This document summarizes a strategy for choosing optimal process parameters for operating a nutrient mist reactor to grow hairy roots. It presents a theoretical model and numerical simulations.
The model describes the evolution of liquid holdup and nutrient concentration in the root bed under intermittent misting cycles. Guidelines are provided for selecting the feed concentration, flow rate, and durations of mist-ON and mist-OFF cycles. Numerical simulations show that the reactor can be run with very low cumulative mist-ON duration (e.g. 10% of total time) while keeping the mist-OFF for most of the time (e.g. 90%), to prevent nutrient deficiency or waterlogging in the root bed. The optimal durations of misting cycles depend on
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
High Speed Fault Injection Tool (FITO) Implemented With VHDL on FPGA For Test...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Fuzzy soft set is one of the recent topics developed for dealing with the uncertainties present
in most of our real life situations. The parameterization tool of soft set theory enhances the flexibility of
its application. In this paper, we have studied membership grade, power set,
-cut set , strong fuzzy
-
cut set ,some standard operation fuzzy soft set, degree of subset hood and proposed some results with
examples.
Removal of Clutter by Using Wavelet Transform For Wind ProfilerIJMER
ABSTRACT: Removal of clutter in the radar wind profiler
is the utmost important consideration in radar. Wavelet
transform is very effective method to remove the clutter.
This paper presents a technique based on the wavelet
transform to remove the clutter. In this technique we used
Fourier transform and descrete wavelet transform after
that applied inverse discrete wavelet transform for signal.
These techniques applied for inphase and quadrature
phase, total spectrum and single range gate. Very
encouraging results got with this technique that have
shown practical possibilities for a real time
implementation and for applications related to frequency
domain.
Keywords: Wind profiler, wavelet transform, Fourier transform, clutter, signal processing
A Novel Approach To Answer Continuous Aggregation Queries Using Data Aggregat...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
The determination of this paper is to introduce two new spaces , namely 𝑆𝑔
∗
-compact and 𝑆𝑔
∗
-
connected spaces. Additionally some properties of these spaces are investigated.
Mathematics Subject Classification: 54A05
Review of research on bio reactors used in wastewater ijsit 2.4.6IJSIT Editor
The review presented in this paper focuses on reactors used in wastewater treatment for bio
hydrogen production (e.g. batch reactors, complete mix reactors, plug flow reactors, bio-film reactors,
suspended reactors, upflow anaerobic sludge blanket reactor, anaerobic baffled reactors, upflow packed-bed
attached growth reactors, attached growth fluidized bed reactors, anaerobic sequencing batch reactor, hybrid
/ high rate reactors and membrane separation reactors. It is clear from the review that development of these
reactors can be considered a grown up research for which good design and scale-up guidelines are available
High Speed Fault Injection Tool (FITO) Implemented With VHDL on FPGA For Test...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Fuzzy soft set is one of the recent topics developed for dealing with the uncertainties present
in most of our real life situations. The parameterization tool of soft set theory enhances the flexibility of
its application. In this paper, we have studied membership grade, power set,
-cut set , strong fuzzy
-
cut set ,some standard operation fuzzy soft set, degree of subset hood and proposed some results with
examples.
Removal of Clutter by Using Wavelet Transform For Wind ProfilerIJMER
ABSTRACT: Removal of clutter in the radar wind profiler
is the utmost important consideration in radar. Wavelet
transform is very effective method to remove the clutter.
This paper presents a technique based on the wavelet
transform to remove the clutter. In this technique we used
Fourier transform and descrete wavelet transform after
that applied inverse discrete wavelet transform for signal.
These techniques applied for inphase and quadrature
phase, total spectrum and single range gate. Very
encouraging results got with this technique that have
shown practical possibilities for a real time
implementation and for applications related to frequency
domain.
Keywords: Wind profiler, wavelet transform, Fourier transform, clutter, signal processing
A Novel Approach To Answer Continuous Aggregation Queries Using Data Aggregat...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
The determination of this paper is to introduce two new spaces , namely 𝑆𝑔
∗
-compact and 𝑆𝑔
∗
-
connected spaces. Additionally some properties of these spaces are investigated.
Mathematics Subject Classification: 54A05
Review of research on bio reactors used in wastewater ijsit 2.4.6IJSIT Editor
The review presented in this paper focuses on reactors used in wastewater treatment for bio
hydrogen production (e.g. batch reactors, complete mix reactors, plug flow reactors, bio-film reactors,
suspended reactors, upflow anaerobic sludge blanket reactor, anaerobic baffled reactors, upflow packed-bed
attached growth reactors, attached growth fluidized bed reactors, anaerobic sequencing batch reactor, hybrid
/ high rate reactors and membrane separation reactors. It is clear from the review that development of these
reactors can be considered a grown up research for which good design and scale-up guidelines are available
It is strongly felt the need to replace fossil fuels with other renewable and more compatible with the environment. The spinneret of algal crops is
producing different solutions ("open ponds", tubular, bioreactors in greenhouses, etc.). The aim is to obtain concentrations of dry substance such as to
justify the high costs of extraction. Another limitation suffered by the actual plants, derives from the choice to move the algal mass (process
characterized by a high energy consumption), with actions necessary to keep it in suspension as well as to move it, to exchange its positioning in order
to bring it to be conditioned by the light (exhausting its effectiveness after the first 0.2-0.3 m of algal mass depth, or even less if thicker and when it
would need more light for its exponential growth). In particular, it is not possible to bring a specific radiation spectrum, in a pervasive and deep way,
with a drastic cost reduction for the mechanical movement of the culture medium. A limitation derives also from the possibility of biological and
chemical contamination from the environment, because the algal mass is in a large contact with the environment itself (e.g. the "open ponds"
situations) and it is heavily exposed to the prevalent thermal cycles (often not suitable to the processes of growth) inside it. Some problems are often
encountered even in the phase of collection and selection of the algal mass to be forwarded to the following processes, that proceeds through the
massive processing of large volumes (by filtration and concentration) that, due to previous limitations (contamination and uncertain conditions of
growth), remain at low concentrations. The purpose of this article is to present the PBRC (Photo Bio Reactor Continuous) plant, subject of an
Italian patent [Lavanga and Farné, 2014], for the cultivation of microalgae, from which to extract an oleic fraction, which can be destined for
production of biofuels, and a protein fraction, which can be destined for use in the chemical, agri-food, pharmaceutical and cosmetic sectors.
Hybridization of desalination processesIJERA Editor
The aim of any new or improved technique in the water production technology may concentrate in water quality , production rates and coasts of production .In this paper we will talk about the hybridization of desalination process intending to enhance the effectiveness of the productionprocedure.. Hybridization of a dependable production process such as Multi-Stage Flash (MSF) and a well improved and introduced technology such as Membrane-based process is an upcoming trend for maximizing the recovery ratio and quality for the process, in addition to the economical benefits that it will offer. This paper will discuss examples of different hybrid systems.
A Study on Translucent Concrete Product and Its Properties by Using Optical F...IJMER
- Translucent concrete is a concrete based material with light-transferring properties,
obtained due to embedded light optical elements like Optical fibers used in concrete. Light is conducted
through the concrete from one end to the other. This results into a certain light pattern on the other
surface, depending on the fiber structure. Optical fibers transmit light so effectively that there is
virtually no loss of light conducted through the fibers. This paper deals with the modeling of such
translucent or transparent concrete blocks and panel and their usage and also the advantages it brings
in the field. The main purpose is to use sunlight as a light source to reduce the power consumption of
illumination and to use the optical fiber to sense the stress of structures and also use this concrete as an
architectural purpose of the building
Developing Cost Effective Automation for Cotton Seed DelintingIJMER
A low cost automation system for removal of lint from cottonseed is to be designed and
developed. The setup consists of stainless steel drum with stirrer in which cottonseeds having lint is mixed
with concentrated sulphuric acid. So lint will get burn. This lint free cottonseed treated with lime water to
neutralize acidic nature. After water washing this cottonseeds are used for agriculter purpose
Study & Testing Of Bio-Composite Material Based On Munja FibreIJMER
The incorporation of natural fibres such as munja fiber composites has gained
increasing applications both in many areas of Engineering and Technology. The aim of this study is to
evaluate mechanical properties such as flexural and tensile properties of reinforced epoxy composites.
This is mainly due to their applicable benefits as they are light weight and offer low cost compared to
synthetic fibre composites. Munja fibres recently have been a substitute material in many weight-critical
applications in areas such as aerospace, automotive and other high demanding industrial sectors. In
this study, natural munja fibre composites and munja/fibreglass hybrid composites were fabricated by a
combination of hand lay-up and cold-press methods. A new variety in munja fibre is the present work
the main aim of the work is to extract the neat fibre and is characterized for its flexural characteristics.
The composites are fabricated by reinforcing untreated and treated fibre and are tested for their
mechanical, properties strictly as per ASTM procedures.
Hybrid Engine (Stirling Engine + IC Engine + Electric Motor)IJMER
Hybrid engine is a combination of Stirling engine, IC engine and Electric motor. All these 3 are
connected together to a single shaft. The power source of the Stirling engine will be a Solar Panel. The aim of
this is to run the automobile using a Hybrid engine
Fabrication & Characterization of Bio Composite Materials Based On Sunnhemp F...IJMER
The present day technology demands eco-friendly developments. In this era the
composite material are playing a vital roal in different field of Engineering .The composite materials
are using as a principle materials. Nowaday the composite materials are utilizing as a important
component of engineering field .Where as the importance of the applications of composites is well
known, but thrust on the use of natural fibres in it for reinforcement has been given priority for some
times. But changing from synthetic fibres to natural fibres provides only half green-composites. A
partial green composite will be achieved if the matrix component is also eco-friendly. Keeping this in
view, a detailed literature surveyed has been carried out through various issues of the Journals
related to this field. The material systems used are sunnhemp fibres. Some epoxy and hardener has
been also added for stability and drying of the bio-composites. Various graphs and bar-charts are
super-imposed on each other for comparison among themselves and Graphs is plotted on MAT LAB
and ORIGIN 6.0 software. To determining tensile strengths, Various properties for different biocomposites
have been compared among themselves. Comparison of the behaviour of bio-composites of
this work has been also compare with other works. The bio-composites developed in this work are
likely to get applications in fall ceilings, partitions, bio-degradable packagings, automotive interiors,
sports things (e.g. rackets, nets, etc.), toys etc.
Geochemistry and Genesis of Kammatturu Iron Ores of Devagiri Formation, Sandu...IJMER
The Greenstone belts of Karnataka are enriched in BIFs in Dharwar craton, where Iron
formations are confined to the basin shelf, clearly separated from the deeper-water iron formation that
accumulated at the basin margin and flanking the marine basin. Geochemical data procured in terms of
major, trace and REE are plotted in various diagrams to interpret the genesis of BIFs. Al2O3, Fe2O3 (T),
TiO2, CaO, and SiO2 abundances and ratios show a wide variation. Ni, Co, Zr, Sc, V, Rb, Sr, U, Th,
ΣREE, La, Ce and Eu anomalies and their binary relationships indicate that wherever the terrigenous
component has increased, the concentration of elements of felsic such as Zr and Hf has gone up. Elevated
concentrations of Ni, Co and Sc are contributed by chlorite and other components characteristic of basic
volcanic debris. The data suggest that these formations were generated by chemical and clastic
sedimentary processes on a shallow shelf. During transgression, chemical precipitation took place at the
sediment-water interface, whereas at the time of regression. Iron ore formed with sedimentary structures
and textures in Kammatturu area, in a setting where the water column was oxygenated.
Experimental Investigation on Characteristic Study of the Carbon Steel C45 in...IJMER
In this paper, the mechanical characteristics of C45 medium carbon steel are investigated
under various working conditions. The main characteristic to be studied on this paper is impact toughness
of the material with different configurations and the experiment were carried out on charpy impact testing
equipment. This study reveals the ability of the material to absorb energy up to failure for various
specimen configurations under different heat treated conditions and the corresponding results were
compared with the analysis outcome
Non linear analysis of Robot Gun Support Structure using Equivalent Dynamic A...IJMER
Robot guns are being increasingly employed in automotive manufacturing to replace
risky jobs and also to increase productivity. Using a single robot for a single operation proves to be
expensive. Hence for cost optimization, multiple guns are mounted on a single robot and multiple
operations are performed. Robot Gun structure is an efficient way in which multiple welds can be done
simultaneously. However mounting several weld guns on a single structure induces a variety of
dynamic loads, especially during movement of the robot arm as it maneuvers to reach the weld
locations. The primary idea employed in this paper, is to model those dynamic loads as equivalent G
force loads in FEA. This approach will be on the conservative side, and will be saving time and
subsequently cost efficient. The approach of the paper is towards creating a standard operating
procedure when it comes to analysis of such structures, with emphasis on deploying various technical
aspects of FEA such as Non Linear Geometry, Multipoint Constraint Contact Algorithm, Multizone
meshing .
Static Analysis of Go-Kart Chassis by Analytical and Solid Works SimulationIJMER
This paper aims to do modelling, simulation and performing the static analysis of a go
kart chassis consisting of Circular beams. Modelling, simulations and analysis are performed using 3-D
modelling software i.e. Solid Works and ANSYS according to the rulebook provided by Indian Society of
New Era Engineers (ISNEE) for National Go Kart Championship (NGKC-14).The maximum deflection is
determined by performing static analysis. Computed results are then compared to analytical calculation,
where it is found that the location of maximum deflection agrees well with theoretical approximation but
varies on magnitude aspect.
In récent year various vehicle introduced in market but due to limitation in
carbon émission and BS Séries limitd speed availability vehicle in the market and causing of
environnent pollution over few year There is need to decrease dependancy on fuel vehicle.
bicycle is to be modified for optional in the future To implement new technique using change in
pedal assembly and variable speed gearbox such as planetary gear optimise speed of vehicle
with variable speed ratio.To increase the efficiency of bicycle for confortable drive and to
reduce torque appli éd on bicycle. we introduced epicyclic gear box in which transmission done
throgh Chain Drive (i.e. Sprocket )to rear wheel with help of Epicyclical gear Box to give
number of différent Speed during driving.To reduce torque requirent in the cycle with change in
the pedal mechanism
Integration of Struts & Spring & Hibernate for Enterprise ApplicationsIJMER
The proposal of this paper is to present Spring Framework which is widely used in
developing enterprise applications. Considering the current state where applications are developed using
the EJB model, Spring Framework assert that ordinary java beans(POJO) can be utilize with minimal
modifications. This modular framework can be used to develop the application faster and can reduce
complexity. This paper will highlight the design overview of Spring Framework along with its features that
have made the framework useful. The integration of multiple frameworks for an E-commerce system has
also been addressed in this paper. This paper also proposes structure for a website based on integration of
Spring, Hibernate and Struts Framework.
Microcontroller Based Automatic Sprinkler Irrigation SystemIJMER
Microcontroller based Automatic Sprinkler System is a new concept of using
intelligence power of embedded technology in the sprinkler irrigation work. Designed system replaces
the conventional manual work involved in sprinkler irrigation to automatic process. Using this system a
farmer is protected against adverse inhuman weather conditions, tedious work of changing over of
sprinkler water pipe lines & risk of accident due to high pressure in the water pipe line. Overall
sprinkler irrigation work is transformed in to a comfortableautomatic work. This system provides
flexibility & accuracy in respect of time set for the operation of a sprinkler water pipe lines. In present
work the author has designed and developed an automatic sprinkler irrigation system which is
controlled and monitored by a microcontroller interfaced with solenoid valves.
On some locally closed sets and spaces in Ideal Topological SpacesIJMER
In this paper we introduce and characterize some new generalized locally closed sets
known as
δ
ˆ
s-locally closed sets and spaces are known as
δ
ˆ
s-normal space and
δ
ˆ
s-connected space and
discussed some of their properties
Intrusion Detection and Forensics based on decision tree and Association rule...IJMER
This paper present an approach based on the combination of, two techniques using
decision tree and Association rule mining for Probe attack detection. This approach proves to be
better than the traditional approach of generating rules for fuzzy expert system by clustering methods.
Association rule mining for selecting the best attributes together and decision tree for identifying the
best parameters together to create the rules for fuzzy expert system. After that rules for fuzzy expert
system are generated using association rule mining and decision trees. Decision trees is generated for
dataset and to find the basic parameters for creating the membership functions of fuzzy inference
system. Membership functions are generated for the probe attack. Based on these rules we have
created the fuzzy inference system that is used as an input to neuro-fuzzy system. Fuzzy inference
system is loaded to neuro-fuzzy toolbox as an input and the final ANFIS structure is generated for
outcome of neuro-fuzzy approach. The experiments and evaluations of the proposed method were
done with NSL-KDD intrusion detection dataset. As the experimental results, the proposed approach
based on the combination of, two techniques using decision tree and Association rule mining
efficiently detected probe attacks. Experimental results shows better results for detecting intrusions as
compared to others existing methods
Natural Language Ambiguity and its Effect on Machine LearningIJMER
"Natural language processing" here refers to the use and ability of systems to process
sentences in a natural language such as English, rather than in a specialized artificial computer
language such as C++. The systems of real interest here are digital computers of the type we think of as
personal computers and mainframes. Of course humans can process natural languages, but for us the
question is whether digital computers can or ever will process natural languages. We have tried to
explore in depth and break down the types of ambiguities persistent throughout the natural languages
and provide an answer to the question “How it affects the machine translation process and thereby
machine learning as whole?” .
Today in era of software industry there is no perfect software framework available for
analysis and software development. Currently there are enormous number of software development
process exists which can be implemented to stabilize the process of developing a software system. But no
perfect system is recognized till yet which can help software developers for opting of best software
development process. This paper present the framework of skillful system combined with Likert scale. With
the help of Likert scale we define a rule based model and delegate some mass score to every process and
develop one tool name as MuxSet which will help the software developers to select an appropriate
development process that may enhance the probability of system success.
Material Parameter and Effect of Thermal Load on Functionally Graded CylindersIJMER
The present study investigates the creep in a thick-walled composite cylinders made
up of aluminum/aluminum alloy matrix and reinforced with silicon carbide particles. The distribution
of SiCp is assumed to be either uniform or decreasing linearly from the inner to the outer radius of
the cylinder. The creep behavior of the cylinder has been described by threshold stress based creep
law with a stress exponent of 5. The composite cylinders are subjected to internal pressure which is
applied gradually and steady state condition of stress is assumed. The creep parameters required to
be used in creep law, are extracted by conducting regression analysis on the available experimental
results. The mathematical models have been developed to describe steady state creep in the composite
cylinder by using von-Mises criterion. Regression analysis is used to obtain the creep parameters
required in the study. The basic equilibrium equation of the cylinder and other constitutive equations
have been solved to obtain creep stresses in the cylinder. The effect of varying particle size, particle
content and temperature on the stresses in the composite cylinder has been analyzed. The study
revealed that the stress distributions in the cylinder do not vary significantly for various combinations
of particle size, particle content and operating temperature except for slight variation observed for
varying particle content. Functionally Graded Materials (FGMs) emerged and led to the development
of superior heat resistant materials.
Energy Audit is the systematic process for finding out the energy conservation
opportunities in industrial processes. The project carried out studies on various energy conservation
measures application in areas like lighting, motors, compressors, transformer, ventilation system etc.
In this investigation, studied the technical aspects of the various measures along with its cost benefit
analysis.
Investigation found that major areas of energy conservation are-
1. Energy efficient lighting schemes.
2. Use of electronic ballast instead of copper ballast.
3. Use of wind ventilators for ventilation.
4. Use of VFD for compressor.
5. Transparent roofing sheets to reduce energy consumption.
So Energy Audit is the only perfect & analyzed way of meeting the Industrial Energy Conservation.
An Implementation of I2C Slave Interface using Verilog HDLIJMER
The focus of this paper is on implementation of Inter Integrated Circuit (I2C) protocol
following slave module for no data loss. In this paper, the principle and the operation of I2C bus protocol
will be introduced. It follows the I2C specification to provide device addressing, read/write operation and
an acknowledgement. The programmable nature of device provide users with the flexibility of configuring
the I2C slave device to any legal slave address to avoid the slave address collision on an I2C bus with
multiple slave devices. This paper demonstrates how I2C Master controller transmits and receives data to
and from the Slave with proper synchronization.
The module is designed in Verilog and simulated in ModelSim. The design is also synthesized in Xilinx
XST 14.1. This module acts as a slave for the microprocessor which can be customized for no data loss.
Discrete Model of Two Predators competing for One PreyIJMER
This paper investigates the dynamical behavior of a discrete model of one prey two
predator systems. The equilibrium points and their stability are analyzed. Time series plots are obtained
for different sets of parameter values. Also bifurcation diagrams are plotted to show dynamical behavior
of the system in selected range of growth parameter
Discrete Model of Two Predators competing for One Prey
H04014654
1. International Journal of Engineering Inventions
e-ISSN: 2278-7461, p-ISSN: 2319-6491
Volume 4, Issue 1 (July 2014) PP: 46-54
www.ijeijournal.com Page | 46
A strategy to choose process parameters for sustained operation
of nutrient mist reactor to grow hairy roots
Ritu Ranjan1
, Sambashiva Katuri Rao2
, Rajesh Khanna3
1,2,3
Department of Chemical Engineering, Indian Institute of Technology Delhi ( I.I.T.Delhi ), New Delhi -
110016, India
Abstract: Feed concentration and feed flow rate along with the relative durations of the mist-ON/ mist-OFF
cycles are the important process parameters for the growth of hairy roots in a nutrient mist reactor. The paper
presents guidelines for choosing these parameters for an efficient operation of the reactor with intermittent
mist-ON/mist-OFF cycles. It is based on a theoretical model of nutrient mist reactor at the root bed level and its
numerical simulation. This model describes the evolution of liquid holdup and concentration present in the root
bed. One can also run the reactor with intermittent mist-ON and mist-OF cycles, at very low cumulative mist-
ON duration for any given total run time to prevent any nutrient deficiency and water logging in the bed. It is
found that in some conditions mist has to be switched on for only about 10% of the total runtime while the mist
can be switched off for 90% of the total run time. The duration of both mist-ON / mist-OFF cycles are effected
by the process parameters and thus, the ratio of mist-ON time to total run time, may not follow any fixed trend
in some cases. The guidelines presented here will help in efficient operation and design of nutrient mist
reactors.
Keywords: Drainage rate, hairy root, mist deposition, mist-ON cycle/mist-OFF cycle, saturation.
I. Introduction
Hairy root culture are of particular interest for the production of high-value plant secondary metabolites
because these cultures are genetically stable, grow rapidly, and produce a spectrum and quantity of secondary
metabolites similar to that of the parent plant (Aird, 1988). Hairy roots produced by genetic transformation with
Agrobacterium rhizogenes are a potential means for manufacture of plant secondary metabolites (Verma and
Singh, 2008; Ferreira, 2005; and Kim, 2002). These can be generated from a large variety of species (Guillon,
2006) and a source of many important phytochemicals (Wyslouzil, 19997; Carvalho, 1998; Kim, 2001; Sudha,
2003; Weathers, 2005; and Lorence, 2004). Hairy root cultures have gained importance because of their stability
and ability to grow in a hormone free medium (Souret, 2003; Shanks, 1999; Sevon, 2002; and Parr, 1988). Their
root growth is very complicated due to its dense root
network and, branching processes (Sharp, 1990).
The unique growth pattern and fragile nature of hairy roots have led to many different reactor
configurations to avoid injuring the roots while optimizing the supply of nutrients and gases (Ranjan, 2008;
Srivastava, 2007; Sivakumar, 2006; Eibl, 2006; McAlister, 2005; Palazon, 2003; Pavlov, 2005; Pavlov, 2006;
Hilton, 1990; Taya, 1989; and Sharp, 1990). One of the successful reactors is nutrient mist reactor (NMR) which
is simple in design and economical for cultivation of hairy roots (Flores, 1992; Williams, 2000; Ramakrishnan,
2004; and Wilson, 1990). This is a gas phase reactor in which the liquid medium is introduced into the
bioreactor as a mist phase with very small droplets in the size range of 0.5 µm - 30 µm. NMR has definite
advantages such as easy operation, presence of gas phase, lack of shear, low pressure, ease in manipulating the
gas composition and effective gas exchange in a densely growing biomass and ease of scaling up (Towler, 2007;
and Liu, 1999). The mass transfer limitation of oxygen can be eliminated by using gas phase reactors. These are
unique because the gas composition in the reactor nvironment can be closely controlled; oxygen is not a limiting
factor and pressure drops and shear rates are both low (Weathers, 1999; and Williams, 1999). Industrial
production of secondary metabolites from hairy roots remains very challenging due to the complex fibrous
structure and dense root growth network (Srivastava, 2007). Furthermore, root growth is not homogeneous.
Growth of these valuable roots can be expressed in terms of increase in mass, number of tips and length. Also
the growth of hairy roots and the production of secondary metabolite depend on the availability and composition
of liquid media and gases at the root surface.
The availability of sufficient nutrients and oxygen to the root surface is very important for healthy
growth of root mass (Dilorio, 1992b; Dilorio, 1992b; Flores, 1992). Also, the amount of available nutrients in
this reactor is dependent upon the volume of mist which can be captured by the roots. Mist deposition is a key
step in the mass transfer of nutrients to the roots in mist bioreactors (Wyslouzil, 1997). It is important to
mention that the mist-ON/mist-OFF cycles determines the delivery of nutrients to the roots and also controls the
gas exchange in the growth chamber, and thus this parameter is critical for ensuring root tissue viability and
2. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 47
development. It is reported in literature that intermittent misting cycle helps in uniformly wetting the root
surface and the short intermittent misting cycle prevents severe clogging of the bed by previously captured
particles and allows time for liquid to drain from the roots between applications of the mist. The roots grow
well when the mist is supplied on an intermittent mist-ON/mist-OFF basis. Higher growth yields can be
achieved with increased droplet deposition and by manipulating the mist-ON/mist-OFF cycles (Towler, 2007).
It is also possible to sustain the performance by a continuous mist-ON cycle rather than an intermittent
mist-ON/mist-OFF cycles by choosing the processes conditions carefully. Once the root species is chosen then
the two major process conditions to be chosen are feed flow rate (F) and concentration of nutrients (Sucrose) in
the feed, (CF). For a continuous mist-ON cycle, the liquid holdup (H) and nutrient concentration in liquid layer
(C) reach its static values, which depend on the values of CF and F. For values of equilibrium specific liquid
holdup (HE) less than critical specific liquid holdup (HC) and equilibrium feed concentration (CE) more than
critical feed concentration (CC), the reactor can run indefinitely in the mist-ON cycle mode. HC and CC are the
maximum value of H and minimum value of C which are required to run the system in safe mode without any
mass transfer limitations of liquid and gas phase nutrients. While the reactor can now be operated without any
botheration of mist-ON/mist-OFF cycle, one misses out on the increased energy savings provided by periods of
mist-OFF cycle. In any case, intermittent cycles have to be analyzed to handle any unscheduled disruption in the
mist-ON cycle. Any estimation of the maximum cushion of down time before the mist-ON cycle must be started
is important in sustained production of hairy roots. An analysis of the intermittent mode of operation of NMR is
presented in the present contribution. It is based on numerical simulations of a mathematical model which
describes the evolution of liquid holdup and concentration.
II. Model Development And Numerical Simulations
Development of the mathematical model for an efficient operation of NMR has been shown in the
following steps and a schematic diagram of this reactor and root bed for intermittent mist ON/OFF cycle is also
shown in Fig. 1.
Fig. 1 Schematic diagrams of nutrient mist reactor and hairy root bed for intermittent mist ON/OFF cycle,
respectively
A mathematical model for the evolution of liquid holdup and feed (nutrient) concentration is
developed under the assumptions of uniform and complete mixing in the held up liquid. While, some deposition
is required for providing nutrients to the growing roots, any excess deposition will lead to increased holdup in
the form of a thick liquid layer along the root surface. This will impede gas transfer to the roots and the system
will behave as if it is a liquid phase reactor. Thus, the mist-ON cycle has to be stopped before such a condition
is reached. The deposited liquid will then reduce in volume through drainage and will result in the reduction of
mass transfer resistance. As no fresh nutrients are being fed, the deposited liquid gets depleted in nutrient
concentration resulting in reduced availability of liquid phase nutrients. Thus, the mist-OFF cycle also has to be
stopped before the concentration in the liquid layer goes below the essential level required for the specified
growth. The drainage rate has been modeled as proportional to difference between the specific dynamic liquid
holdup, volume of held up liquid divided by mass of the root bed (H), and its value at saturation (HS). The value
of proportionality constant (K2) for drainage have been taken for the literature (Raynor and Leith, 2000).
The effective feed flow rate per unit mass (F), is estimated based on the following argument. In a
typical reactor configuration, the root bed may occupy only a small fraction of the reactor volume, at least in the
early stages. The mist input flow rate at the inlet of the chamber may be held constant but the effective flow rate
into the bed may change as the root bed expands and come in contact with more mist. The effective flow rate to
the bed is likely to be governed by the relative dimensions of the bed and the reactor chamber. With the
3. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 48
dimensions of the reactor chamber remaining constant this translates to relative dimensions of the bed at
different times. One can intuitively see two extreme cases depending on whether the effective rate depends on
the relative surface area or relative volumes. If the droplet size is comparable to the void spacing between the
root hairs then most of them will deposit on the outer surface of the growing root bed. This will lead to relative
surface area dependence of the effective feed flow rate. On the other hand if the droplets are much smaller then
they will penetrate inside the bed and deposit there also, leading to a volume dependent effective feed flow rate.
Let „f0‟ and „f‟ denote the effective feed flow rate at the start (t = 0) and at any given time t, respectively. The
corresponding specific effective flow rates will be given by F0 = f0/MR0 and F = f / MR, where „MR0‟, and „MR‟
are the mass of the root bed at the start and at the given time t, respectively. If the density of the root bed
remains constant (F = F0), then the volume dependent case is characterized by
0
0
0
0
0
0
0 ; F
M
f
M
f
F
M
M
f
V
V
ff
RRR
R
(1)
F keeps on decreasing steadily for the area dependent case and expressed by
3/1
0
0
3/1
00
0
3/2
0
0
0
0 ;
R
R
R
R
RRR
R
M
M
F
M
M
M
f
M
f
F
M
M
f
A
A
ff (2)
Where MR0, and MR are the mass of the root bed at the start and at given time t, respectively. A0, V0 and A, V
represents area and volume of the root bed at start and at given time t, respectively. f0 and f denote the effective
feed flow rate at start (t = 0) and at any given time t, respectively. In general, specific feed flow rate is expressed
by
0
0
R
R
M
M
FF (3)
Where α is an exponent for effective feed flow rate, whose value depends on the size of droplets. The root
growth for first order kinetics is expressed by
R
R
M
dt
dM
(4)
Where μ = Specific growth rate of the roots and is assumed to be constant.
2.1 Development of equations for mist-ON cycle
Taking into account all the assumptions made above, a mass balance for liquid and nutrients across
the root bed after time t, is expressed by
)()exp( 20 SHHKtF
dt
dH
(5)
H
K
CCt
H
F
dt
dC
F
10
)exp(
(6)
Where K1 is rate of consumption by the roots per unit mass of the roots and K2 is proportionality constant for
drainage equation.
Analytical solution of the above set of Eqs. (4, 5 and 6) for the case of α = 0 and constant µ is
expressed by
tMM RR exp0 (7)
)exp(1 2
2
0
0 tK
K
F
HH (8)
t
F
F
tK
K
F
H
dtF
KCCF
KCCF
0
2
2
0
0
0
100
10
exp1
ln
(9)
Where MR0, H0 and C0 are the values at the start or at t = 0.
4. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 49
If one wants to operate at feed flow rates which are higher than the upper limit of H then one has to
stop the mist-ON cycle before H reaches to Hc. One can also estimate the maximum duration of mist-ON time
for continuous operation of the reactor (putting H = HC in Eq. (8) as expressed by
1
0
2
2
1ln
1
SCC HH
F
K
K
T (10)
Where TC is the maximum duration of mist-ON cycle.
The mist has to be started again when C goes down to CC. The maximum duration of the subsequent
mist-ON cycles will depend on H value at the end of the preceding mist-OFF cycle. The lower limit of H is HS.
Thus, the subsequent mist-ON cycles have to be stopped earlier than TC. As a result, TC serves as an upper limit
for durations of all mist-ON cycles.
2.2 Development of equations for mist-OFF cycle
During mist-OFF cycle, the supply of the feed is stopped therefore feed flow rate becomes zero. So the
Eqs. (5) and (6) can be expressed by
)(2 SHHK
dt
dH
(12)
H
K
dt
dC 1
(13)
Specific liquid hold up across the root bed after time t for mist-OFF cycle is expressed by
tKHHHH SCS 2exp (14)
Nutrient concentration presents in the liquid at the end of mist-OFF cycle is expressed by
HHtKHHH
HK
K
H
tK
CC SSCS
SS
E lnexpln 2
2
11
(15)
Hence the maximum duration of mist-OFF cycle for an intermittent mist-ON/mist-OFF cycle (putting t = TM
and C = CC in Eq. (14) is expressed by
HHTKHHH
HK
K
CC
K
H
T SMSCS
S
CE
S
M lnexpln 2
2
1
1
(16)
Where TM is the maximum duration of mist-OFF cycle.
Solutions for mist-ON/mist-OFF cycles were obtained by integrating the set of coupled Eqs. (5), (6),
(12) and (13), respectively in time as initial value problems by using NAG Library subroutine D02EJF. The
subroutine D02EJF is a variable order and variable time-step method which uses GEARS Algorithm to integrate
differential equations. It automatically chooses the required time steps and order. Simulations were performed
for various levels of error tolerance till the solution did not change with changing tolerance. Repeated solutions
for mist-ON cycle followed by mist-OFF cycle were used to simulate for the complete reactor. As both H and C
rise to steady state values during a continuous mist-ON cycle, the ON cycle was terminated for given values of
relative approach to steady state value of concentration (YON ), which is expressed by
NE
N
ON
CC
CC
Y
(17)
Where, CN is concentration at the start of mist-ON cycle. Similarly, mist-OFF cycle was stopped for relative
approach to the CC as YOFF and expressed by
CO
O
OFF
CC
CC
Y
(18)
Where, Co is now the concentration at the start of the mist-OFF cycle rather than that of the mist-ON cycle.
The numerical values for model parameters were estimated from the literature. Since a wide range of
such values has been reported, a suitable set is difficult to select. Consequently, parameter values were chosen
or estimated such that they were within the practical ranges for the root culture system. The values of
parameters, used to simulate the results are shown in Table 1. Simulations were performed with a large number
of parameter values with in the range of reported/practical values. The specified growth rate has to be decided
upon first. The growth rate achieved in the shake flask experiments can be a good guideline for the reasonable
values.
5. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 50
Table 1. Physical parameters used in the model
Parameters Values References
Nutrient concentration (Sucrose)
in feed, CF
50 g/L (Kim, 2001)
(Towler, 2007)
Specific growth rate, µ 0.2 day-1
(Kim, 2002)
(Towler, 2007)
Feed (Mist) flow rate, F0 0.1 mL/day/mg (Towler, 2007)
Mist droplet capture efficiency, η
0.1 (Wyslouzil, 1997)
Initial root mass, MR0 100 mg (Towler, 2007)
Density of the roots, ρR 1000 mg/mL (Towler, 2007)
Diameter of root, Df 1 mm (Wyslouzil, 1997)
Diffusivity Coefficient in liquids,
D 0.72 mm2
/day (Raynor, 2000)
Liquid film thickness, LF 0.1 mm (Raynor, 2000)
Critical concentration , CC 5 mg/mL Calculated
Specific liquid holdup at
saturation, HS 0.01 mL/mg Towler (2007)
Proportionality constant for
growth equation, K1 0.3 day-1
(Kim, 2002)
Proportionality constant for
drainage rate, K2 4 day-1
Calculated
Critical liquid holdup, Hc 0.04 mL/mg Calculated
III. Results And Discussions
The objective of the present work is to study process parameters (duration of mist-ON/ mist-OFF
cycles, feed flow rate and feed concentration) for an efficient operation of NMR. The following results are
discussed for the case when mist is supplied on intermittent mist-ON/mist-OFF basis. Fig. 1 presents the
evolution of C and H during repeated mist-ON/mist-OFF cycles for different YOFF. Other parameter values are
F0 = 0.1 mL/day/mg, CF = 50 mg/mL, K1 = 0.3 per day, K2 = 4 per day, HS = 0.01 mL/mg, HC = 0.04mL/mg, CC
= 5 mg/mL and YON = 0.99. The evolution settles into a steady almost periodic behavior very quickly. Both C
and H rise steadily towards CE and HE during the mist-ON cycle. The rate decreases as they reach close the
equilibrium values. The rise is arrested as mist-ON cycle reaches at a value, YOFF = 0.99. Both C and H start
decreasing as the mist-OFF cycle starts. Different cutoffs for mist-OFF cycle shows that the duration for mist-
OFF cycle is different in each case with larger cutoffs resulting in larger durations.
Fig. 1 The evolution of concentration and specific liquid holdup during repeated mist-ON / mist-OFF cycles for
different YOFF . Solid lines, dashed and dotted lines correspond to YOFF = 0.99, 0.75 and 0.5, respectively.
Fig. 2 presents results for the same system for a constant YOFF and variable YON. Other parameter
values are F0 = 0.1mL/day/mg, CF = 50 mg/mL, K1 = 0.3 per day, K2 = 4 per day, HS = 0.01 mL/mg, HC = 0.04
mL/mg, CC = 5 mg/mL, YOFF = 0.99. Once again the evolution looks periodic. It is interesting to see that the
6. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 51
corresponding cutoff for H is again much different from that of the C. It is observed that the evolution of C is
mostly controlled by K1 and less and indirectly controlled by K2 through H. The evolution of H on the other
hand, is governed by K2. For this particular choice of K1 and K2, H evolves faster than C. For some other
combination of K1 and K2, H may evolve at a slower rate. It is also not feasible to choose very low value of
mist-ON cycle because the system will operate closer to CC. Hence it is always feasible to operate the reactor
slightly above this value.
Fig. 2 Variation of concentration and specific liquid holdup with time for a constant YOFF and variable YON .
Solid lines, dashed and dotted lines correspond to YON = 0.99, 0.75 and 0.5, respectively.
Fig. 3 presents the variation of ratio of cumulative duration of mist-ON cycles and the total running
time (RON) with fractional value of YOFF for different process conditions. Other parameter values are F0 =
0.1mL/day/ mg, CF = 50 mg/mL, K1 = 0.3 per day, K2 = 4 per day, HS = 0.01 mL/mg, HC = 0.04 mL/mg, CC = 5
mg/mL, YOFF = 0.99-0.05, YON = 0.99. An intermittent operation is preferred over a continuous one, so that the
reactor can be operated in an economical (power saving) and feasible manner. The values of HS, HC, CC, K1, K2
have been kept constant whereas CF and F have been varied. An increase in YOFF results a decrease in RON
which also shows the increase in duration of mist-OFF cycle and corresponding decrease in mist-ON cycle. An
increase in CF leads to decrease in RON for longer duration of mist-OFF cycle. CE increases with CF and for a
constant CC, the permissible value of the concentration decay during the mist-OFF cycle is higher. It is also
observed that an increase in Fo, leads to decrease in RON. Also, higher value of F leads to a shorter duration of
mist-On cycles as the required buildup of the concentration is achieved at a faster rate. It does not effect mist-
OFF cycle duration as CE , CC and the decay of concentration during mist-OFF cycle remains unchanged. It is
also observed that there is no influence of CF on the decay rate.
Fig. 4 Variation of ratio of cumulative duration of mist-ON cycles and the total time (RON) with fractional value
of YOFF for different values of CF and F, respectively. Solid lines, dashed, small dash and dotted lines
correspond to CF = 60, 50, 25 and 10 mg/mL, F = 0.05, 0.1, 0.2, 0.3 mL/day/mg, respectively.
7. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 52
Fig. 5 and Fig. 6 present the effect of the drainage constant K2. Other parameter values are F0 =
0.1mL/day/mg, CF = 50 mg/mL, K1 = 0.3 per day, HS = 0.01 mL/mg, HC = 0.04 mL/mg, CC = 5 mg/mL, YOFF =
0.99, YON = 0.99. The results for K2 = 1 per day have already been presented in previous graphs. The evolutions
of C and H are presented in Fig. 5. The variation of ratio RON with YOFF is presented in Fig. 6. It is observed that
increasing the value of K2 or drainage will result decrease in liquid holdup (Eq. (5)). During this period, HE is
also reduced (Eq. (6)), whereas CE is not affected at all (Eq. (7)). This is corroborated by the results shown in
Fig. 5 where solid, dashed, short dashed and dotted lines show progressively smaller slopes for both in the
buildup and decay branches. The corresponding mist cycle durations are also reduced. The overall change in
concentration remains constant in each cycle as the cutoff are in terms of equilibrium and critical concentrations
which are not affected by change in K2. Thus, faster rates translate to faster cycle durations. The rate of change
of liquid holdup decreases as holdup reaches the saturation value. The dotted line in Fig. 5 for K2 = 16 per day
shows that most of the down cycle is carried out at liquid holdups close to HS which is resulting in higher rate
of change in concentration value. The duration of both the cycles are affected by the drainage rates. Depending
on which cycle is affected more, the ratio RON will change likewise. The somewhat erratic behavior (Fig. 6) of
RON, where it first increases and then decreases with K2, proves this point and emphasizes the necessity of
numerical simulation.
Fig. 5 Variation of concentration and specific liquid holdup with time for a constant YOFF and variable K2. Solid
lines, dashed, small dashed and dotted lines correspond to K2 = 2, 4, 8, 16 per day, respectively.
Fig. 6 Variation of ratio of cumulative duration of mist-ON cycles and the total running time (RON)
with fractional value of YOFF for different value of K2 . Solid lines, dashed, small dash and dotted lines
correspond to K2 = 2, 4, 8, 16 per day, respectively.
IV. Conclusions
A mathematical model has been developed to study the process conditions for an efficient operation of
NMR for the growth of hairy roots. It is based on a theoretical model of NMR at the root bed level and its
numerical simulation. This model describes the evolution of liquid holdup and concentration present in the root
bed. This analytical solution to the model can lead to run the reactor with intermittent mist-ON and mist-OF
cycles, at very low cumulative mist-ON duration for any given total run time to prevent any nutrient deficiency
and water logging in the bed. Higher flow rates will lead to water logging and lower flow rates can lead to
8. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 53
unacceptable high feed concentrations. Lower mist concentrations lead to requirement of high flow rates which
may again lead to water logging. Thus, mist concentration has to be more than a critical value and flow rate has
to lie within a range for operating a reactor in continuous mist-ON mode. Numerical simulations are used to
understand the reactor performance for intermittent mist-ON and mist-OFF mode. A reasonable cut-off criterion
for switching between ON-OFF cycles can be in terms of fractional approach to the end concentration for each
cycle. The end concentration for mist-ON cycle is the equilibrium concentration and that for the mist-OFF cycle
is the critical concentration. The gross efficiency of the reactor operation can be given in terms of the ratio of
cumulative durations of the mist-ON cycles to total runtime, RON. In some cases, it assumes very low value of
10% meaning that the mist can be switched off for 90% of the time. The duration of both the mist-ON and mist-
OFF cycles are effected by the process parameters and thus, the ratio RON, may not follow any fixed trend in
some cases. It is expected that these guidelines presented here will help in efficient operation and design of
NMRs. More experimental data is needed to study the engineering aspect of hairy root technology in detail in
future.
Acknowledgements
The authors wish to express their sincere thanks to the Department of Science & Technology (D.S.T.),
Government of India, New Delhi, India for providing financial support for this project work.
REFERENCES
[1]. Aird, E. L., Hamill, J. D. and Rhodes. M. J. C. (1988) : “ Cytogenetic analysis of hairy root cultures from a number of plant
species transformed by Agrobacterium rhizogenes”, Plant Cell Tiss. Organ Cult. Vol. 15, pp 47-57.
[2]. Carvalho, E. V. and Curtis, W.R. (1998) : “Characterization of fluid-flow resistance in root cultures with a convective flow
tubular reactor”, Biotechnol. Bioeng. 1998, Vol. 60, pp 375-383.
[3]. Dilorio, A. A, Cheetham, R. D.and Weathers. P. J. (1992a) : “Growth of transformed roots in a nutrient mist bioreactor : reactor
performance and evaluation”, Appl. Microbiol. Biotechnol. Vol. 37, pp 457-462.
[4]. Dilorio, A. A,. Cheetham, R. D and Weathers. P. J. (1992b) : “Carbon dioxide improves the growth of hairy root cultured on
solid medium and in nutrient mists”, Appl. Microbiol. Biotechnol. Vol. 37, pp 463-467.
[5]. Eibl, R. and Eibl, D. (2006) : “Design and use of wave bioreactor for plant cell culture”, In: Dutta Gupta S, Ibaraki Y (eds.) Plant
tissue culture engineering, series: Focus on Biotechnol. Vol. 6, pp 203-227.
[6]. Ferreira, J.F.S, Laughlin, J. C., Delabays, N. and de Magalhaes, P. M. (2005) : “Cultivation and Genetics of Artemisia annua L.
for the Increased Production of the Antimalarial Artemisinin”, .Plant Genetic Resources: characterization and utilization, Vol.3,
pp 206-229.
[7]. Flores, H. E. and Curtis, W. R. (1992) : “"Approaches to understanding and manipulating the biosynthetic potential of plant
roots", In: Biochemical Engineering VII: Cellular and Reaction Engineering”, Annals of the New York Academy of Sciences,
Vol. 665, pp 188-209.
[8]. Guillon, S., Tremouillaux-Guiller, J., Pati, P., Rideau, M and Gantet, P. (2006) : “Hairy root research: recent scenario and
exciting prospects”, Curr. Opin. Plant Biol. 2006, Vol. 9, pp 341-346.
[9]. Hilton, M. G., and Rhodes. M. J. C. (1990) : “Growth and hyoscyamine production of “hairy root” cultures of Datura
Stramonium in a modified stirred tank reactor”, Appl. Microbial. Biotechnol. Vol. 33, pp 132-138.
[10]. Kenneth D. G., and Thomas. N. H. (1996) “An integrated “Root Tube” bioreactor/Separator for transformed root cultures”, J
ferment. Bioeng. Vol. 81, pp 453-457.
[11]. Kim, Y., Wyslouzil, B.E. and Weathers, P.J. (2001) : “A comparative study of mist and bubble column reactors in the in vitro
production of artemisinin”, Plant Cell Rep. Vol. 20, pp 451-455.
[12]. Kim, Y., Wyslouzil, B.E and Weathers, P.J, (2002) : “Secondary metabolism of hairy root cultures in biorecators”, In Vitro Cell
Dev. Biol. Plant. 2002, Vol. 38, pp 1-10.
[13]. Kim, Y., Wyslouzil, B. E. and Weathers. P. J. (2002) : “Growth of Artemisia annua hairy roots in liquid and gas-phase reactors”,
Biotechnol. Bioeng. Vol. 80, pp 454-461.
[14]. Liu, C. Z., Wang, Y. C., Zhao, B., Guo, C., Ouyang, F., Ye, H. C. and Li, G. E. (1999) : “Development of a nutrient mist
bioreactor for growth of hairy roots”, In Vitro Cellular Develop Biol. Vol. 35, pp 271-274.
[15]. Lorence, A., Medina-Bolivar, F. and Nessler, C. L. (2004) : “Camptothecin and 10-hydroxycamptothecin from Camptotheca
acuminata hairy roots “, Plant Cell Rep. Vol. 22, pp 437-441.
[16]. McAlister, B., Finnie, J. and Watt, F. M. P. (2005) : “Use of the temporary immersion bioreactor system (RITA®
) for production
of commercial Eucalyptus clones in Mondi Forests (SA)”, Plant Cell Tissue Organ Cult. Vol. 81, pp 347 - 358.
[17]. Parr, A.J., Peerless, A. C. J., Hamill, J. D., Walton, N. J., Robins, R. J. and Rhodes, M. J. C. (1988) : “Alkaloid production by
transformed root cultures of Catharanthus roseus”, Plant Cell Rep. Vol. 7, pp 309-312.
[18]. Palazon, J., Mallol, A., Eibl, R., Lettenbaur, C., Cusido, R. M. and Pinol, M. T. : “Growth and ginsenoside production in hairy
root cultures of Panax ginseng using a novel bioreactor”, Planta Med. Vol. 69, pp 344-349.
[19]. Pavlov, A. and Bley, T. (2005) : “Betalains biosynthesis by Beta vulgaris L. hairy root culture in different bioreactor systems.
Scientific Works”, Scientific Works, University of Food Technologies, Vol. 52, pp 299-304.
[20]. Pavlov, A. and Bley, T. (2006) : “Betalains biosynthesis by Beta vulqarrs L. hairy root culture In a temporary inmersion
cultivation system “, Process Biochem. Vol. 41, pp 848- 852.
[21]. Ranjan R. and Mishra, B. (2009) : “Growth of hairy root cultures in various bioreactor for the production of secondary
metabolites”, Biotechnol. Appl. Biochem. Vol. 49, pp 1-10.
[22]. Ramakrishnan, D. and Curtis, W. R. (2004) : “Trickle-bed root culture bioreactor design and scale-up: growth”, Biotechnol.
Bioeng. Vol. 88, pp 248-260.
[23]. Raynor, P. C., and Leith, D. (2000) : “The influence of accumulated liquid on fibrous filter performance”, J Aerosol Sci. Vol.
31, pp 19-34.
[24]. Raynor, P. C., and Leith, D. (2000) : “The influence of accumulated liquid on fibrous filter performance”, J Aerosol Sci. Vol.
31, pp 19-34.
9. A strategy to choose process parameters for sustained operation of nutrient mist reactor to grow….
www.ijeijournal.com Page | 54
[25]. Sevon, N. and Oksman-Caldentey, K.M. (2002) : “Agrobacterium rhizogenes-mediated transformation: root cultures as a source
of alkaloids”, Planta Med. Vol. 68, pp 859-868.
[26]. Shanks, J. V. and Morgan, J. (1999) : “Plant 'hairy root' culture”, Curr. Opin. in Biotechnol. Vol. 10, pp 151-155.
[27]. Sharp, J. M. and Doran, P. M. (1990) : “Characteristics of growth and tropane alkaloid synthesis in Atropa Belladona roots
transformed by Agrobacterium rhizogenes”, J. Biotechnol. Vol. 16, pp 171-186.
[28]. Sivakumar, G. (2006) : “Biorecator technology: a novel industrial tool for high tech production of bioactive molecules and
biopharmaceuticals from plant roots”, Biotechnol. J. Vol. 1, 1419 - 1427.
[29]. Souret, F. F., Kim, Y., Wyslouzil, B. E., Wobbe, K. K. and Weathers, P.J. (2003) : “Scale-up of Artemisia annua L. hairy root
cultures produces complex patterns of terpenoid gene expression”, Biotechnol. Bioeng. Vol. 83, pp 653-667.
[30]. Srivastava, S. and Srivastava, A. (2007) : “Hairy root culture for mass-production of high-value secondary metabolites”, Crit.
Rev. Biotechnol. Vol.27, pp 29-43.
[31]. Sudha, C. G., Obul Reddy, B., Ravishankar, G. A. and Seeni, S. (2003) : “Production of ajmalicine and ajmaline in hairy root
cultures of Rauvolfia micrantha Hook f., a rare and endemic medicinal plant.”, Biotechnol. Lett. Vol. 25, pp 631-636.
[32]. Taya, M. A., Yoyama., O., Kondo., T., Kobayashi, C. and Matsui. C. (1989) : “Growth characteristics of plant hairy roots and
their cultures in bioreactors”, J Chem. Eng. Jpn. Vol. 22, pp 84- 89.
[33]. Towler, M. J., Wyslouzil, B. E. and Weathers, P. J. (2007) : “Using an aerosol deposition model to increase hairy root growth in
a mist reactor”, Biotechnol. Bioeng. Vol. 96, pp 881-891.
[34]. Verma, S and Singh, S. P. (2008) : “Current and future status of herbal medicines”, Vet. World, Vol.1, pp 347-350.
[35]. Weathers, P. J., Wyslouzil, B. E., Wobbe, K. K., Kim, Y. J.and Yigit, E. (1999) : “Workshop on bioreactor technology. The
biological response of hairy roots to O2 levels in bioreactors “, In Vitro Cell. Dev. Biol. Plant, Vol. 35, pp 286-289.
[36]. Weathers, P.and Bunk McCoy, M. C. (2005) : “The effect of phytohormones on growth and artemisinin production in Artemisia
annua hairy roots”, In Vitro Cell Dev. Biol. Plant Vol. 41, pp 47-53.
[37]. Williams, G. R. C. and Doran, P. M. (1999) : “Investigation of liquid–solid hydrodynamic boundary layersand oxygen
requirements in hairy root cultures”, .Biotechnol. Bioeng., Vol. 64, pp 729-740.
[38]. Williams, G. R. C. and Doran, P. M. (2000) : “Hairy root culture in a liquid-dispersed bioreactor: characterization of spatial
heterogeneity”, Biotechnol. Prog. Vol. 16, pp 391- 409.
[39]. Wilson, P. D.G., Hilton, M. G., Meechan, P. T. H., Waspe, C. R. and Rhodes, M. J. C. (1990) : “The cultivation of transformed
roots from laboratory to pilot plant”, Progress in plant cellular and molecular biology, Kluwer, Amsterdam, pp 700-705.
[40]. Wyslouzil, B. E., Whipple, M., Chatterjee, C., Walcerz, D. B. and Weathers, P. J. (1997) : “Mist deposition onto hairy root
cultures : Aerosol modeling and experiments”, Biotechnol. Prog. Vol. 13, pp 185-194.