for museums, libraries and facilities of elec-
tronics industry. /4/
2.2.2 Dry Pipe Installation System
Dry pipe sprinkler installation system uses automatic activation sprinklers and the pipe
is surrounded by air or inert gas, compare to wet pipe installation system. Figure 5
shows the schematic of a dry pipe system.
Figure 5. Machinery space system.
As shown in figure 5, the skeletal pipelines are filled with water in standby pressure.
The water in the skeletal pipelines is separated from the section pipelines by a dry pipe
system section valve. The section valve is remained closed by the pressurized air or
15. 11
the inert gas in the section pipeline, and it will open when the pressure in the dry pipe
section decreases to a certain pressure level. When the dry pipe section valve reaches
an opening pressure due to an activated sprinkler, the water begins to flow excessively
into the dry pipeline and it will come out from the discharged sprinkler. It is necessary
for the section valve to have some kind of detector attached to it, in order to indicate
the release of the valve and, thus locating the fire. /4, 8, 9/
The dry pipe installation system has to have an inert gas or a pressurized air source for
maintaining the pressure inside the dry pipe section. Usually, the system manufacturer
recommends the appropriate maintainable pressure level in the dry pipe section. The
pressure level is designed to sustain a minor leakage, thus the dry pipe section valve
does not open due to minor leakage. The source has to be dimensioned in such way,
in order for the system to activate in 60β90 second according to the industry standards.
As the activation is typically detected from a decreased gas pressure level, the activa-
tion time depends on the volume of the dry pipe section and the k-factors of the sprin-
klers. /4, 9, 10, 11, 12/
The great advantage of the dry pipe installation system is that the system is applicable
in applications of sub-freezing environments. The system is also applicable in sites
above 95 degrees Celsius. There are also some restrictions for the rest of the system.
The dry pipe section valve has to be installed in ambient temperature between 0β95
degrees Celsius. The dry pipe system is usually installed in cold stores, attics, loading
docks, garages and freezers. It is often presumed that dry pipe installation system
brings additional protection against accidental discharges, and thus they would be ap-
plicable for delicate protection sites e.g. museums or libraries. This is a misinterpreta-
tion, because the water in the dry pipe system will start flowing through the sprinkler
nozzles within a minute after the activation of the sprinkler. /4, 10, 11/
There is also disadvantages in dry pipe system that have to be taking into account
when choosing this particular installation type. The dry pipe installation system is more
complicated in comparison with the wet pipe installation system. Therefore, the dry
pipe installation system is more expensive, installation and service expenses are costly
as well. As noted earlier, systems activation time is longer (60β90 seconds) than the
wet pipe installation system. Any improvements for the system after the installation are
restricted. The dry pipe section has to be well dried off from water droplets in pursu-
ance of installation in order to avoid corrosion in pipes /4/. As a conclusion, the dry pipe
16. 12
system does not bring a clear advantage on the wet pipe system if the protected room
is within the appropriate temperature range of 5β95 degrees Celsius.
2.3 Classification Societies
Maritime safety is constantly being improved to prevent accidents and pollutions by
ships. Regulations regarding maritime are made by International Maritime Organization
(IMO) which is the United Nations (UN) specialized agency with responsibility for the
safety and security of shipping. Every vessel that has been built is registered under a
classification society. Classification societies are private agencies that establish and
update technical standards for construction and operation of ships as well as safety
standards. /13/
When a high pressure water mist system is designed, it is bear in mind that the system
has to pass a full scale fire test. Therefore, the entire system with its components has
to prove their undisputable performance. Marioff has conducted thousands of full scale
fire tests in order to prove the system efficiency in various applications and it has the
most class approvals in the entire water mist industry /4, 14/. In addition of fire tests,
most classification centres conduct separate tests for the system components. An
American insurance company FM (Factory Mutual) conducts tests for every critical
component in the system individually. Testing for a classification approval is a time
consuming process and expensive as well, and this is the reason of slow growing ap-
pearance in the market for water mist systems. /4, 15/
Important operational parameters of a water mist system are distance between sprin-
kler heads, operational pressure and installation height of the sprinkler. These parame-
ters are determined by the fire tests. The parameters which were agreed upon on and
the system has passed on, are not to be modified afterwards. The system cannot be
installed in a space with greater fire risk than the conditions it was tested in. The fire
tests reflect the worst case scenario of what could be a potential forthcoming fire in the
application. Other tests beside class society tests are based on standards. The system
is built according to standards references, for instance, distance between sprinkler
heads, installation height, sprinklers operational pressure etc. However, the latter fire
test method includes certain risks e.g. does customerβs ordered system comply with a
conducted test that is based on a certain standard. /4, 15/
17. 13
With standards, a neutral comparison is obtained between the authorities and the clas-
sification societies. Water mist standards are done by several authorities, including
IMO, NFPA (National Fire Protection Association), ISO (International Organization of
Standardization), UL (Underwriters Laboratories), VdS (Verband der Schadenversi-
chen) and CEN (European Committee for Standardization). In addition, every country
based local research centres gives their recommendations regarding installation and
operational method. In Finland, VTT (Valtion Teknillinen Tutkimuskeskus) is the re-
search centre. /4/
As earlier mentioned, IMO does set regulations regarding maritime safety and security,
however, it does not conduct fire tests neither gives approvals for the system. IMO is
the leader in developing standards for water mist systems in vessels. SOLAS (Safety of
Life At Sea) has listed IMOβs regulations and they have become SOLAS agreements
and resolutions. Installation guidance and regulations are given in SOLAS and FSS
Code (International Code for Fire Safety Systems) for equivalent sprinkler systems.
The operational principal of an equivalent sprinkler system has to comply with the reso-
lutions stated on SOLAS and this is a precondition for using the system. IMO has de-
veloped numerous fire test methods for an equivalent sprinkler system. It has deter-
mined comparison fire test methods for different fire risk sections in a vessel. In case of
the equivalent sprinkler system passes the preconditioned tests, it is then allowed to
replace the conventional sprinkler system. /4, 16, 17, 18/
18. 14
3 Common Engineering Review for Fluid Mechanics
Fluid mechanics deals with liquids and gases in motion and at rest. The fluid flow stud-
ies are classified as being internal or external, depending on whether the fluid flows in
a conduit or in an open space over a surface. In the beginning of a study, the system is
defined. The region outside the system is called surroundings and it is left out from the
studies as the interest concentrates upon the system. The surface of the imaginary line
which separates the system from its surroundings is called the boundary. The bounda-
ry of the system can be fixed or movable. The systems can be considered to be open
systems or closed systems. The classification is determined by the nature of the study,
whether the chosen system is a fixed mass or a volume in space. A closed system has
a fixed mass which does not fluctuate, in other words, the mass is constant throughout
the system boundary. But energy, in the form of heat and work, can cross the bounda-
ry. In addition, the volume of the closed system is not necessarily fixed. An open sys-
tem, or a control volume as it is often denoted for, is a selected region in space. A con-
trol volume retains a component or a device that involves a mass flow such as valves
or nozzles. The control volume can be fixed or it may involve a moving boundary. Mass
interactions as well as energy interactions may be involved. /19/
The terms steady and unsteady are frequently used in engineering. In the calculations
both terms imply different things. The term steady means that there is no change of
properties, velocity, temperature, etc., at a point with time. Respectively, the term un-
steady is the opposite of steady. /19, 20/
A flow is classified as being compressible or incompressible, depending on the level of
variation of density during flow. If the density remains nearly constant throughout the
control volume, the flow is classified as incompressible. In general, the densities of
liquids are essentially constant all the time, and thus the flow of liquids is typically in-
compressible. Therefore, liquids are referred to as incompressible substances. Com-
pressible substances are gases, for example, a small pressure change causes a
change in the density of atmospheric air. /19, 20/
19. 15
3.1 Viscous and Inviscid Regions of Flow
A fluid viscosity value informs the magnitude of a fluids internal resistance to the flow.
For instance, when two layers move relative to each other a friction force develops be-
tween them. The friction force develops at the contact surface and the direction of the
vector is opposite to motion. All fluids consist of internal resistance effects, however,
there are regions where the viscous effects are negligible, and they are called inviscid
flow regions. For example, a uniform fluid streams over a flat plate normal to the fluid
flow. The flat plate will separate the fluid as it hit the plate. The viscous affects are sig-
nificant near the plate and insignificant on both sides away from the plate. The viscous
and inviscid flow regions are shown in figure 6. /19/
Figure 6. The regions of viscous and inviscid flow over a flat plate normal to the fluid stream.
/19/
The velocity of a fluid stream near a stationary surface is zero, and this is because of
the no-slip condition. When a uniform fluid approaches a surface, the fluid motion
comes to a complete stop at the surface because the layer which is in direct contact
with the surface sticks to it and, hence, the velocity at the surface is zero. The velocity
profile, consequently, on the surface is not uniform anymore. Therefore, the flow region
adjacent to the wall in which the viscous effects are significant is called the boundary
layer. /19/
20. 16
3.2 Overview to Cavitation
Temperature and pressure are fluctuating properties for pure substances during phase-
change processes. The saturation temperature, also denoted as Tsat, is the tempera-
ture at which the pure substance begins to go under phase changes at given pressure.
Likewise, saturation pressure, also denoted as Psat, is the pressure at which the pure
substance starts to go under phase changes at given temperature. The vapour pres-
sure, usually denoted as Pv, is defined as βthe pressure exerted by its vapour in phase
equilibrium with its liquid at a given temperatureβ /19/.
The vapour pressure is an exclusive property for a pure substance and it is an equiva-
lent to the saturation pressure of the liquid (Pv = Psat). In liquid-flow systems, the pres-
sure of a liquid may drop below vapour pressure at some locations and result in unde-
sired vaporization. The vapour bubbles explode when they are swept away from the
low pressure regions, generating high pressure waves. This destructive explosion of
the vapour bubbles causes a drop in performance etc. This phenomenon is called cavi-
tation and it is commonly encountered in applications where impellers and pumps are
utilized. /19/
3.3 Mass and Volume Flow Rates
The conservation of mass principle for a control volume is simply, the net mass transfer
to or from a control volume during a time interval βt /19, 20/, and this expressed by:
πΜ ππ β πΜ ππ’π‘ = πΜ πΆπ
Μ (kg/s)
Where πΜ ππand πΜ ππ’π‘ are the total rates of mass flow into and out of the control volume,
and πΜ πΆπ is the rate of change within the boundaries of the control volume. During in
steady flow process the total amount of mass contained in the control volume does not
change with time. That is, the amount entering the control volume per unit time is equal
to the amount exiting the control volume per unit time /19, 10/. Thus, the conservation
of mass principle for a steady-flow system with multiple inlets and outlets is expressed
by:
β πΜππ = β πΜππ’π‘ (kg/s)
21. 17
The amount of mass flowing through a cross-section per unit time is called mass flow
rate, and it is denoted by πΜ . The dot over a symbol indicates a time rate of change. For
incompressible flow or even for compressible flow where the density is approximated to
be uniform across the cross-section are, the equation for mass flow rate becomes: /19,
20/
πΜ = πππ π£π π΄ π (kg/s)
Where π is the density of the substance [kg/m3
], Vavg is the average velocity across the
cross-section area [m/s] and Ac is the area of the cross-section [m2
]. The area of the
cross-section for pipes and ducts is expressed by:
π΄ π =
ππ2
4
(1)
The conservation of mass principal can be also expressed by volume flow rate for
steady incompressible flow:
β πΜππ = β πΜππ’π‘ (m3
/s)
The volume flow rate is expressed by:
πΜ = ππ π£π π΄ π (m3
/s) (2)
Where Vavg is the average velocity across the cross-section area, and Ac is the area of
the cross-section.
22. 18
3.4 The Bernoulli Equation and its Limitations
The Bernoulli equation gives an approximate relation between pressure, velocity and
elevation. The equation is applicable to steady and incompressible flow. The most
commonly used Bernoulli equation in fluid mechanics for steady, incompressible flow
along any two points on the same streamline in inviscid regions of flow /19, 21/, is ex-
pressed by:
π1
π
+
π1
2
2
+ ππ§1 =
π2
π
+
π2
2
2
+ ππ§2 (3)
Where P1 and P2 are the static pressure at the inlet and the outlet of the control volume
[Pa], V1 and V2 are the velocity at the inlet and the outlet of the control volume [m/s], g
is the acceleration of gravity [m/s2
], z1 is the reference elevation level [m], and z2 is the
elevation relative to the reference level [m].
The mechanical energy is the form of energy that can be converted to a mechanical
work completely by a mechanical device. The fluid systems are designed to transport
fluid from one location to another at specified flow rate, velocity and elevation. The sys-
tem may generate mechanical work in a turbine or it may consume mechanical work in
a pump. A turbine extracts mechanical energy from a fluid by dropping the pressure of
the fluid. Respectively, a pump transfers mechanical energy to a flowing fluid by raising
the pressure of the fluid. Flow energy expresses the amount of energy in a flowing flu-
id. /19, 21/
Therefore, it is convenient to express the mechanical energy of a flowing fluid by fluid
energy. Hence, the Bernoulli equation can be expressed as: π/π is the flow energy,
V2
/2 is the kinetic energy, and gz is the potential energy of the fluid. /19, 20, 21/
In order to make Bernoulli equation clear and visible in terms of the flow energy, each
term in the equation can be multiplied by the density π and it will yield to /19/:
π + π
π2
2
+ πππ§ = ππππ π‘πππ‘ (πππππ π‘βπ π π‘ππππππππ) (4)
Now, each term has pressure units, and thus each term represents some kind of pres-
sure: P is the static pressure, and it represents the actual thermodynamic pressure of
23. 19
the fluid, π
π2
2
is the dynamic pressure and it represents the pressure rise when the fluid
in motion is brought to a complete stop, and πππ§ is the hydrostatic pressure. /19/
The sum of the static pressure and dynamic pressure is called stagnation pressure.
The stagnation pressure represents the pressure at a point when the fluid in motion is
brought to a complete stop. It can be noted from the conservation of mass principle,
that when the flow area decreases the average velocity increases and vice versa. The
static pressure, respectively, decreases at the orifice. Vena contracta is the point where
the flow area reaches the minimum value. The Bernoulli equation (4) demonstrates the
balance between static, dynamic and hydrostatic pressure. When the stream of a flow
is level, there is no elevation differences, the hydrostatic pressure is assumed to be
constant along the streamline, thus, it can be eliminated from the equation. As the ve-
locity increases towards the vena contracta point the static pressure decreases. After
the vena contracta point, the fluid velocity decreases and the static pressure increases.
This phenomenon is called pressure recovery. The concept of vena contracta point is
shown in figure 7. /19, 21/
Figure 7. Static and dynamic pressure around vena contracta point. /21/
24. 20
Care must be exercised when applying the Bernoulli equation. The equation is one of
the most frequently used and misused because of the simplicity of the Bernoulli equa-
tion. In order to, make the Bernoulli equation applicable, some limitations and assump-
tions have to be made. The first limitation of the Bernoulli equation is that the flow has
to be a steady flow, negligible viscous effects, any shaft work is not considered, the
density of the fluid has to be approximated to be constant, incompressible flow, and the
Bernoulli equation is applicable along a streamline. /19, 21/
3.5 Laminar and Turbulent Flow
Fluid flow applications are comprehensively used in cooling applications and fluid dis-
tribution networks etc. The friction affect is directly proportional to the pressure drop
and head loss in pipes. In this regard, flow sections of circular cross section are re-
ferred as pipes. Pipes are widely used in fluid flow applications, especially when the
fluid is liquid. This is due to their ability to withstand high pressure differences between
the inside and the outside without affecting the measurements. At low velocities the
flow is smoothly streamlined and this characterization is called laminar. When the ve-
locity begins gradually to increase, the streamline of the flow starts to behave chaotical-
ly, a disordered motion, and this characterization is called turbulent. In between laminar
and turbulent phase, there is a development phase which is called transition. The tran-
sition phase is characterized as a mixture of laminar and turbulent flow affects. The
flow fluctuates between laminar and turbulent flow before it becomes fully turbulent. In
the 1880s Osborne Reynolds discovered that the flow regimes depend on the ratio of
inertial forces to viscous forces in the fluid, and afterwards each and every regime was
expressed by Reynolds number values. Under most practical conditions, the flow in
circular pipe is laminar for Reynolds number under 2300 and turbulent for over 4000.
The transitional flow is in between Reynolds number 2300 and 4000.Figure 8 shows
the flow regimes. /19, 20, 21/
25. 21
Figure 8. An outlining figure of laminar and turbulent flow regimes. /19/
Reynolds number is expressed for internal flow in a pipe as:
π e =
ππππ£π π·
π
(5)
Where π is the density [kg/m3
], Vavg is the average flow velocity [m/s], D is the diameter
of the pipe [m] and Β΅ is the dynamic viscosity [kg/m*s]. Reynolds number is a dimen-
sionless quantity.
3.5.1 Entry Regions and Lengths
The velocity profile at the entrance of the pipe is uniform. However, due to the no-slip
condition the fluid particles in the streamline next to the pipe wall come to a complete
stop. This layer causes the fluid particles in the adjacent streamline to slow down as a
result of friction. Thus, the velocity near the wall gradually decreases. In order to, keep
the mass flow rate constant through the pipe, the velocity in the middle section of the
pipe has to increase. Figure 9 shows the development of the velocity profile. /19, 20/
26. 22
Figure 9. The development of the velocity profile. /19/
The layer in which the effects of the viscous shearing forces are felt is called boundary
layer. The region in which the frictional effects are negligible and the velocity remains
constant radially, is called irrotational flow region. The boundary layer continues to in-
crease in the flow direction until it reaches the centre of the pipe. The region from the
pipe inlet to the point at which the velocity profile becomes fully developed is called the
hydrodynamic entrance region, and respectively the length of this region is called the
hydrodynamic entry length. The region beyond the hydrodynamic entrance region in
which the velocity profile remains fully developed is called hydrodynamically fully de-
veloped region. However, the flow is denoted by fully developed. /19, 20/
The hydrodynamic entry length is determined separately for laminar and turbulent flow
due to their different behaviour. For laminar flow the dimensionless hydrodynamic entry
length is determined as follows:
πΏβ,πππππππ
π·
β 0,05π e (6)
Where Lh, laminar is the hydrodynamic entry length for laminar flow, D is the nominal di-
ameter of the pipe and Re is the Reynolds number. The entry length for Reynolds
number 2300 is 115D /19, 20/. Respectively, for turbulent flow the dimensionless hy-
drodynamic entry length is approximated as:
πΏβ,π‘π’πππ’ππππ‘
π·
β 10 (7)
27. 23
The entry length for turbulent flow is much lower than the laminar flow, because turbu-
lent flow does not depend on the Reynolds number.
3.6 Pressure drop and Minor Loss
The pressure loss is expressed for all types of internal fully developed flows by /19/:
βππΏ = π
πΏ
π·
ππππ£π
2
2
(8)
Where βPL denotes for the pressure loss between two points in the streamline of the
flow [Pa], f is the Darcy friction factor and ππππ£π
2
/2 is the dynamic pressure. This equa-
tion expresses the pressure loss for fully developed laminar and turbulent flows and for
circular and non-circular pipes. /19/
For fully developed laminar flow in a pipe, the Darcy friction factor is expressed as /19/:
π =
64
π π
(9)
The friction factor in fully developed laminar pipe flow depends on the Reynolds num-
ber. However, the friction factor in fully developed turbulent pipe flow depends on the
Reynolds number as well but also on the relative roughness Ι/D, which is the ratio of
the mean height of roughness of the pipe to the pipe diameter /19/. The equation for
calculating the friction factor for fully turbulent pipe flow is called Colebrook equation,
which is named after Cyril F. Colebrook (1910β1997) /19/. The Colebrook equation:
1
β π
= β2,0 log(
π
π·
3,7
+
2,51
π πβ π
) (10)
Where Ι is the surface roughness of the pipe [mm]. Lewis F. Moody designed a dia-
gram, which is nowadays known as the Moody chart, see appendix 1. The Moody chart
represents the Darcy friction factor for pipe flow as a function the Reynolds number and
Ι/D over a wide range /19/. /19, 21/
Naturally, in a piping system the flow passes through bends, elbows, valves, expan-
sions, contractions etc. These components and designs induces the flow to separate,
28. 24
and thus developing more pressure loss in the system. However, the most remarkable
pressure loss comes from the straight sections of the piping system, and this is denot-
ed as major losses. Thus, the pressure loss which develops due to the components in
the piping system are called minor losses. The flow profile and behaviour inside a valve
and fittings is very hard to anticipate and complex to determine by theoretical analysis.
Therefore, minor losses are determined experimentally and, naturally the manufactur-
ers conduct such tests for their components. /19/
Minor losses are expressed in terms of the loss coefficient KL, defined as:
πΎπΏ =
β πΏ
π2
2π
(11)
Where hL is the additional irreversible head loss caused by insertion of the com-
ponent and it is defined as hL = βP/πg /19/.
In general, the loss coefficient strongly depends on the Reynolds number and the ge-
ometry of the component.