This document is a service manual for tractor models TD4.70F, TD4.80F, and TD4.90F. It contains sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, steering, electrical systems, and cab, bodywork, and decals. The manual provides maintenance and repair instructions for technicians and warns of safety precautions to prevent accidents in the workshop.
This document provides an overview of the operation of a SIPART PS2 pressure control device. It includes a view of the device labeling the main components. The document then provides a table that defines the functions and settings of 55 parameters that can be configured on the device. The parameters relate to functions like the type of actuator, initialization settings, setpoint settings, alarm settings, and resetting to factory defaults. It also provides information on automatic initialization processes and potential error messages that could display.
El documento compara diferentes estándares de seguridad aplicables a hornos, calderas y calderas de recuperación. Describe los principios de seguridad funcional, incluyendo la separación de sistemas, la condición segura ante falla y la prohibición de bypass. También analiza los enfoques prescriptivos versus basados en el desempeño, señalando que los estándares basados en riesgo ofrecen mayor flexibilidad pero requieren un análisis minucioso de riesgos.
The document provides an overview of hydraulic systems, including:
1. It defines a hydraulic system as using pressurized fluid to perform work based on Pascal's Law of uniform pressure transmission.
2. It explains key hydraulic components like pumps, motors, valves and cylinders used to control flow and pressure.
3. It outlines the basics of open and closed loop systems and some common hydraulic symbols.
4. It identifies potential hazards like heat, flammability and high pressure failures that require safety precautions when working with hydraulic systems.
SCADA systems are used to monitor and control industrial processes that occur across geographically dispersed locations. They involve remote terminal units collecting field data and sending it back to a central control room via a communications system. This enables operators to view real-time data and remotely control processes from a central location for more efficient, reliable and safer operations. Common applications of SCADA systems include power generation and distribution, manufacturing, water and waste management, and buildings.
Teks tersebut merangkum tentang sistem bahan bakar common rail pada kendaraan diesel. Secara singkat, common rail adalah sistem injeksi bahan bakar modern yang menggunakan pipa rel untuk menyalurkan dan mengatur tekanan bahan bakar secara elektronik. Komponen utamanya terdiri atas pompa tekanan tinggi, pipa rel, injektor, dan ECU beserta sensor-sensor yang mengontrol proses injeksi secara presisi. Teks tersebut juga menjelaskan cara
John deere 6200 tractors service repair technical manual (tm4493)fujjsefksekmem
This document provides instructions for adjusting the shift mechanism on tm4493 tractors from 6100 to 6600 models. It involves the following steps:
1. Place the shifter shafts in the neutral position.
2. Adjust the shifter forks using threaded pins until they are centered in relation to the shift collars.
3. Move the shifter forks to all positions and ensure smooth shifting without binding or overlap between positions. Tighten locknuts on threaded pins to complete the adjustment.
Medical gases. piped and cylinder -trainingmillwallmarine
This document provides training on medical gases, including piped and cylinder gases. It aims to define medical gases, identify those commonly used and their applications, explain hazard warnings and safety information, and how to safely move and store gas cylinders. Key medical gases discussed are oxygen and entonox. The document outlines the reasons training is required according to various acts and policies. It also details safety information found on cylinder collars, types of cylinders and flow meters, and the different piped gases including oxygen, air, and suction. The training emphasizes remembering gas types and uses, safely moving and storing cylinders, and identifying safety information.
This document provides an overview of the operation of a SIPART PS2 pressure control device. It includes a view of the device labeling the main components. The document then provides a table that defines the functions and settings of 55 parameters that can be configured on the device. The parameters relate to functions like the type of actuator, initialization settings, setpoint settings, alarm settings, and resetting to factory defaults. It also provides information on automatic initialization processes and potential error messages that could display.
El documento compara diferentes estándares de seguridad aplicables a hornos, calderas y calderas de recuperación. Describe los principios de seguridad funcional, incluyendo la separación de sistemas, la condición segura ante falla y la prohibición de bypass. También analiza los enfoques prescriptivos versus basados en el desempeño, señalando que los estándares basados en riesgo ofrecen mayor flexibilidad pero requieren un análisis minucioso de riesgos.
The document provides an overview of hydraulic systems, including:
1. It defines a hydraulic system as using pressurized fluid to perform work based on Pascal's Law of uniform pressure transmission.
2. It explains key hydraulic components like pumps, motors, valves and cylinders used to control flow and pressure.
3. It outlines the basics of open and closed loop systems and some common hydraulic symbols.
4. It identifies potential hazards like heat, flammability and high pressure failures that require safety precautions when working with hydraulic systems.
SCADA systems are used to monitor and control industrial processes that occur across geographically dispersed locations. They involve remote terminal units collecting field data and sending it back to a central control room via a communications system. This enables operators to view real-time data and remotely control processes from a central location for more efficient, reliable and safer operations. Common applications of SCADA systems include power generation and distribution, manufacturing, water and waste management, and buildings.
Teks tersebut merangkum tentang sistem bahan bakar common rail pada kendaraan diesel. Secara singkat, common rail adalah sistem injeksi bahan bakar modern yang menggunakan pipa rel untuk menyalurkan dan mengatur tekanan bahan bakar secara elektronik. Komponen utamanya terdiri atas pompa tekanan tinggi, pipa rel, injektor, dan ECU beserta sensor-sensor yang mengontrol proses injeksi secara presisi. Teks tersebut juga menjelaskan cara
John deere 6200 tractors service repair technical manual (tm4493)fujjsefksekmem
This document provides instructions for adjusting the shift mechanism on tm4493 tractors from 6100 to 6600 models. It involves the following steps:
1. Place the shifter shafts in the neutral position.
2. Adjust the shifter forks using threaded pins until they are centered in relation to the shift collars.
3. Move the shifter forks to all positions and ensure smooth shifting without binding or overlap between positions. Tighten locknuts on threaded pins to complete the adjustment.
Medical gases. piped and cylinder -trainingmillwallmarine
This document provides training on medical gases, including piped and cylinder gases. It aims to define medical gases, identify those commonly used and their applications, explain hazard warnings and safety information, and how to safely move and store gas cylinders. Key medical gases discussed are oxygen and entonox. The document outlines the reasons training is required according to various acts and policies. It also details safety information found on cylinder collars, types of cylinders and flow meters, and the different piped gases including oxygen, air, and suction. The training emphasizes remembering gas types and uses, safely moving and storing cylinders, and identifying safety information.
This document discusses different types of hydraulic pressure control valves. It describes pressure relief valves, pilot operated relief valves, sequence control valves, and other types. Pressure relief valves limit pressure by diverting fluid to the reservoir when pressure reaches a set point. Pilot operated relief valves use a piston or spool controlled by a pilot valve. Sequence valves provide flow to a second actuator after the first reaches a threshold pressure. The document also provides examples of applications for different valve types.
This document discusses different types of hydraulic valves and components. It covers pressure control valves like relief valves, reducing valves, and unloading valves. It also covers direction control valves like check valves, 3/2 valves, 4/2 valves, and 5/2 valves. Additionally, it discusses flow control valves, manual and pilot operated valves, poppet and spool valves, actuators, pipes and hoses, fittings, seals, accumulators, and pressure boosters.
The document provides an overview of a Siemens S7-200 PLC training course. It discusses the history and advantages of PLCs over classical control systems. It then outlines the course contents which include introductions to PLC hardware configuration, programming languages, instructions like logic, timers, counters, and memory types. It also provides examples of programming concepts like inputs, outputs, timers, and counters.
This document describes different types of valves including a manually actuated three-position valve, a four-way two-position valve, and a spring-centered three-position valve. It also discusses a typical solenoid controlled, pilot operated or two-stage valve where the pilot choke is mounted on the valve.
El documento describe diferentes tipos de válvulas neumáticas e hidráulicas, incluyendo válvulas de bloqueo, flujo, presión, estranguladoras, limitadoras de presión, reguladoras de presión y selectores. Las válvulas cumplen funciones como distribución de caudal, regulación de flujo, retención, cierre, secuencia y escape rápido.
La neumática es la ciencia que estudia los movimientos, aplicaciones y procesos del aire. Un sistema de aire comprimido consiste en varios elementos como compresores, tratamiento, distribución y almacenamiento que trabajan juntos para generar, tratar y suministrar aire a presión a los puntos de consumo de una planta de manera eficiente. El diseño de un sistema de aire comprimido requiere determinar los requerimientos de consumo, presión y calidad de aire en cada punto, así como dimensionar la capacidad de generación para satisf
This document describes the closed loop control system used for boiler drum level control. It uses a three element control approach with drum level, feedwater flow, and main steam flow as process variables. During startup, a single 30% capacity feedwater control valve (FCV-101) is used to maintain drum level setpoint. At 30% load, control switches to two 100% capacity main feedwater valves (FCV-102) controlled via a three element algorithm. Drum level is measured by three level transmitters and averaged for input to the level controller (LIC-101). The controller output is summed with steam flow and used to set the remote setpoint for FIC-101, which controls FCV-102 position
1) As bombas hidráulicas convertem energia mecânica em energia hidráulica, criando pressão para mover fluidos através de sistemas.
2) Bombas são classificadas como hidrodinâmicas ou hidrostáticas, sendo estas últimas mais comumente usadas em sistemas industriais devido à pressão constante.
3) A cavitação e aeração podem ocorrer se a pressão de sucção for muito baixa, danificando a bomba através da formação de bolhas no fluido.
Unit ini membahas masalah-masalah utama dalam sistem hidraulik seperti kesan beban dan kelajuan berlebihan pada pompa yang dapat mengurangkan umur komponen, masalah peronggaan akibat pengendalian yang tidak tepat, kebocoran sistem, dan masalah pada silinder seperti kebocoran dan kelambatan gerakan. Dokumen ini juga menjelaskan panduan untuk memilih cairan hidraulik yang ideal berdasarkan sifatnya se
This report is an overview of available standards (IEC, ISO, EN and other standards) applicable within physical asset and maintenance management projects.
The standards are not described in detail, purpose of this document is to list a set of standards (including a short description) relevant for asset, engineering and maintenance management projects. The interested reader should check the details in the standard(s) itself.
Skirt support for vertical vessal 16 06,07,08,09Shahrukh Vahora
This document discusses the design of skirt supports for vertical vessels. Skirt supports are cylindrical shell sections welded to the outside of a vessel shell to provide structural support. They are well-suited for vessels subjected to wind, seismic, and other loads. The document describes how skirt height is determined based on NPSH requirements and is usually around 2.5 meters. It also discusses stress analysis of the skirt shell and design considerations for the bearing plate and bolting system, including the use of angle or ring bearing plates and centered or external bolting chairs depending on plate thickness.
Slide ini akan menunjukkan anda sebanyak sedikit contoh untuk memulakan kerja projek akhir tahun :) Semoga slide ini boleh memanfaatkan kepada yang memerlukan. Lmao
Cavitation occurs in pumps when the local pressure drops below the vapor pressure of the liquid being pumped, causing vapor bubbles to form. These bubbles grow until the pressure increases and causes them to rapidly collapse. This collapse creates shockwaves that can cause damage to pump components over time. To avoid cavitation, the net positive suction head available (NPSHA) must exceed the pump's required NPSH (NPSHR), accounting for suction pressure, elevation, and friction losses. Symptoms of cavitation include noise, vibration, reduced flow and pressure, and pitting wear of impellers and casings.
The AP pneumatic positioner from Kinetrol combines smooth and accurate mechanical positioning technology with convenient design features. It uses a proportional spool valve and force balance mechanism to precisely control actuators. The positioner is robust and adaptable, with options for high flow valves, housing styles, position monitoring, and I/P converters. It provides reliable, industrial-grade performance for process control applications.
Preventive Maintenance for CP by Eng. Amer HamdanEng. Amer Hamdan
This document provides an introduction and recommendations for a preventative maintenance program for centrifugal pump systems. It outlines key issues found during inspections of pumps and components. A preventative maintenance schedule is proposed to monitor pumps daily and monthly to check for issues like leaks, noise, vibration and performance deviations. Quarterly and yearly checks of additional parameters are also included to reduce failures and maintenance costs by 35-40% through early detection and resolution of problems. Regular cleaning, inspections, and system analysis are emphasized to protect pumps and extend their useful lifetimes.
New holland td4040 f tractor service repair manualfhjsekfksemert
This document is a service manual that provides specifications and repair instructions for tractors models TD4020F, TD4030F, and TD4040F. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and drawbars, steering, electrical systems, and the cab. The manual provides international symbols used on tractor components and safety rules for technicians performing maintenance and repairs.
New holland td4020 f tractor service repair manualpfiskdmjekm
This document is a service manual that provides information for servicing and repairing tractors models TD4020F, TD4030F, and TD4040F. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and drawbars, steering, electrical systems, and the cab, bodywork, and decals. The manual provides part numbers, specifications, and repair instructions for maintenance and repairs. Safety rules and symbols used in the manual are defined at the beginning.
This document discusses different types of hydraulic pressure control valves. It describes pressure relief valves, pilot operated relief valves, sequence control valves, and other types. Pressure relief valves limit pressure by diverting fluid to the reservoir when pressure reaches a set point. Pilot operated relief valves use a piston or spool controlled by a pilot valve. Sequence valves provide flow to a second actuator after the first reaches a threshold pressure. The document also provides examples of applications for different valve types.
This document discusses different types of hydraulic valves and components. It covers pressure control valves like relief valves, reducing valves, and unloading valves. It also covers direction control valves like check valves, 3/2 valves, 4/2 valves, and 5/2 valves. Additionally, it discusses flow control valves, manual and pilot operated valves, poppet and spool valves, actuators, pipes and hoses, fittings, seals, accumulators, and pressure boosters.
The document provides an overview of a Siemens S7-200 PLC training course. It discusses the history and advantages of PLCs over classical control systems. It then outlines the course contents which include introductions to PLC hardware configuration, programming languages, instructions like logic, timers, counters, and memory types. It also provides examples of programming concepts like inputs, outputs, timers, and counters.
This document describes different types of valves including a manually actuated three-position valve, a four-way two-position valve, and a spring-centered three-position valve. It also discusses a typical solenoid controlled, pilot operated or two-stage valve where the pilot choke is mounted on the valve.
El documento describe diferentes tipos de válvulas neumáticas e hidráulicas, incluyendo válvulas de bloqueo, flujo, presión, estranguladoras, limitadoras de presión, reguladoras de presión y selectores. Las válvulas cumplen funciones como distribución de caudal, regulación de flujo, retención, cierre, secuencia y escape rápido.
La neumática es la ciencia que estudia los movimientos, aplicaciones y procesos del aire. Un sistema de aire comprimido consiste en varios elementos como compresores, tratamiento, distribución y almacenamiento que trabajan juntos para generar, tratar y suministrar aire a presión a los puntos de consumo de una planta de manera eficiente. El diseño de un sistema de aire comprimido requiere determinar los requerimientos de consumo, presión y calidad de aire en cada punto, así como dimensionar la capacidad de generación para satisf
This document describes the closed loop control system used for boiler drum level control. It uses a three element control approach with drum level, feedwater flow, and main steam flow as process variables. During startup, a single 30% capacity feedwater control valve (FCV-101) is used to maintain drum level setpoint. At 30% load, control switches to two 100% capacity main feedwater valves (FCV-102) controlled via a three element algorithm. Drum level is measured by three level transmitters and averaged for input to the level controller (LIC-101). The controller output is summed with steam flow and used to set the remote setpoint for FIC-101, which controls FCV-102 position
1) As bombas hidráulicas convertem energia mecânica em energia hidráulica, criando pressão para mover fluidos através de sistemas.
2) Bombas são classificadas como hidrodinâmicas ou hidrostáticas, sendo estas últimas mais comumente usadas em sistemas industriais devido à pressão constante.
3) A cavitação e aeração podem ocorrer se a pressão de sucção for muito baixa, danificando a bomba através da formação de bolhas no fluido.
Unit ini membahas masalah-masalah utama dalam sistem hidraulik seperti kesan beban dan kelajuan berlebihan pada pompa yang dapat mengurangkan umur komponen, masalah peronggaan akibat pengendalian yang tidak tepat, kebocoran sistem, dan masalah pada silinder seperti kebocoran dan kelambatan gerakan. Dokumen ini juga menjelaskan panduan untuk memilih cairan hidraulik yang ideal berdasarkan sifatnya se
This report is an overview of available standards (IEC, ISO, EN and other standards) applicable within physical asset and maintenance management projects.
The standards are not described in detail, purpose of this document is to list a set of standards (including a short description) relevant for asset, engineering and maintenance management projects. The interested reader should check the details in the standard(s) itself.
Skirt support for vertical vessal 16 06,07,08,09Shahrukh Vahora
This document discusses the design of skirt supports for vertical vessels. Skirt supports are cylindrical shell sections welded to the outside of a vessel shell to provide structural support. They are well-suited for vessels subjected to wind, seismic, and other loads. The document describes how skirt height is determined based on NPSH requirements and is usually around 2.5 meters. It also discusses stress analysis of the skirt shell and design considerations for the bearing plate and bolting system, including the use of angle or ring bearing plates and centered or external bolting chairs depending on plate thickness.
Slide ini akan menunjukkan anda sebanyak sedikit contoh untuk memulakan kerja projek akhir tahun :) Semoga slide ini boleh memanfaatkan kepada yang memerlukan. Lmao
Cavitation occurs in pumps when the local pressure drops below the vapor pressure of the liquid being pumped, causing vapor bubbles to form. These bubbles grow until the pressure increases and causes them to rapidly collapse. This collapse creates shockwaves that can cause damage to pump components over time. To avoid cavitation, the net positive suction head available (NPSHA) must exceed the pump's required NPSH (NPSHR), accounting for suction pressure, elevation, and friction losses. Symptoms of cavitation include noise, vibration, reduced flow and pressure, and pitting wear of impellers and casings.
The AP pneumatic positioner from Kinetrol combines smooth and accurate mechanical positioning technology with convenient design features. It uses a proportional spool valve and force balance mechanism to precisely control actuators. The positioner is robust and adaptable, with options for high flow valves, housing styles, position monitoring, and I/P converters. It provides reliable, industrial-grade performance for process control applications.
Preventive Maintenance for CP by Eng. Amer HamdanEng. Amer Hamdan
This document provides an introduction and recommendations for a preventative maintenance program for centrifugal pump systems. It outlines key issues found during inspections of pumps and components. A preventative maintenance schedule is proposed to monitor pumps daily and monthly to check for issues like leaks, noise, vibration and performance deviations. Quarterly and yearly checks of additional parameters are also included to reduce failures and maintenance costs by 35-40% through early detection and resolution of problems. Regular cleaning, inspections, and system analysis are emphasized to protect pumps and extend their useful lifetimes.
New holland td4040 f tractor service repair manualfhjsekfksemert
This document is a service manual that provides specifications and repair instructions for tractors models TD4020F, TD4030F, and TD4040F. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and drawbars, steering, electrical systems, and the cab. The manual provides international symbols used on tractor components and safety rules for technicians performing maintenance and repairs.
New holland td4020 f tractor service repair manualpfiskdmjekm
This document is a service manual that provides information for servicing and repairing tractors models TD4020F, TD4030F, and TD4040F. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and drawbars, steering, electrical systems, and the cab, bodywork, and decals. The manual provides part numbers, specifications, and repair instructions for maintenance and repairs. Safety rules and symbols used in the manual are defined at the beginning.
New holland td4030 f tractor service repair manualfhjsekfksemert
This document is a service manual that provides specifications and repair instructions for tractors models TD4020F, TD4030F, and TD4040F. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and drawbars, steering, electrical systems, and the cab. The manual provides international symbols used on tractor components and safety rules for technicians performing maintenance and repairs.
New holland tv145 tractor service repair manualudfujjsejkkem
This document provides a table of contents for a repair manual for a TV145 tractor. The table of contents lists numerous sections, numbered 00 through 88, that cover various systems of the tractor like the engine, transmission, axles, brakes, hydraulics and more. Each section contains multiple chapters that go into further detail. The document also provides general safety and operational considerations for working on the tractor.
New holland tv145 tractor service repair manualkfdjkskdmm
This document provides a table of contents for a repair manual for a TV145 tractor. It lists over 30 sections and chapters that will be included in the manual, covering topics like the engine, transmissions, axles, brakes, hydraulics, wheels, ballasting, frames, climate control, electrical systems, accessories, and the cab. The sections and chapters are organized by book number, section number, and chapter number for easy reference to the specific information needed when repairing components of the tractor.
New holland tv145 tractor service repair manualfujskefksmem
This document provides a table of contents for a repair manual for a TV145 tractor. It lists over 30 sections and chapters that will be included in the manual, covering topics like the engine, transmissions, axles, brakes, hydraulics, wheels, ballasting, frames, climate control, electrical systems, accessories, and the cab. The sections and chapters are organized by book number, section number, and chapter number for easy reference to the specific information needed when repairing components of the tractor.
New Holland 8670 8770 8870 8970 Tractor Workshop Service Repair Manual.pdfExcavator
New Holland 8670 8770 8870 8970 Tractor Workshop Service Repair Manual
This service manual is a treasure trove of information, meticulously compiled to cover every aspect of the Bobcat M-970 Skid Steer Loader's service and maintenance. From the engine to the hydraulics, electrical systems to preventive maintenance, it leaves no stone unturned. This comprehensive coverage ensures that both seasoned technicians and novice operators have the guidance they need to keep the loader in prime condition.
General Maintenance
Troubleshooting
Engine Service / Repair
Transmission Service / Repair
Brake System
Wiring Diagram
Electrical System
Suspension
Periodic Lubrication
Steering
Cooling System
Fuel Injection / Fuel System
Emission System
Heater/ Air Conditional
Engine Control System
Chassis / Body
Restraint System
Interior
Differential / Drive
Axle.
John deere 4400 compact utility tractor service repair manualfusfejskekem
This technical manual provides specifications, operation descriptions, troubleshooting information, and repair procedures for Deere compact utility tractors models 4200, 4300, and 4400. The manual is organized by system, with sections covering specifications, component locations, schematics, theory of operation, troubleshooting, diagnostics, tests and adjustments, and repair. It is intended to help experienced technicians service and repair these tractor models. Safety information is provided throughout, including warnings about high pressure fluids, battery explosions, and safe servicing practices.
John deere 4200 compact utility tractor service repair manualfujsjefjskekmem
This technical manual provides specifications, operation instructions, troubleshooting information, and repair procedures for John Deere 4200, 4300, and 4400 compact utility tractor diesel engines. The manual is organized into sections covering specifications, theory of operation for fuel, cooling, and lubrication systems, troubleshooting charts, tests and adjustments for components like valves and injection pumps, and repair procedures for engine overhaul. Safety information is provided throughout, including hazards from high pressure fluids, battery explosions, and working in confined spaces.
John deere 4400 compact utility tractor service repair manualfjjskekdmmem
This technical manual provides specifications, operation descriptions, troubleshooting information, testing procedures, and repair instructions for John Deere 4200, 4300, and 4400 compact utility tractor diesel engines. The manual is organized into sections covering specifications, theory of operation for fuel, cooling, and lubrication systems, troubleshooting charts, engine system diagnostics, testing and adjustment procedures, and engine repair procedures. It is intended to help experienced technicians service and repair these diesel engines.
John deere 4400 compact utility tractor service repair manualudjjjskekdmm
This technical manual provides specifications, operation descriptions, troubleshooting information, and maintenance procedures for diesel engines used in John Deere compact utility tractors. It begins with an introduction and table of contents. The safety section outlines important safety information including handling batteries, high pressure fluids, and safe work practices. The manual is intended for experienced technicians and contains detailed information on engine systems organized by topic.
John deere 4400 compact utility tractor service repair manualfhhsjdkmem
This technical manual provides specifications, operation instructions, troubleshooting information, and repair procedures for John Deere 4200, 4300, and 4400 compact utility tractor diesel engines. The manual is organized into sections covering specifications, theory of operation for fuel, cooling, and lubrication systems, troubleshooting charts, tests and adjustments for components like valves and injection pumps, and repair procedures for engine overhaul. Safety information is provided throughout, including hazards from high pressure fluids, battery explosions, and working in confined spaces.
John deere 4200 compact utility tractor service repair manualfhhsjdkmem
This technical manual provides specifications, operation instructions, troubleshooting information, and repair procedures for John Deere 4200, 4300, and 4400 compact utility tractor diesel engines. The manual is organized into sections covering specifications, theory of operation for fuel, cooling, and lubrication systems, troubleshooting charts, tests and adjustments for components like valves and injection pumps, and repair procedures for engine overhaul. Safety information is provided throughout, including hazards from high pressure fluids, battery explosions, and working in confined spaces.
John deere 4400 compact utility tractor service repair manualfujsjefjskekmem
This technical manual provides specifications, operation descriptions, troubleshooting information, and repair procedures for Deere compact utility tractors models 4200, 4300, and 4400. The manual is organized by system, with sections covering specifications, component locations, schematics, theory of operation, troubleshooting, diagnostics, tests and adjustments, and repair. It is intended to help experienced technicians service and repair these tractor models. Safety information is provided throughout, including warnings about high pressure fluids, battery explosions, and safe servicing practices.
John deere 4200 compact utility tractor service repair manualfjjskekdmmem
This technical manual provides specifications, operation instructions, troubleshooting information, and repair procedures for John Deere 4200, 4300, and 4400 compact utility tractor diesel engines. The manual is organized into sections covering specifications, theory of operation for fuel, cooling, and lubrication systems, troubleshooting charts, tests and adjustments for components like valves and injection pumps, and repair procedures for engine overhaul. Safety information is provided throughout, including hazards from high pressure fluids, battery explosions, and working in confined spaces.
John deere 4300 compact utility tractor service repair manualfusfejskekem
This technical manual provides specifications, operation descriptions, troubleshooting information, and repair procedures for Deere compact utility tractors models 4200, 4300, and 4400. The diesel engine section covers specifications, theory of operation for fuel/air, cooling, and lubrication systems, a troubleshooting chart, diagnostics procedures, and tests/adjustments for items like cylinder compression, valve clearance, bearing clearances, and more. Safety information is also included to warn technicians of hazards involved in engine repair work.
Similar to New holland td4.70 f tractor service repair manual (16)
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 l excavator (prefix 5ym) service repair manual (5ym00001 ...fjsjekdmmeme
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 b ln excavator (prefix 5lr) service repair manual (5lr000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the component locations and assembly sequences.
Caterpillar cat 330 b ln excavator (prefix 3yr) service repair manual (3yr000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjsjekdmmeme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, bolts, and using a lifting device due to the head's weight of 95 kg.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar cat 315 c excavator (prefix cfl) service repair manual (cfl00001 ...fjsjekdmmeme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) It details 21 steps for disassembly, including removing gears, shafts, seals, and housing components.
3) The 19 steps for assembly describe installing these same parts in reverse order, with notes on cleaning, lubricating, and using various tools to set proper torque and clearance.
Caterpillar cat 311 c u excavator (prefix pad) service repair manual (pad0000...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c u excavator (prefix cke) service repair manual (cke0000...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjsjekdmmeme
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate
2. Camshaft
3. Camshaft bearings
4. Connecting rod bearings
5. Crankshaft main bearings
The instructions describe each removal and installation step in detail and include notes about proper procedure, tool usage, torque specifications and checks to perform.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
7. INTRODUCTION
International symbols
As a guide to the operation of the machine, various universal symbols have been utilized on the instruments, controls,
switches, and fuse box. The symbols are shown below with an indication of their meaning.
Thermostart
starting aid
Radio PTO
Position
Control
Alternator
charge
Keep alive
memory
Transmission
in neutral
Draft
Control
Fuel level Turn signals
Creeper
gears
Accessory
socket
Automatic
Fuel shut-off
Turn signals
-one trailer
Slow or
low setting
Implement
socket
Engine speed
(rev/min x 100)
Turn signals
-two trailers
Fast or high
setting
%age
slip
Hours recorded
Front wind-
screen
wash/wipe
Ground
speed
Hitch raise
(rear)
Engine oil
pressure
Rear wind-
screen
wash/wipe
Differential
lock
Hitch lower
(rear)
Engine coolant
temperature
Heater temp-
erature control
Rear axle
oil tem-
perature
Hitch height
limit (rear)
Coolant
level
Heater fan
Transmission
oil pressure
Hitch height
limit (front)
Tractor lights Air conditioner
FWD
engaged
Hitch dis-
abled
Headlamp
main beam
Air filter
blocked
FWD dis-
engaged
Hydraulic and
transmission
filters
Headlamp
dipped beam
Parking
brake
Warning!
Remote
valve extend
Work lamps
Brake fluid
level
Hazard
warning lights
Remote
valve retract
Stop
lamps
Trailer
brake
Variable
control
Remote
valve float
Horn
Roof
beacon
Pressurised!
Open carefully
Malfunction!
See Operator's
Manual
Warning !
Corrosive
substance
Malfunction!
(alter-
native symbol)
47913129 19/12/2016
3
8. INTRODUCTION
Safety rules
IMPORTANT NOTICE
All maintenance and repair operations described in this manual should be carried out exclusively by authorised work-
shops. All instructions should be carefully observed and special equipment where indicated should be used.
Anyone who carries out service operations described without carefully observing these instructions will be directly
responsible for any damage caused.
NOTES FOR EQUIPMENT
Equipment shown in this manual is:
• designed expressly for use on these tractors;
• necessary to make a reliable repair;
• accurately built and strictly tested to offer efficient and long-lasting working life.
NOTICES
The words “front”, “rear”, “right hand”, and “left hand” refer to the different parts as seen from the operator’s seat
oriented to the normal direction of movement of the tractor.
SAFETY RULES
PAY ATTENTION TO THIS SYMBOL
This warning symbol points out important messages involving personal
safety. Carefully read the safety rules contained herein and follow advised
precautions to avoid potential hazards and safeguard your safety.
In this manual you will find this symbol together with the following
key-words:
WARNING -it gives warning about improper repair operations and potential
consequences affecting the service technician’s personal safety.
DANGER - it gives specific warning about potential dangers for personal
safety of the operator or other persons directly or indirectly involved in
the operation.
TO PREVENT ACCIDENTS
Most accidents and personal injuries taking place in workshops are due from non-observance of some essential rules
and safety precautions.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this basic precaution would be enough to avoid many severe accidents.
SAFETY RULES
Generalities
• Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open
jackets or shirts with open zips which could get caught on moving parts. Use approved safety clothing such as
anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Wear safety glasses with side guards when cleaning parts using compressed air.
• Damaged or frayed wires and chains are unreliable. Do not use them for lifting or towing.
47913129 19/12/2016
4
9. INTRODUCTION
• Wear suitable protection such as approved eye protection, helmets, special clothing, gloves and footwear whenever
welding. All persons standing in the vicinity of the welding process should wear approved eye protection. NEVER
LOOK AT THE WELDING ARC IF YOUR EYES ARE NOT SUITABLY PROTECTED.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except if they are qualified
operators assisting in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat or at the side
of the machine when operating the fender switches.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated. Stop
the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves, etc.
• All repair and maintenance operations should be carried out with the greatest care and attention.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and all
equipment which should be raised.
• Never check or fill fuel tanks or batteries, nor use starting liquid if you are smoking or near open flames as such
fluids are flammable.
• The fuel filling gun should always remain in contact with the filler neck. Maintain this contact until the fuel stops
flowing into the tank to avoid possible sparks due to static electricity build-up.
• To transfer a failed tractor, use a trailer or a low loading platform trolley if available.
• To load and unload the machine from the transportation means, select a flat area providing a firm support to the
trailer or truck wheels. Firmly tie the machine to the truck or trailer platform and block wheels as required by the
transporter.
• Always use lifting equipment of appropriate capacity to lift or move heavy components.
• Chains should always be safely fastened. Ensure that fastening device is strong enough to hold the load foreseen.
No persons should stand near the fastening point.
• The working area should be always kept CLEAN and DRY. Immediately clean any spillage of water or oil.
• Never use gasoline, diesel oil or other flammable liquids as cleaning agents. Use non-flammable non-toxic propri-
etary solvents.
• Do not pile up grease or oil soaked rags, as they constitute a great fire hazard. Always place them into a metal
container.
START UP
• Never run the engine in confined spaces which are not equipped with adequate ventilation for exhaust gas extrac-
tion.
• Never bring your head, body, arms, legs, feet, hands, fingers near fans or rotating belts.
ENGINE
• Always loosen the radiator cap very slowly before removing it to allow pressure in the system to dissipate. Coolant
should be topped up only when the engine is stopped.
• Do not fill up fuel tank when the engine is running.
• Never adjust the fuel injection pump when the tractor is moving.
• Never lubricate the tractor when the engine is running.
ELECTRICAL SYSTEMS
• If it is necessary to use auxiliary batteries, cables must be connected at both sides as follows: (+) to (+) and (-) to
(-). Avoid short-circuiting the terminals. GAS RELEASED FROM BATTERIES IS HIGHLY FLAMMABLE. During
charging, leave the battery compartment uncovered to improve ventilation. Avoid sparks or flames near the battery
area. Do no smoke.
• Do not charge batteries in confined spaces.
• Always disconnect the batteries before performing any type of service on the electrical system.
47913129 19/12/2016
5
14. Engine - Engine and crankcase
Engine - Remove
DANGER
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply will result in death or serious injury.
D0076A
CAUTION
Pinch hazard!
Always use suitable tools to align mating parts. DO NOT use your hand or fingers.
Failure to comply could result in minor or moderate injury.
C0044A
To access the clutch it is necessary to separate the en-
gine complete with the front axle from the transmission.
Proceed as follows:
1. Disconnect the negative battery lead (1) .
AKU 1
2. Drain off the oil from the gearbox/transmission casing.
3. Drain off the coolant from the engine cooling system.
4. Remove the exhaust pipe. Attach lifting chains (2) to
the bonnet (1) and attach the chain to the hoist.
KAPUTKALDIRMA 2
47913129 19/12/2016
10.1 [10.001] / 3
15. Engine - Engine and crankcase
5. Disconnect the electrical connection (1) of bonnet.
CLUTCH3 3
6. Detach the gas strut (1) from the bonnet.
CLUTCH4 4
7. Remove the two bonnet hinge bolts (1) and take out the
spacers (2) lift the bonnet clear.
CLUTCH5 5
8. Disconnect the two retaining bolts of the guard (1) both
on the right and left hand side of the engine.
SOLDAN 6
47913129 19/12/2016
10.1 [10.001] / 4
16. Engine - Engine and crankcase
9. Unscrew the nut (1) from the weight retaining pin. Re-
move the weights from the front support.
AGIRLIKLAR 7
10. Unscrew the front central and rear reatining bolts on
the front axle shaft guard, then remove the guard (1) .
CLUTCH9 8
11. Remove the circlip (2) and move the front sleeve (1) in
the direction indicated by the arrow until it is released
from the groove on the front axle
CLUTCH10 9
12. Remove the circlip (2) and move the rear sleeve (1) in
the direction indicated by the arrow until it is released
from the groove on the drive.
CLUTCH11 10
47913129 19/12/2016
10.1 [10.001] / 5
17. Engine - Engine and crankcase
13. Remove the propeller shaft central support (1) retain-
ing bolts (2) and extract the shaft together with the
support.
CLUTCH12 11
14. Disconnect the pressure pipe connection (1) of the
hydrostatic steering pump.
CLUTCH13 12
15. Disconnect the pressure pipe connection (1) of he lift
pump.
CULTCH13 13
47913129 19/12/2016
10.1 [10.001] / 6
18. Engine - Engine and crankcase
16. Disconnect the delivery lines of both hydraulic lift
pump (1) and hydrostatic steering pump (2) .
CLUTCH15 14
17. Detach the diesel recovery pipe (3) and delivery pipe
(2) to the diesel pump (1) .
CLUTCH16 15
18. Remove two metal clamps (1) and the rigid pipe (2)
of drawing oil from the transmission housing via lift
pump.
CLUTCH17 16
19. Remove the electrical floor mat.
CLUTCH18 17
47913129 19/12/2016
10.1 [10.001] / 7
19. Engine - Engine and crankcase
20. Remove the electrical connection from the brake fluid
reservoir and take the brake fluid reservoir (1) from the
bracket.
CLUTCH19 18
21. Disconnect the steering oil delivery and return hoses
(1) and (2) . Disconnect the steering cylinder lines (3)
and (4) .
DANFOS 19
BRAG12TRALL0129 20
47913129 19/12/2016
10.1 [10.001] / 8
20. Engine - Engine and crankcase
22. Remove two bolts (1) securing the rear hood to the
gearbox.
CLUTCH21 21
23. Remove two bolts (1) securing the rear hood tothe
bonnet support.
CLUTCH22 22
24. Disconnect the delivery (1) and return lines (2) to the
power steering cylinders.
CLUTCH23 23
25. Disconnect rear brakes oil distributionconnection
pipes (1) and (2) .
CLUTCH24 24
47913129 19/12/2016
10.1 [10.001] / 9
21. Engine - Engine and crankcase
26. Remove the fusebox (1) from the bonnet support.
CLUTCH25 25
27. Remove the electrical oil pressure switch (1) .
CLUTCH26 26
28. Remove the electrical connections of coolant temper-
ature sender (1) .
CLUTCH27 27
29. Remove the electrical connection hydrostaticsteering
pump oil pressure switch (1) .
CLUTCH28 28
47913129 19/12/2016
10.1 [10.001] / 10
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Engine - Engine and crankcase
30. Remove the electrical connection of pump cut–out so-
lenoid sender (1) .
CLUTCH29 29
31. Remove the retaining bolts (1) and (2) for the support.
Remove the retaining nut (3) and detachthe throttle
control tie–rod connected to theinjection pump.
CLUTCH30 30
32. Remove the hand and foot throttle cablescomplete
with their support (4) .
33. Disconnect the electrical connection (1) between the
cab and the engine.
CLUTCH31 31
47913129 19/12/2016
10.1 [10.001] / 11
24. Engine - Engine and crankcase
34. Disconnect the electrical connections from starter mo-
tor (1) .
CLUTCH32 32
35. Disconnect the electrical connections from alternator
(1) .
CLUTCH33 33
36. Disconnect the electrical connection of water in fuel
sensor (1) .
CLUTCH34 34
37. Remove the electrical connection of air filter clogging
sensor (1) .
CLUTCH35 35
47913129 19/12/2016
10.1 [10.001] / 12
25. Engine - Engine and crankcase
38. Remove the two connectors (1) and (2) for the heater
relay.
CLUTCH36 36
39. Remove the two connectors of the brake lights switch
(1) .
CLUTCH37 37
40. Loosen the corresponding retaining clamps and ex-
tract the pipes (1) , (2) , (3) and (4) .
CLUTCH38 38
47913129 19/12/2016
10.1 [10.001] / 13
26. Engine - Engine and crankcase
41. Hitch the engine to the hoist with the chains (1) an-
chouring it to the attachments on the engine.
MOTORKALDIRMA 39
42. Engine lifting points are (1) , (2) and (3) .
CLUTCH40 40
43. Position the movable tool for dismantling tractors
380000569 with the bracket 380000500 and adapter
plate 380000844 under the engine and place a
wooden block in between the points of contact be-
tween the tool and tractor as shown in the fig.
CLUTCH41 41
47913129 19/12/2016
10.1 [10.001] / 14
27. Engine - Engine and crankcase
44. Unscrew the two bolts (1) both left and right side and
securing the engine to the transmission. Access is
through the sides of the tractor.
CLUTCH42 42
45. Remove the remaining six retaining bolts (1) at the
bottom and side.
CLUTCH43 43
46. Seperate the engine from the transmission with the
tool 380000569 (1) .
ALTTEZGAH 44
47913129 19/12/2016
10.1 [10.001] / 15