The document provides installation instructions for replacing rechargeable battery kits in LYNXR-EN/LYNXR-ENSIA and LYNXR-I/LYNXR-ISIA series control panels. The 10 step process involves removing the old battery, installing the new battery kit which includes the battery pack and retainer, reconnecting the battery connector, and allowing 48 hours for the new battery to fully charge. Diagrams show the battery replacement for the LYNXR-EN and LYNXR-I control panels.
Power point presentation on logical families.
A good presentation cover all topics.
For any other type of ppt's or pdf's to be created on demand contact -dhawalm8@gmail.com
mob. no-7023419969
Power point presentation on logical families.
A good presentation cover all topics.
For any other type of ppt's or pdf's to be created on demand contact -dhawalm8@gmail.com
mob. no-7023419969
A unijunction transistor (UJT) is a three-lead electronic semiconductor device with only one junction that acts exclusively as an electrically controlled switch.
The UJT is not used as a linear amplifier. It is used in free-running oscillators, synchronized or triggered oscillators, and pulse generation circuits at low to moderate frequencies (hundreds of kilohertz). It is widely used in the triggering circuits for silicon controlled rectifiers. The low cost per unit, combined with its unique characteristic, have warranted its use in a wide variety of applications like oscillators, pulse generators, saw-tooth generators, triggering circuits, phase control, timing circuits, and voltage- or current-regulated supplies.[1] The original unijunction transistor types are now considered obsolete, but a later multi-layer device, the programmable unijunction transistor (PUT), is still widely available.
A unijunction transistor (UJT) is a three-lead electronic semiconductor device with only one junction that acts exclusively as an electrically controlled switch.
The UJT is not used as a linear amplifier. It is used in free-running oscillators, synchronized or triggered oscillators, and pulse generation circuits at low to moderate frequencies (hundreds of kilohertz). It is widely used in the triggering circuits for silicon controlled rectifiers. The low cost per unit, combined with its unique characteristic, have warranted its use in a wide variety of applications like oscillators, pulse generators, saw-tooth generators, triggering circuits, phase control, timing circuits, and voltage- or current-regulated supplies.[1] The original unijunction transistor types are now considered obsolete, but a later multi-layer device, the programmable unijunction transistor (PUT), is still widely available.
1. LYNXRCHKIT-SC, LYNXRCHKIT-HC
AND LYNXRCHKIT-SHA
RECHARGEABLE BATTERY KITS
INSTALLATION INSTRUCTIONS
GENERAL INFORMATION
The LYNXRCHKIT-SC, LYNXRCHKIT-HC and LYNXRCHKIT-SHA rechargeable battery kits are
designed to replace the rechargeable battery installed in the LYNXR-EN/LYNXR-ENSIA, LYNXR-
I/LYNXR-ISIA series control panels. When battery replacement is required, perform the following
steps.
STEP ACTION
1. Unplug the transformer from the wall outlet and open the control panel cover.
2. Remove the battery retainer and disconnect the battery pack connector from the receptacle on
the terminal block PC board. Refer to Figure 1 for the LYNXR-EN or Figure 2 for the LYNXR-I.
3. Remove the battery pack from the back plate.
4. Replace tape on back plate assembly (if necessary).
5. Install the battery pack in the back plate. Refer to Figure 1 for the LYNXR-EN or Figure 2 for the
LYNXR-I.
6. Install the battery retainer.
7. Connect the battery connector to the receptacle on the terminal block PC board.
8. After the wiring connection has been made, snap the front assembly to the back plate.
9. Plug the transformer into a 24-hour, 110VAC unswitched outlet.
10. Rechargeable batteries may take up to 48-hours to fully charge. The “LOW BAT” message
should clear within four hours or by entering Test Mode.
Ensure the control panel cover is closed prior to applying AC power.
LYNXRCHKIT-HC OR LYNXRCHKIT-SC
RETAINER
BATTERY
PACK
TAPE
BATTERY
CONNECTOR
K51 X
08
X
MXX
BATTERY
RECEPTACLE
01009-006-V0
Figure 1 – Replacing the LYNXR-EN Battery pack