HURRICANE CHECKLIST.pdf
•
0 likes•604 views
The document discusses the results of a study analyzing the effects of a training program on employee performance. The study found that employees who participated in the training program showed significant improvements in key job skills compared to a control group. They demonstrated stronger communication abilities, increased attention to detail, and higher levels of efficiency. The training program was deemed an effective way to boost worker productivity and quality of work.
Report
Share
Report
Share
Recommended
SAFETY TOOLBOX TALK: Seven Common Accident Causes
The document discusses seven common causes of workplace accidents. It notes that 80% of accidents are due to unsafe acts by those involved rather than unsafe conditions. The seven causes are: taking shortcuts, overconfidence, starting tasks without full instructions, poor housekeeping, ignoring safety procedures, mental distractions, and failure to plan work. Addressing these behaviors could help reduce accidents. The document advises workers to learn from it and be careful.
Introduction.137697294749987.OS
Here are some ways employers can motivate employees to comply with health and safety procedures:
- Provide regular training and reminders on procedures to increase awareness and understanding of why they are important.
- Lead by example by modeling safe behaviors themselves and prioritizing safety in decision making.
- Recognize and reward safe behaviors through incentives like bonuses, time off, or public praise to positively reinforce compliance.
- Involve employees in safety committees and discussions to give them ownership over procedures and make compliance feel more voluntary than mandatory.
- Clearly communicate how compliance protects not only their own safety but that of coworkers to appeal to team and community values.
- Cite real accident examples to demonstrate the very real risks
Top 16 Construction Hazards
What are the main hazards in construction?
What are the main hazards in construction?
« Back to Table of Contents
Among the dangers in construction are:
•Falls from working at height,
•Crush injuries in excavation work,
•Slips and trips,
•Being struck by falling objects,
•Moving heavy loads,
•Bad working positions, often in confined spaces,
•Being struck or crushed by a workplace vehicle,
•Receiving injuries from hand tools,
•Inhalation of dust,
•Handling of rough materials,
•Exposure to dangerous substances (chemical and biological),
•Working near, in, or over water,
•Exposure to radiation,
•Loud noise,
•Vibration from tools or vibrating machinery.
WSM Yard-High-Pressure Safety-22.12.19
This document summarizes the key points from a weekly safety meeting about high-pressure application safety. It outlines several hazards of high-pressure systems, including sudden releases of stored energy, flying objects or shrapnel, and oxygen displacement. It lists common causes of pressure system failures and requirements for a written safety system of work, including proper testing, fittings, supervision, and segregation. The document concludes with specific requirements for high-pressure equipment, including relief valves, safety lines, secured hoses, barriers during testing, and training for working on high-pressure systems.
LOTO & ENERGY ISOLATION.pptx
The correct action for working on a live panel or process pipeline is to follow all the steps listed:
A. Permit to Work
B. Manage System Risk Assessment
C. Isolate the energy sources
D. Lockout/Tagout the energy isolating devices
E. Drain the pipeline if required
F. Test that the power/energy is isolated using a multimeter for panels
G. Ensure only competent and authorized staff perform the work
H. All of the above steps should be followed to safely isolate, control and verify isolation of hazardous energy sources.
Fixed or semi fixed-d10 d03192
Fixed or semi-fixed foam fire protection systems can reliably protect flammable liquid storage tanks from fire if properly engineered, installed, and maintained. There are two main types of systems - fixed systems with permanently installed proportioning components, and semi-fixed systems which use portable foam-producing materials connected to fixed discharge devices. To select the correct system, it is important to understand the type of storage tank (cone roof, floating roof, etc.), foam discharge devices (foam chambers, monitors), and foam application methods (sub-surface injection, over the top). Proper sizing of a system requires calculating the fuel surface area, application rate, discharge duration, and quantity of foam concentrate needed.
FIre Fighting Elite Fire hydraulic Calculation As per NFPA Standard
This document discusses mechanical, electrical, and plumbing (MEP) systems and fire protection systems. It covers topics such as the need for MEP systems, fire triangles, causes and classifications of fires, National Fire Protection Association (NFPA) codes, firefighting systems like sprinklers and pumps, and sizing of fire water tanks and diesel tanks. The document is intended as training material for fire protection system design and hydraulic calculations using Elite software.
Safety Culture Power Point
This document discusses strategies for improving safety culture in an organization. It defines safety culture as the set of values that determine how management and employees act at work, rather than simply prioritizing safety. Some recommendations include viewing safety as a continuous process rather than just compliance, analyzing accidents by looking at the systemic factors that led to them rather than blame, integrating safety fully into daily operations, and involving employees in safety decision-making. Lastly, it notes that truly changing an organization's safety culture requires consistent leadership promoting new safety values through education and encouragement over time.
Recommended
SAFETY TOOLBOX TALK: Seven Common Accident Causes
The document discusses seven common causes of workplace accidents. It notes that 80% of accidents are due to unsafe acts by those involved rather than unsafe conditions. The seven causes are: taking shortcuts, overconfidence, starting tasks without full instructions, poor housekeeping, ignoring safety procedures, mental distractions, and failure to plan work. Addressing these behaviors could help reduce accidents. The document advises workers to learn from it and be careful.
Introduction.137697294749987.OS
Here are some ways employers can motivate employees to comply with health and safety procedures:
- Provide regular training and reminders on procedures to increase awareness and understanding of why they are important.
- Lead by example by modeling safe behaviors themselves and prioritizing safety in decision making.
- Recognize and reward safe behaviors through incentives like bonuses, time off, or public praise to positively reinforce compliance.
- Involve employees in safety committees and discussions to give them ownership over procedures and make compliance feel more voluntary than mandatory.
- Clearly communicate how compliance protects not only their own safety but that of coworkers to appeal to team and community values.
- Cite real accident examples to demonstrate the very real risks
Top 16 Construction Hazards
What are the main hazards in construction?
What are the main hazards in construction?
« Back to Table of Contents
Among the dangers in construction are:
•Falls from working at height,
•Crush injuries in excavation work,
•Slips and trips,
•Being struck by falling objects,
•Moving heavy loads,
•Bad working positions, often in confined spaces,
•Being struck or crushed by a workplace vehicle,
•Receiving injuries from hand tools,
•Inhalation of dust,
•Handling of rough materials,
•Exposure to dangerous substances (chemical and biological),
•Working near, in, or over water,
•Exposure to radiation,
•Loud noise,
•Vibration from tools or vibrating machinery.
WSM Yard-High-Pressure Safety-22.12.19
This document summarizes the key points from a weekly safety meeting about high-pressure application safety. It outlines several hazards of high-pressure systems, including sudden releases of stored energy, flying objects or shrapnel, and oxygen displacement. It lists common causes of pressure system failures and requirements for a written safety system of work, including proper testing, fittings, supervision, and segregation. The document concludes with specific requirements for high-pressure equipment, including relief valves, safety lines, secured hoses, barriers during testing, and training for working on high-pressure systems.
LOTO & ENERGY ISOLATION.pptx
The correct action for working on a live panel or process pipeline is to follow all the steps listed:
A. Permit to Work
B. Manage System Risk Assessment
C. Isolate the energy sources
D. Lockout/Tagout the energy isolating devices
E. Drain the pipeline if required
F. Test that the power/energy is isolated using a multimeter for panels
G. Ensure only competent and authorized staff perform the work
H. All of the above steps should be followed to safely isolate, control and verify isolation of hazardous energy sources.
Fixed or semi fixed-d10 d03192
Fixed or semi-fixed foam fire protection systems can reliably protect flammable liquid storage tanks from fire if properly engineered, installed, and maintained. There are two main types of systems - fixed systems with permanently installed proportioning components, and semi-fixed systems which use portable foam-producing materials connected to fixed discharge devices. To select the correct system, it is important to understand the type of storage tank (cone roof, floating roof, etc.), foam discharge devices (foam chambers, monitors), and foam application methods (sub-surface injection, over the top). Proper sizing of a system requires calculating the fuel surface area, application rate, discharge duration, and quantity of foam concentrate needed.
FIre Fighting Elite Fire hydraulic Calculation As per NFPA Standard
This document discusses mechanical, electrical, and plumbing (MEP) systems and fire protection systems. It covers topics such as the need for MEP systems, fire triangles, causes and classifications of fires, National Fire Protection Association (NFPA) codes, firefighting systems like sprinklers and pumps, and sizing of fire water tanks and diesel tanks. The document is intended as training material for fire protection system design and hydraulic calculations using Elite software.
Safety Culture Power Point
This document discusses strategies for improving safety culture in an organization. It defines safety culture as the set of values that determine how management and employees act at work, rather than simply prioritizing safety. Some recommendations include viewing safety as a continuous process rather than just compliance, analyzing accidents by looking at the systemic factors that led to them rather than blame, integrating safety fully into daily operations, and involving employees in safety decision-making. Lastly, it notes that truly changing an organization's safety culture requires consistent leadership promoting new safety values through education and encouragement over time.
Hazard identification
This document discusses hazard identification and risk assessment in the workplace. It defines a hazard as anything that could cause harm and explains that hazard identification involves determining if exposure to a stressor can increase health issues. It provides examples of workplace hazards like frayed wires, unstable stacks of boxes, and loud machinery. The document also defines risk assessment as examining work activities for potential harm and outlines steps employers should take to control risks, primarily trying to eliminate hazards, then substitute or isolate them, and using personal protective equipment as a last resort. Workers are advised to report any unfixed hazards that could cause serious harm.
Troubleshooting
Explains what troubleshooting is, what skills are involved, and clears up some common misconceptions. Originally designed with IT Helpdesks in mind, but it could apply to any kind of troubleshooting.
=========================
Wrote this a VERY long time ago! I always meant to revisit/revamp it, but never quite got round to it. But people seem to get value from it, so I'll leave it up :)
High pressure water jetting Will Lee
Water jetting uses high pressure water pumps to clean or prepare surfaces. It presents risks like death or injury if not performed safely. Proper training, equipment maintenance, and personal protective equipment can reduce risks. Industry standards provide guidance on jetting classes, operator training, and maintaining safe work procedures and equipment. Following these standards helps persons conducting businesses maintain safe workplaces when jetting.
Safety at workplace
Safety at the workplace requires awareness of both unsafe acts and unsafe conditions. Common safety issues include slips, trips, and falls which can be prevented through proper lifting techniques and clear walkways. It is important to notify supervisors of any potential hazards, follow safety procedures, and report any issues or accidents. Basic safety signs use distinctive shapes, colors and symbols to clearly communicate important safety information.
Line Of Fire.pptx
Construction workers face a wide variety of hazards that can result in injury or death if proper precautions are not taken. Simple precautions can help avoid injuries from being in the "line of fire" of hazards such as heavy machinery, falling objects, welding sparks, and more. It is everyone's responsibility on a construction site to be aware of potential lines of fire, remain vigilant of changing work environments, and use appropriate protective equipment and safety measures.
Ppe Training
A powerpoint presentation designed to cover the basics of Personal Protective Equipment including gloves, respiratory, earplugs, etc... Can be used in training employees. Made available free from www.nationalsafetyinc.com
WorkSafeBC (13).pdf
The document provides information about WorkSafeBC and resources for joint health and safety committees. It discusses WorkSafeBC's role in promoting workplace safety and providing support for injured workers. It also provides contact information for WorkSafeBC's prevention information line and resources available on worksafebc.com and from the WorkSafeBC store.
Safety hand tools & grinding
This document provides information on safety practices for hand tools and grinding tools. It discusses hazards associated with both types of tools and outlines safety precautions and regulations. For hand tools, common hazards include tool misuse, improper maintenance, and loose or damaged parts. Grinding tools can cause injuries from contact with abrasive surfaces or failure of grinding wheels. The document recommends personal protective equipment, proper tool use and maintenance, guarding, training, and following manufacturer guidelines to prevent injuries when using hand and grinding tools.
December -15 Daily Observation Report
The document is a site safety observation report prepared by Mohammed Mubasheeruddin on December 15, 2016. It details three safety observations made at a construction site, including workers following without proper protective equipment, improperly stocked ducting material, and improperly stoked fire fighting pipes. For each observation, the report notes an identified unsafe act and the corresponding correction that was taken.
Safestart Overview
1. SafeStart is a safety program used by over 1.5 million people in 38 countries that has led to injury reductions of 60-90% through teaching a common safety language and techniques.
2. The program teaches that unintentional injuries are often caused by rushing, frustration, fatigue, or complacency, and provides techniques to recognize when one is in these states to prevent mistakes.
3. SafeStart also has materials to teach family members at home in order to encourage safe behaviors 24/7.
Occupational Health and Safety Hazard Inspections Process with Reporting
The document discusses workplace hazard inspections and incident investigations. It provides steps for conducting hazard inspections, which include selecting an inspection team, using a checklist to inspect the workplace and identify hazards, recording hazards and actions, and implementing and monitoring an OHS action plan. It emphasizes the importance of hazard reporting, investigating incidents to identify underlying causes, and developing control plans with timelines and responsibilities. The objective is to identify hazards and risks to prevent injuries and ensure employees return home safely.
Suspended cradle presentation
This document provides information on the components, operation, inspection, maintenance and safety regulations for a suspended electric hoist system. It describes the main parts of the cradle including the hand rails, hoist, electromagnetic brake motor, and anti-tilting lock system. It provides details on inspecting, operating and maintaining the electric, wire rope, and control systems. The document emphasizes safety practices such as qualifications for operators, use of personal protective equipment, load limits, emergency procedures and prohibiting unsafe acts.
Near Miss Reporting
This document outlines the goals and process for near miss reporting. The goals are to share experiences to prevent injuries, collect safety data, and foster a safety culture. A near miss is an unreported event that could have caused harm. Reporting identifies safety issues and solutions. The stages of management include identification, analysis of direct and root causes, solution identification, and dissemination of lessons learned. Near miss reporting provides valuable safety data without needing an actual injury.
Promoting a positive attitude towards workplace safety
The document discusses the importance of promoting a positive attitude towards workplace safety. It outlines that safety is important from a social responsibility, legal, and economic perspective. The document then details specific duties and obligations outlined in the Occupational Health and Safety Act, including maintaining equipment safely, ensuring protective devices are used properly, and advising workers of hazards. It provides examples of common workplace hazards like slips/trips, chemicals, electricity, and health issues. Finally, it emphasizes the importance of attitude in preventing injuries, and promotes techniques like training, supervision, engineering controls, and PPE use.
Safety Risk Assessment {Slide} PP. 09-19-12 -
This document provides information on performing safety risk assessments. It defines risk assessment as identifying hazards, analyzing risks, and determining controls. It explains that risk assessments help ensure controls are adequate, prevent injuries, and prioritize hazards. The document outlines how to perform an assessment by including various personnel, identifying hazards and evaluating likelihood and severity of potential injuries, considering normal and abnormal situations, and reviewing all relevant safety information. Triggers for conducting an assessment include new projects, processes, equipment, employees, facilities, chemicals. It describes principles of identifying, evaluating, eliminating, substituting, isolating risks, and using PPE or avoiding risks. The final section presents the mission of the Safety Risk Assessment team to identify and eliminate hazards through assessments of
Full report (Petronas Prai)
This document provides a job method statement for testing oxygen concentration in an LPG tank using a Model 3110 Portable Trace Oxygen Analyzer. It outlines the objectives, equipment, manpower, and 14 step process for connecting the analyzer to the LPG tank, regulating pressure and flow, purging the system, taking an oxygen reading, recording results, and disconnecting from the tank. Figures and labels are also provided to identify components of the analyzer.
Safety Role of management
This report discusses the role of management in safety. It outlines five key steps to successful safety management: setting a policy, organizing staff, planning and setting standards, measuring performance, and learning from experience through audits and reviews. Risk assessment methods are described including identifying hazards, deciding who may be harmed, evaluating risks, recording findings, and reviewing assessments. Total quality management elements are also discussed including management commitment, goal setting, engineering controls, training, accident investigation, and employee safety committees. The relationship between total quality management and safety management is emphasized.
training near miss program
The document outlines Millennium Products' new Near Miss Program. It defines a near miss as an unplanned event that could have caused injury or damage but did not. The objectives of the program are to identify risks, prevent accidents, and improve safety culture. Employees are encouraged to report near misses so their causes can be analyzed and corrective actions implemented to prevent future incidents. Examples of near misses at Millennium Products are provided to demonstrate how the program will work.
Man and machine interface
Man and Machine Interface
Working around heavy equipment can be extremely dangerous. Too many workers are killed each year when they are run over or struck by these pieces of machinery. It’s important to know the safety precautions to take when working in the vicinity of heavy equipment such as dump trucks, front-end loaders, cranes, Excavator, Bob Cat, Forklift, Concrete Mixture Truck, other heavy trucks/Equipment's, etc.
Construction safety lecture-2
The document discusses construction safety and health topics including potential hazards, OSHA standards, and environmental health issues. It outlines hazards such as falls, trench collapses, and electric shock. It describes OSHA standards for scaffolding, fall protection, ladders, stairways, trenching, cranes, and head protection. It also addresses environmental health issues in construction including noise, dust, radiation, toxic materials, heat, and cold. Throughout, it provides solutions and guidelines to mitigate hazards and ensure worker safety and health.
More Related Content
What's hot
Hazard identification
This document discusses hazard identification and risk assessment in the workplace. It defines a hazard as anything that could cause harm and explains that hazard identification involves determining if exposure to a stressor can increase health issues. It provides examples of workplace hazards like frayed wires, unstable stacks of boxes, and loud machinery. The document also defines risk assessment as examining work activities for potential harm and outlines steps employers should take to control risks, primarily trying to eliminate hazards, then substitute or isolate them, and using personal protective equipment as a last resort. Workers are advised to report any unfixed hazards that could cause serious harm.
Troubleshooting
Explains what troubleshooting is, what skills are involved, and clears up some common misconceptions. Originally designed with IT Helpdesks in mind, but it could apply to any kind of troubleshooting.
=========================
Wrote this a VERY long time ago! I always meant to revisit/revamp it, but never quite got round to it. But people seem to get value from it, so I'll leave it up :)
High pressure water jetting Will Lee
Water jetting uses high pressure water pumps to clean or prepare surfaces. It presents risks like death or injury if not performed safely. Proper training, equipment maintenance, and personal protective equipment can reduce risks. Industry standards provide guidance on jetting classes, operator training, and maintaining safe work procedures and equipment. Following these standards helps persons conducting businesses maintain safe workplaces when jetting.
Safety at workplace
Safety at the workplace requires awareness of both unsafe acts and unsafe conditions. Common safety issues include slips, trips, and falls which can be prevented through proper lifting techniques and clear walkways. It is important to notify supervisors of any potential hazards, follow safety procedures, and report any issues or accidents. Basic safety signs use distinctive shapes, colors and symbols to clearly communicate important safety information.
Line Of Fire.pptx
Construction workers face a wide variety of hazards that can result in injury or death if proper precautions are not taken. Simple precautions can help avoid injuries from being in the "line of fire" of hazards such as heavy machinery, falling objects, welding sparks, and more. It is everyone's responsibility on a construction site to be aware of potential lines of fire, remain vigilant of changing work environments, and use appropriate protective equipment and safety measures.
Ppe Training
A powerpoint presentation designed to cover the basics of Personal Protective Equipment including gloves, respiratory, earplugs, etc... Can be used in training employees. Made available free from www.nationalsafetyinc.com
WorkSafeBC (13).pdf
The document provides information about WorkSafeBC and resources for joint health and safety committees. It discusses WorkSafeBC's role in promoting workplace safety and providing support for injured workers. It also provides contact information for WorkSafeBC's prevention information line and resources available on worksafebc.com and from the WorkSafeBC store.
Safety hand tools & grinding
This document provides information on safety practices for hand tools and grinding tools. It discusses hazards associated with both types of tools and outlines safety precautions and regulations. For hand tools, common hazards include tool misuse, improper maintenance, and loose or damaged parts. Grinding tools can cause injuries from contact with abrasive surfaces or failure of grinding wheels. The document recommends personal protective equipment, proper tool use and maintenance, guarding, training, and following manufacturer guidelines to prevent injuries when using hand and grinding tools.
December -15 Daily Observation Report
The document is a site safety observation report prepared by Mohammed Mubasheeruddin on December 15, 2016. It details three safety observations made at a construction site, including workers following without proper protective equipment, improperly stocked ducting material, and improperly stoked fire fighting pipes. For each observation, the report notes an identified unsafe act and the corresponding correction that was taken.
Safestart Overview
1. SafeStart is a safety program used by over 1.5 million people in 38 countries that has led to injury reductions of 60-90% through teaching a common safety language and techniques.
2. The program teaches that unintentional injuries are often caused by rushing, frustration, fatigue, or complacency, and provides techniques to recognize when one is in these states to prevent mistakes.
3. SafeStart also has materials to teach family members at home in order to encourage safe behaviors 24/7.
Occupational Health and Safety Hazard Inspections Process with Reporting
The document discusses workplace hazard inspections and incident investigations. It provides steps for conducting hazard inspections, which include selecting an inspection team, using a checklist to inspect the workplace and identify hazards, recording hazards and actions, and implementing and monitoring an OHS action plan. It emphasizes the importance of hazard reporting, investigating incidents to identify underlying causes, and developing control plans with timelines and responsibilities. The objective is to identify hazards and risks to prevent injuries and ensure employees return home safely.
Suspended cradle presentation
This document provides information on the components, operation, inspection, maintenance and safety regulations for a suspended electric hoist system. It describes the main parts of the cradle including the hand rails, hoist, electromagnetic brake motor, and anti-tilting lock system. It provides details on inspecting, operating and maintaining the electric, wire rope, and control systems. The document emphasizes safety practices such as qualifications for operators, use of personal protective equipment, load limits, emergency procedures and prohibiting unsafe acts.
Near Miss Reporting
This document outlines the goals and process for near miss reporting. The goals are to share experiences to prevent injuries, collect safety data, and foster a safety culture. A near miss is an unreported event that could have caused harm. Reporting identifies safety issues and solutions. The stages of management include identification, analysis of direct and root causes, solution identification, and dissemination of lessons learned. Near miss reporting provides valuable safety data without needing an actual injury.
Promoting a positive attitude towards workplace safety
The document discusses the importance of promoting a positive attitude towards workplace safety. It outlines that safety is important from a social responsibility, legal, and economic perspective. The document then details specific duties and obligations outlined in the Occupational Health and Safety Act, including maintaining equipment safely, ensuring protective devices are used properly, and advising workers of hazards. It provides examples of common workplace hazards like slips/trips, chemicals, electricity, and health issues. Finally, it emphasizes the importance of attitude in preventing injuries, and promotes techniques like training, supervision, engineering controls, and PPE use.
Safety Risk Assessment {Slide} PP. 09-19-12 -
This document provides information on performing safety risk assessments. It defines risk assessment as identifying hazards, analyzing risks, and determining controls. It explains that risk assessments help ensure controls are adequate, prevent injuries, and prioritize hazards. The document outlines how to perform an assessment by including various personnel, identifying hazards and evaluating likelihood and severity of potential injuries, considering normal and abnormal situations, and reviewing all relevant safety information. Triggers for conducting an assessment include new projects, processes, equipment, employees, facilities, chemicals. It describes principles of identifying, evaluating, eliminating, substituting, isolating risks, and using PPE or avoiding risks. The final section presents the mission of the Safety Risk Assessment team to identify and eliminate hazards through assessments of
Full report (Petronas Prai)
This document provides a job method statement for testing oxygen concentration in an LPG tank using a Model 3110 Portable Trace Oxygen Analyzer. It outlines the objectives, equipment, manpower, and 14 step process for connecting the analyzer to the LPG tank, regulating pressure and flow, purging the system, taking an oxygen reading, recording results, and disconnecting from the tank. Figures and labels are also provided to identify components of the analyzer.
Safety Role of management
This report discusses the role of management in safety. It outlines five key steps to successful safety management: setting a policy, organizing staff, planning and setting standards, measuring performance, and learning from experience through audits and reviews. Risk assessment methods are described including identifying hazards, deciding who may be harmed, evaluating risks, recording findings, and reviewing assessments. Total quality management elements are also discussed including management commitment, goal setting, engineering controls, training, accident investigation, and employee safety committees. The relationship between total quality management and safety management is emphasized.
training near miss program
The document outlines Millennium Products' new Near Miss Program. It defines a near miss as an unplanned event that could have caused injury or damage but did not. The objectives of the program are to identify risks, prevent accidents, and improve safety culture. Employees are encouraged to report near misses so their causes can be analyzed and corrective actions implemented to prevent future incidents. Examples of near misses at Millennium Products are provided to demonstrate how the program will work.
Man and machine interface
Man and Machine Interface
Working around heavy equipment can be extremely dangerous. Too many workers are killed each year when they are run over or struck by these pieces of machinery. It’s important to know the safety precautions to take when working in the vicinity of heavy equipment such as dump trucks, front-end loaders, cranes, Excavator, Bob Cat, Forklift, Concrete Mixture Truck, other heavy trucks/Equipment's, etc.
Construction safety lecture-2
The document discusses construction safety and health topics including potential hazards, OSHA standards, and environmental health issues. It outlines hazards such as falls, trench collapses, and electric shock. It describes OSHA standards for scaffolding, fall protection, ladders, stairways, trenching, cranes, and head protection. It also addresses environmental health issues in construction including noise, dust, radiation, toxic materials, heat, and cold. Throughout, it provides solutions and guidelines to mitigate hazards and ensure worker safety and health.
What's hot (20)
Occupational Health and Safety Hazard Inspections Process with Reporting
Occupational Health and Safety Hazard Inspections Process with Reporting
Promoting a positive attitude towards workplace safety
Promoting a positive attitude towards workplace safety