Hmdp hl-ptcl-04760-mx-portable tool box-v30

Form Owner: Product Engineering - Issue Date: 11/17/08- Version #: 6
Proprietary & Confidential
The Home DepotCompany Information
1 of 47
The Home Depot
Testing Protocol (PPT Requirement- Attachment A)
2455 PACES FERRY ROAD
ATLANTA, GEORGIA, USA 30339-4024
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
INITIAL PROTOCOL DATE REVISION # 30
REPORT # PREVIOUS REPORT #
PRODUCT DESCRIPTION PORTABLE PLASTIC TOOL BOX
SP NAME
# Test Property Test Method
Sample
Size
Test Principle/Requirements Results Rating
Defect
Code
NOTE: All the below tests are to be conducted for PPT. Only the shaded tests are to be conducted for PoPT.
All the Information and claims on the PLM should be verified and recordedin protocol.
SCOPE:
This protocol is applicable for testing portable plastic tool boxes.
LABELING & MARKING VERIFICATION (FOR PACKAGE & PRODUCT)
Note: For PPT (Pre-Purchase Test), report as UNSAT if no retail package or artwork was provided.
1.1 Labeling- Packaging
(Packaging copy or artwork
request form may be
substituted)
Mexican Official
Standard NOM -
050 - SCFI -
2004,
"Commercial
information -
General
regulations
required for
products"
1 The following information is required on product
labels:
The trademark, name and/or company name and
address of manufacturer or importer.
The name or generic denomination of the
product.
A quantity designation according to
NOM-030-SCFI, "Declaration of quantity in label
specifications."
A message indicating the country of origin.
Risk warnings, if appropriate.
Instructions for use and warnings, where
applicable, are to be included in a manual. The
label shall read: "SEE MANUAL", or
"OPERATION MANUAL."
An expiration date or preferred consumption
date.
1.2 Language and Terms Mexican Official
Standard NOM -
050 - SCFI -
2004,
"Commercial
information -
General
1 Information contained in labels shall:
Be in Spanish without precluding presentation in
other languages. Information presented in other
languages should also be in Spanish in at least
the same font size.
Be expressed in legible and understandable
terms that are clear to consumers.

2 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
regulations
required for
products"
Comply with NOM -008-SCFI, General system of
measurement units" and NOM - 030-SCFI,
"Declaration of quantity in label specifications",
without precluding other systems. Information
expressed in a different system should also have
the same font size.
Be included on a label that remains with the item
until the moment of use by the consumer.
Be placed on the principal display panel.
1.3 Operation and Direction Mexican Official 1 Manuals should be written in Spanish according
Manuals Standard NOM - to the General System of Measurement Units
050 - SCFI - without precluding the addition of other unit
2004, systems. Information expressed in other units
"Commercial should also appear in Spanish with the same font
information - size. They shall be issued without additional
General charge to the consumer. Manuals should clearly
regulations and precisely indicate conditions for normal use,
required for handling, and assembly and include appropriate
products" warnings relative to the safe and reliable
handling of the product. They shall include:
The name or trademark of the producer or
importer;
Identification of the product
Procedures to install, connect, assemble or
maintain the product for adequate functioning.
1.4 Statement of Quantity Mexican Official 1 Net contents and dry weight must be located on
the main display surface and should be free of
any extraneous information. If applicable, the
declared dry weight must be located adjacent to
the declaration of the net contents. Consult the
specification for guidance regarding specific
verbiage, products, package configurations or
calculation of display surface area.
Standard
NOM-030-SCFI-2
006, "Statement
of Quantity on
Labels"
1.5 Use labeling CPSD-GB-01057
-MTHD
1 Use/care instructions that are clear and
understandable shall be provided in language

3 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
appropriate to destination countries.
1.6 *Claim verification CPSD-GB-01057
-MTHD and
CPSD-GB-01058
-MTHD, as
Applicable
1 Verify performance claims made on packaging
evaluated for accuracy. Report each claim made
and if it conforms or in non-conformance and
how. If a claim cannot be confirmed for some
reason then the client should be consulted on
how to report.
Each claim should be listed and verified as
appropriate:
Claim:
1.
2.
Note: All claims must be listed individually and
verified. If testing TAT is greater than 10 days
Contact client for approval prior to testing. If not
verified, marked "NV" next to the claim.
1.7 Mexico Packaging and
Instructions
Home Depot
PPT-01
1 Mexico Market Packaging and Instructions
Requirements:
If warranty information, instructions and
caution/warning statements are present they
must be bilingual Spanish/English, if the product
is intended for the Mexican market. (HD-ME
1.4.1.7)
1.8 * NOM labeling certificate
review
Home Depot
Requirem ent
1 Vendor shall provide a Constancia certificate
demonstrating compliance to all NOM labeling
requirements that apply to the product (ie: NOM
050, NOM 004).
Note: Photo of the certification shall be included
in the test report.
1.9 Barcode requirement CPSD-GB-01057
-MTHD
1 All products are required to have a unique,
scannable barcode according to the Uniform
Code Council’s specifications for product

4 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
identification at the sales register sale. In
addition, all barcodes must have the
corresponding human readable numbers under
the barcode
Remark: Barcode scan shall be checked during
PSI.
1.1
0
* ANSI verification CPSD-GB-01057
-MTHD and
1 Verify ANSI claim made on packaging evaluated
for accuracy. Report claim made and if it
CPSD-GB-01058 conforms or in non-conformance and how. If a
-MTHD, as claim cannot be confirmed for some reason then
Applicable the client should be consulted on how to report.
The Lab is responsible to collect the information
whether product comply with ANSI standard. If
yes, ANSI claim must be verified through PPT.
Must be recorded as Pass, Fail or Not
Claimed.
Do not put in NP (No Packaging) or NA (Not
Applicable) for this field. If packaging is not
provided, the lab will contact the factory/supplier
and find out if it is claimed on the packaging.
Each claim should be listed and verified as
appropriate:
Claim:
1.
2.
Note: All claims must be listed individually and
verified. If testing TAT is greater than 10 days
Contact client for approval prior to testing. If not
verified, marked "NV" next to the claim.
1.1
1
Accuracy of order or
number for bilingual
instructions / packaging
CPSD-GB-01057
-MTHD
1 [Applicable to all bilingual assembly instruction,
instruction manual, package, artwork]
1. The number of components mentioned in
English version must be equivalent to French/
Spanish version (e.g. in assembly instruction,

5 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
part list)
2. The number of bullet points in English
version must be equivalent to French/ Spanish
version.
PHYSICAL REQUIREMENTS (CONSTRUCTION, WORKMANSHIP, ETC…)
2.1 Master Carton Packaging
Compliance
Client
requirement
1 All Direct Import Programs for The Home Depot
USA and Canada will be subject to the Master
Carton Packaging Compliance, effective from
th
July 27 , 2009.
In the case of multipack master carton’s (1 SKU
with more than one master carton) the master
pack is exempt from the compliance program.
1. If no carton size in recorded in Home Depot’s
PLM System, then this is rated as failed.
2. If the carton size is recorded in PLM there are
two possible options:
The supplier/ factory may provide the actual
carton. If the actual carton is provided and the
measured dimensions are not within 5% of the
recorded PLM data, then this is rated as a
failure.
Or
If carton size is recorded in PLM, and the
supplier/ factory does not provide the actual
carton, then record the data provided in PLM
as data only and do not fail.
PLM:
Actual:

6 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
2.2 Dimensions CPSD-GB-01056
-MTHD
1 For items without Product Requirement:
Report overall dimensions; shall meet label
claims (if applicable) (±5%)
shall be measured / reported as per claimed
measurement system (i.e. Metric vs. Imperial)
Overall length Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.1
HMDP-HL-10439
-MTHD /
HMDP-HL-10440
-MTHD
1 For Husky and HDX Brand Plastic Tool Box:
As claimed +3% / -0 %,
Overall width Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.2
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
As claimed +3% / -0 %,
Overall height Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.3
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
As claimed + 3% / -0 %,

7 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
2.3 Handle Dimensions CPSD-GB-01056
-MTHD
Report dimensions; shall meet label claims
(if applicable) (±5%).
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.5
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
As claimed + 5% / -5 %,
2.4 Overall Weight CPSD-GB-01056
-MTHD
Report overall weight;
shall meet label claims (if applicable) (±5%)
Overall Weight Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.4
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
As claimed + 3% / -0 %,
2.5 Color CPSD-GB-01057
-MTHD
1 Shall match label claims and/or provided color.

8 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
2.6 Material CPSD-GB-01057
-MTHD
All Assess the material qualities of the components.
From a consumer perspective, ensure that each
of the materials used in the construction of
product appear to be adequate for the intended
use.
Housing of tool box shall appear sturdy and with
adequate structural properties to support the
transporting of tools. Latches shall appear to be
of adequate thickness and hardness for repeated
use. Handle shall appear durable enough for
loaded tool box to be transported without
concern of damage.
2.7 Defects CPSD-GB-01057
-MTHD
1 Shall have no discernible surface degradation,
including crazing, shivering, denting, bubbles,
cracks, stains, deformations, chips, fractures,
heavy lines, waves, shear marks, scratches,
scuff marks, indentations, or blisters.
2.8 Appearance CPSD-GB-01057
-MTHD
All Remove the product from all package materials
and examine the item. Product shall match the
images on submitted package. The product shall
appear to be of an adequate design for intended /
claimed function. If there are aspects of design,
color or other visual aspects that suggest the
product is not adequate for intended use, from a
consumer perspective, comment in results and
include photos to support the observation.
Housing shall not have variations in thickness.
Handle shall appear to be secured properly.
Metal latches shall show no evidence of rust. All
components shall appear acceptable for use.
2.9 Parts inventory
(if applicable)
CPSD-GB-01057
-MTHD
1 All parts shall be provided per claims.

9 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
2.1
0
Sharp Points / Edges 16 CFR 1500.48 /
1500.49 modified
All Shall have no sharp points/edges, other than
those required for function.
Modification = expanded scope to other products
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 3.4
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
The product shall not contain any sharp points or
edges that pose a danger to the user.
2.1
1
Workmanship CPSD-GB-01057
-MTHD
All Product shall not be malformed, shall not be
excessively loose at connections, connections
and fasteners shall not disconnect during normal
handling of the product or during testing.
2.1
2
Squareness CPSD-GB-01056
-MTHD
Measure and report the actual difference
between the internal diagonal lengths.
The difference between the internal diagonal
lengths A and B shall not exceed 0.03 inch per
Figure 1. Report actual calculated difference.
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 7.6
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
The difference between the internal diagonal
lengths A and B shall not exceed 0.03 inch per
Figure 1 in the appendix. Report calculated
difference.

10 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
2.1
3
Hardness Test By 3H Pencil
(For Paint And Coating)
CPSD-HL-05014-
MTHD
Use a 3H hardness pencil to test all coatings.
Gently wipe the surface after testing with a cotton
cloth. Product shall not exhibit obvious scratch
marks, cracks or peeling of coating after testing.
Scratch Resistance Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 3.2
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
Use a 3H hardness pencil to test all coatings.
Gently wipe the surface after testing with a cotton
cloth. Product shall not exhibit obvious scratch
marks, cracks or peeling of coating after testing.
2.1
4
Adhesion Test By 3M
Transparent Tape 600
(For Paint And Coating)
CPSD-HL-03040-
MTHD
A grid of 100 squares of size 1mm x 1mm shall
be scribed through the coating to the substrate
material. “3M” Transparent Tape 600 is attached
to the coating/painting over the grid. Upon
removal of the tape, no more than 10 pieces of
coating may be detached.
Adhesion Test Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 3.3
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
A grid of 100 squares of size 1mm x 1mm shall
be scribed through the coating to the substrate
material. “3M” Transparent Tape 600 is attached
to the coating/painting over the grid. Upon
removal of the tape, no more than 10 pieces of
coating may be detached.
PERFORMANCE TESTS

11 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.1 * Resistance to corrosion ASTM B117-16
modified /
CPSD-HL-01010-
MTHD / ASTM
D610-08 modified
/ client
requirement
[Applicable to samples / sample components
constructed of metal or samples with metallic
coatings]
Withstand 24 hours in 1% salt fog corrosion
chamber followed by steel wool cleaning by
hand. Areas of corrosion shall be cleaned by
rubbing a 0000 grade steel wool back and forth
for 5 cycles over the affected area using only
light pressure. Then rated per ASTM D610 item
must or exceed a grade of 6
Exceptions: If there is a brand product
requirement which overrides procedure and
grading criteria.
Do not test: High Carbon Steel items (such as
Blades, hex keys and bits). If lab has any
questions on whether or not to test item please
contact THD Engineering before conducting test.
Modification = 1% salt spray (fog) for ASTM
B117-16
Modification = Grading evaluation is inclusive of
oxidation / corrosion / tarnishing / visual change
for ASTM D610
Note: Photos of the components before and after
test shall be included in the test report
Client requirement

12 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section
8.11 /
HMDP-HL-10439
-MTHD
1 For Husky Brand Plastic Tool Box:
5% Salt Solution for 48 hours per ASTM B117.
After 48 hours product can be cleaned (per
ASTM B117 product cleaning instruction), no
visible pitting, chipping and cracking visible from
18” and no loss of function per product claims.
Must meet or exceed a minimum corrosion rating
of 6 per ASTM D610.
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.11 /
HMDP-HL-10440
-MTHD
1 For HDX Brand Plastic Tool Box:
5% Salt Solution for 24 hours per ASTM B117.
After 24 hours product can be cleaned (per
ASTM B117 product cleaning instruction), no
visible pitting, chipping and cracking visible from
18” and no loss of function per product claims.
Must meet or exceed a minimum corrosion rating
of 6 per ASTM D610.
3.2 Humidity exposure CPSD-HL-01007-
MTHD
No change after 24 hrs. @ 95% RH @ 100°F.
Report if entire item was placed in the chamber
or if only certain pieces/sections. If
pieces/sections were tested, list which pieces
and include before and after pictures of the
pieces. Product shall not show any evidence of
deterioration, distortion or damage.

13 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.12
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
95% RH @100oF for 24 hours.
Acceptance requirement: No change after 24
hrs. @ 95% RH @ 100°F. Report if entire item
was placed in the chamber or if only certain
pieces/sections. If pieces/sections were
tested, list which pieces and include before
and after pictures of the pieces. Product shall
not show any evidence of deterioration,
distortion or damage.
3.3 Effects of extreme
temperature change
CPSD-HL-01012-
MTHD
24 Hours At 0° F, followed by 24 hours at 120°F.
The sample shall not have any structural failure
or visual changes such as cracks, fractures or
significant aesthetic changes. Products shall
work as intended after the test as compared to
the control.
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.13
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
24 hours @ 0oF followed by 24 hours @ 120oF.
Acceptance requirement: No change after 24
hrs. @ 95% RH @ 100°F. Report if entire item
was placed in the chamber or if only certain
pieces/sections. If pieces/sections were
tested, list which pieces and include before
and after pictures of the pieces. Product shall
not show any evidence of deterioration,
distortion or damage.

14 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.4 Actual use - functionality -
not covered by other tests
CPSD-GB-01058
-MTHD
Shall function as intended as received. Report
details of evaluation (features tested / methods
used / materials used / etc.) Report any features
not evaluated.
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.14
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
Pre-condition the sample to a temperature of 110
F prior to testing. Conduct testing immediately
after removing it from the oven. (i.e. test heated
sample). Using a plastic bag and water to
determine the useable volumetric capacity of the
tool box. The weight of the water shall be
multiplied by 3 times to determine force loading
requirement for pass/fail. With the lower portion
of the sample constrained, and the lid locked in
place, an upward force at a rate of 15 inches per
minute shall be applied across a 4” section of the
handle. Hold the force loading when the pass/fail
limit is reached for 60 seconds. Resume loading,
record and report the force where damage
occurs. Include a photo in report.
Acceptance requirement: Report the
calculated load requirement, and the force at
failure

15 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.5 Handle Strength CPSD-GB-01058
-MTHD
Pre-condition the sample to a temperature of 110
F prior to testing. Conduct testing immediately
after removing it from the oven. (i.e. test heated
sample)
Using a plastic bag and water to determine the
useable volumetric capacity of the tool box. The
weight of the water shall be multiplied by 3 times
to determine force loading requirement for
pass/fail.
Report the calculated load requirement for
handle.
With the lower portion of the sample constrained,
and the lid locked in place, an upward force at a
rate of 15 inches per minute shall be applied
across a 4” section of the handle. Hold the force
loading when the pass/fail limit is reached for 60
seconds. Resume loading, record and report the
force where damage occurs. Include a photo in
report.

16 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.2
/HMDP-HL-104 3
9-MTHD
pass/fail.
handle.
Precondition the sample to a temperature of 110
F. Conduct Testing immediately after removing it
from the oven. With the lower portion of the
sample constrained, and the lid locked in place,
an upward force at a rate of 15 inches per minute
shall be applied across a 4” section of the
handle. Hold the force loading when thepass/fail

17 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.2 /
HMDP-HL-10440
-MTHD
pass/fail.
handle.
Precondition the sample to a temperature of 110
F. Conduct Testing immediately after removing it
from the oven. With the lower portion of the
sample constrained, and the lid locked in place,
an upward force at a rate of 15 inches per minute
shall be applied across a 4” section of the
handle. Hold the force loading when the pass/fail
3.6 * Lock / Latching Durability CPSD-GB-01058
-MTHD
Load ‘tool space’ with bags of metal shot before
test. (the weight of water at full capacity
multiplied by two)
With the base of the sample constrained, the
primary latch shall be fully opened and fully
closed at a rate of 3 (±1) seconds per cycle.
Repeat this process for 5,000 cycles or until a
failure is observed in the latch. (Detachment,
loss of function in the latch, etc.)
The product withstand 5,000 cycles without any
damage or loss of function to the hinge
components

18 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section
8.15 /
HMDP-HL-10439
-MTHD
multiplied by two)
components
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.15 /
HMDP-HL-10440
-MTHD
multiplied by two)
components

19 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.7 Resistance to Compression CPSD-GB-01058
-MTHD
1 [For items without Product Requirement]
A vertical load shall be applied widthwise
(through two 31/2 inch wide boards) across the
top of the sample at a point on each side of the
carry handle centered between outside of handle
and end of box. (a simulation of consumer
standing on the tool box). The force shall be
increased at a rate of 45 inches per minute.
Report the force at damage or yielding
For tool boxes with a width less than 20 inches:
The product shall meet/exceed a 250 Lbf
loading.
For tool boxes with a width 20 inches or greater:
loading.

20 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.4
/HMDP-HL-104 3
9-MTHD
1 [For Husky Brand Plastic Tool Box]
loading.
For tool boxes with a width 20 inches or greater:.
The product shall meet/exceed a 1,000 Lbf
loading.

21 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.4 /
HMDP-HL-10440
-MTHD
1 [For HDX Brand Plastic Tool Box]
loading.
For tool boxes with a width 20 inches or greater:.
The product shall meet/exceed an 850 Lbf
loading.
3.8 Impact Resistance CPSD-HL-01058-
MTHD
1 [For items without Product Requirement]
A steel ball weighing 3 lbs. will be dropped from a
height of 12 inches onto the top of the test
sample. Repeat the drop, increasing the height
by 12 inches each time until it cracks, fractured
or loss of function is observed (unable to open
close due to bending)
Scuffing and denting is acceptable. Report the
max height at which cracking, fracture or loss of
function is noted to occur. Include damage photo
in report.
Must meet/exceed minimum failure height of 3
feet.

22 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.5
/HMDP-HL-104 3
9-MTHD
1 [For Husky Brand Plastic Tool Box]
in report.
feet.
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.5 /
HMDP-HL-10440
-MTHD
1 [For HDX Brand Plastic Tool Box]
in report.
feet.

23 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.9 * Covered compartments CPSD-GB-01058
-MTHD
weight of the water shall be multiplied by 2 to
determine the weight of canvas bags filled with
shot for the test. If there are multiple tiers in the
tool box divide the weight between each level.
The sample shall be loaded with the above test
weight. The sample will then be lifted up by the
carry handle 12 (±1) inches and set back down.
This cycle shall occur at a rate of 10 (±1) cycles
per minute. This shall be repeated for 5,000
cycles or until a failure occurs (damage to
handle). Include photo in report of any damage
and report the total number of cycles.
damage or loss of function to the carry handle.

24 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
* Handle Durability Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.6
/HMDP-HL-104 3
9-MTHD

25 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.6 /
HMDP-HL-10440
-MTHD
3.1
0
* Hinge Durability CPSD-GB-01058
-MTHD
multiplied by two)
With the base of the sample constrained, the lid
shall be fully opened at a rate of 3 (±1) seconds
per cycle.
Fully open, lid must not be supported by any
device.
The lid shall then be fully closed. Repeat this
procedure for 5,000 cycles or until failure. (loss of
function in the hinge)
components.

26 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.7
/HMDP-HL-104 3
9-MTHD
multiplied by two)
shall be opened fully opened at a rate of 3 (±1)
seconds per cycle. Fully open, lid must not be
supported by any device The lid shall then be
fully closed. Repeat this procedure for 10,000
cycles or until failure. (loss of function in the
hinge)
components.
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.7 /
HMDP-HL-10440
-MTHD
multiplied by two)
shall be fully opened at a rate of 3 (±1) seconds
per cycle. Fully open, lid must not be supported
by any device The lid shall then be fully closed.
Repeat this procedure for 5,000 cycles or until
failure. (loss of function in the hinge)
components.

27 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.1
1
Latch Pull CPSD-GB-01058
-MTHD
With the base of the sample constrained, open
the latch fully. Apply a tensile force to the latch in
the upward direction away from the base at a
rate of 15 inches per minute. Hold the force
loading when the pass/fail limit is reached (20 lbf)
for 60 seconds. Resume loading, record and
report the force where the latch is damaged (loss
of function) or removed from the item. Include a
photo in report.
Report the force required to damage / separate
the latch mechanism its attachment location of
the item.
Must meet / exceed minimum failure load of 20
lbf.

28 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.8
/HMDP-HL-104 3
9-MTHD
photo in report.
the item..
lbf.

29 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.8 /
HMDP-HL-10440
-MTHD
photo in report.
the item.
lbf.

30 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.1
2
Drop Test CPSD-HL-01059-
MTHD
1 If the product has a stated weight capacity claim,
load the product with canvas bags filled with shot
equal to the claim. If no claim has been provided,
use a plastic bag and water to determine the
The product shall be dropped from a height of 3
feet onto concrete. The drop orientation shall be
as follows: flat on bottom, 45 degree angle on
one of the short bottom edges, and then on one
of the opposite bottom corners (same face as
hinges).
[For items without Product Requirement]
Product shall remain functional after drop testing.
The product shall not release any components.
Scratches, scuffing or indentation is acceptable.
If product is not functional, add comment and
photo in the test report to demonstrate defect.

31 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section 8.9
/HMDP-HL-104 3
9-MTHD
1 For Husky Brand Plastic Tool Box
If the product has a stated weight capacity claim,
load the product with canvas bags filled with shot
equal to the claim. If no claim has been provided,
use a plastic bag and water to determine the
The product shall be dropped from a height of 3
feet onto concrete. The drop orientation shall be
as follows: flat on bottom, 45 degree angle on
one of the short bottom edges, and then on one
of the opposite bottom corners (same face as
hinges).
For tool boxes with a width 20 inches or greater:
If no failures occur after above method, repeat
method (3 drops) using a drop height of 4 feet.
Follow above method for weight and drop test.
If no failures occur after above method, repeat
method (6 drops) using a drop height of 4 feet.
Product shall remain functional after drop testing.

32 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.9 /
HMDP-HL-10440
-MTHD
1 For HDX Brand Plastic Tool Box
Follow above method for weight and drop test.
3.1
3
Resistance to Chemicals CPSD-GB-01058
-MTHD
The interior surface of the sample shall be
subjected to following liquids/soils for a period of
15 minutes: vehicle brake fluid, grease, gasoline,
ethylene glycol, ethyl alcohol, and engine oil
After 15 minutes, remove the chemicals/soils
using a cotton cloth (and detergent/water as
needed) and review the sample for visible
degradation of surface.
There shall be no permanent deformation,
distortion, bubbling, or other physical defects
after the testing. Note: minor discoloration is
acceptable after testing

33 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HUSKY -
PLASTIC TOOL
BOX - Section
8.10
/HMDP-HL-104 3
9-MTHD
ethylene glycol, ethyl alcohol, and engine oil.
After 24 hours review the sample for visible
degradation.

34 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement -
HDX - PLASTIC
TOOL BOX -
Section 8.10 /
HMDP-HL-10440
-MTHD
1 For HDX Brand Plastic Tool Box]
ethylene glycol, ethyl alcohol, and engine oil.
After 24 hours review the sample for visible
degradation.

35 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
3.1
4
Comfort CPSD-GB-01058
-MTHD
While conducting the performance testing of the
product, assess the handling qualities. Product
shall not cause discomfort during use and shall
allow consumer to maintain control during use.
After loading, grab the carry handle and take
walk for a duration of 5 minutes with the tool box.
The handle shall not cause discomfort during the
5 minute walk.
Open and close the latches / locks. Latches /
locks shall open and close without noticeable
discomfort.

36 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.16
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
1 For Husky and HDX Brand Plastic Tool Box
While conducting the performance testing of the
product, assess the handling qualities. Product
shall not cause discomfort during use and shall
allow consumer to maintain control during use.
After loading, grab the carry handle and take
walk for a duration of 5 minutes with the tool box.
Acceptance requirement: The handle shall
not cause discomfort during the 5 minute
walk. All latches and locks shall function
without discomfort.
3.1
5
Handle rotation durability CPSD-GB-01058
-MTHD
handle shall be moved back and forth its
rotational length at a rate of 3 (±1) seconds per
cycle. Repeat procedure for 5,000 cycles or until
there is a loss of function in the hinge.
The handle shall withstand 5,000 rotational
cycles without loss of function to any of its
components.

37 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section 8.3
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
handle shall be moved back and forth its
rotational length at a rate of 3 (±1) seconds per
cycle. Repeat procedure for 5,000 cycles or until
there is a loss of function in the hinge.
Acceptance requirement: The handle shall
withstand 5,000 rotational cycles without
loss of function to any of its components
3.1
6
Rain intrusion ANSI / UL50
CPSD-EL-01065-
MTHD
The sample shall be subjected to simulated rain,
using a rain apparatus, as follows: Align test
platform so its center is approximately 39 in. (991
mm) horizontally ahead of the center nozzle.
Adjust height of the center nozzle to
approximately 39 in. (991 mm) above the test
platform. Adjust each spray head to 5 psig ±½
psig (34.5 kPa ±4kPa). Once the head pressure
adjustment is complete, run the rain test for 15
±½ minutes
Product interior shall remain dry after rain
intrusion test. Product shall have no loss of
function after test.

38 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.17
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
The sample shall be subjected to simulated rain,
using a rain apparatus, as follows: Align test
platform so its center is approximately 39 in. (991
mm) horizontally ahead of the center nozzle.
Adjust height of the center nozzle to
approximately 39 in. (991 mm) above the test
platform. Adjust each spray head to 5 psig ±½
psig (34.5 kPa ±4kPa). Once the head pressure
adjustment is complete, run the rain test for 15
±½ minutes.
Acceptance requirement: Product interior
shall remain dry after rain intrusion test.
Product shall have no loss of function after
test.
3.1
7
Side wall rigidity CPSD-GB-01058
-MTHD
Measure and report any sidewall deviation of the
sample in the ‘as received’ condition. Fill all of
the available ‘tool space’ with bags of metal shot
and allow sample to sit for 1 hour. Measure and
report any sidewall deviation of the sample in the
‘loaded’ condition.
The sidewall shall remain rigid and not deform
more than 0.25 inch between ‘as received’ and
‘loaded’ conditions.

39 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Home Depot
Requirement –
HDX / HUSKY -
PLASTIC TOOL
BOX - Section
8.18
/HMDP-HL-1043
9-MTHD /
HMDP-HL-10440
-MTHD
Measure and report any sidewall deviation of the
sample in the ‘as received’ condition. Fill all of
the available ‘tool space’ with bags of metal shot
and allow sample to sit for 1 hour. Measure and
report any sidewall deviation of the sample in the
‘loaded’ condition.
Acceptance requirement: The sidewall shall
remain rigid and not deform more than 0.25
inch between ‘asreceived’ and ‘loaded’
conditions.
SAFETY TESTS
4.1 Mechanical Hazards 16 CFR
1500.48/49
1 The sample shall not contain any sharp points or
edges or components that can come into contact
with the user’s hands or body during normal use.
CHEMICAL ANALYSIS
5.1 * DEHP / DINP phthalate
content
CPSC-CH-C1001
-09.3 (Mod) /
CPSD-AN-00095
-MTHD /
CPSD-AN-00143
-MTHD
- Product shall not contain concentrations of more
than 0.1% DEHP/DINP, individually. (1,000ppm)
Testing will be conducted on all accessible
plastics materials. In case of insufficient material
for testing found on number of samples specified
in the protocol, vendor needs to provide
components / parts for testing. Report actual
results or include data table within report.
Component testing is allowed. Compositing up to
3 like materials is allowed.

40 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
5.2 * Total lead in surface
coating
CPSC-CH-E1003
-09.1 /
CPSD-AN-00001
-MTHD
- All accessible surface coatings shall not contain
lead or lead components in which the lead
content is in excess of 0.060% (600ppm) of the
weight of the total content.
In case of insufficient coating for testing found on
number of samples specified in the protocol,
vendor needs to provide additional component
parts (including raw materials) for testing.
Report actual results or include data table within
report. Component testing is allowed.
Based on CPSC SOP, will composite up to 3
colors. If any color in the composite exceeds
80% of the limit (72 ppm), based on the lowest
weight component, individual colors will be
analyzed.
5.3 * Total lead in substrate CPSC-CH-E1001
-08.3 /
CPSC-CH-E1002
-08.3 /
CPSD-AN-00185
-MTHD /
CPSD-AN-00196
-MTHD
- All accessible substrates, before and after use
and abuse testing, on items intended for children
ages 12 and under shall not contain lead in
excess of 0.01% (100ppm) of the weight of the
total content.
In case of insufficient material for testing found
on number of samples specified in the protocol,
vendor needs to provide components/parts for
testing.
Report actual results or include data table within
report.
Issue a third party test report.
Component testing is allowed.
Compositing up to 3 like materials is allowed
except metal.

41 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
OTHER TESTS
6.1 *Brand Logos and Brand
Colors - Color evaluation by
visual examination
HMDP-GB-PTCL
-10030-US-C N-M
X
- Shall meet the applicable requirement as
specified.
Plastic tool box
Image Appendix

42 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
Figure 1.
Squareness
Measurem ents
Required to complete all tests:
Samples Lead Time Cost - US Cost - Asia
3 (Sets) 7 (business days) $ 644.00 $ 736.00
Additional charge:
Claim verification Quote Quote
ANSI verification Quote Quote
NOM labeling certificate review $ 75.00 $ 26.00
Resistance to corrosion (ASTM B117-16 modified / CPSD-HL-01010-MTHD /ASTM
D610-08 modified /clientrequirement) (1%,24 hours)
$ 161.00 * $ 67.00
Lock / Latching Durability $ 150.00 $ 200.00
Covered Compartments $ 100.00 $ 275.00
Hinge Durability $ 100.00 $ 550.00 (Manually)
HMDP-HL-10439-MTHD - section 8.5 - Handle Durability $ 150.00 $ 550.00
HMDP-HL-10439-MTHD - section 8.6 - Hinge Durability $ 150.00
$ 1100.00
(Manually)
HMDP-HL-10439-MTHD - section 8.11 - Corrosion Test $ 356.00 * $ 114.00
HMDP-HL-10439-MTHD - section 8.15 - Lock / Latching Durability $ 250.00 $ 350.00

43 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
HMDP-HL-10440-MTHD - section 8.5 - Handle Durability $ 100.00 $ 275.00
HMDP-HL-10440-MTHD - section 8.6 - Hinge Durability $ 100.00 $ 550.00 (Manually)
HMDP-HL-10440-MTHD - section 8.11 - Corrosion Test $ 214.00 * $ 87.00
HMDP-HL-10440-MTHD - section 8.15 - Lock / Latching Durability $ 150.00 $ 200.00
DEHP / DINP phthalate content Quote $ 123.00 net
Lead in surface coating (per evaluation) $ 79.00 $ 25.00
Lead in substrate (per evaluation) $ 150.00 $ 32.00
Brand Logos and Brand Colors - Color evaluation by visual examination Refer to protocol Refer to protocol
HMDP-GB-PTCL-
10030-US-CN-MX
HMDP-GB-PTCL-1
0030-US-CN-MX
* Above USA prices for testing with ASTM D610 evaluation are for first component only, additional USD 75 will be charged for each additional component
Key:
Results Key:
M Meets NM Does Not Meet
NA Not Applicable NT Not Tested
C Claimed R Recorded
Notes – The definition of the Rating
 Critical – is reserved for defects which could result in hazardous or unsafe conditions for individuals using or maintaining the product as well as defects
contravening legal regulations
 Major – refers to functional defects reducing the usability or solidity of the product as well as obvious visual defects reducing the sales value of theproduct
 Minor – refers to defects that are unlikely to reduce the use of the product, but nevertheless may influence the sale
 Good – no defect found
Revision History
Revision # Date Description THD Approved By SP Revised By
0 4/18/08 Protocol created using HMDP-HL-PTCL-04760-US, prior client specifications, and current
client template.
BVBF-DGE
* Additional Charge For This Test
Only Shaded Lines Are Included For
PoPT Testing.

44 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
1 08-26-09 TPK-09-01657-Revised the test method of “Statement of Quantity” as per Linda Ling BV-SH Eileen
Mou
2 MAY 14,
2010
MAY 14, 2010 – TPK-10-02447 – Added test line “* ANSI verification” as per Elle shen due to
client request by YauKin Chiu.
YauKin Chiu.
3 JULY 05,
2010
JULY 05, 2010 – TPK-10-03913 – Revised the criteria of test line “ANSI verification” by
adding note “Must be recorded as Pass, Fail or Not Claimed.” And “or NA (Not Applicable)”
after “Do not put in NP (No Packaging)” as per Jeff Kornreich and Tony Depa by YauKin
Chiu.
BV-KC
YauKin Chiu.
4 JULY 19,
2010
JULY 19, 2010 – TPK-10-04290 – Added test line “CARB documentation and label review”
[Client Requirement: Expanded scope to other countries.] as per B.Murty/Adam
Davies/Massi/John Rudolph by Winky Cheung.
BV-HK-KC
Winky Cheung.
5 DECEMBE
R 08, 2010
DECEMBER 08, 2010 – TPK-10-07145 – Update protocol format follow client template
(added Numbering of Test Lines) as per Deena Cotterill by YauKin Chiu.
BV-KC
YauKin Chiu.
6 MARCH
21, 2011
MARCH 21, 2011 – TPK-11-00366 – Deleted test “CARB documentation and label review”
from CN and MX protocols as per AsiaTechInquiryMail/Deena Cotterill by Carol SL Cheung.
BV-KC
Carol SL
Cheung.
7 JUNE 02,
2011
JUNE 02, 2011 – TPK-11-03262 – Deleted test “Total lead content in surface coatings” to all
Department 25 protocols (tools) for US, CN and MX as per Deena Cotterill by Belinda Chu.
JUNE 14, 2011 /
Wang, Fred
BV-HK-KC
Belinda Chu
8 JULY 04,
2011
JULY 04, 2011 – TPK-11-03865 - Added test “CARB formaldehyde document and label
review” to MX/CN protocols as per Deena Cotterill / Xeri by Eric MH Wong. (Carol SL
Cheung)
JULY 05, 2011 /
Deena Cotterill
BV-KC
Carol SL
Cheung.
9 SEPTEMB
ER 09,
2011
SEPTEMBER 09, 2011 – TPK-11-02957 – Added protocol note “All the information and
claims on the PQOB should be verified and recorded in protocol.” As per Deena
Cotterill/Jerry Liu by Eric MH Wong. (Carol SL Cheung)
JULY 05, 2011
Deena Cotterill
BV-HK-KC
Carol SL
Cheung
10 OCTOBER
10, 2011
OCTOBER 10, 2011 – TPK-11-05240 – Added labeling note “Note: For PPT (Pre-Purchase
Test), report as N/A if no retail package or artwork was provided” as per Kenneth Ho by Eric
MH Wong.( Wing-WY Lau)
OCTOBER 12,
2011 / John Bocek
BV-HK-KC
Wing-WY Lau
11 JUNE 22,
2012
MAY 8, 2012 – TPK-12-02987 – add detest ‘Base Durability’ to cover product have seating
function as per Jerry Liu, revised citation for test “Handle strength” from EL-1050 to
HL-1058 , revert to 3 level format by Chun Kit Yuen
JUNE 22, 2012 – TPK-12-03567 – Project request for revision of Corrosion test for D25
item – revised citation for Corrosion test by add ASTM D610 and revised criteria by added
grading evaluation for ASTM D610 as per Kenneth Ho due to client request by Chun Kit
Yuen
JULY 03, 2012
Jeff Kornreich
BV-HK-KC
Chun Kit Yuen

45 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
12 MARCH
06, 2013
MARCH 06, 2013 – TPK-12-10113 – Revised protocol TAT to 7 business days as per Kasey
Doty by Jason Siu
BV-SZ
Jason Siu
13 JUNE 11,
2013
JUNE 11, 2013 – TPK-13-02880 – added test “Brand Logos and Brand Colors – Color
evaluation by visual examination” as per Ka Man Wu & Kasey Doty due to client request by
Chun Kit Yuen
BV-HK-KC
Chun-Kit Yuen
14 AUGUST
15, 2013
AUGUST 15, 2013-TPK-13-06450 – Added 10030 supplemental protocol and removed
“Brand Logos and Brand Colors – Color evaluation by visual examination” test as per Ka
Man Wu by Sylvia Huang
BV-SZ
Sylvia Huang
15 SEPTEMB
ER 13,
2013
SEPTEMBER 13, 2013 – TPK 13-06984 – Added test “Accuracy of order or number for
bilingual instructions / packaging” under “LABELING & MARKING VERIFICATION” due to
client require as per Kenneth Ho by William-A Wu.
SEPTEMBER 13, 2013 – TPK 13-07098 – Revised key in the note of “LABELING &
MARKING VERIFICATION” from “N/A” to “UNSAT” due to Technical Change as per
Kenneth Ho by William-A Wu.
SEPTEMBER 13, 2013 – TPK 13-07406 – Added key specifications “M”, “NM”, “NA”, “NT”,
“C”, “R” due to BV-Lab requirement as per Kenneth Ho by William-A Wu.
BV-SZ
William-A Wu
16 DECEMBE
R 18, 2013
DECEMBER 18, 2013 – TPK-13-10128 – Revised protocol from 3-level format to non-3-level
format due to client requirement as per Kenneth Ho by Yu-Y Chan.
JANUARY 08, 2014
/ Kenneth Ho
BV-HK-KB
Yu-Y Chan
17 APRIL 2,
2014
JANUARY 10, 2014 – TPK-14-00164R – Revised “Moisture Content” test and added back
statement “composite” in the criteria of “CARB formaldehyde document and label review” in
Labeling of US, CN and MX as per client requirement by Phil Ma.
APRIL 2, 2014 – TPK-14-02658 – Revised all PQOB to PLM as per Kenneth Ho by Justin H
Wei.
MAY 12, 2014 /
Kenneth Ho
BV-SZ
Justin H Wei
18 JUNE 09,
2014
JUNE 09, 2014 – TPK-14-03905 – Added back protocol scope as per Chun-Kit Yuen by Phil
Ma.
JULY 09, 2014 /
Kenneth Ho
BV-SZ
Phil Ma
19 AUGUST
01, 2014
AUGUST 01, 2014 – TPK-13-08019 – remove “CARB formaldehyde document and label
review” test and replace with “CARB certificate review” for US/CN/MX as per Kenneth Ho
due to client request by Chun Kit Yuen
AUGUST 08, 2014 /
Kasey C. Doty
BV-HK-KB
Chun Kit Yuen
20 SEPTEMB
ER 03,
2014
SEPTEMBER 03, 2014 – TPK-14-06858 – added noted “Photos of the components before
and after test shall be included in the test report” to all kinds of corrosion test as per Humbert
Man due to client request by Chun Kit Yuen
SEPTEMBER15,
2014 / Jerry Meng
BV-HK-KB
Chun Kit Yuen
21 DECEMBE
R 01, 2014
DECEMBER 01, 2014 – TPK-14-09859 – Revised “Barcode requirement” test line as per
Kenneth Ho (John Cutts) by Phil Ma.
DECEMBER 04,
2014 / Kathy Kube
BV-SZ
Phil Ma

46 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
22 APRIL 20,
2015
APRIL 20, 2015- TPK-15-02730- Updated “CARB test line” by adding “the certified date
should within one(1) year…” , “Note: Photo of the certification shall be included in the test
report.” in criteria as per Humbert Man by Ivy Liu
APRIL 22, 2015 /
Kenneth Ho
BV-SZ
Ivy Liu
23 JULY 30,
2015
JULY 30, 2015 – TPK-15-05636 – Removed “Labeling –Packaging (If Applicable)”,
“Warranty Claim”, “Carton Check” test as per Alice Yip by Sa Cen.
AUGUST 03, 2015 /
Kenneth Ho
BV-SZ
Sa Cen
24 DECEMBE
R 21, 2015
DECEMBER 21, 2015 – TPK-15-10081 – Added internal method in CARB testline as per
Humbert Man by Bob Chen.
DECEMBER 28,
2015 / Kenneth Ho
BV-SZ
Bob Chen
25 JULY 11,
2016
JULY 11, 2016 - TPK-16-05441 - Updated standard ASTM B117 to 2016 version as per
Belinda Chu by Phil Ma. [F16-116]
JULY 20, 2016/
Kathy Kube
BV-SZ
Phil Ma
26 SEPTEMB
ER 20,
2017
SEPTEMBER 20, 2017 - TPK-17-09717 - Added "NOM labeling certificate review" test as
per Michael Wu (James Li) by Phil Ma.
SEPTEMBER 10,
2017 / James Li
BV-SZ
Phil Ma
27 OCTOBER
09, 2017
OCTOBER 09, 2017 - TPK-17-10181 - Added FlexPLM - Certification & Safety Verification
as per Michael Wu (Andy Chan) by Ivan Lee
SEPTEMBER 15,
2017 / Awudu
Mama & Andy Chan
BV-HK-KB
Ivan Lee

47 of 47
The Home Depot
PPT PROTOCOL #
HMDP-HL-PT
CL-04760-MX
PROTOCOL NAME
SP NAME
28 JUNE 19,
2017
JUNE 19, 2017 - TPK-17-05831 - Added PR-10439 (Husky) for Plastic Tool Box tests as per
Humbert Man (Nikita Li) by Phil Ma.
JUNE 23, 2017 - TPK-17-05831R - Add PR-10440 (HDX) tests: "Overall length", "Overall
width", "Overall height", "Overall weight", "Squareness", "Resistance to corrosion", "Handle
Strength", "Resistance to Compression", "Impact Resistance", "Handle Durability", "Hinge
Durability", "Latch Pull (If not riveted or bolted down)", "Drop Test", "Resistance to
Chemical";
To aligned with client’s provided ITS drafts: Added "Hardness Test By 3H Pencil", "Adhesion
Test By 3M Transparent Tape 600";
Per AME's comment, changed protocol title to "Portable Tool Box" from "Tool Box", revised
"Material" test per template, added "Appearance" and "Comfort" test per template, added
statement "shall be measured / reported as per claimed measurement system (i.e. Metric vs.
Imperial)" in "Overall length", "Overall width", "Overall height" and "Overall weight", updated
"Parts inventory" test, updated "Humidity exposure" and "Effects of extreme temperature
change" tests, removed "Handle Shock Load" test, Updated "Lock / Latching Durability" test
and add Husky&HDX PR tests, replaced "Sharp Points / Edges" with "Mechanical Hazards"
test and moved the test to SAFETY TESTS category;
Due to lab's capability limitation, changed rate of upward force in "Handle Strength" test from
"200 inches per minute" to "15 inches per minute" by Phil Ma.
JULY 14, 2017 - TPK-17-05831R - Per AME's comment: Removed "CARB", "Base
Durability", original "Lock / Latching Durability", "Cold Drop Test" tests, added new "Lock /
Latching Durability", "Handle rotation durability", "Rain intrusion", "Covered compartments,
durability", "Side wall rigidity", "Mechanical Hazards" (keep Sharp Points / Edges test),
"DEHP / DINP phthalate content", "Total lead in surface coating" and "Total lead in
substrate" tests as per Travis Norton by Phil Ma.
JULY 26, 2017/
Brice Weeter
BV-SZ
Phil Ma
29 DECEMBE
R 05, 2017
DECEMBER 05, 2017 – TPK-17-13268 – Revised criteria of Actual use - functionality - not
covered by other tests and handle strength test to 3 times max water capacity as per Rodney
Wells (Brice Weeter) by Ivan Lee
DECEMBER 12,
2017/ Brice Weeter
BV-HK-KB
Ivan Lee

Hmdp hl-ptcl-04760-mx-portable tool box-v30

Recommended

Recommended

More Related Content

Similar to Hmdp hl-ptcl-04760-mx-portable tool box-v30

Similar to Hmdp hl-ptcl-04760-mx-portable tool box-v30 (20)

Recently uploaded

Recently uploaded (20)

Hmdp hl-ptcl-04760-mx-portable tool box-v30